Digital Monitoring Products XR500 Series Operating instructions

Programming guide
Xr500 SerieS
Control Panel

MODEL XR500 SERIES
CONTROL PANEL PROGRAMMING GUIDE
Contains programming Instructions for use with the
Model XR500, XR500N, XR500E Series Control Panels
XR500FC, XR500NFC Series Fire Control Panels
When using the XR500 Series panel for any UL, NFPA, CSFM, or other listing organization’s approved methods, refer to this
manual and the XR500 Series Installation Guide (LT-0681), or XR500FC Series Installation Guide (LT-1088). These documents
outline the installation and programming requirements of all applications for which the XR500 Series is approved.
FCC NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at this own expense.
© 2014 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice.

XR500 Series Programming Guide Digital Monitoring Products
i
Table Of COnTenTs
Introduction......................................................................1
1.1 Before you Begin ................................................................. 1
1.2 Getting Started.................................................................... 1
1.3 Encrypted Communications (XR500N/XR500E only)................ 2
1.4 Programmer Operation......................................................... 2
1.5 Programmer Lockout Codes.................................................. 2
1.6 Reset Timeout ..................................................................... 2
1.7 Power Up ............................................................................ 2
1.8 Keypads.............................................................................. 3
1.9 Special Keys ........................................................................ 3
1.10 Entering Alpha Characters .................................................... 4
1.11 Entering Non-Alpha Characters ............................................. 4
1.12 Keypad Displays Current Programming .................................. 4
1.13 Multiple Displays.................................................................. 5
1.14 Asterisks in Programming..................................................... 5
1.15 Compliance Instructions (ANSI/UL 864)................................. 5
Initialization......................................................................6
2.1 Initialization ........................................................................ 6
2.2 Clear All Memory ................................................................. 6
2.3 Clear All Codes .................................................................... 6
2.4 Clear All Schedules .............................................................. 6
2.5 Clear Display Events Memory................................................ 6
2.6 Clear Zone Information ........................................................ 6
2.7 Clear Area Information......................................................... 6
2.8 Clear Output Information ..................................................... 6
2.9 Clear Communication and Remote Options ............................ 6
2.10 Set to Factory Defaults......................................................... 6
Communication.................................................................7
3.1 Communication ................................................................... 7
3.2 Account Number.................................................................. 7
3.3 Transmit Delay .................................................................... 7
3.4 Communication Path ............................................................ 7
3.5 Communication Type............................................................ 7
3.6 Path Type............................................................................ 7
3.7 Test Report ......................................................................... 8
3.8 Test Frequency .................................................................... 8
3.9 Test Day ............................................................................. 8
3.10 Test Time............................................................................ 8
3.11 Check In ............................................................................. 8
3.12 Fail Time............................................................................. 8
3.13 Encryption (XR500E only)..................................................... 8
3.14 Receiver IP.......................................................................... 8
3.15 Receiver Port....................................................................... 8
3.16 First Telephone Number ....................................................... 8
3.17 Second Telephone Number................................................... 9
3.18 Advanced Programming ....................................................... 9
3.19 First GPRS APN.................................................................... 9
Second GPRS APN ............................................................... 9
3.20 Fail Test Hours..................................................................... 9
3.21 Protocol .............................................................................. 9
3.22 Retry Seconds ..................................................................... 9
3.23 Substitution Code ...............................................................10
3.24 232 Communication Port .....................................................10
3.25 232 Setup String.................................................................10
3.26 893A..................................................................................10
3.27 Alarm Switch ......................................................................10
3.28 Duplicate Alarms.................................................................10
3.29 Alarm Reports ....................................................................10
3.30 Supervisory/Trouble Reports................................................11
3.31 Opening/Closing and User Reports.......................................11

Digital Monitoring Products XR500 Series Programming Guide
ii
Table of ConTenTs
3.32 Door Access Report.............................................................11
3.33 Panic Test (XR500N/XR500E only) .......................................11
3.34 Send Communication Trouble ..............................................11
3.35 Send Path Information ........................................................11
Network Options (XR500N/XR500E only) ........................... 12
4.1 DHCP Mode Enabled ...........................................................12
4.2 Local IP Address.................................................................12
4.3 Gateway Address................................................................12
4.4 Subnet Mask ......................................................................12
4.5 DNS Server ........................................................................12
4.6 Passphrase (XR500E only) ...................................................... 12
4.7 734N Listen Port.................................................................12
4.8 734N Passphrase ................................................................12
Messaging Setup.............................................................13
5.1 Messaging Setup ................................................................13
5.2 Enable Messaging ...............................................................13
5.3 System Name .....................................................................13
5.4 Destination 1......................................................................13
5.5 Destination 1 User Number..................................................13
5.6 Destination 2......................................................................13
5.7 Destination 2 User Number..................................................13
5.8 Destination 3......................................................................13
5.9 Destination 3 User Number..................................................13
5.10 Email Communication Type..................................................14
5.11 O/C Email ..........................................................................14
5.12 O/C SMS ............................................................................14
5.13 Monthly Limit .....................................................................14
5.14 SMTP Server ......................................................................14
5.15 SMTP Server Port................................................................14
5.16 SMTP Username .................................................................14
5.17 SMTP Password ..................................................................14
5.18 From Email Address ............................................................14
Device Setup ...................................................................15
6.1 Device Setup ......................................................................15
6.2 Device Number...................................................................15
6.3 Device Name......................................................................15
6.4 Device Type .......................................................................15
6.5 Device Communication Type................................................15
6.6. Serial Number ....................................................................15
6.6.1 Supervision Time ................................................................15
6.7 Access Areas ......................................................................15
6.8 Egress Areas ......................................................................16
6.9 Display Areas .....................................................................16
6.10 Strike Time.........................................................................17
6.11 Strike Delay........................................................................17
6.12 Fire Exit Release.................................................................17
6.13 Output Group .....................................................................17
6.14 Schedule Override ..............................................................18
6.15 Auto Force Arm Device? ......................................................18
6.16 Door Real-Time Status?.......................................................18
6.17 Send Door Forced Message?................................................18
6.18 Program 734/734N Options .................................................18
6.18.1 Activate Zone 2 Bypass .......................................................18
6.18.2 Zone 2 Bypass Time............................................................18
6.18.3 Relock on Zone 2 Change? ..................................................18
6.18.4 Activate Zone 3 Request to Exit ...........................................19
6.18.5 Zone 3 REX Strike Time.......................................................19
6.18.6 Activate Onboard Speaker ...................................................19
6.18.7 Card Options ......................................................................19
6.18.8 Weigand Code Length .........................................................19

XR500 Series Programming Guide Digital Monitoring Products
iii
Table Of COnTenTs
6.18.9 Site Code Position...............................................................20
6.18.10 Site Code Length ................................................................20
6.18.11 User Code Position..............................................................20
6.18.12 User Code Length ...............................................................20
6.18.13 Require Site Code ...............................................................20
6.18.13.1 Site Code Display...............................................................20
6.18.14 Number of User Code Digits ................................................20
6.18.15 No Communication with Panel .............................................21
Remote Options ..............................................................22
7.1 Remote Options..................................................................22
7.2 Remote Key........................................................................22
7.3 Remote Disarm...................................................................22
7.4 Armed Answer Rings...........................................................22
7.5 Disarmed Answer Rings.......................................................22
7.6 PC Modem .........................................................................22
7.7 Alarm Receiver Authorization ...............................................22
7.8 Service Receiver Authorization .............................................22
7.9 Manufacturer Authorization .................................................23
7.10 Allow Network Remote........................................................23
7.10.1 Network Programming Port..................................................23
7.10.2 Encrypt Network Remote.....................................................23
7.11 Allow Cellular Remote .........................................................23
7.11.1 First GPRS APN...................................................................23
Second GPRS APN ..............................................................23
7.11.2 Encrypt Cellular Remote ......................................................23
7.12 Allow RS-232 Remote..........................................................23
7.13 Entré Connection ................................................................23
7.13.1 Entré Incoming TCP Port .....................................................23
7.13.2 Entré IP Address.................................................................23
7.13.3 Entré Outbound TCP Port ....................................................23
7.13.4 Entré Backup IP Address .....................................................24
7.13.5 Entré Backup TCP Port ........................................................24
7.13.6 Entré Checkin.....................................................................24
7.13.7 Entré Passphrase ................................................................24
7.14 Send Local Changes............................................................24
7.14.1 Remote Change IP..............................................................24
7.14.2 Remote Change Port ...........................................................24
7.14.3 Remote Telephone Number .................................................24
System Reports...............................................................25
8.1 System Reports ..................................................................25
8.2 Abort Report ......................................................................25
8.3 Restoral Reports .................................................................25
8.4 Bypass Reports...................................................................25
8.5 Schedule Change Reports....................................................25
8.6 Code Change Reports .........................................................25
8.7 Access Keypads ..................................................................25
8.8 Ambush .............................................................................25
System Options ...............................................................26
9.1 System Options ..................................................................26
9.2 System ..............................................................................26
9.3 Instant Arming ...................................................................26
9.4 Closing Wait .......................................................................26
9.5 Entry Delay 1 .....................................................................26
9.6 Cross Zone Time.................................................................27
9.7 Zone Retard Delay ..............................................................27
9.8 Power Fail Delay .................................................................27
9.9 Swinger Bypass Trips ..........................................................27
9.10 Reset Swinger Bypass .........................................................27
9.11 Time Zone Changes ............................................................27
9.12 Latch Supervisory Zones......................................................28

Digital Monitoring Products XR500 Series Programming Guide
iv
Table of ConTenTs
9.13 Programming Menu Language .............................................28
9.14 User Menu and Status List Language....................................28
9.15 Bypass Limit.......................................................................29
9.16 Card Plus PIN (XR500E only) ...............................................29
9.17 House Code........................................................................29
9.18 Detect Wireless Jamming ....................................................29
9.19 Wireless Audible Annunciation .............................................30
9.20 Enable Keypad Panic Keys ...................................................30
9.21 Occupied Premises..............................................................30
9.22 Enhanced Zone Test............................................................30
9.23 Send 16 Character Names ...................................................30
9.24 Keypad Armed LED .............................................................30
9.25 Use False Alarm Question....................................................30
9.26 Allow Own User Code Change..............................................31
9.27 Panic Supervision................................................................31
9.28 Weather Zip Code...............................................................31
Bell Options.....................................................................32
10.1 Bell Options........................................................................32
10.2 Bell Cutoff Time..................................................................32
10.3 Automatic Bell Test .............................................................32
10.4 Bell Output.........................................................................32
10.5 Bell Action..........................................................................32
10.5.1 Fire Bell Action ...................................................................32
10.5.2 Burglary Bell Action.............................................................32
10.5.3 Supervisory Bell Action........................................................32
10.5.4 Panic Bell Action .................................................................32
10.5.5 Emergency Bell Action.........................................................32
10.5.6 Auxiliary 1 Bell Action..........................................................32
10.5.7 Auxiliary 2 Bell Action..........................................................32
Output Options................................................................33
11.1 Output Options...................................................................33
11.2.1 Cutoff Output .....................................................................33
11.2.2 Output Cutoff Time.............................................................33
11.3 Communication Trouble Output............................................33
11.4 Fire Alarm Output ...............................................................33
11.5 Fire Trouble Output.............................................................33
11.6 Panic Alarm Output.............................................................33
11.7 Ambush Output ..................................................................33
11.8 Entry Output ......................................................................34
11.9 Exit Output.........................................................................34
11.10 Ready Output .....................................................................34
11.11 Telephone Trouble Output ...................................................34
11.12 Late To Close Output ..........................................................34
11.13 Device Fail Output ..............................................................34
11.14 Sensor Reset Output...........................................................34
11.15 Closing Wait Output ............................................................34
11.16 Arm-Alarm Output ..............................................................34
11.17 Supervisory Alarm Output ...................................................34
Output Information ........................................................35
12.1 Output Information.............................................................35
12.2 Output Number ..................................................................35
12.3 Output Name .....................................................................35
12.4 Output Real-Time Status .....................................................35
12.5 Serial Number ....................................................................35
12.6 Supervision Time ................................................................35
12.7 Trip with Panel Bell Option...................................................35
Output Groups ................................................................36
13.1 Output Groups....................................................................36
13.2 Group Number....................................................................36

XR500 Series Programming Guide Digital Monitoring Products
v
Table Of COnTenTs
13.3 Group Name.......................................................................36
13.4 Output Number ..................................................................36
Menu Display...................................................................37
14.1 Menu Display......................................................................37
14.2 Armed Status .....................................................................37
14.3 Time..................................................................................37
14.4 Arm/Disarm........................................................................37
Status List .......................................................................38
15.1 Status List..........................................................................38
15.2 Display Keypads .................................................................38
15.3 System Monitor Troubles .....................................................38
15.4 Fire Zones ..........................................................................38
15.5 Burglary Zones ...................................................................39
15.6 Supervisory Zones ..............................................................39
15.7 Panic Zones........................................................................39
15.8 Emergency Zones ...............................................................39
15.9 Auxiliary 1 Zones ................................................................39
15.10 Auxiliary 2 Zones ................................................................39
15.11 Communication Trouble.......................................................39
Printer Reports ...............................................................40
16.1 Printer Reports ...................................................................40
16.2 Arm and Disarm Reports .....................................................40
16.3 Zone Reports......................................................................40
16.4 User Command Reports.......................................................40
16.5 Door Access Reports ...........................................................40
16.6 Supervisory Reports............................................................40
PC Log Reports................................................................41
17.1 PC Log Reports...................................................................41
17.2 Communication Type...........................................................41
17.3 Net IP Address ...................................................................41
17.4 Net Port .............................................................................41
17.5 232 Communication Port .....................................................41
17.6 232 Setup ..........................................................................41
17.7 Arm and Disarm Reports .....................................................41
17.8 Zone Reports......................................................................41
17.9 User Command Reports.......................................................41
17.10 Door Access Reports ...........................................................41
17.11 Supervisory Reports............................................................42
17.12 PC Log Real-Time Status .....................................................42
Area Information ............................................................43
18.1 Area Information ................................................................43
18.2 Exit Delay...........................................................................43
18.3 Burglary Bell Output............................................................43
18.4 Opening/Closing Reports .....................................................43
18.5 Closing Check.....................................................................44
18.6 Closing Code ......................................................................44
18.7 Any Bypass ........................................................................44
18.8 Area Schedules...................................................................44
18.9 Early Morning Ambush (XR500N/XR500E only)......................44
18.10 Area Number......................................................................44
18.10.1 All/Perimeter Programming..................................................44
18.10.2 Home/Sleep/Away Programming..........................................44
18.11 Area Name.........................................................................45
18.12 Account Number.................................................................45
18.13 Automatic Arming ...............................................................45
18.14 Bad Zones..........................................................................45
18.15 Automatic Disarming...........................................................45
18.16 Armed Output Number........................................................45
18.17 Late Output Number ...........................................................46

Digital Monitoring Products XR500 Series Programming Guide
vi
Table of ConTenTs
18.18 Late Arm Delay...................................................................46
18.19 Bank Safe & Vault (XR500N/XR500E only) ............................46
18.20 Common Area ....................................................................46
18.21 Arm First Area ....................................................................46
18.22 Two Man Rule (XR500N/XR500E only)..................................46
Zone Information............................................................47
19.1 Zone Information................................................................47
19.2 Zone Number .....................................................................47
19.3 Zone Name ........................................................................47
19.4 Zone Type ..........................................................................48
19.5 Area Assignment.................................................................48
19.6 Fire Bell Output ..................................................................48
19.7 Arming Zone Area Assignment .............................................48
19.8 Style..................................................................................49
19.9 Next Zone ..........................................................................49
DMP Wireless ..................................................................................50
19.10 Wireless.............................................................................50
19.10.1 Serial Number Entry............................................................50
19.10.2 Contact..............................................................................50
19.10.3 Supervision Time ................................................................50
19.10.4 LED Operation....................................................................51
19.10.5 Disarm/Disable ...................................................................51
19.10.6 PIR Pulse Count..................................................................51
19.10.7 PIR Sensitivity ....................................................................51
19.11 1100 Series Key Fobs..........................................................51
19.11.1 Key Fob User Number .........................................................51
19.11.2 Key Fob Serial Number........................................................52
19.11.3 Key Fob Supervision Time ...................................................52
19.11.4 Number of Key Fob Buttons.................................................52
19.11.5 Key Fob Button Selection (Four Buttons)...............................52
19.11.6 Key Fob Button Selection (Two Buttons) ...............................52
19.11.7 Button Action .....................................................................52
19.11.8 Button Press Time ..............................................................53
19.11.9 Arm/Disarm Area Selection..................................................53
19.11.10 Output Number ..................................................................53
19.11.11 Output Action.....................................................................54
19.11.12 Next Zone ..........................................................................54
FA Series Wireless ............................................................................54
19.12 Wireless.............................................................................54
19.12.1 Check-in Time ....................................................................54
19.12.2 Internal Contact .................................................................54
19.12.3 End-of-Line ........................................................................54
19.12.4 Normally Open ...................................................................55
19.12.5 Next Zone ..........................................................................55
19.13 Alarm Action.......................................................................55
19.14 Disarmed Open ..................................................................55
19.15 Report to Transmit..............................................................55
19.16 Output Number ..................................................................56
19.17 Output Action.....................................................................56
19.18 Swinger Bypass ..................................................................56
19.19 Prewarn Keypad Addresses..................................................56
19.20 Entry Delay ........................................................................56
19.21 Zone Retard Delay ..............................................................57
19.22 Presignal Keypad Addresses ................................................57
19.23 Fast Response ....................................................................57
19.24 Cross Zone.........................................................................57
19.25 Priority...............................................................................57
19.26 Fire Panel Slave Input .........................................................57
19.27 Area Follower .....................................................................57
19.28 Zone Real-Time Status ........................................................57

XR500 Series Programming Guide Digital Monitoring Products
vii
Table Of COnTenTs
19.29 Zone Audit Days .................................................................57
19.30 Report with Account Number for Area ..................................58
Stop.................................................................................59
20.1 Stop ..................................................................................59
Set Lockout Code ............................................................59
21.1 Set Lockout Code................................................................59
Feature Upgrade .............................................................60
22.1 Feature Upgrade.................................................................60
22.1.1 Encryption..........................................................................60
22.1.2 All No Yes Option................................................................60
22.1.3 Service User Authentication.................................................60
Purchasing Feature Upgrades ..............................................60
Appendix .........................................................................61
23.1 False Alarm Reduction.........................................................61
23.2 Diagnostics function............................................................61
23.3 Using the 984 Command Function........................................63
23.4 Using the Walk Test ............................................................63
23.5 Keypad Speaker Operation ..................................................65
23.6 Cross Zoning ......................................................................65
23.7 Events Manager..................................................................66
23.8 UserProles.......................................................................66
23.9 UserProlesRecord............................................................66
23.10 FA Series Transmitter Information ........................................66
23.10.1  WirelessCheck-inandSupervisionDenitions
23.11 Keypad Bus and LX-Bus Zone Type Descriptions....................68
23.12 ZoneTypeSpecications .....................................................68
23.12.1 Keypad Bus Zone Type Defaults ...........................................69
23.12.2 LX-Bus Zone Type Defaults ..................................................70
23.13 Common Keypad Messages .................................................71
23.14 Area Account Number Messages ..........................................72
Revisions to This Document............................................73
Listings and Approvals....................................................74

Digital Monitoring Products XR500 Series Programming Guide
viii

XR500 Series Programming Guide Digital Monitoring Products
1
IntroductIon
Introduction
1.1 Before you Begin
This guide provides programming information for the DMP XR500, XR500N, and XR500E panels. After this
Introduction, the remaining sections describe the functions of each programming menu item along with the
available options. Before starting to program, we recommend that you read through the contents of this
guide. The information contained here allows you to quickly learn the programming options and operational
capabilities of the XR500, XR500N, and XR500E panels.
In addition to this guide, you should also read and be familiar with the following XR500 Series documents:
• XR500 Series Installation Guide (LT-0681)
• XR500 Series Programming Sheet (LT-0678)
• XR100/XR500 Security Command® User’s Guide (LT-0683)
Internal Programmer
The panel contains all of its programming information in an on-board processor and does not require an external
programmer. You can perform all programming tasks through a 32-character DMP alphanumeric keypad set to
address one.
Programming Information Sheet
Included with each panel are the Programming Information Sheets. These list the various programming prompts
and available options for programming the panel. Before starting to program, we recommend you completely ll
out each sheet with the programming options you intend to enter into the panel.
Having completed programming sheets available before entering data helps prevent errors and can shorten the
time you spend programming. Completed sheets also provide you with an accurate panel program record you
can keep on le for future system service or expansion. The remainder of this Introduction provides instructions
for starting and ending a programming session using the alphanumeric keypad.
1.2 Getting Started
Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before touching
the panel to discharge static.
Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or
connecting any modules, cards, or wires to the panel.
Before starting to program the XR500 Series panel, make sure the panel is properly grounded and AC and battery
power is applied to the appropriate panel terminals. All wiring connections and grounding instructions are
detailed in the XR500 Series Installation Guide (LT-0681).
Program from any Keypad Address or Wireless Keypad
You can program the XR500 panel from any 32-character wireless keypad or hardwired keypad connected to the
panel’s keypad data bus. See the XR500 Installation Guide for keypad addressing and installation information for
hardwired keypads.
Wireless Keypads can be used for panel programming after being programmed in the panel manually or by using
the Wireless Keypad Association operation.
To enable association operation in the keypad, access the Installer Options Menu (3577 (INST)) and select RF
Survey. The keypad logo LEDs turn on Red until association is successful.
To enable association operation in the XR500 panel, reset the panel 3 times within 12 seconds. Allow the panel’s
keypad bus Transmit/Receive LEDs to turn back on between each reset.
For 60 seconds the panel listens for wireless keypads that are in the Installer Options Menu and have not been
programmed, or associated into another panel. Those keypads are assigned to the rst open device position
automatically based upon the order in which they are detected. The keypad logo turns Green to indicate it
has been associated with the panel. See the 9000
Series Wireless Keypad Installation Guide (LT-1107) for
additional information.
Accessing the Programmer
1. Momentarily place the Reset jumper over both
of the J16 pins to reset the panel.
2. Enter the code 6653 (PROG) and press
COMMAND.
3. The keypad displays: PROGRAMMER.
J6
Interface
Card
Expansion
Connector
To enable Wireless Keypad
Association operation:
Reset panel 3 times within
12 seconds.
To access the programmer:
Momentarily place the
Reset jumper over both of
the J16 pins to reset the
panel.
AC
12345678 10 11 12 13 14 15 16 17 18 19
92
02122 23 24 25 26 27 28
+B BELL GND SMK GNDRED YEL GRN BLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND
K6 K7
Output 1 Output 2
J3
Phone Line
J10
J22
LX-Bus
Battery
Start
J23
J21
RS-232
Power
LED
J8
PROG
J4
Tamper
J16
Reset
Out1 Out2
Outputs 3-6
J11
3
4
5
6
J2
J1
Ethernet
R
L
XOVC
Link LED
Activity LED
Figure 1: XR500 Series Panel Showing Reset

Digital Monitoring Products XR500 Series Programming Guide
2
IntroductIon
1.3 Encrypted Communications (XR500N/XR500E only)
Some installations require secure data communications. DMP offers NIST approved and UL Listed AES encrypted
communication. Use a unique passphrase to enable encrypted communications and provide a secure means for
data communications. See Network Options.
An XR500E panel communicates using AES encryption. If you currently have an XR500N panel installed, you may
purchase a separate feature key to activate encrypted communications using the Feature Upgrade process.
Encrypted communication cannot be enabled on a standard XR500 panel. For more information on the Feature
Upgrade process see Section 21 in this document.
1.4 Programmer Operation
There are 21 programming sections to choose from:
Programming Item Section in This Manual Programming Item Section in This Manual
Initialization 2Output Information 12
Communication 3 Output Groups 13
Network Options 4 Menu Display 14
Messaging Setup 5 Status List 15
Device Setup 6Printer Reports 16
Remote Options 7 PC Log Reports 17
System Reports 8Area Information 18
System Options 9 Zone Information 19
Bell Options 10 Stop 20
Output Options 11 Set Lockout Code 21
Feature Upgrade 22
To choose a section for programming, press any top row Select key when the keypad displays the name of that
section. Sections 2 through 22 contain detailed instructions for each programming step.
1.5 Programmer Lockout Codes
The panel allows you to enter the programming function without entering a lockout code using steps 1 to 4
listed in Getting Started. We recommend, however, that you install a Lockout Code to restrict programming to
only those persons your company authorizes. You can do this by using the SET LOCKOUT CODE feature in the
Programmer. The Lockout Code restricts any unauthorized panel programming.
After resetting the panel and entering the code 6653, the keypad displays PROGRAMMER. Press COMMAND
to advance through the programming sections until SET LOCKOUT CODE displays (after STOP). Press any top
row Select key. The keypad displays ENTER CODE: – . Enter a 3 to 5 digit Programmer Lockout Code and press
COMMAND. The keypad displays ENTER AGAIN followed by ENTER CODE: –. Enter the same 3 to 5 digit code a
second time and press COMMAND. The keypad displays CODE CHANGED.
Note: The panel does not accept a 5-digit Lockout Code higher than 65535.
Before accessing programmer functions enter the new code number. Write the Lockout Code number down and
keep it in a secure place with access limited to authorized persons only. Lost Lockout Codes require the panel
to be sent back to DMP for repair. You may cancel a Lockout Code by entering 00000 at the Set Lockout Code
command.
1.6 Reset Timeout
The panel has a feature that requires you to enter the Programmer within 30 minutes of resetting the panel.
After 30 minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad displays: RESET
PANEL. You must reset the panel and enter the program code then begin programming within the next 30
minutes.
If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes, the
panel terminates programming. All data entered up to that time is Not saved unless you run the Stop routine.
Note: Use the Stop routine to exit panel Programming. Ensure the keypad displays “SAVING PROGRAM” to save
all programming changes entered.
1.7 Power Up
When the XR500 Series panel is powered up after an AC power failure, any zone transitions are not recognized
for 60 seconds. Normal zone processing resumes at the end of the 60 seconds.

XR500 Series Programming Guide Digital Monitoring Products
3
IntroductIon
1.8 Keypads
DMP offers multiple keypads in a variety of styles. All DMP keypads provide the same programming capabilities.
Each keypad and its operation are shown and described in the following sections.
1.9 Special Keys
The following special keys/areas are common to all DMP keypads.
COMMAND (CMD) Key
Pressing the COMMAND key allows you to go forward through the programming menu and through each step of a
programming section. As you go through the programming, the keypad display shows any current programming
already stored in the panel memory. If no change is required for a prompt, press the COMMAND key to advance
to the next step.
The COMMAND key is also used to enter information into the panel’s memory such as phone numbers or zone
names. Press the COMMAND key after entering information.
Back Arrow (<—) Key
Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when an error
is made while entering information. Press the Back Arrow key once to erase the last character entered.
Select Keys/Areas
The top row of keys are called the Select keys on Security Command, Thinline, and Aqualite keypads or Select
Areas on Clear Touch or Graphic Touchscreen keypads. Each time you need to press a Select key, the keypad
displays the function or options above one of the keys or in the Select Area. Displaying choices above individual
Select keys or in Select Areas allows them to be used for many different applications. For example, you can
enter AM or PM when programming the automatic test time or answer YES or NO for a system option.
During programming, the Select keys/areas also allow you to change infor mation currently in panel memory by
pressing the appropriate Select key/area under or on the display. You then enter the new information using the
keypad data entry digit keys.
When there are more than four re sponse options avail able, press the COMMAND key to display the next one to
four options. Pressing the Back Arrow key allows you to review the previous four choices.
The Select keys/areas are also used for choosing a section from the pro gramming menu. Press any Select key or
touch the Select Area when the programming section name you want displays.
Note: On Wireless, Thinline and Aqualite keypads, when instructed to press the rst Select key, press the far
left Select key; the second Select key is the second from the left; third Select key is second from the right; and
the fourth Select key is the far right key. See Figure 7.
On Clear Touch or Graphic Touchscreen Keypads, when instructed to press the rst Select key, touch Select
Area 1; the second Select key touch Select Area 2; third Select key touch Select Area 3; and the fourth Select
key touch Select Area 4. See Figure 8.
Figure 3: Wireless Keypad
32-Character Display
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
Backlit Logo
and Proximity
Antenna
SMITH RESIDENCE
FRI 12: 51 PM
Figure 4: Thinline/Aqualite Keypad
32-Character Display
Armed LED
Power LED
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
JONES RESIDENCE
FRI 12:51 PM
Backlit Logo
and Proximity
Antenna
AC Power/Armed LED
Three Panic Icons
32-Character
Display with
Four Touch
Select Areas
Data Entry
Digit Keys
COMMAND KeyBack Arrow Key
Logo
Icon
ABC PRINTING
FRI 2:51 AM
Figure 5: Clear Touch Keypad
Dealer Logo Proximity Reader
Carousel
Menu
Interactive Shield
Current and Future
Weather Conditions
Figure 6: Graphic Touchscreen Keypad

Digital Monitoring Products XR500 Series Programming Guide
4
IntroductIon
1.10 Entering Alpha Characters
Some options during programming require you to enter alpha characters. To enter an alpha character, press or
touch the key that has that letter written below it. The keypad displays the number digit of the key. Next, press
the Select key/area that corresponds to the loca tion of the letter under the key. Pressing a different Select key/
area changes the letter. When another digit key is pressed, the last letter displayed is retained and the process
starts over.
1.11 Entering Non-Alpha Characters
To enter a space in an alpha entry, press the 9 digit key followed by the third Select key/area. The three
characters on the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash),
. (period), * (asterisk), and # (pound sign) using the 0 (zero) key and the four Select keys/areas from left to
right. For example, to enter a – (dash), press the 0 (zero) key and then the left Select key/area. A dash now
appears in the keypad display. The table below shows the character locations for DMP keypads.
Key Number Select Key 1 Select Key 2 Select Key 3 Select Key 4
1 A B C (
2D E F )
3 G H I !
4 J K L?
5 M N O /
6PQR &
7S T U @
8 V W X ,
9 Y Z space _
0-.* #
1.12 Keypad Displays Current Programming
Each programming prompt displayed at the keypad shows the currently selected option in the panel memory.
These options are either shown as a number, a blank, or a NO or YES. To change a number or blank to a new
number, press any top row Select key or touch any Select Area. The current option is replaced with a dash. Press
the number(s) on the keypad you want to enter as the new number for that prompt. It is not necessary to enter
numbers with leading zeros. The panel automatically right justies the number when you press the COMMAND
key.
To change a programming prompt that requires a NO or YES response, press the Select key or touch the Select
Area for the response not selected. See Figure 8.
For example, if the current prompt is selected as YES and you want to change it to NO, on Security Command,
Thinline, or Aqualite keypads press the third top row Select key. On Clear Touch or Graphic Touchscreen keypads
touch Select Area 3. The display changes to NO. Press the COMMAND key to display the next prompt.
THEN
Press the black colored top
row Select key/area.
The keypad displays the new
selection. Press CMD to advance.
YESBELL TSTNOBELL TST
YESBELL TSTNOBELL TST
Thinline,
Aqualite,
Wireless
Keypads
Clear Touch
or Graphic
Keypads
Figure 8: Changing the Current Programming Option
Figure 7: Thinline/Aqualite/Wireless Select Keys
First Letter
Second Letter
Third Letter
Special Character
(CBA
Figure 8: Clear Touch Select Areas
32-Character Display
Select Area 1
Select Area 2 Select Area 3
Select Area 4

XR500 Series Programming Guide Digital Monitoring Products
5
IntroductIon
1.13 Multiple Displays
For many programming and user options, such as Area selections, Menu Displays, and Status Lists, there are
several displays containing programming. For example, when programming Menu Displays, keypads 1 through 16
display on two separate displays. First, keypads 1 through 8 display. Press the COMMAND key to display keypads
9 through 16. This same scheme is used for areas 1 through 32.
Note: Areas not pre-programmed at installation to display at this keypad cannot be viewed.
1.14 Asterisks in Programming
Asterisks display next to a programming option that is already selected. As shown in the example, options that
are selected to display the current programming selection have an asterisk next to the number. Those that are
not selected simply display the number. In the Devices example, keypads 3, 8, 9, and 15 are not selected. In
the Areas example, areas 3, 8, 9, 15, 19, 23, 25, and 31 are not selected. In both examples the numbers with
asterisks are selected.
*1 *2 3 *4
*5 *6 *7 8 *13 *14 15 *16
9 *10 *11 *12
Devices
*29 *30 31 *32
*13 *14 15 *16
9 *10 *11 *12 25 *26 *27 *28
*1 *2 3 *4
*5 *6 *7 8 *21 *22 23 *24
*17 *18 19 *20
Areas
To select or deselect a number, simply enter the number using the digit keys on the keypad. This same scheme
is used when viewing the panel armed status and other programming and operational functions. Remember to
press the COMMAND key to display the rest of the device or area numbers.
1.15 Compliance Instructions (ANSI/UL 864)
This product incorporates eld-programmable software. In order for the product to comply with the ANSI/ UL
864 requirements, certain programming features or options must be limited to specic values as indicated
below. Refer to the XR500 Installation Guide (LT-0681) for additional information.
Program feature or option Permitted in
UL 864?
Possible settings Settings permitted in UL
864
System Reports, RESTORAL YNO, YES, DISARM YES, DISARM
System Options, PWR FAIL HRS Y0, 1 - 15 1 – 3
System Options, RETARD DELAY for
Waterow Applications
Y0, 1 - 250 1 – 90
Bell Options, FIRE TYPE YSTEADY, PULSED, TEMPORAL,
NONE
STEADY OR TEMPORAL
Status List, SYSTEM TROUBLES YAny combination of 1 – 16
addresses
Any combination 1 – 16
addresses
Status List, FIRE TYPE YAny combination of 1 – 16
addresses
Any combination 1 – 16
addresses
Zone Information, TRANSMITTER
SUPERVISION TIME for Model 1103
Y0, 3, 60, 240 3
Zone Information, RETARD for
Smoke Detectors
NNO, YES NO

Digital Monitoring Products XR500 Series Programming Guide
6
InItIalIzatIon
Initialization
NOTE: WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN AND ‘SAVING
PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE PROGRAMMING CHANGES. SEE SECTION 17.1.
2.1
INITIALIZATION
Initialization
This function allows you to clear selected parts of the panel program back to the factory
defaults in preparation for system programming. Run the initialization function on all
new installations.
CODES? NO YES
SCHEDS? NO YES
Fo
r each section of the panel program you
can initialize, a NO or YES option is provided.
Selecting YES advances you to
a confirmation prompt.
If you select YES, the panel initializes that section of
the program and advances you to the next prompt.
If you select NO, the panel advances you to the next
section prompt but does not initialize that section of
the program.
SURE?YESNO
Selecting NO adv
ances
you to the next prompt.
2.2
INIT ALL? NO YES
SURE? YES NO
Clear All Memory
NO - Leaves existing programming intact then displays Clear All Codes.
YES - Clears all memory then displays Reset Panel. Reset the panel by shorting J16 and
re-enter programming mode to continue.
2.3
CODES? NO YES
SURE? YES NO
Clear All Codes
NO - Leaves existing codes intact.
YES - Clears the user code and user prole memory and assigns user code number 99 to
the highest user position.
Note: The user name for the default user code is created using the current programmed
primary user language.
2.4
SCHEDS? NO YES
SURE? YES NO
Clear All Schedules
NO - Leaves existing schedules intact.
YES - Clears all shift, and output schedules.
2.5
EVENTS? NO YES
SURE? YES NO
Clear Display Events Memory
NO - Leaves existing event memory intact.
YES - Clears the events memory.
2.6
ZONES? NO YES
SURE? YES NO
Clear Zone Information
NO - Leaves existing zone information intact.
YES - Clears the zone information for all zones. All zones are marked * UNUSED * and
must be renamed before being able to display on any system keypad.
2.7
AREAS? NO YES
SURE? YES NO
Clear Area Information
NO - Leaves existing area information intact.
YES - Clears the area information for all areas. All areas are marked * UNUSED * and must
be renamed before being able to display on any system keypad.
2.8
OUTPUTS? NO YES
SURE? YES NO
Clear Output Information
NO - Leaves existing output information intact.
YES - Clears all programmed Output names and any output cutoff assignment.
2.9
COM/RMT? NO YES
SURE? YES NO
Clear Communication and Remote Options
NO - Leaves existing communication and remote options intact.
YES - Clears communication and remote options programming to factory defaults.
2.10
DEFAULTS NO YES
SURE? YES NO
Set to Factory Defaults
NO - Leaves existing panel programming intact.
YES - Sets the remainder of the panel programming back to the factory defaults.
Note: Sets the Programming and User language to English.

XR500 Series Programming Guide Digital Monitoring Products
7
CommuniCation
Communication
3.1
COMMUNICATION
Communication
Congure the communication options for the panel. The information you program varies
with the Communication Type you select.
3.2
ACCOUNT NO: 12345
Account Number
The Account Number is a 1 to 5 digit number used to identify which panel is sending a
message. Enter the account number sent to the SCS-1R Receiver. Messages may be sent
to a central station or via PC Log Reports to a PC. The default is 12345.
NET, CELL, 232 and DD - The range of valid account numbers for a panel is 1 to 65535.
For accounts of four digits or less, do not enter leading zeros.
CID - Choose an account number between 1 and 9999.
3.3
XMIT DELAY: 30
Transmit Delay
Enter the number of seconds (15 to 45) the panel waits before sending burglary
zones (Night, Day, or Exit) reports to the receiver. Other zone type reports are sent
immediately. Alarm bells and relay outputs are not delayed during this period. Program
Burglary Outputs for pulsed or steady, and set Abort Reports to YES if Opening and Closing
reports are not being sent. Enter 0 (zero) to disable this function. The default is 30.
If the area where the alarm occurred is disarmed during the Transmit Delay time, only an
Abort Report (S45) message is sent to the receiver. If the area where the alarm occurred
is disarmed after the alarm message is sent to the receiver but before the Bell Cutoff
time expires even if the alarm was silenced, an Alarm Cancelled (S49) message is sent.
Otherwise the alarm is sent at the end of the delay. The Alarm Cancelled report cannot
be disabled.
Note: For Commercial Burglary Installations, the combined Transmit Delay
(Abort Window) and Entry Delay must not exceed one (1) minute.
3.4 Communication Path
Up to eight communication paths may be programmed. Each path is designated as a
primary or backup communication route. Path 1 is always Primary but other paths may be
programmed as additional primary or backup.
Each primary path establishes a new path group. A path group is made up of the primary
path and its subsequent backup paths. Typical communication takes place on the primary
path with backup paths being used only when the primary path fails or when the backup
path is programmed to duplicate messages. There is no option to backup path 8.
3.5
COMM TYPE: DD
Communication Type
Species the communication method the panel uses on this path to report system events
to DMP SCS-1R Receivers or non-DMP receivers. Default is DD for Path 1, and NONE for
Path 2-8.
NONE DD NET CID
NONE - For local systems. Selecting NONE ends communication programming.
DD - Digital Dialer communications to a DMP SCS-1R Receiver.
NET - Network communication using the panel onboard network connection. The DMP
Network/Output reporting format is transmitted over a data network to the SCS-1R
Receiver.
CID - This option allows the panel to communicate to non-DMP receivers using the
Contact ID format.
CELL - This option allows communication over the cellular network using the 463G, 463C,
464-263C, 464-263H or CellComRT Cellular Communicators.
232 - This option sends serial data and can be used for radio backup or other
communication options, and uses the on-board serial port.
Select 232 when using a 462N Interface Card or DB-9 backup communications by directly
connecting to the RS-232 port on the panel. If using the on-board RS-232 port, set the
XR500 Series panel J23 jumper to R and briey reset the panel using the J16 jumper to
activate RS-232 operation. Refer to the XR500 Series Installation Guide (LT-0681).
3.6
PATH TYPE: BACKUP
Path Type
The Path Type denes if the path is Primary or Backup. Because Path 1 is Primary, this
prompt only displays for paths 2-8. Default is Backup.
Note: If the Primary Communication Type is CELL, then the backup Communication Type
can only be NET or 232.
PATH: -
CELL 232
PRIMARY BACKUP

Digital Monitoring Products XR500 Series Programming Guide
8
CommuniCation
3.7
TEST RPT: YES
Test Report
Test Report determines if test reports are sent on this path. Reports are sent according to
the programming in Test Frequency and Test Time. Default is Yes.
Select YES to allow the programmed test report to be sent on the path currently being
programmed.
Select DEFER to not send a test report if the panel communicates any message to the
receiver within the time set in Test Frequency. Select NO to not send test reports on this
path.
3.8
TEST FREQ: 1 DY
Test Frequency
Test Frequency determines the frequency of the test report. Enter a number from 1 to 60
and select DY (Day) or HR (Hour) by pressing the far right top row select key. Default is 1
Day.
3.9
TEST DAY: SUN
Test Day
Use this option to set the day of the Test Report. This prompt appears only when Test
Report is Yes, Test Frequency is Day and a multiple of seven. Press the COMMAND key to
display the rst four days of the week. Press the COMMAND key to display the last three
days. Select the day of the week to send the test report. Default is Sunday.
3.10
TEST TIME:
0:00 AM
Test Time
Use this option to select the time of day for Test Reports. Select the hour, minute and
AM/PM. Enter 0:00 AM to disable this feature. Default is 0:00 AM.
3.11
CHECKIN: NO YES
Check In
This option displays if the COMM TYPE is NET, 232 or CELL. Check-in reports are a method
of supervising the panel for communication with the receiver. For NET the default is YES.
For CELL or 232 the default is NO.
CHECKIN:
NO YES RND ADPT
Select RND (Random) for the panel to check-in at random times from 6 to 60 minutes
when all areas are disarmed. If any area is armed a check-in is sent every 6 minutes.
Select ADPT (Adaptive) for a backup path to adapt to the check-in programming from
this groups primary path if the primary path becomes unavailable. Check-in programming
includes Check-in and Fail Time.
CHECKIN:
ADP3
Select ADP3 (Adaptive 3) for a backup path to adapt using a 3 minute Check-in and
Fail Time if the primary path becomes unavailable. This option also indicates a
Communication Trouble (S10) if the cell tower is unavailable for 3 minutes.
CHECKIN MINS: 200
When YES is selected, enter the number of minutes between check-in reports, from 2 to
240 for NET and 232 or 3 to 240 for CELL, when the panel is armed or disarmed. For CELL
or 232 the default is 0. For NET the default is 200.
3.12
FAIL TIME: 240
Fail Time
This option displays if CHECKIN is set to YES. Entering a FAIL TIME allows the receiver
to miss multiple check-ins before logging that the panel is missing. The maximum fail
time is 240 minutes. For example, if CHECKIN is 10 and FAIL TIME is 30, the receiver only
indicates a Panel Not Responding after 30 minutes. The FAIL TIME must be equal to or
greater than the CHECKIN time. Default is 0 for CELL and 232. Default is 240 for NET.
3.13
ENCRYPT NO YES
Encryption (XR500E only)
Select Yes to enable encryption for the path currently being programmed. Default is NO.
3.14
RECEIVER IP
Receiver IP
This option displays only if the Communication Type is NET or CELL. Enter the Receiver
IP address where the panel sends network messages. The Receiver IP Address must be
unique and cannot be duplicated on the network. Enter all 12 digits and leave out the
periods. For example, enter IP address 192.168.0.250 as 192168000250. The periods
display automatically.
3.15
RECEIVER PORT -
Receiver Port
2001
Enter the receiver port number. Valid range is 1 to 65,535. Default is 2001.
3.16
FIRST PHONE NO.
First Telephone Number
This option displays only if the Communication Type is DD or CID.
This is the rst number the panel dials when sending reports to the receiver. Phone
numbers can have two lines of 16 characters each to equal up to 32 characters.
Enter P to program a three-second pause in the dialing sequence. The P character counts
as part of the 32 allowable characters.
NO YES DEFER
000.000.000.000

XR500 Series Programming Guide Digital Monitoring Products
9
CommuniCation
Enter R as the rst character for rotary (pulse) phone function. The R character counts as
part of the 32 allowable characters.
Call Waiting: You can place the “* 7 0 P” (Star, Seven, Zero, Pause) in the telephone
number rst position to cancel Call Waiting. For example, program NET with second line
DD and phone number *70P555-1212, and you have NET with Call Waiting cancelled on
the second line.
Caution: A call waiting cancel programmed on a non-call waiting telephone line would
prevent communication to the central station.
3.17
SECOND PHONE NO.
Second Telephone Number
The panel dials the second number when two successive tries using the rst number fail.
If the panel cannot reach the receiver after two attempts using the second number, it
returns to the rst number and makes two additional attempts. A total of ten dialing
attempts are made using the rst and second phone num bers.
Each number can be up to 32 characters in length in cluding any P or R char acters entered
for pause or rotary connections or call waiting cancel option.
Should all ten attempts fail, the panel continues to attempt sending the message using
the next programmed path. If all programmed communication paths fail, the panel clears
the communication buffer and makes one communication attempt each hour to send
a TRANSMIT FAILED (S87) report to the receiver. Access the User Menu Display Events
feature to view the report information not sent to the receiver or download the report
with DMP Remote Link™ software.
3.18
ADVANCED? NO YES
Advanced Programming
Select Yes to enter the Advanced Programming menu for the communication path
currently being programmed.
3.19 First GPRS APN
Enter the rst APN (Access Point Name). This allows an access point for cellular
communication and is used to connect to a DNS network. The APN may contain two lines
of 16 characters to equal 32 characters. Default is set to SECURECOM400.
Note: This option is not used when a 463C or 464-263C CDMA Cellular Communicator
is used for communication.
Second GPRS APN
Enter the second APN (Access Point Name). This works as a backup in case the rst APN
fails. The APN may contain two lines of 16 characters to equal 32 character Default is set
to SECURECOM400.
Note: This option is not used when a 463C or 464-263C CDMA Cellular Communicator
is used for communication.
3.20
FAIL TEST HRS: 0
Fail Test Hours
This option sets the frequency for a Backup or Adaptive path to send a test report when
the closest previous path fails within its path group.
For example, if a backup path is programmed to send a weekly test report and the
Fail Test Frequency is set to 2 hours, when the previous path fails within its group,
the backup path starts sending a test every 2 hours until the previous path restores.
If Fail Test Frequency is set to 0, test reports are sent only according to Test Report
programming. Range is 0 to 24 hours. Default is 0.
3.21
PROTOCOL: TCP
Protocol
This option displays only when Communication Type is NET.
Select TCP to communicate over the network using TCP protocol. Select UDP to
communicate using UDP protocol. Default is TCP.
3.22
RETRY SECONDS: 6
Retry Seconds
This option displays for NET or 232 Communication Types.
Enter the number of seconds (between 6 and 15) the panel should wait before retrying to
send a message to the receiver if an acknowledgment was not received. The panel retries
as many times as possible for a period of one minute before sending a network trouble
message. For example, if retry time is set to 15, the panel retries four times. The default
Retry Time is 6 seconds.
Note: If TCP is enabled, the minimum Retry Time programmed is 6 seconds.
SECURECOM400
-
FIRST GPRS APN
SECURECOM400
-
SECOND GPRS APN

Digital Monitoring Products XR500 Series Programming Guide
10
CommuniCation
3.23
SUB CODE NO
Substitution Code
This option displays when the Communication Type is NET, CELL or 232. The Panel
Substitution Code increases the level of security by helping to ensure that the panel
sending the message to the receiver has not been substituted by another panel. The
default is NO.
Select YES to send a substitution code with every message.
Select SHARED (SHR) to use the same substitution code as operating in the previous path.
3.24
232 COMM PORT: O
232 Communication Port
This option displays when Communication Type is 232.
This option sets the physical RS-232 port to the on-board connector or one of the DMP
Model 461 Interface Adaptor Card slots labeled A, B, C, D, or E. Use slot A if using a 462N
Network Interface Card with or without the 461 card.
Enter O to use the on-board connector. Set the XR500 Series panel J23 jumper to R and
briey reset the panel using the J16 jumper to activate RS-232 operation. Default is O
(On-board).
3.25
-
-
232 SETUP:
232 Setup String
This option displays when the Communication Type is 232. Enter up to two lines of 16
characters to equal up to 32 characters for the destination address that may include an
IP address. Example: If using a DMP iCOM, enter AT#UCXXX.XXX.XXX.XXX#PPPPP where X
is the IP address and P is the port number.
3.26
893A: NO YES
893A
This option displays when the Communication Type is DD or CID.
The 893A option allows reports to be sent to the receiver on a second DD line using the
893A module. Default is No.
When using this option, Test Report messages (S07 Automatic Recall Test or S88
Unrestored System Recall Test) are sent to the receiver at the frequency programmed in
Test Frequency, alternating between the rst and second phone line.
For example, a DD path with an 893A module set for daily test report frequency sends a
test report through phone line 1 one day and phone line 2 the next day.
If the 893A option is set to YES, enter up to a 3-digit prex to be dialed before the
second phone number. If no prex is entered, the second phone number is dialed as
originally entered.
3.27
ALARM SWITCH: 1
Alarm Switch
This prompt displays for DD or CID Communication Types.
Enter the number of attempts to send an alarm message before switching to the next
path. Range is from 1 to 10. All non-alarm messages are sent for 10 attempts on the
dialer before a switch is initiated. If the path immediately following this channel is not a
backup path, this option has no effect. Default is 1.
3.28
DUPLICATE ALARMS
Duplicate Alarms
This prompt displays for BACKUP paths. If Yes is selected, the current backup path
duplicates all alarms occurring on its group primary path. Default is No.
3.29
ALARM YES
Alarm Reports
This prompt displays when the Path Type is Primary. All backup paths within the group
follow the same programming for Alarm Reports. Default is Yes.
NO YES FIRE
When YES is selected, the following reports are sent to the receiver for all zone types:
• Alarm • Bypass • Reset • Restore
When FIRE is selected, the following reports are sent for Fire, Fire Verify and Supervisory
Zones:
• Alarm • Bypass • Reset • Restore
D E
O A B C
NO YES SHARED
NO YES
-
2ND LINE PREFIX: