blueclean 6950 User manual

6950 - 6970
Read carefully the present use and maintenance manual in every part before
proceeding to use. The following machine has been examined according to the
Directive Machines 2006/42, 2004/108, 2006/95 and following changes and
integrations.
Code XXXXX - XX
Hot water High
pressure washer
Original instructions
Manufactured and distributed by : Annovi Reverberi S.p.A.
Via M.L. King 3
41122 Modena (Italy)
www.annovireverberi.it

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 2
SECTION INDEX PAGE
1 GENERAL INSTRUCTIONS 2
2 MACHINE IDENTIFICATION 3
3 TECHNICAL FEATURES 4
4 MACHINE DIMENSIONS 4
5 MAIN PARTS 5
6 SAFETY REGULATIONS 6
7 MACHINE INSTALLATION 7
8 MACHINE START UP 8
9 REGULATION OF THE OPERATING PRESSURE 9
10 MACHINE SHELTER 9
11 STANDARD EQUIPMENT 9
12 OPTIONALS 9
13 DETERGENTS 9
14 ELECTRIC DIAGRAM 10
15 LABELS 11
16 MAINTENANCE 12-13
17 COOLING COIL INTERNAL CLEANING 13
18 MACHINE DEMOLITION 13
19 WARRANTY 14
20 WARRANTY CERTIFICATE 15
21 DRAWBACKS, CAUSES AND SOLUTIONS 16
22 DECLARATION OF CONFORMITY 17
1. GENERAL INSTRUCTIONS
Congratulation for your choice on the purchase of your new cleaner; it means that you have keep technical
knowledge and good taste for the nice design. Technological innovation, high preformances and strenght
are the main features of the machine 6950/6970.
This manual is an integral part of the washer and it must be found easily by the personnel responsible about
the maintenance and by the user. The users, the qualified individuals must know the contents of this ma-
nual. In case of troubles, doubts as to understand this manual, please contact the Company
ANNOVI REVERBERI - Via Aldo Moro, 40/42 - 41030 Bomporto (MO) Italy, suppor[email protected].
Descriptions and images contained in this manual are not binding, therefore, the Company, reserves the
right to make chenges at any time and without prior notice.
IMPORTANT !
For a proper and safe operation of the machine, read this manual carefully before
connecting the machine o the power supply and bifore setting it a work.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 3
The machine has been designed to clean or wash, with hot or cold water, objects or surfaces which can
stand the mechanical treatment of the water jet under high pressure and by the action of the chemicals
products (detergents). Before starting, be sure that it is supplied with the relevant identification rating plate;
otherwise you must contact your dealer immediately and don’t use the machine (see fig. 1). Never leave an
operating cleaner unattended in the work place. After a working day we suggest to place the machine in a
dry place and protected from the bad whether conditions.
The machine must be used only for the purposes for which it has been designed.
Never use the machine if the safety conditions are uncertain. In case of demolition, please follow the law in
force in your Country.
2. MACHINE IDENTIFICATION
Fig. 1 below indicates where the identification plate is fixed.
A = WORKING PRESSURE
B = MAX PRESSURE
C = FLOW RATE
D = WATER MAX TEMPERATURE - INPUT
E = BURNER POWER
F = ABSORBED POWER
G = VOLT/HZ
H = FUEL TYPE
I = FUEL TANK CAPACITY
L = SERIAL NUMBER
M = PROTECTION DEGREE
N = NOISE VALUE
O = PRODUCT CODE
The data on the plate must not be erased for any reason.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 4
3.TECHNICAL FEATURES
MODEL 6950 6970
Pressure BAR 150 200
P.S.I. 2200 2900
Power KW (OUTPUT) 4 5,5
KW (INPUT) 5 7,4
RPM 1450 1450
Voltage V/Hz 220-60Hz 3 ~ 220-60Hz 3 ~
Max capacity L/H 600 900
Gal/h 159 238
Temperature °Δ T °C 60 60
Fuel tank Liters 14 14
Detergent tank Liters 6 6
Dimensions H 800 800
W 590 590
L 880 880
Lpa (EN 60704-1) Db (A) 80,7 82
Lwa (EN 60704-1) Db (A) 89 90
Machine vibrations M/s21,45 1,45
Weight kg 93 97
4. MACHINE DIMENSIONS

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 5
5. MAIN PARTS
1 ELECTRIC CABLE 7 FUEL FILTER
2 ELECTRIC MOTOR 8 HIGH PRESSURE PUMP
3 BOILER 9 PRESSURE VALVE
4 ELECTRIC SYSTEM 10 COMBUSTION HEAD
5DETERGENT TANK 11 PRESSURE SWITCH
6FUEL TANK

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 6
6. SAFETY REGULATIONS
• Make sure that the machine is constantly supplied with water. Dry working would cause serious damages
to the machine seal system.
• Electrical connections must be carried out by skilled/trained personnel only.
• Never pull the power cord to disconnect the plug nor pull the hose to move the machine.
• Don’t leave the machine in a low temperature place and protect it from frost and general bad weather
conditions.
• Avoid vehicles transit on the high pressure hose.
• While the machine is running do not cover it and avoid placing it where there’s low air supply.
• If you are working indoors, it’s compulsory to install a fan to discharge the exhaust gases outside.
• The fan terminal must not be obstructed. Don’t leave the lance or any other object near the exhaust outlet.
• The nature of the gases as well as the high temperature are to be considered very dangerous, the operator
must thus be adequately informed in order to avoid being scalded.
• Don’t leave the machine outside when it rains or when the weather conditions are bad. The operators must
wear protection clothes while using the machine.
• Do not leave the machine for more than 15 minutes working with the gun closed, the water temperature
would increase rapidly causing serious damages to the seal system.
• Each time the machine has to be switched o blow o the hose residual pressure by using the gun.
• Don’t put the hands in front of the lance.
• Do not use dierent fuels other than the ones recommended by the manufacturer.
WARNING !
• Don’t carry out any operation on the machine before having unplugged it.
• Don’t carry out any unwary operation on the electric cable and make sure thesame is not damaged.
• Never direct the high pressure water jet towards people, animals, electrical installations or the machine
itself.
• Use always only clean water. Dirty water and chemical corrosive products are harmful for the machine.
• The machine is equipped with idle wheels; it it thus recommendable to avoid placing the machine on ram-
ps or slanted floors. Do not tilt the machine by more than 20 °C (with full tank).
• It is forbidden to use plug extensions if the work enviroment is subject to water/humidity presence which
could cut the isolating conditions of the system. Always check the isolation of the electric cable as well as
the equipment’s integrity.
• In case an extension is required, be sure that plugs and sockets have a protection type IP65 and that the
power cord complies with the table reported here below.
VOLTAGE V EXTENSION LENGTH CABLE SECTION
380 - 415 0 mt UP TO 25 mt 4x2,5 mm2
380 - 415 25 mt UP TO 50 mt 4x4 mm2

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 7
7. MACHINE INSTALLATION
The machine you are about to use will give you the best
performances if you install itself following our instructions.
Before setting the machine at work, make sure that the ma-
chine lies perfectly on a horizontal surface. Connect the high
pressure hose A to the gun B and with the other side of the
cable to
the intake fitting, fixing tightly the fastening nut C (see fig.
4). Connect the lance B1 to the gun B.
Connect the water supply hose D to the infeed fitting E (see
fig. 5). It is recommended to use a reinforced hose having an
inner diameter of at least 10 mm. The water intake must be
of at least 15 l/min and have a max inlet temperature of 60
°C.
Fill the fuel tank F (see fig. 6) with gasoil (Diesel). Fill the de-
tergent tank G (see fig. 6) with a biodegradable product.
Make sure that the electrical tension and amperage are su-
itable for the machine. The cleaner must be connected to a
suitable feeding point equipped with an efficient contact to
earth and controlled by an overload cut out switch.
The detergent is applied by opening the intake device of the
lance (on the position - see figure) and then operating with
the gun lever.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 8
8. MACHINE START-UP
After having installed the machine, in order to operate it, open the water supply faucet H.
The control panel has been designed to run the operations easily. The knob A has three main functions:
Pos.1 OFF indicates that the
machine is turned o. Pos.2 The second position indicates that the motor pump is on. Pos.3 The third position ON indi- cates that the boiler is on.
Turn the thermostat knob B. This allows to control the temperature of the ‘water bringing it to the desired
value, set by means of a scale of values ranging from 0 to 150 ° C.
The pressure gauge C indicates the pressure in the pump
IMPORTANT! Make sure the pressure never exceeds the pressure indicated on the pump plate.
The hydraulic system is equipped with a safety valve that works whenever the pressures is higher than
the calibration.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 9
9. REGULATION OF THE OPERATING PRESSURE
On this machine It is possible to
regulate the operating pressure.
Move to near the machine cover,
in the valve access window, see
fig. 8. Grip the valve knob, if provi-
ded, or use a wrench, if provided,
in pos. 1, and rotating clockwise
(fig. 9 pos. 1) the pressure increa-
ses; rotating the knob (fig. 9 pos.
2) anti-clockwise the pressure
decreases.
IMPORTANT! Make sure that the operating pressure never exceeds the pressure indicated on
the pump’s plate.
10. MACHINE SHELTER
Once finished working after having discharged the remaining pressure in the hose and after having inserted
the safety catch on the gun picture 4 pos. 1 and 2, wind-up the electrical hose and the high pressure hose in
order not to damage them. Place the high pressure cleaner in a sheltered away from the possibility of non
authorized people to use it.
11. STANDARD EQUIPMENT
We suggest to check the cleaner when it is delivered. It must be complete in all the parts and be supplied
with: a thermal lance, a 10 m high pressure hose and a nozzle suitable for the model you have purchased.
12. OPTIONALS
ANNOVI REVERBERI supplies a rotary jet nozzle on request which allows to remove the hardest dirt from any
surfaces you want to clean and wash.
13. DETERGENTS
It is advisable to use detergents with liquid base and not with dusts. Use biodegradabile detergents, obser-
vating the relative regulations in force.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 10
14. ELECTRIC WIRING DIAGRAM
CT THERMAL PROTECTOR P1 PRESSURE SWITCH 40 BAR
EV FUEL ELECTROVALVE P2 PRESSURE SWITCH 15 BAR
FU1 FUSE PROTECTION SE ELECTRONIC PRINT BOARD
IG GENERAL ON-OFF SWITCH TM THERMOSTAT
MB BURNER MOTOR TR BURNER TRASFORMER
MP PUMP MOTOR MB BURNER MOTOR

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 11
15. LABELS
The machine comes with a safety warning signs, it is also recommended to comply with all applicable safety
regulations issued by the country of installation of the machine.
Below is a table shows the types of adhesives used and their meaning:
1 Warning! Gases at high temperature - outlet 5 Water feeeding
2 Warning! Do not direct the high pressure jet towards people, animals or objects 6 Fuel tank
3 Lance delivery 7 Detergent tank
WARNING!
Make sure that the stickers/labels are present on the machine and that they are readable; if they are missing
or erased, please attach or replace them. Ask for them from the licensed dealers.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 12
16. MAINTENANCE
WARNING !
• All the xing and maintenance operations must be carried out by authorized personnel.
• All maintenance operations must be carried out keeping the machine on an even oor. The machine must
be disconnected from the main power and from the water supply.
• A correct use and maintenance are necessary to guarantee the machine’s reliability and it’s best perfor-
mances.
• In order to ensure regular and constant performances it is recommended to use original spare parts only.
• The machine you have bought has undergone a factory test which ensures correct running at standard
conditions.
• Beware! In case the cleaner has been kept inoperative for a long time, run some water through the coil
until it comes out before using it again. Besides preliminary controls, the cleaner needs constant checks that
are to be carried out according to following time schedules:
DAILY
Check the oil level of the pump, after having removed
the cover. Unscrew the cap fig.7 pos. A, check the level
which should be between the max and the min., fig. 7
pos. B and if necessary add some. After having che-
cked the level place back the cap and the cover. It is
recommended to use oil type SAE 15W/40. The first oil
top up should be carried out after one week work.
Check the working condition of the feeding hose and the extension cable.
EVERY 2 WEEKS AND AFTER 50 HOURS WORKING SHIFT
Clean water filter, which is located in the tank (fig. 8).
Remove the cover of the machine, remove the cover
of the tank fig.8. pos. A, unscrew the plastic filter pos.
B. Blow with a jet of air and then replace the lid and
screw it again replace both the cover of the tank and
the machine.
Clean the fuel filter (fig.10).
Remove the cover of the machine, unscrew the tran-
sparent glass, see fig.10 pos.A extract by pulling down
on pos.B the plastic mesh filter, blow it with gentle
stream of air and refit, make sure that the glass is
tight.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 13
EVERY MONTH OR AFTER 100 HOURS OF WORK
Clean the combustion head and check the electrodes. Remove the cover, unscrew the three screws fig. 11
pos. A, extract the combustion head group pos. B. Clean with an air jet the head and check the glow plug
pos. C. The distance between the electrodes must be of 3 mm. If the distance must be adjusted, unscrew
glow plug screw pos. E, remove the glow plug, adjust the distance to acheive the 3 mm distance. Reassem-
ble the glow plug while checking it is fixed correctly. Place the combustion back in place using the three
screws pos. A.
This maintenance operation must be carried our by skilled personnel.
EVERY MONTH O AFTER 200 HOURS OF WORK
Carry out the first topping up of the pump oil. Clean
the combustion pump filter. Remove the cover.
Near the pump picture 13 pos. A on the side of the
filter symbol, extract the plastic filter using a 4 mm
socked head screw. Clean the filter with a light air jet
an place it place back. If necessary replace it.
This maintenance operation must be carried our
by skilled personnel.
17. COOLING COIL INTERNAL CLEANING
Contact an Authorized Service Centre.
18. MACHINE DEMOLITION
If you want to junk your machine, please comply to the laws in force in your Country. The machine is ma-
nufactured with parts containing recyclable metals and plastics. The oil found inside the pump is highly
dangerous and pollutant and must not be wasted in the environment or poured into civic drains. For further
informations, please contact your local commitee for exhaust oil drainage.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 14
19. WARRANTY
The duration of the warranty is in accordance with the relevant legislation in the country where the product
is sold (unless otherwise stated by the producer).
The warranty covers materials, construction and conformity defects during the warranty period, during
which time the manufacturer will replace defective parts and repair or replace the product if excessively
worn in normal use.
The warranty does not cover components subject to normal wear (valves, pistons, water gasket, oil gasket,
springs, O-rings, accessories such as hoses, guns, brushes, wheels, etc.).
The warranty does not cover defects caused by or resulting from:
- incorrect use, abuse or neglect,
- trade, professional or hire use,
- failure to service and maintain the unit as specified in the user’s manual,
- unauthorised repairs,
- use of non-original accessories/spare parts,
- damage incurred during shipping or due to foreign objects or substances and accidental damage,
- warehousing and stock keeping problems.
To register the warranty, the customer must provide proof of purchase.

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 15
20. WARRANTY CERTIFICATE

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 16
21. DRAWBACKS, CAUSES AND SOLUTIONS
PROBLEM POSSIBLE CAUSES SOLUTION
WATER DOES NOT COME OUT Dirty water filter Clean or replace
Blocked infeed valves Check
Clogged lance nozzle Clean
INSUFFICIENT OR IRREGULAR
PRESSURE
The detergent valve is open and
takes in air
Check
Insufficient water supply Check the capacity
The pump intakes air Check
Worn out valve Replace
Worn out/not suitable nozzle
Replace
Worn out gaskets Replace
Exceeding water temperature Check
Encrusted coil Scale
THE BURNER DOES NOT TURN ON Excessive air intake Check
Dirty fuel filter Replace
Dirty fuel pump filter Clean or replace
Dirty burner nozzle Replace
Faulty thermostat Replace
Broken/blocked electrovalve Replace
Insufficient electrodes spark Replace
Defected flowmeter and/or pres-
sure switch
Replace
Worn out motor pump joint Replace
Absent/insufficient voltage Check
NOISY MACHINE Air intake Check the intake pumps
Worn out/dirty/blocked valves Check the intake pumps
Exceeding water temperature Check the intake pumps
WATER PRESENCE IN THE OIL Worn out water/oil rings Replace
High percentage of humidity in
the air
Check
OIL LEAKAGE FROM THE HEAD Worn out O-rings of the seal
system
Replace
MOTOR DOES NOT START WHEN
PRESSING THE SWITCH
The plug is not working due to
overheating
Check the plug, the cable and the
ON/OFF switch
SUDDEN MOTOR STOP The thermal protection is not wor-
king due to overheating
Make sure that the tension is
suitable

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 17
22. DECLARATION OF CONFORMITY
We Annovi Reverberi S.p.A., Bomporto (Mo),Italy declare that the following AR Blue Clean Machine(s):
Designation of Machine High Pressure Washer
Model No / Type 6950 6970
Input power 5 kW 7,4 kW
Conforms to the following European Directives:
2006/42/EC, 2006/95/EC, 2002/95/EC, 2002/96/EC, 2004/108/EC, 2000/14/EC
And are manufactured in accordance to the following standards or standardised documents: EN 60335-1; EN
60335-2-79; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
Name and address of the person in charge to give the technical file:
Stefano Reverberi / AR Managing Director
Via M. L. King, 3 - 41122 Modena, Italy
The conformity assessment procedure required by Directive 2000/14/EC was in accordance with annex V
6950 6970
Measured Sound
Power Level: 88 dB (A) 89 dB (A)
Guaranteed Sound
Power Level: 89 dB (A) 90 dB (A)
Date : 25.10.2011
MODENA (I)
Stefano Reverberi Managing Director

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 18

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 19

AR BLUE CLEAN 6950 - 6970
USE AND MAINTENANCE HANDBOOK Page 20
VIA ALDO MORO, 40/42
41030 BOMPORTO (MO)
ITALY
[e-mail]