Bluetti EP600 User manual

EP600 Quick Guide
1. Overview 2. Installation
2.2 Installation requirements 2. 3 Wall mounting
EP600 1 PV input 1 5 LED Indicator 9 Waterproof and
ventilate valve 13 USB Port
2PV input 2 6 Signal Port 1 10 COM
Communicate Port 14 Load Port
3 DC ON/OFF 7 Signal Port 2 11 CT Input Port 15 Grid Port
4Battery
Negative
8Battery
Positive
12 DRMs Port 16 Ground
3. Connecting cables
3.1 overview
3.2 Connect the communication cable
B500 1 Negative output cable port
(Upper)
6 Positive output cable
port (upper)
11 Ground wire
port(Upper)
2 Signal connection cable port
(Upper)
7 Inverter signal cable
port
12 Ground wire
port(Bottom)
3 Signal cable port (Bottom) 8Waterproof and
breathable valve
13 Waterproof and
breathable valve
4 Negative output cable port
(Bottom)
9 Positive output cable port (bottom)
5
Manual mechanical switch
10
ON/OFF Switch
2. Installation
2.1 overview
NOTE: The Meter is only used for the situation of installed three phase solar PV inverters, it is provided By BLUETTI and it
is free.
NOTES:
1. This document is for quick guidance installation only. For details, please refer to the installation and User Manual.
2. Machine damage caused by failure to follow the content is not covered by the warranty.
Note:Make sure the router used for EP600 applies to WiFi of
IEEE 802.11 b/g/n, 2.4GHz, please turn off the 5G option

3.3 Connect the Ground Cable 3.5 Connect the Batteries and EP600 3.6 Connect PV cable 3.7 Connection CT
Port Define Cable pec.
PV1+：To solar
panel positive
PV1-：To solar
panel negative
PV1 PE：PV1 to
solar panel ground
Conductor
cross-
sectional
area
2.5mm2～
4mm2
PV2+：To solar
panel positive
PV2-：To solar
panel negative
PV2 PE：PV2 to
solar panel ground
NOTES:
1.Make sure the arrow inside the CT points to the grid.
2.Pay attention to the phase sequence when connect the
CT: L1 to R, L2 to S, L3 to T.
3.The CT connect to the EP600 must be installed onto the
L1/L2/L3 cables of the residential main circuit breaker.
3.4 Connect the GRID and BACKUP Cable
3.7 Connection Transfer Switch
Transfer switch is necessary for building a partial residential
backup system.
NOTES:
1.The neutral cable from the BACKUP interface of EP600
cannot be connected to the neutral cable of the public grid.
2.Connect the L1/L2/L3/N wires from EP600 BACKUP to the
pin 2(L1), pin 6(L2), pin 10(L3), pin 14(N) of transfer switch;
3.Connect the L1/L2/L3/N wires from public grid to the pin
4(L1), pin 8(L2), pin 12(L3), pin 16(N) of transfer switch;
4. Move away the wires of the circuit breaker connected to
essential appliances, then connect pin1(L1), pin 5(L2),
pin9(L3), pin 13(N) of transfer switch.
NOTE: Please check the solar PV open circuit voltage
, it must be less than 500V.
NOTE:It is forbidden to connect the grid cable to
the BACKUP interface of EP600.

3.8 Electrical connection modes 1: DC coupling 4. Power on
Step1: Switch on the DC circuit breaker on each B500
battery pack.
Step2: Press and hold the power button of any battery pack
for 3 seconds and the green indicator on the button lights
up.
Step3: Wait for 40 seconds until the green indicator of the
inverter is always on.
Step4: When connecting to the sloar panel ,please switch on
the DC circuit breakers on EP600.
Step5: Switch on the AC circuit breakers connected to the
EP600 grid port.
Step6: Power on the system via the BLUETTI app. For
details, please refer to Setting section on App Manual.
Step7: Check the voltage of BACKUP.
Step8: Switch on the AC circuit breakers connected to the
EP600 load port.
END,Then you can check the EP600 system status through
the app.
3.9 Electrical connection modes 2: AC coupling
5. Service and contact
After-sales address in EU ：Lise-Meitner-Strasse 14, 28816
Stuhr, Germany
NOTE:
The Meter is only applicable to the case where the PV grid-tied inverters have been
installed.
1) Connect the cables of UA UB UC UN to the L1/L2/L3/N of the PV inverter,
2) Connect the cables of the CT to the Meter and tied to the wires of L1/L2/L3/N of the PV
inverter.
3) Please connect the 485-A red wire to pin 21,485-B black wire to pin 22.