BMB Technology Zada User manual

smart water technology
BMB ULTRAFILTRATION SERIES
INSTALLATION GUIDE
Models:
BMB ZADA ULTRAFILTRATION SYSTEM
BMB ZADA PRO ULTRAFILTRATION SYSTEM
BMB NANO ULTRAFILTRATION SYSTEM

2
TABLE OF CONTENTS
PACKAGE CONTENTS 3
PREPARING THE FITTINGS 4
REMOVING THE BLANK FITTINGS 4
INSERTING THE ELBOW CONNECTORS 4
FEED WATER CONNECTION 5
TAP CONNECTION 6
MOUNTING THE SYSTEM 7
REPLACING THE FILTERS 8
BMB ZADA / BMB ZADA PRO 8
BMB NANO ULTRAFILTRATON SYSTEM 8
IMPORTANT NOTE FOR NEW INSTALLATION AND REPLACEMENT FILTERS* 9
NOTES 9

3
PACKAGE CONTENTS
Tap Tubing Feed Water Valve Tubing Elbow Connections
BMB Zada BMB Zada Pro
System Overview Diagram with Tap
BMB Nano UF

4
PREPARING THE FITTINGS
REMOVING THE BLANK FITTINGS
INSERTING THE ELBOW CONNECTORS
Both the Zada and Zada Pro have blank fittings (please skip this step with the BMB Nano
UF) applied by default, this is to protect the inlet and outlet of the filtration systems during
transport. First of all, let’s remove the blank fittings.
To remove the blank fittings, simply push the collet (aka collar) in towards the fitting with
whilst pulling the blank fitting away from the main fitting.
Now to insert elbow connections, simply push the straight side (3/4”) to the inlet and outlet
plugs ensuring it’s inserted until it doesn’t go in anymore.
Please ensure you do this for both sides.

5
FEED WATER CONNECTION
The purpose of the feed water connection is to feed the system with water to be purified
by tapping into the coldwater supply.
Before you start, please ensure you have turned off the main water supply and always
ensure there is a bucket or bowl and dry cloth for unforeseen circumstances.
Please see figure below for instructions on how to make the feed water connection.
1. Once you have located the cold-water valve, turn the water supply off then remove
the flexible hose.
2. Attach the Tubing Feed Water Valve included within the installation kit to the
cold-water valve (please ensure you use the PTFE tape provided around the thread),
then attach the flexible hose to the Tubing Feed Water Valve.
3. Finally, fully insert the 1/4” tube from the filtration system to the Tubing Feed Water
Valve.

6
TAP CONNECTION
First of all, a proper location to mount the tap needs to be selected, paying close attention
to the placement of the tap stem under the counter.
Ensure you use the correct type of drill bit for your counter type
Hammer Drill Bit: Cement, Tile, Granite, Marble & Marmoreal
HSS Drill Bit: Steel, Wood, Chrome, Metal & Aluminium
1. Drill initial hole using a 5mm drill bit then use a 12mm drill bit to enlarge the hole to
the proper diameter.
2. Place the tap through the drilled hole and mount it to the sink per the images above.
3. Install the Flange, Rubber Gasket, Locking Washer.
4. Tighten the tap with the Faucet Nut using a Spanner.
5. Insert the Tubing Pin to the white tube provided and connect to the taps stem using
the Tubing Ring & Nut.
6. Connect the other end of the tubing to the “Clean Water” port on the system and
you’re good to go!
Locking Washer
Tubing Nut
Tubing Ring
Faucet
Nut Rubber Gasket
Flange
Tubing Pin

7
MOUNTING THE SYSTEM
Mounting the BMB Zada, Zada Pro and Nano UF is really simple and all you need is 2 x wall
plugs and 2 x screws (not supplied). Please ensure that there is at least 10cm empty below
the bottom of the filter system to ensure you have enough space to pull the filter(s) down
when the filter is due to be replaced.
Simply mark the cupboard for the two holes for your system. You’re satisfied with the
height of the mount location, simply drill the holes, insert wall plugs followed by the screws.
Simply place your system on to the screws. You can tighten the screws for the Zada / Zada
Pro. If the Nano UF is loose, simply tighten the screws a little more until the system is not
hanging loose.

8
REPLACING THE FILTERS
BMB ZADA / ZADA PRO
Please make sure the Tubing Feed Water Valve is turned off to ensure water flow is stopped
before removing the filter. Have a towel handy for excess water dispensing as you’re
removing the filters.
Replacing the filters have never been so simple. By default, the filters will be locked; simply
unlock the filter then twist and pull it down to remove. Please follow guided diagrams
below.
To unlock the filter, turn the nozzle
anti-clockwise until you hear a click.
Once unlocked, simply turn the filter
clockwise / towards the left (follow the arrow on
the bottom of the filter) and you can pull it down
once completely released.
To install the new filter, simply push up and turn back into place then lock the filter by
turning the nozzle clockwise until you hear the click once more. You will receive an
automated email when the filters are due replacement. The email will consist of link(s) to
the replacement filter(s) if you have not purchased them yet.
BMB NANO ULTRAFILTRATION SYSTEM
If you have purchased the Nano UF, then it’s even easier to replace the filters with its
self-lock technology. Simply hold a twist to remove and repeat the process to attach the
new filters.
2
1

9
Important Note for New Installation and
Replacement Filters
You may get a metallic or an initial unpleasant taste / odour, this is due to the
nano-particles within the filtration system.
Simply flush the system by letting the water run for 15 minutes, then again after an hour or
two later.
Repeat this process a few times and the taste will improve as the filters would have been
flushed. Also, do bear in mind that the taste will require getting used to, as the fresh filtered
water will not taste like bottled water nor hard tap water.
Notes: