BN Products BNMS-100B User manual

BNMS100B Assembly Instructions.indd
BN Products-USA, LLC.
3450 Sabin Brown Road
Wickenburg, AZ 85390
[phone]
[email protected]
Assembly InstructionsAssembly Instructions
BNMS-100B Mixing Station
1. Check the package you received to ensure all parts are in-
cluded. If any parts are missing do not return this product to the
store but contact BN Customer Service at 1-800-992-3833.
2. To attach the Casters (#1) turn the
Lower Fame Assembly (#5) upside down
on a level surface. The two locking cast-
ers need to be installed in the back of the
frame that is near the Foot Lock Lever
(#4). Use a 3/4” open end wrench and a
3/4” socket to install the casters. Install
a wheel bolt and washer up through
the Lower Frame (#5) and through the
Caster and attach with a Lock Nut (#3)
on each wheel.
3. Place the Back Plate (#22) inside the Bucket Frame (#21) with the threaded
stud sticking out of the bottom hole and loosely start the Wing Nut (#27).
Thread the Lock Handle (#26) through the Bucket Frame and into the Back
Plate but leave loose. See Diagram B.
4. With the Back Plate (#22) very loose slide the Extension Frame (#8) into
the Bucket Frame and lock into place about 4 inches from the bottom.
5. Slide the Extension Tube (#10) with swivel into the Extension Frame and lock
in place with the Pin (#9). See Diagra C.
6. Attach the two Knob Bolts (#13) to the Swivel Assembly.
7. Install the battery in the Timer and attach it to the back bracket.
8. The electric mixer can now be installed and the Swivel adjusted with the
Bottom Knob (#18).
Note: When attaching an electric mixer, the paddle will need to
be pushed up through the Swivel and threaded into the mixer.
Diagram A
Diagram B
Diagram C

BNMS100B Assembly Instructions.indd
Assembly InstructionsAssembly Instructions
No. DESCRIPTION PART No.
1 CASTER BNMS-100B NON LOCKING 101113
2 WASHER BNMS-100B 101114
3 LOCK NUT BNMS-100B 101115
4 PIN BNMS-100B 101116
5 STAND BNMS-100B 101117
6 SLEEVE BNMS-100B 101118
7 ROTATING SHAFT BNMS-100B 101119
8 EXTENSION FRAME BNMS-100B 101120
9 PIN BNMS-100B 101121
10 EXTENSION TUBE BNMS-100B 101122
11 HOOP PIN BNMS-100B 101123
12 BUCKET BNMS-100B 101124
13 BAKELITE BOLT M8 BNMS-100B 101125
14 SWING AXLE ASM BNMS-100B 101126
No. DESCRIPTION PART No.
15 UPPER BALL BNMS-100B 101127
16 LOWER BALL BNMS-100B 101128
17 MOUNTING PLATE BNMS-100B 101129
18 BAKELITE BOLT M6 BNMS-100B 101130
19 HEX BOLT M8 X 30 BNMS-100B 101131
20 HEX BOLT M8 X 15 BNMS-100B 101132
21 FRAME BNMS-100B 101133
22 BACK PLATE BNMS-100B 101134
23 HOOK BNMS-100B 101135
24 RND HD BOLT M6 X 12 BNMS-100B 101136
25 PROTECTION BOARD BNMS-100B 101137
26 LOCK BOLT BNMS-100B 101138
27 NUT M6 BNMS-100B 101139
28 CASTER BNMS-100B LOCKING 101113L