Bobot WIN SPIDER User manual

USER MANUAL
BOBOT WIN SPIDER
Robot Window Cleaner
Please read this instructions carefully before using the product
and keep it in a safe place.

Thank you for choosing to buy
BOBOT WIN SPIDER
Assembling your
Machine
1 2
Quick Start
1
2
Attach Cleaning Pad
Fix the Safety Rope
Warning: Attach the cleaning
pad to robot properly, the
pad should not cover edge
sensors, otherwise it would lead
dropping.
Attach the cleaning pad to BOBOT WIN SPIDER buttom properly, the pad should
not cover driving treads or edge sensors.
Plug in the safety lock into hole,
turn it in clockwise till indicator
light changed to Green.
Tie the end of safety rope to
is stable and won't drop.
Spray water 5-8 times to the
yellow side of cloth.
Don't spray water on the body
or bottom of robot, only could
spray on the cloth.
NOTE: Please start to use the
robot ONLY when the safety lock
indicator light is in Green.
while using could lead to
dropping.
Power Cord
Indicator Light
Red: Alarm
Blue: Normal
Orange: Charing
Green: Fully Charged
Bottom Status
Indicator Light Velcro
Photoelectric Edge Sensor Anti Stuck Ring
Driving Tread
Fan
Red: Alarm
Blue: Normal
Safety Lock Hole
Ultrasonic Edge Sensor
There are 4 sensors：
2 concave Ultrasonic edge sensor
2 convex Photoelectric edge sensor
These 4 sensors could guaranty non dropping when the machine meet big crevice, which is better
than normal 4 convex sensors in the market.

34
3Connect to Power Supply
Plug in BOBOT WIN SPIDER
4
5
4
Press the Power Button
Walking belt auto clean method
Press power button for 2
secondes to turn on your
BOBOT WIN SPIDER
Caution: Before starting, make sure the edge of
BOBOT WIN SPIDER is 8cm or more away
from window frames or corners.
A. B. C.Place your BOBOT WIN SPIDER
on glass, press again the power
button to start.
You can also start it from your
remote control "START" button.
Every time before and after using, the walking belt should be cleaned to prevent
dirt and dust from sticking on, to enhance the performance of machine. Steps to
clean walking belt as follows:
(1) Turns on the machine (press power button).
(2) Put the machine in the reverse direction (belt up) on the workbench.
(3) Press a sensor (any of 4 corners) for about 8 seconds, the machine
automatically enters belt cleaning mode, the drive wheels on both sides
rotate and the vacuum motor stops.
(4) Use a clean cloth, slightly wipe on the belt surface.
(5) After cleaning the belt, press switch button to shut off.
Do not spray water on the glass,
the wet glass will make the
driving tread slip!
The window cleaner must be
connected to the power supply
and safety rope.
while using could lead to
dropping.

5
IMPORTANT SAFETY
INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL
INSTRUCTIONS AND CAUTIONARY MARKINGS
IN THE USER MANUAL AND ON THE APPLIANCE.
The appliance is not to be used by children. Persons with
reduced physical, sensory or mental opbiities, or lack of
experience and knowledge may only use this appliance if they
are supervised or have been given instruction about how to use
it safely and understand what risks are involved. Children should
be supervised to ensure they do not play with the robot.
The appliance is for window cleaning with Frames
(Frameless glass/window cleaning is not applicable).
Users should judge and use it safely on proper
operation sites, and be responsible for all possible
consequences.
Application of Power Adatper and Batterys
Use only the power adapter supplied with this device.
Use of other type of power adapter will result in
malfunction and/or danger.
Please use the proper electric outlet and make sure no
heavy objects are placed on the poweradapter or power
cord.
Allow adequate ventilation around the adapter when
using it to operate the device. Do not cover the power
adapter with objects that will reduce cooling.
Do not use the adapter in a high moisture environment.
Never handle the adapter with wet hands.
Connect the adapter to a proper power source. The
voltage requirements are found on the adapter.
Do not use broken adapter, power cord or plug. The plug
must be removed from the receptacle before cleaning
or maintaining the Appliance. Do not unplug the Power
Adapter by pulling on the power cord.
Do not attempt to service the adapter. There are no
service parts inside. Replace the whole unit if it is
damaged or exposed to high moisture. Consult your
Mamibbot dealer for help and maintenance.
The battery used in this device may present a risk of
short contact, heat above 60C (140 F ), or incinerate.
If you have to dispose of this old equipment, please take
it to the local recycling center for recycling electrical and
electronic parts.
Retain the safety and operating instructions for future
reference.
Follow all operating and use instructions.
Do not expose your device to rain or excess humidity,
and keep it away from liquids (such as beverages,
faucets, and so on).
Avoid exposing your device to direct sunlight or intense
light source, and keep it away from heat source (such as
radiators, space heaters, stoves, and so on).
Do not place the device in the vicinity of strong magnetic
Keep the device and accessories away from children.
Product operating temperature: 0c ~40C (32F~104F).
Don't use it cracked glass or clean other surface with
power.
The Back-Up Battery must be replaced by the
manufacturer or its service agent in order to avoid a
hazard. The Back-Up Battery must be removed and
discarded according to local laws and regulations before
disposal of the Appliance. Please dispose of used
batteries according to local laws and regulations.
The Appliance must be disconnected from the
receptacle before removing the battery for disposal of
the Appliance.
The Appliance must be used in accordance with
the directions in this Instruction Manual. Product
manufacturer cannot be held liable or responsible for
any damages or injuries caused by improper use.
cleaning or maintenance work.
Never pull the power plug out of the socket by the power
cold; instedd, pull it out by the power plug itself.
Never perform repairs on your device yourself. Repairs
to ecric devices may only be carried out by authorized
customer service center.
Do not insert any pointed objects into the electric
contacts.
Do not change the contacts.
Do not continue to operate the robot if the device itself
or the power cord is damaged
Contact your local customer service in the event of
damage.
Do not clean the robot, the power cable in water or other
liquids.
Do not use the robot on damp ground or in places in
which it can get into contact with liquids or be immersed
in water.
Do not use the robot in hazardous areas such open
Make sure that you do not damage, bend or twist the
power cord. Do not place any heavy objects on top of
the cord. This could damage the power cord and cause
Safety Information
1.
5.
16.
4.
2.
13.
1.
6.
17.
5.
3.
14.
2.
7.
18.
6.
4.
15.
3.
8.
19.
7.
20.
8.
9.
10.
11.
9.
10.
11.
12.
Risk of Electric Shock!
6
operating the device.
Check if the safety rope is broken or the knot is loose
before operating the device.
Set danger-warning area downstairs for no- balcony
window and door.
Battery shall be full-charged (Orange lamp ON) before
using.
Do not use it in rainy or moist day.
Turn power on before put device onto glass.
Make sure the device can stick and stand on glass
surface while put onto glass.
Do not use it on frameless glass.
Make sure put cleaning pad on the bottom of device
correctly for no leakage.
Do not spray or pour water onto device.
Prohibit children from using this device.
Remove everthing on the glass. Do not use on cracked
scratched due to dirt on the glass while operating.
away from the openings and movingparts.
combustible liquids, gas.
1.
5.
2.
6.
3.
7.
4.
8.
9.
10.
11.
12.
13.
14.
15.
Warning
READ AND SAVE THESE
INSTRUCTIONS

Product Description
& Parameters
What's in the Package?
About the Robot
Adapter
Model No.
Rated Power
Battery Capacity
Dimension
Cleaning Speed
Input
BOBOT WIN SPIDER
75W
650mAh
25*25*7.2cm
About 2min/m²
AC100-240V 50/60Hz 2.0A
Rated Voltage
Noise Level
Net Weight
Output
DC 24V
About 60dB
1.25kg
DC 24V/3.75A
BOBOT WIN SPIDER Adapter User Manual Remote Control
Cleaning Pads Safety Rope
Power Cord
Indicator Light
Red: Alarm
Blue: Normal
Orange: Charing
Green: Fully Charged
Safety Lock Hole
Bottom Status
Indicator Light Velcro
Photoelectric Edge Sensor Anti Stuck Ring
Driving Tread
Fan
Red: Alarm
Blue: Normal
BOBOT WIN SPIDER will return to its starting point automatically
when cleaning is compleste.
Remote Control
Attach Cleaning Pad
Use remote control to
move your BOBOT WIN SPIDER
to a reachable location.
Grasp the handle and take
it off from the window.
A.
C.
B.
D.
Press button for 2
seconds to switch it off.
Untie the safety rope after
device and its spare parts
in dry condition for future
use.
Do not spray water on the fuselage
or the bottom of the machine. Spray
water only on the cleaning cloth.
Make sure the power is completely disconnected and the machine is turned off before
cleaning or maintaining the machine.
Do not drag the power plug through the extension cord, the power should be prop erly
unplugged.
Do not repair the product by yourself. Product maintenance must be carried out by an
authorized after-sales service center or distributor.
Do not wash the body and the power adapter with water.
Do not use this product in wet, water or other liquid situations, so as not to cause machine
failure or electric shock.
oom
with sprinkler running, swimming pool, etc.
If the supply cord is damaged, it must be replaced with a special cord or a special
component purchased from the manufacturer or repair department.
Before operation, make sure the safety rope is secured and securely attached to a secure
indoor installation.
Before starting the machine, check whether the safety rope is damaged and knotted
When cleaning Windows or doors without balconies, place a security warning area
downstairs.
Recharge the built-in standby battery (orange light) before use.
Do not use it in rainy or wet weather.
Make sure the machine is safely attached to the window before letting go.
Please hold the machine before turning it off to prevent it from falling.
Please use this product carefully to clean frameless Windows or glass.
Please make sure that the cleaning cloth is properly attached to the bottom ofthe machine
to prevent air leakage
Do not use this machine to clean broken glass. Some ground glass may scratch the
surface during cleaning. Please use with caution.
parts of the machine during use.
Important safety matters and warnings
Do not spray water on the fuselage
or the bottom of the machine. Spray
water only on the cleaning cloth.
Do not use a wet cloth to clean the
Windows. It may cause the machine
to get stuck on the glass surface.
No Use Yet
Start Cleaning
Manual Move Right
Manual Move Down
Automatically "N" Type
From "Z" to "N" Cleaning
Stop/Restart
Manual Move Up
Manual Move Left
Automatically "Z" Type
Stop Cleaning
Warning
78
Ultrasonic Edge Sensor

9
Use the product
Note: frameless glass and laminated
glass should be used with caution
Use frameless glass with care
The sensor can't tell the edge
IPlug in the safety lock into hole, turn it in clockwise
till indicator light changed to Green.
NOTE: Please start to use the robot ONLY when the
safety lock indicator light is in Green.
Secure the other end of the safety rope to other
objects in the room to ensure the fastening does
not fall off.
Frosted glass is not suitable
The number of window cleaning depends on the glass's own turbidity may
need to be wiped several times to clean!
machine outside window cleaning may have the
risk of falling! Special attention!
Product Maintenance
Use the Product
Stop/Pause
Press power button for 2
secondes to turn on your
BOBOT WIN SPIDER.
Put your BOBOT WIN SPIDER
up-side-down, take off the
cleaning pad and put it into cold
water, wash the cleaning
pad with detergent and dry
it for reuse.
Make sure the power is completely disconnected and the machine is turned off before cleaning or maintaining the machine.
Do not drag the power plug through the extension cord, the power should be properly unplugged.
Do not repair the product by yourself. Product maintenance must be carried out by an authorized after-sales service center or
distributor.
Do not continue to use the machine if the power supply is damaged.
If the machine is damaged, please contact the local after-sales service center or dealer for repair.
Do not wash the body and the power adapter with water.
Do not use this product in wet, water or other liquid situations, so as not to cause machine failure or electric shock.
Never damage or twist the power cord. Do not place heavy weights on the power cord or adapters to avoid damage to the power cord,
If the supply cord is damaged, it must be replaced with a special cord or a special component purchased from the manufacturer or
repair department.
Caution: Before starting, make sure the edge of BOBOT WIN SPIDER
is 8cm or more away from window frames or corners
.
During the cleaning process,
press the power button or the
STOP button on the remote
control to STOP the cleaning.
A.
A.
B.
B.
C.
C.
Place your BOBOT WIN SPIDER
on glass, press again the power
button to start.
Put your BOBOT WIN SPIDER
up-side-down, use a clean and
dry cloth to wipe out dirt/debris
on the fan.
During the cleaning process,
press the Pause key to Pause.
You can also start it from your
remote control "START" button.
Put your BOBOT WIN SPIDER
up-side-down, use a clean
and dry cloth to wipe out
dirt/debris on the sensors.
Put your BOBOT WIN SPIDER
up-side-down, use a clean
and dry cloth to wipe out
dirt/debris on it.
You can also press the “START”
button on the remote control to
START again.
1.
2.
Wash Cleaning Pad
1Clean Fan 2Clean Edge Sensors 3Cleaning Driving Treads 4
Note: wet cleaning pad is not
suggested to be used as it may get
your robot stuck when cleaning glass
with heavy dirty.
Beware of the risk of electric shock!
10

Troubleshooting
Malfunction Possible Causes Solutions
The device gets slippery or
works in irregular pattern.
A. Glass is too dirty or too wet.
B. Cleaning pad is too dirty or too
wet.
A.Change cleaning pad
B. Cleaning the driving treads
C. Use remote control to manually restart it.
Red indicator light.
A. Check if the cleaning pad is attached properly, replace it
correctly.
B. Check if any crack on the glass.
C. Check if the glass frames are with uneven area/rubber
part. If there is
uneven area or uneven rubber part on the glass, use remote
control to
operate the device manually and keep the W 120 away from
the
uneven area/uneven rubber part when cleaning.
The devices can't be started
after switched on, or works in
irregular pattern.
Edge detection sensor abnormal. A. Remove the Cleaning Pad and reattach
it making sure it is placed exactly within its Velcro area and
does not
cover the Edge Detection Sensors.
B. Open APP on your phone, connect it with the robot and
any RED indications on the corners of APP interface (Red
indications on
the APP interface means the edge sensor is malfunctioned).
C. Edge detection sensors failure, contact after-sales service.
buzzer beeps once/second.
Improper connection of Power
Supply.
Check if the plug is connected well, or the screws of the
extension cables are placed tight.
Both Red and Blue indicator Hardware failure. Contact after-sales service.
Remote control does not work. A. No battery insideor battery has
low power;
B. Remote control is broken.
A. Change the battery.
B. Replace the remote control with new one.
The device got stuck on glass
frames.
Edge-detection misjudgement. A. Press STOP on remote, move the device to reachable
B. Pull the robot lightly to reachable location if can't remote
control it.
Both Red and Blue Light on, no
beeps.
The device is not sucking
properly on window.
Put the device on window surface manually, make sure it
sucks on the window properly.
Buzzer beeps twice when it's in
use.
Edge sensor detects frameless
glass.
It's normal if it is cleaning frameless glass.
Squeaky sound when it's in
use.
Glass is too dry or edge detection
sensors are too dirty.
A. Spary a little water on the cleaning cloth.
B. Clean the edge detection sensors and operate again.
The device doesn't return to
Starting Point after cleaning.
The glass surface 's friction index Use remote control to direct the device return to reachable
location.
11

If you have a question about your machine, contact us via website
or call the Helpline.
BOBOT Customer Care
Printed in Shanghai 2020-5
BOBOT ROBOTICS INC. 16192 Binhai Road, Lewis, Sussex,Delaware, US