Body Solid GFLP User manual

Assembly Instructions v.031008
B u i l t F o r L i f e
GFLP

1
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. Do Not wrench tighten until the end of step 3.
*Some parts are pre-installed.
A. Attach Mainframe Assembly (A) to Back Foot Tube (B) and Back Plate (10) using:
Two 25 (M10 x 70 hex head bolt)
Four 35 (f10 washer)
Two 37 (M10 nylon lock nut)
B. Attach two Foot Caps (18) to Back Foot Assembly (B) as shown.
C. Attach Front Frame Assembly (C) to Mainframe Assembly (A) using Sleeve Tube (15) through the
Bearing’s (17) hole using:
Two 33 (M6 x 10 hex head socket set screw)
Two 34 (M8 x 30 button head cap screw)
Two 36 (Washer f8)
D. Put one End Cap (19) and two End Caps (20) onto Front Frame Assembly (C).
E. Screw Bumper (24) and nut (52) into Mainframe Assembly (A).
1

1
2

2
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. Do Not wrench tighten until the end of step 3.
*Some parts are pre-installed.
A. Attach Handle Foam (40) to Left Handle Frame Assembly (G) and Right Handle Frame Assembly
(F).
B. Attach Left Handle Frame Assembly (G) and Right Handle Frame Assembly (F) to Mainframe
Assembly (A) using:
Two 25 (M10 x 70 hex head bolt)
Four 35 (f10 washer)
Two 37 (M10 nylon lock nut)
C. Attach Seat Pad (K) to Mainframe Assembly (A) using:
Two 30 (M8 x 65 hex head bolt)
Four 36 (f8 washer)
D. Put two Nylon Bushings (21) and Pull-Pin (12) into Rear Frame Assembly (H).
E. Attach Rear Frame Assembly (H) to Mainframe Assembly (A) using:
Two 27 (M10 x 70 carriage bolt)
Two 35 (f10 washer)
Two 37 (M10 nylon lock nut)
F. Put two End Caps (22) and one End Cap (19) to Adjustable Frame Assembly (J).
G Attach Back Pad (K) to Adjustable Frame Assembly (J) using:
Two 31 (M8 x 40 hex head bolt)
Two 36 (f8 washer)
H. Attach Seat Pad (K) to Mainframe Assembly (A) using:
Two 30 (M8 x 65 hex head bolt)
Two 36 (f8 washer)
I. Attach Adjustable Frame Assembly (J) through Rear Frame Assembly (H) hole using Pull-Pin (12)
and lock it.
J. Using Socket Cap Screw (32) and Washer (36), lock in the Adjustable Frame Assembly (J) as
shown.
3

2
4

3
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. Do Not wrench tighten until the end of step 3.
*Some parts are pre-installed.
A. Attach Single Pulley Bracket (13) to Middle Plate (9) using:
Two 29 (M8 x 20)
Two 36 (f8 washer)
Two 38 (M8 nylon lock nut)
B. Attach Joint Assembly (D) and Middle Plate (9) to Mainframe Assembly (A) using:
Two 25 (M10 x 70 hex head bolt)
Four 35 (f10 washer)
Two 37 (nylon lock nut)
C. Attach Single Pulley Assembly (14) to Sleeve Tube Assembly (E) using:
One 28 (M10 x 65 hex head bolt)
Two 35 (f10 washer)
One 37 (M10 nylon lock nut)
D. Attach Sleeve Tube Assembly (E) through Joint Assembly (D) using:
Two 28 (M10 x 65 hex head bolt)
Four 35 (f10 washer)
Two 37 (nylon lock nut)
E. Attach Sleeve Tube Assembly (E) to BodySolid G2, G3, G4, G5, G6, G10, GSTK Mainframe Tube
using:
Two 25 (M10 x 70 hex head bolt) *USE WITH G2, G3, G5, G6
Four 35 (f10 washer) *USE WITH G4, G10, GSTK
Two 37 (M10 nylon lock nut)
One 11 (Bracket)
5

3
6
BodySolid Mainframe Tube

3A
7
BodySolid Mainframe Tube

4
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step.
*Some parts are pre-installed.
A. Attach the end of Cable (43) to Hook (39). Link the hook onto the triangular plate hole under the
Mainframe Assembly (1).
B. Attach Cable (43) around the three Pulleys (23) using:
Three 26 (M10 x 42 hex head bolt)
Six 35 (f10 washer)
Three 37 (M10 nylon lock nut)
C. Whensettingupthelongconguration,pleaseuseCable(43).
D. Whensettinguptheshortconguration,pleaseuseCable(44).
8

4
9
#43 Long Cable - Use with G2, G3, G4, G5, G6, G10, GSTK
with extended Telescopic Extension
#44 Short Cable - Use with G2, G3, GSTK
only with compacted Telescopic Extension