BODYKORE SMART SLED User manual

BodyKore
www.BodyKore.com
®
SMART SLED
Owner’s Manual
Read all precautions and instructions in
this manual before using this equipment.
Keep this manual for future reference.
CAUTION

2
Important Safety Guidelines for Owners
Assembly Guide
Follow these guidelines to maintain proper working condition of the equipment:
Important:Do not modify the equipment or any of its parts, or permanently remove
any part from the equipment. Do not use accessory attachments that are not
recommended by ours as such attachments might cause injuries.
• Qualified technicians must perform all regular maintenance.
• Make sure that trainers, facility personnel, and maintenance technicians
understand how to use the equipment, know important safety guidelines, and can
recognize potential problems such as a worn cable or cracked weld.
• Strength training requires a significant focus by the facility and its staff to
maintain the quality of the fitness environment. If possible, the facility should
provide direct supervision of the fitness equipment at all times by people
knowledgeable about the safe operation of the equipment and trained to
recognize potential problems.
• Make sure the equipment is stable and placed on a solid, level surface. The
equipment is designed to be freestanding; however, equipment can be bolted to
the floor for extra stability. Consult a qualified general contractor for proper
fastening methods.
• Make sure that the equipment is installed with enough free space for safe
operation.
• Place an “out-of-order” sign on the equipment during maintenance of the
equipment or the surrounding area. Users should never be allowed to operate the
equipment until it has been inspected and works properly. If a piece of equipment
needs service, keep it out of use until repaired.
• Do not place the equipment outdoors or on wet surfaces.

3
Assembly Instructions
It takes about 30 minutes to assemble this equipment. If this is your first time doing this,allowing
more time.
Be careful to open boxes and assemble components in the sequence presented in this manual.
Note: With so many assembled parts, proper alignment and
adjustment is critical. While tightening the fasteners, be sure to leave
room for adjustments.
Installation Requirement
• Unpack the boxes and assemble the equipment close to where you plan to use it.
• Locate equipment at least 40 inches (1 meter) away from any walls, furniture, or
objects on all sides.
• While tightening the fasteners. be sure to leave room for adjustments,DO NOT
fully tighten fasteners until instructed to do so.
• Set up and assemble the equipment on a solid, flat surface, so that it remains level and
stable.
Required Tools
• Hex wrench sets,metric and standard,plus extensions
• Wrench Set Metric
• Box cutter

4
Assembly Guide
Parts List
4
1
3
2
STEP 1
No. Descripon Qty
1 Sled Frame 1
2Keyed 12" Wheels 2
3 Caster Wheels 2
4 Counter Sunk Bolt Assembly for Caster Wheels 8
5 Weight Horn 2
6 Front Top Plate 1
7 Power Panel 1
8 Control Panel 1
9 Buon Head Asssembly for Weight Horn 4
10 Buon Head Bolt 8
11 Washer 8
12 Lock Washer 8
13 Handle 1

5
Assembly Guide
13
9
7
8
4
1
12
10
3
11
2
6
5
STEP 2

7
Daily Inspection
This section covers the tasks you should do each week to maintain the equipment.
Choose the appropriate tasks for your equipment, depending on what you are
maintaining:
1. Check the frame of the Smart Sled for any signs of damage or wear and tear.
Look for any cracks or bends in the metal and ensure that all bolts and screws
are tight and secure.
2. Inspect the wheels to make sure they are in good condition and are rolling
smoothly. Look for any signs of damage or wear on the wheels.
3. Check the motor and electronics to ensure they are functioning properly. Test the
controls and make sure that the motor is starting and stopping correctly. If you
notice any issues, refer to the manufacturer's instructions for troubleshooting or
contact their customer support team.
4. Check the handles and grips for any signs of damage or wear. Make sure they are
securely attached to the sled and are comfortable to hold.
5. Inspect the surface of the sled to ensure it is clean and free of debris or damage.
Wipe down the sled with a damp cloth to remove any sweat or dirt that may have
accumulated during use.
6. Check the area around the sled to ensure it is clear of any obstacles or hazards.
Make sure there is enough space to perform exercises safely and that the sled is
not in danger of colliding with any other equipment or objects.

8
Week Inspection
You will need to do the followingtasks each day to maintain the
equipment and keep it operating smoothly and safely.
Each of these tasks is covered in this section. You should perform those
tasks that are appropriate for the equipment
you are maintaining, and skip those tasks that do not apply.
1. Clean the sled thoroughly: Use a mild detergent and water to clean the entire
sled, including the weight plates or resistance bands, handles, and frame. Wipe
down the surface of the sled with a clean, dry cloth.
2. Check the battery: Check the battery to make sure it's holding a charge and
replace it if necessary. Follow the manufacturer's instructions for replacing the
battery.
3. Inspect the motor: Check the motor for any signs of wear or damage, and ensure
that it's still functioning properly. Refer to the manufacturer's instructions for
guidance on how to inspect the motor.
4. Check the resistance system: Inspect it to make sure it's working correctly. Test
the resistance levels and adjust them as needed.
5. Tighten bolts and screws: Inspect all bolts and screws on the sled and tighten
them as necessary. Loose bolts and screws can cause the sled to wobble or
become unstable during use.

9
Monthly Inspection
Each month, the followingtasks should be performed to maintain the equipment.
Choose the appropriate tasks based on what you are maintaining.
1. Check the power cord: Inspect the power cord and make sure it's in good
condition with no signs of fraying or damage. If the cord is damaged, contact the
manufacturer for a replacement.
2. Inspect the wheels: Remove the wheels from the sled and inspect them for any
signs of damage or wear. If the wheels are damaged or worn, replace them with
new ones.
3. Inspect the frame for rust or corrosion: Check the frame of the sled for any signs
of rust or corrosion. If you notice any issues, use a rust remover and paint over
the affected area to prevent further damage.

10
Troubleshoot
1. Issue: The sled has no resistance.
a. Solution: Make sure the power switch is on and the sled is fully charged.
Charging can be done with the micro USB charging cable provided. If the
sled still has no resistance, check the sled's weight load and make sure
it's set to the appropriate level for your workout.
2. Issue: One wheel is locked up.
a. Solution: Turn the whole system off and wait for at least 10 seconds
before turning it back on. If the problem persists, contact BodyKore
Customer Service for a replacement electronics box.
3. Issue: The sled is not connecting to the app.
a. Solution: First, shut down the sled and close out of the app. Start up both
again and try to connect. If that does not work, ensure that no other
device is connected to the sled and that the blue LED indicator light is off.
Once the light is off, try to connect again. If the issue persists, check if
your mobile device is compatible with the BodyKore Smart Sled app.
4. Issue: The manual control buttons do not work.
a. Solution: Make sure that the Bluetooth connection is not active by
ensuring that the Blue LED indicator light is off. The manual control
buttons should work when the sled is not connected to the app. If the
issue persists, contact BodyKore Customer Service for further
assistance.
If none of the above solutions work, please contact BodyKore customer support for
further assistance.