Bodyworx Jx735 User manual

1. OVERVIEW DRAWING

2. IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the

followings:

Read all instructions before using the treadmill.

DANGER – To reduce the risk of electric shock:

Always unplug this appliance from the electrical outlet immediately after using and before

cleaning.

WARNING– To reduce the risk of burns, fire, electric shock, or injury to persons:

1. The product should never be left unattended while plugged in. Unplug the product from the

outlet when not in use.

2. Close supervision is necessary when this product is used by or near children, invalids, or

disabled persons.

3. Be sure to use the product only for its intended use as described in this manual. Do not use any

attachment not recommended by the manufacturer in order to avoid any danger or accidents.

4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it

has been damaged, or dropped into water. Please return the product to the service center of

seller for examination and repair.

5. Do not carry this product by the supply cord or use the cord as a handle.

6. Keep the cord away from hot surfaces or ground.

7. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc.

8. Never drop or insert any objects into any openings.

9. Do not use or operate outdoors.

10. Do not operate where aerosol (spray) products are being used or where oxygen is thin.

11. Before turning the product power off, turn all controls to the off status then remove the plug

from the outlet.

12. Connect the product to a properly grounded outlet only.

13. If the treadmill is foldable, when user finishes using the treadmill, the elevation needs to be

back to original position.

14. When user is using the treadmill, it can not be folded at the same time.

15. This machine is only intended for household use.

Note–For the treadmill with folding function, be sure that the elevation is 0 before folding(To

avoid interference of the components).

3. GROUNDING INSTRUCTIONS

The products must be grounded first. If malfunction or breakdown occurs, grounding will provide

a path of least resistance for electric current to reduce the risk of electric shock.

The product is equipped with a cord having an equipment-grounding conductor and a grounding

plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Danger – Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or serviceman if you are in doubt as to

whether the products are properly grounded. Do not modify the plug provided with the

product – if it will not fit the outlet, have a proper outlet install by a qualified electrician.

The product is for use on nominal 220~240 volt and has a grounding plug that looks like

the plug illustrated in the figure. Make sure that the product is connected to an outlet

having the same configuration as the plug.

There is no need to use any adapter for this product.

Figure

Grounding methods

GROUNDED

OUTLET

GROUNDED

OUTLET

GROU

GROUNDED PIN

4. MOTORIZED TREADMILL PRE-ASSEMBLY

Handrail control button and heart rate strap are optional items in the package

1. Heart rate can be measured in this treadmill. Attach strap to chest during exercise, the heart rate value

will display on the PULSE window.

2. Except using the control button on the console, the control button on the handrail can also be used to

adjust speed and elevation. The control button on the left handrail is for elevation while the right handrail

button is for speed adjustment.

ITEM Description Qty

A Computer Console 1

B Frame 1

C Upright (L) 1

D Upright (R) 1

E Decoration Cover (L) 1

F Decoration Cover (R) 1

G Upper Handrail

Cover (L) 1

H Upper Handrail

Cover (R) 1

I Lower Handrail

Cover (L) 1

J Lower Handrail

Cover (R) 1

ITEM Description Qty

a Screw M5xP0.8x10 4

b Allen Bolt M8xP1.25x15 10

c Allen Bolt M8xP1.25x15 4

d Allen Bolt M8xP1.25x60 4

e Screw ψ4x16 6

f Allen Wrench +

Screwdriver

5mmx70mmx70mm 1

g Allen Wrench 6mm 1

h Power Cord 1

i Safety Key/Clip 1

j Lubricant 1

k Mp3 Sound Cable 1

5. ASSEMBLY STEPS

1. After pull out Control Wire with Guide Thread

in right Upright (D), put left and right Uprights

(C, D) to the suitable place and then fix with

Allen Bolt (b).

Ps. To avoid unexpected accident, always assemble the

treadmill with an assistant, do not assemble by

oneself.

Ps. When assemble the Uprights, one person should

hold the Upright to prevent it from falling.

2. After left and right Uprights are tightened, cap

left and right Decoration Covers (E, F) to the

Frame and tighten them with Screw (a).

3. Turn HandlebarAssembly upwards and

connect with the Computer. Tighten with

Allen Bolt (c).

4. Put Computer Console (A) on the treadmill

and connect all control wires. Then thread

them into the tube of the left and right

Handrails. Assemble Computer Console to the

Handrails and fix with Screw (d).

Ps. When fix the screws, pay attention that do not

damage control wires in the tube.

5. After finish above steps, cap left and right

Upper Handrail Covers (G, H) and Lower

Handrail Covers (I, J) to the Uprights. Fix with

Self Tapping Screw (e).

Ps. When fix the screws, pay attention that do not

damage control wires in the tube.

Ps. Pay attention when assemble the Handrail

Covers, after Upper Handrail Cover hooks the

Upper Computer Cover, then assemble it to the

Lower Handrail Cover.

6. CAUTION

Note: Made of high pressure, the cylinder

must be takeN care to avoid danger caused

by the impact with other objective.

Note: If the cylinder is hit, it may cause

damage and make the use not smooth.

When the user is folding the treadmill, it

may result in the falling of the frame and

cause injury.

This treadmill is foldable. All operation

should be stopped when folding (include

stopping walking belt, disconnecting power

cord), then fold up treadmill as shown on the

drawing. Please make sure the pedal stopper

is exactly in the slot of preventing the frame

from sliding down. Vice Versa, to unfold the

treadmill, step on the pedal stopper with the

direction shown on the drawing, then carefully

unfold the treadmill frame on to the ground.

Do not release the frame before it touches the

ground.

(Ps. 1. To prevent from any injury when

moving a folded treadmill, hold on to the

adjustment box with two hands. Then pivot

the treadmill towards you until the wheels of

the treadmill are rolling freely.)

(Ps. 2. Make sure the floor is cleared and flat

when moving the folded treadmill around.)

7. MAINTENANCE

1. Walking Belt Centering. If the Walking Belt tracks off

center to the right or left of the deck, first turn the

power off. Then use 6mm Allen wrench to tighten the

rear roller bolt on the side of the treadmill toward which

the belt is moving. For example, if the belt moves to

the left and the deck becomes exposed on the right,

tighten the bolt on the left side of the frame. Tighten

about 1/4 of turn (clockwise). If the belt does not

move back to the center of the treadmill, make another

adjustment to the same bolt. Once the Walking Belt

has been adjusted closer to the center, the treadmill can

be started again.

Ps.1: The above mentioned is pretty import, make sure to

follow the procedure.

Ps.2: Make sure the walking belt going on right without

any tracks off the centers it depends on the position

and weight.

2. It is recommended that the deck be lubricated every 6-12

months according to the frequency of usage. First, use

6mm Allen wrench to loosen the bolts in the end caps.

Pull up the Walking Belt, dispense the lubricant on the

deck, and spread evenly. After lubricating the deck,

center the belt, and check the belt tension. Adjust the

belt as mentioned in step 3. (Ps. If the belt happens to

slip, follow the above steps and lubricate the running

deck.)

SUGGESTED PREVENTIVE MAINTENANCE

SCHEDULE IN ACCORDANCE WITH THE

AVERAGE RUNNING SPEED

Measurement Speed Interval

6KM/hr below 1 year

6~12KM/hr 6 months

Metric 12KM/hr above 3 months

4mile/hr below 1 year

4~8mile/hr 6 months

English 8mile/hr above 3 months

ote: This preventive maintenance schedule is

only meant for home use. It is suggested to

maintain the unit every month for commercial

use.

8. Computer Instruction

MP3 jack is optional, not all machines have this function

I. Start Display:

1. If the SAFETY KEY is taken off, the matrix screen will display the arrow downwards. If

the SAFETY KEY is replaced, the matrix screen will display KGS (mile) for avoirdupois

unit. Weight window will blink and the preset value is 70KG (150LBS). Range is

23~130KG (50~286LBS). At this time, the light Weight indicates will be light.

Whether finish set or not set, press ENTER. This window will come back to start/ready

status and the matrix window displays pulsatile heart-shaped picture. The aim of setting

weight is to make a change of burning CALORIES. This can be only done after starting. It

does not need to set in PROGRAM. It means you can use the value after starting. You must

set newly after starting again.

2. When the SAFETY KEY is removed, the treadmill will stop running. At this time place the

SAFETY KEY back, the beeper will sound and then all the values will go back to the

initial position.

3. Under usual start/ready status, if you don’t hold pulse sensor, PULSE window will display HP.

When you hold the pulse sensor, you will see PULSE window displays pulse value.

II. Operation Mode：

1. Under start/ready status, press “Mode” to enter edit mode.

2. Under start/ready status, press Start to enter directly by “Manu run”.

3. When the SAFETY KEY is taken off and then replaced, it will not make reposition action

any where it is. You need to press start key to perform the incline to reposite it.

4. When power on, it will not make reposition action any where it is. You need to press start

key to perform the incline to reposite it.

5. Under start/ready status, continuously press stop key for 5 seconds, it will make

reposition action any where it is.

During perform any program, if press stop key, the program will stop. If users want to

continuously perform the program, press start key or again press stop key to leave the

program and back to start/ready status.

III. Edit Mode：

1. Under Start/Ready position, press Mode to choose Manual and Program mode by press +/-

key.

2. Program mode：Press +, - keys to edit Program（P1~P8）. The light PROGRAM

indicates blinks. LCD can display P1~P8 for users to edit. Press +, - to edit. Press

ENTER to enter TIME edit. The preset value is 30min，range is 20~99 min，STEP is 1 min.

After edit, press ENTER or START to start the machine. If you press START directly

during edit, the rest un-edited functions are pre-set. During edit, INCLINE and SPEED

window will display first level value. The matrix window will display this picture.

3. WARM UP and COOL DOWN function: During WARM UP or Program position, change

speed or inclination, the value will increase or decrease in the next level. COOL DOWN is

not affected and STOP is the only function which can be carried out.

4. PROGRAM has 30 levels in all. The three anterior are WARM UP, the three later are

COOL DOWN. Everyone is 3 minutes. The setting time except anterior and later which

mean 6 minutes will be execute averagely by surplus 24 levels.

5. 9 HOLES mode have not functions of WARM UP or COOL DOWN. When distance is

equal to 3.5KM, the motor will stop, the INCLINE is 0 and displays ” End”.

IV.Program Operation and Instruction：

Manu mode

1. When press Start, it will begin to count down for 3 seconds, after that, the motor will start ,

the speed will start at 0.8KPH（0.5MPH）. The matrix window goes contrarotate like along

playground, every circle is 0.4KM (0.25MIL).

2. Speed STEP is 0.1, you can press +, - keys to select（the speed UP/DOWN step is 0.1）, or

press speed instant key 1、2、4、6、8、10 to select .

3. Incline STEP is 1, you can press +, - keys to select（incline UP/DOWN step is 1）, or press

incline instant key 2、4、6、8、10、12 to select.

4. TIME set or not set:

(1) When TIME has bee set, the window will display a time value counting down from the

target value, when the time reaches 0:00, the treadmill will stop automatically.

(2) When TIME hasn’t been set, the window will display the exercise time, when the time

reaches 99:00, the treadmill will stop automatically.

5. When you press Mode key, it will switch among SPEED, DISTANCE and CALORIES

while INCLINE, PULSE or WEIGHT not, only displaying INCLINE. If there is PULSE, it

will mainly display Pulse. If there is pulse value, the pulse window will display pulse

value.

6. Press Stop when the motor is working, the motor will stop and the incline motor will stop,

the window will display Stop; If you press START key again, the motor will start after

3-seconds countdown , the speed will be keep at the same before stop , and the incline will

be increased to the set height before stop.

7. During Stop, press Stop and hold it for 3 seconds, it will switch to start/ready status.

8. Under End status, if it last 30 seconds（or press Stop key）, it will switch to start/ready

status.

9. The time pre-set value is 0, range 20~99,when the time is edited at 20 minutes , you can

press +- key to increase or decrease, the increase step is 1, if decrease , it will go back to 0

directly. During exercise, the matrix window goes contrarotate like along playground.

V. Program Mode

P1 Manu time：pre-set 0min；range 20~99min，step 1 min.

P2 9 hole LEVEL：pre-set 1，range 1~10，step1，3500 meter is based on distance.

P3 hill climb LEVEL：pre-set 1，range 1~10，step 1.

time：pre-set 30min；range 20~99min，step 1 min.

P4 hill run LEVEL：pre-set 1，range 1~10，step 1.

time：pre-set 30min，range 20~99min，step 1 min.

P5 interval LEVEL：pre-set 1，range 1~10，step 1.

time：pre-set 30min，range 20~99min，step 1 min.

P6 rolling LEVEL：pre-set 1，range 1~10，step1.

time：pre-set 30min，range 20~99min，step 1 min.

P7 Weight loss LEVEL：pre-set 1，range 1~10，step 1.

time：pre-set 30min，range 20~99min，step 1 min.

P8 Custom time：pre-set 30min，range 20~99min，step 1 min.

PROGRAM has 30 levels in all (SE01~SE30) and the pre-set values all are lowest values.

Setting：time，program execute value and setting time can execute in 30 level averagely.

（1）After enter program control function, the light that delegates LEVEL will be light and the

window will blink. This function is to choose the exercise intensity level (L1~L10). You

can or to change it to your required level and press ENTER to confirm.

（2）After the level is confirmed，the TIME window will blink. Press or

to set up the sport time. Or you can choose to press START directly to start move with

count down.

**Time range：20~99 min，the preset value is 30min，step is 1 min.

**If the machine has HRC function, P8 Custom will be replaced by HRC

function. The operation ways are as follows:

P8 HRC HRC function：(This function must be attached with heart beat to finish)

The program aims to exercise heartbeat. When operating, the heartbeat value is equal to the

pre-set value, the angle and speed will keep steady to maintain the heartbeat value in certain

range to achieve the exercising effect.

After you have selected this mode, the program will require you input the values according to

following ways:

1. AGE LCD flashes and press or to adjust the age. After finish setting, press

to enter next option. Age preset value：30. Range：13~80，Step is 1.

2. At this time LCD of PULSE light flashes, the mode will request you to put in heartbeat

value. The value will change according to the age and please refer to the attached table in

the rear of this indication. Then select the suitable value in the table. You can press or

to adjust heartbeat value. If you don’t make any change, press and mode will start

according to pre-set value and turn to next position.

3. TIME window starts flashing, mode will request you to put in time value. You can press

or to set sport time you need. Or press directly to start exercise with no

countback.

（* Range of time：20~99 min，pre-set value is 0 min，step is 1.）

** The chart below will show the relationship between different age and heart rate of this

product of HRC function：

Error Signal Display：

E1：The treadmill can’t read the speed value.

E6：In the range of ADC, incline motor doesn’t run.

E7：Incline is too height or too low(exceed the range).

** If it has any error signal, please connect with the sale agent

BPM BPM BPM BPM

Age H Pre-set L Age H Pre-set L Age H Pre-set L Age H Pre-set L

13 197 124 124 31 180 113 113 49 162 103 103 67 145 92 92

14 196 124 124 32 179 113 113 50 162 102 102 68 144 91 91

15 195 123 123 33 178 112 112 51 161 101 101 69 143 91 91

16 194 122 122 34 177 112 112 52 160 101 101 70 143 90 90

17 193 122 122 35 176 111 111 53 159 100 100 71 142 90 89

18 192 121 121 36 175 110 110 54 158 100 100 72 141 90 89

19 191 121 121 37 174 110 110 55 157 99 99 73 140 90 88

20 190 120 120 38 173 109 109 56 156 98 98 74 139 90 88

21 189 119 119 39 172 109 109 57 155 98 98 75 138 90 87

22 188 119 119 40 171 108 108 58 154 97 97 76 137 90 86

23 187 118 118 41 170 107 107 59 153 97 97 77 136 90 86

24 186 118 118 42 169 107 107 60 152 96 96 78 135 90 85

25 185 117 117 43 168 106 106 61 151 95 95 79 134 90 85

26 184 116 116 44 167 106 106 62 150 95 95 80 133 90 84

27 183 116 116 45 166 105 105 63 149 94 94

28 182 115 115 46 165 104 104 64 148 94 94

29 181 115 115 47 164 104 104 65 147 93 93

30 181 114 114 48 163 103 103 66 146 92 92

Note：The machine has a function to switch between the metric system and the inch system , the switch operation method:

Hold the ENTER key for 10 seconds at the Start/Ready position after power on. At this time , the window will display: 0（the inch system）

1（the metric system）

you can press ＋－ key to select. After select, press ENTER to confirm and then you can make the change.

SPEED AND ELEVATION CHANGES

9 HOLE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Level 1 ELEVATION 0.0 1.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.0

(MPH) 1.0 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 1.5 1.0