Borroughs WB132 series User manual

ASSEMBLY INSTRUCTIONS FOR BORROUGHS
WB132 series & WB122 series Work Benches
Basic Work Bench ..................................................................................2
Leveler Foot Plate ..................................................................................2
Shelf for Basic Work Bench....................................................................2
IMPORTANT - PRODUCT LIABILITY INFORMATION
Read all instructions before proceeding with installation. Vital product information pertaining to proper set-up and cautions are included. Failure to
follow these instructions may result in personal injury and/or property damage.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
1-50374-WB132-122
April 2016
CONTENTS
End Guards or Back Guard ....................................................................3
End Guards and Back Guard Combined................................................ 3
Limited Lifetime Warranty.......................................................................4
3002 N. Burdick Street, Kalamazoo, MI 49004
t: 800-748-0227 | f: 269-342-4161 | www.borroughs.com
ISO 14001:2004 and 9001:2008 Registered
Borroughs Corporation extends to the original purchaser from the date of purchase a lifetime limited warranty against manufacturing defects in material and workmanship. If a Borroughs product fails to perform because
of a manufacturing defect, Borroughs will examine it. If found defective, it will be repaired or replaced at our option. This warranty applies only to Borroughs products acquired directly from Borroughs Corporation or from
Authorized Borroughs Dealers. This warranty does not apply to any product which has been subject to misuse, negligence, or accident; has been damaged in shipment, storage, or installation; has been misapplied or has
been modified or repaired by unauthorized persons or been repaired with non-standard Borroughs replacement parts. This warranty specifically excludes claims for indirect, incidental, or consequential damages arising
in any way from a product defect. This warranty is exclusive, and exists in lieu of all other warranties, either expressed or implied. This warranty gives you specific legal rights; you may also have other rights which may
vary from state to state. Contact your Borroughs Selling Dealer, to obtain warranty service. You must make a written claim. Provide a copy of your purchase record and a written description of the warranty problem with your claim.
LIMITED LIFETIME WARRANTY
Borroughs Corporation
3002 N. Burdick Street, Kalamazoo, MI 49004
t: 800-748-0227 | f: 269-342-4161 | www.borroughs.com
ISO 14001:2004 and 9001:2008 Registered
Printed in the USA | ©2016 Borroughs Corporation | Form # 1-50374-WB132-122

BACK GUARD
END GUARD
(1 pr. required)
~
~
1
SHELF SUPPORT
2
FIGURE 10
3
3
Parts List "A"
Item Description Req'd.
1 Bench Top 1
2 Stringer 1
3 Leg Attachment Channel 2
4 Leg Weldment 2
5 Adjustable Foot 4
6 .312 (5/16) - 18 x .500 (1/2) Phillips T.H.M.S. 40
7 .312 (5/16) - 18 Keps Nut 32
8 .312 (5/16) - 18 Weldnut 8
Basic Work Bench
1
2
3
4
5
1. Lay bench top (Item 1) upside down on a
at surface.
2. Insert leg attachment channel (Item 3) into
bench top with the open area of channel
facing upward. Position attachment chan-
nel so that the holes in the end anges
are in line with the oval and rst hole in
the front and back anges of the bench
top. Fasten channel to bench top with (4)
screws and nuts (Items 6 & 7) as provided
in the hardware pack 293. See Figure 1.
Repeat procedure at the other end.
3. Stand leg weldment (Item 4) in place. (Leg
ts inside attachment channel). Position
leg so that holes in the sides of the leg
weldment are in line with the holes in the
sides of the attachment channel. Loosely
fasten leg and channel together with (4)
screws and nuts (Items 6 & 7) as provided
in hardware pack 293. See Figure 2.
Repeat procedure at the other end.
4. The stringer (Item 2) is to be attached so
the legs along the back edges of bench.
(BORROUGHS is stamped on the front
edge of Bench). Position stringer so that the
holes in the end of the stringer are in line
with the holes in the leg. Fasten stringer to
leg with (4) screws and weldnuts (Items 6 &
8) as provided in hardware pack 664. See
Figure 3. Repeat procedure at the other
end. Tighten screws holding leg weldments
and attachment channels together.
5. Insert adjustable foot (Item 5) into leg so
that the holes in the sides of the foot are
aligned with the holes in the sides of the
leg. At the desired height, fasten foot to
leg with (4) screws and nuts (Items 6 & 7)
as provided in hardware pack 293. See
Figure 4. Repeat procedure for the other
legs.
This completes assembly of the Basic Work
Bench. Put bench in upright position.
5
FIGURE 4
2
FIGURE 3
4
~
FIGURE 1
FIGURE 2
Tools Required: 1. Phillips Screwdriver
2. 1/2" Open End or Box Type Wrench
67
Leveler Foot Plate
Parts List "C"
Item Description Req'd.
1 Foot Plate Assembly 2 pair
2 .312 (5/16) Keps Nut 4
3 .312 (5/16) - 18 x .500 (1/2) Phillips T.H.M.S. 4
1. Lay work bench upside down on
a at surface.
2. Position the foot plate assembly (Item
1) so that the tee nut and leveling
screw align with and fits into the
center hole in the bottom ange of the
adjustable foot. The hole in the corner
of both the foot plate assembly and
the adjustable foot should also be in
line with each other. Fasten the foot
plate assembly to the adjustable foot
with (1) screw and nut (Items 2 & 3)
as provided in hardware pack 296.
Repeat procedure to the other legs of
the unit.
3. Place work bench in upright position.
Adjust leveling screws until work bench
is at the desired leveled position.
This completes assembly of the
Leveler Foot Plate.
Tools Required: 1. Phillips Screwdriver
2. 1/2" Open End or Box Type Wrench
2
3
ADJUSTABLE
FOOT
1
Shelf for Basic Work Bench
Parts List "D"
Item Description Req'd.
1 Bench Shelf 1
2 .312 (5/16) - 18 x .500 (1/2) Phillips T.H.M.S. 4
3 .312 (5/16) - 18 Keps Nut 4
Place the shelf (Item 1) on the shelf supports between the legs of the work bench with the
back edge of the shelf (the edge with the 90° ange is the back) approximately .062 (1/16")
from the back legs of the work bench. Position shelf so the two inner holes on each end of
the shelf are in line with the two inner holes of each shelf support. Fasten the shelf to the
shelf supports with (4) screws and nuts (Items 2 & 3) as provided in hardware pack 2, two
each end. See Figure 10.
This completes the Shelf assembly for the Basic Work Bench.
Tools Required: 1. Phillips Screwdriver
2. 1/2" Open End or Box Type Wrench
End Guards (applies to 132 series) 1
1
Parts List "F"
Item Description Req'd.
1 End Guard 1 pair
2 .312 (5/16) - 18 x .500 (1/2) Phillips T.H.M.S. 4
3 .312 (5/16) - 18 Keps Nut 4
Parts List "G"
Item Description Req'd.
1 Back Guard 1
2 .312 (5/16) - 18 x .500 (1/2) Phillips T.H.M.S. 7
3 .312 (5/16) - 18 Keps Nut 7
Position end guard (Item 1) so that the two holes align with the holes in
the side of the attachment channel. Fasten end guard to channel with (2)
screws and nuts (Items 2 & 3) as provided in hardware pack 2. Repeat
procedure at the other end.
This completes the End Guard assembly.
Position back guard (item 1) so that the ovals in the lower edge of the
back guard are in line with the holes in the back edge of the bench top.
(Flanges on the back guard are to be facing toward the front). Fasten back
guard to bench top with (5) screws and nuts (Items 2 & 3) as provided in
hardware pack 293.
This completes the Back Guard assembly.
NOTE: The extra (2) screws and nuts are used when the end guards and
back guard are combined on the work bench.
End Guards and Back Guard Combined (applies to 132 series)
Attach end guards and back guard to work bench as stated in the separate
assemblies for the end guards and back guard above. Flanges on back
guard are to be located inside of the end guards. Fasten end guards to
back guard with (1) screw and nut (Items 2 & 3) as provided in hardware
pack 293, at each corner.
This completes the assembly for the End Guards and Back Guard
Combined.
Back Guard (applies to 132 series)
Tools Required: 1. Phillips Screwdriver
2. 1/2" Open End or Box Type Wrench
Tools Required: 1. Phillips Screwdriver
2. 1/2" Open End or Box Type Wrench
~
3
PAGE 2 PAGE 3