Bosch 0 275 007 030 User manual

Electric Bicycle
OWNER’S MANUAL
BENUTZERHANDBUCH
GEBRUIKERSHANDLEIDING
LE MANUEL DU PROPRIÉTAIRE
IT IS IMPORTANT TO READ THE WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE RIDING YOUR NEW BICYCLE.
LESEN SIE SÄMTLICHE WARNHINWEISE UND ANWEISUNGEN IN DIESER BEDIENUNGSANLEITUNG VOR DER ERSTEN FAHRT MIT
IHREM NEUEN BIKE GRÜNDLICH DURCH.
H ET IS BELANGRIJK DE WAARSCHUWINGEN EN INSTRUCTIES IN DEZE HANDLEIDING TE LEZEN VÓÓR U MET UW NIEUWE FIETS RIJDT .
IL EST IMPORTANT DE LIRE LES MISES EN GARDE ET INSTRUCTIONS CONTENUES DANS CE MANUEL AVANT D’UTILISER VOTRE
NOUVEAU VÉLO.
epowered by
Active Line - Nyon

Welcome to our bike family
Thank you for purchasing your new bike.
We believe in bikes. We make high quality bikes that are built to last. That is why each bike we make comes with a limited
lifetime warranty.
We wish you many carefree and enjoyable cycling kilometers with your new bike!
However, if you experience any problems with your bike, do not hesitate to contact your local retailer. If the problem
persists, please call our customer service for a solution.
Willkommen in unserer fahrrad-familie
Vielen Dank für den Kauf ihres neuen Fahrrads.
Wir glauben an das Fahrrad. Wir produzieren hochwertige Fahrräder, damit Sie lange mit ihrem Kauf zufrieden sind.
Aus diesem Grund erhält jedes Fahrrad unsere eingeschränkte lebenslange Garantie.
Wir wünschen ihnen viele problemlose Kilometer und viel Spaß auf ihrem neuen Fahrrad!
Wie auch immer, solten Sie jemals Probleme mit ihrem Fahrrad bekommen, können Sie sich jederzeit an ihren örtlichen
Fachhändler wenden. Wenn das Problem weiterhin besteht, kontaktieren Sie bitte unseren Kundendienst, um eine Lösung
zu finden.
Welkom bij onze fietsfamilie
Dank u voor het kopen van uw nieuwe fiets.
Wij geloven in de kracht van fietsen. We maken hoogwaardige fietsen voor het leven. Daarom wordt elke fiets geleverd met
een beperkte levenslange garantie.
Wij wensen u vele zorgeloze en aangename fietskilometers toe!
Als u echter problemen ondervindt met uw fiets, neem dan contact op met uw plaatselijke fietsendealer.
Als het probleem niet wordt opgelost, vraag dan onze klantenservice om een oplossing.
bienvenue dans notre famille
Merci d’avoir acheté votre nouveau vélo.
Nous croyons aux vertus du vélo. Nous fabriquons des vélos de haute qualité, créés pour durer.
C’est la raison pour laquelle chaque vélo que nous fabriquons est livré avec une garantie à vie limitée.
Nous vous souhaitons de nombreux kilomètres à vélo agréables et sans problème !
Toutefois, si vous avez un souci avec votre vélo, n’hésitez pas à vous adresser à votre distributeur local.
Si le problème persiste, veuillez rechercher une solution auprès de notre service client.
www.trekbikes.com
www.diamantrad.com
Welcome - Willkommen - Welkom - bienvenue

Robert Bosch GmbH
Bosch eBike Systems
72703 Reutlingen
GERMANY
www.bosch-ebike.com
0 276 001 SAN (2015.07) T / 246 WEU
Active LineActive Line
Drive Unit | Nyon |
PowerPack 300/400/500 | Charger
0 275 007 030/03 2 | 1 270 020 907/915 |
0 275 007 509/510/529/513/514/531 | 0 275 007 907
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
nl Oorspronkelijke gebruiksaanwijzing
OBJ_BUCH-2620-001.book Page 1 Monday, July 13, 2015 6:17 PM
es Puedes consultar este manual traducido en tu idioma en www.trekbikes.com
it Puoi trovare la versione italiana di questo manuale sul sito www.trekbikes.com
da For dansk manual gå da venligst til www.trekbikes.com
no Du nner denne manualen på norsk på www.trekbikes.com
sv Översättning av denna manual i ditt eget språk hittar du på www.trekbikes.com
Tämän ohjeen löydät omalla kielelläsi osoitteesta www.trekbikes.com

0 276 001 SAN | (13.7.15) Bosch eBike Systems
2|
3
2
1
89
10
6
5
4
7
OBJ_BUCH-2620-001.book Page 2 Monday, July 13, 2015 5:40 PM

| 3
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
WALKWA L K
WALKWA L K
19
15
16 13
12
14
20
5
–
17 mm
11
4
3
17
18
BA
OBJ_BUCH-2620-001.book Page 3 Monday, July 13, 2015 5:40 PM

0 276 001 SAN | (13.7.15) Bosch eBike Systems
4|
A1
C1
A9
C6
C7
A8
A6
A5
A5
A7
A2
C7 C6
A4
A3
A3
A4
A6
OBJ_BUCH-2620-001.book Page 4 Monday, July 13, 2015 5:40 PM

| 5
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
A8
A5
A6
A9
A1
A2
A5
A6
A7
7°
D
C
OBJ_BUCH-2620-001.book Page 5 Monday, July 13, 2015 5:40 PM

0 276 001 SAN | (13.7.15) Bosch eBike Systems
6|
eBike Battery Charger 36-4/230 Active/Performance Line
0 275 007 907
Li-Ion
Use ONLY with BOSCH Li-Ion batteries
Input: 230V 50Hz 1.5A
Output: 36V 4A
Made in PRC
Robert Bosch GmbH, Reutlingen
C2
C1
C3
C4
C5
OBJ_BUCH-2620-001.book Page 6 Monday, July 13, 2015 5:40 PM

| 7
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
A3
C5
C6
A8
C6 A2
C3
C2
A4
F
E
OBJ_BUCH-2620-001.book Page 7 Monday, July 13, 2015 5:40 PM

0 276 001 SAN | (13.7.15) Bosch eBike Systems
8|
C5
C5
A2
A8
C7
C7
C6
C6
G
OBJ_BUCH-2620-001.book Page 8 Monday, July 13, 2015 5:40 PM

Robert Bosch GmbH
Bosch eBike Systems
72703 Reutlingen
GERMANY
www.bosch-ebike.com
0 276 001 SAN (2015.07) T / 246 WEU
Active LineActive Line
Drive Unit | Nyon |
PowerPack 300/400/500 | Charger
0 275 007 030/03 2 | 1 270 020 907/915 |
0 275 007 509/510/529/513/514/531 | 0 275 007 907
en Original instructions
OBJ_BUCH-2620-001.book Page 1 Monday, July 13, 2015 6:17 PM

Important to read before the fIrst rIde
The most important points for you to do
1. Even if you have ridden a bicycle for years, it is important for every person to read the general “Bike Owner’s manual”
and the specific “RIDE+ Owner’s manual” carefully before you ride on the new RIDE+ bicycle.
• Both manuals contains detailed information and useful suggestions about your new bicycle.
• Make sure that you understand the proper use, maintenance, and disposal of the components of the electrical system of
your new RIDE+ bicycle.
2. Think about safety. Your safety and that of other road users is very important.
• Do not ride the electric bike without the battery pack. The battery pack must be on the bike while riding, else the bike has no
lights when needed.
• Do not misuse the electric bike by riding it without a saddle. Some bikes have a quick release on the seat post.
If the saddle gets stolen, it may lead to hazardous situations when still riding on the electric bike without a saddle.
• Check your bike for normal operation, loose parts and defects before riding. If you find any problem, visit your bike dealer for
repairs before riding.
• Be aware that other road users do not expect that an electric bike can ride faster than a normal bike.
Riding faster also increases the risk of accidents.
• Do not ride abusively. Only ride in the use conditions specified for your bike. Condition 1 (paved roads with tires staying on
the ground) is valid for RIDE+ City/Trekking bikes, condition 3 (rougher surfaces, tires momentarily NOT on the ground ) is
valid for RIDE+ Mountain bikes.
Please refer to the general Bicycle Owner’s manual for more detailed information.
• Do not over load the rear rack. The maximum allowable weight for the rear rack on RIDE+ bikes is 20 kg for bikes with a rear
rack battery pack and 25 kg for bikes with a down tube battery.
3. The electric system of your new bicycle needs special attention.
• Do not clean your electric bicycle with a high pressure washer. Any electric system is sensitive for moisture.
High pressure water might ingress in connectors or other parts of the electric system.
• Handle your battery pack with care. Do not drop or impact the battery pack. Mishandling of the battery pack could lead to
severe damage or over-heating. In an extremely rare case, a battery pack that has been severely impacted or otherwise
mishandled could potentially catch fire. If you suspect damage to your battery pack, visit your dealer immediately for inspection.
4. Maintain the battery pack as instructed in this RIDE+ Owner’s manual.
Failure to follow these instructions may result in damage to your battery pack and may require battery pack replacement:
• Only charge the battery pack with the included Bosch charger.
• When not using the battery pack for a longer period, charge it to approx. 60 % (3 to 4 LEDs lit on the charge-control indicator).
Check the charge condition after 6 months. When only one LED of the charge-control indicator lights up, recharge the battery
pack again approx. 60 %.
• It is not recommended to have the battery pack connected permanently to the charger.
• When the battery pack is stored discharged (empty) for longer periods, it can become damaged despite the low selfdischarging
and the battery-pack capacity may be strongly reduced.
• Store the battery pack in a dry, well-ventilated location. Protect the battery pack against moisture and water.
• Under unfavourable weather conditions, it is recommended e.g. to remove the battery pack from the bike and store it in an
enclosed location until being used again.
• The battery pack can be stored at temperatures between -10°C and +60°C. For a long battery pack life, however, storing the
battery pack at room temperature of approx. 20°C is of advantage.
• Take care that the maximal storage temperature is not exceeded. As an example, do not leave the battery pack in a vehicle in
summer and store it out of direct sunlight.
• It is recommended to not store the battery pack on the bike.

5. Be careful when transporting a RIDE+ bike.
• An E-bike is heavier than a normal bike. If transporting on a vehicle, be aware of the maximum load capacity of the vehicle’s roof,
towing hook and/or of the applied bike carrier. Refer to the manual of the vehicle and bike carrier for details.
• Remove the controller, battery pack and, if present, panniers from the bicycle and store them elsewhere in the vehicle during
the drive.
• Always respect local laws about transportation of a(n electric) bicycle.
• Because Li-Ion battery packs of this size and power are considered ‘Dangerous goods, class 9’ when transporting, regulations
may restrict the transport of separate Li-Ion batteries in some places. The restrictions apply to most airlines and some trucking
companies. But, if you intend to ship or travel with your complete RIDE+ bike (with installed battery pack), the regulations are
less strict. Make sure to check ahead with your airline or carrier, before booking your trip, if it is allowed to travel with your
complete RIDE+ bike.
6. Visit your dealer on a regular basis for maintenance of your new bike.
• To guarantee the safe and proper functioning of the bike, the bike must be maintained on a regular basis, at least once a
year, by an authorized RIDE+ dealer.
• Your dealer has the right knowledge and equipment to maintain your RIDE+ bike.
• If you have questions about your new RIDE+ bicycle, ask your dealer!
Getting the most from your RIDE+ Bicycle

English–1
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
Drive Unit/
On-board computer Nyon
Safety Notes
General Safety Rules
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Save all safety warnings and instructions for future
reference.
The term “battery pack” used in these operating instructions, ir-
respective of model, refers both tostandard batterypacks (bat-
tery packs with holder on the bike frame) and to rack-type bat-
tery packs (battery packs with holder in the rear rack/carrier).
Make sure to not be distracted by the display of the on-
board computer. If you do not focus exclusively on the traf-
fic, you risk being involved in an accident. If you want to
make entries in your on-board computer other than switch-
ingthe assistancelevel, stopandentertheappropriate data.
Before beginning any exercise program, seek advice
from a doctor about which pressure you can place
yourself under. This is the only way to avoid potential
overloading.
When using a heart rate monitor the heart rate dis-
played may be distorted by electromagnetic interfer-
ence. The heart rates displayed are for reference only. No
liability can be accepted for consequences caused by
incorrectly displayed heart rates.
Safety Warnings for eBikes
Donot open the drive unityourself. The drive unitmust
be repaired only by qualified experts and only with
originalspareparts. This will ensure thatthesafety of the
driveunitismaintained.Unauthorised openingof thedrive
unit will void warranty claims.
Do not open Nyon. Opening Nyon can destroy it and void
any warranty claims.
All components mounted to the drive unit and all other
components of the eBike drive (e.g., the chainwheel,
chainwheel seat, pedals) may be replaced only with
identical components or components specifically ap-
provedforyoureBike bythebicyclemanufacturer.This
protects the drive unit against overload and damage.
Remove the battery pack from the eBike before begin-
ning work (e.g. inspection, repair, assembly, mainte-
nance, work on the chain, etc.) on the eBike, transport-
ing it by car or plane, or storing it. Unintentional
activation of the eBike system poses a risk of injury.
TheeBike system canswitch itselfonwhen theeBike is
pushed backwards.
The push-assistance function may only be used when
pushing the eBike. Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
Use only original Bosch battery packs approved for
your eBike by the manufacturer. Using other battery
packs can lead to injuries and pose a fire hazard. When us-
ing other battery packs, Bosch shall not assume any liabil-
ity and warranty.
Donotmake any modifications to youreBikesystem or
fit any other products which would be suitable for in-
creasing the performance of your eBike system. This
normally reduces the lifetime of the system and risks dam-
age to the drive unit and the bike. There is also a risk of los-
ingthe guaranteeandwarranty claimsonthebikeyouhave
purchased. By handling the system improperly you are al-
so endangering your safety and that of other road users,
thus running the risk of high personal liability costs and
possibly even criminal prosecution in the event of acci-
dents attributable to manipulation.
Please observe all national regulations on registering
and using eBikes.
Please read and observe the safety warnings and in-
structionsenclosed inthe operatinginstructions ofthe
battery pack as well as in the operating instructions of
your eBike.
Safety information relating to the navigation
system
Do not plan your routes whilst you are cycling. Stop and
wait until you are stationary before entering a new des-
tination. If you do not focus exclusively on the traffic, you
risk being involved in an accident.
Abandon your route if the navigation system suggests
a path or road which is too ambitious, risky or danger-
ous for you based on your cycling ability. Have your nav-
igation system propose an alternative route.
Do not ignore any road signs, even if the navigation
system tells you to take a specific route. The navigation
system cannot take roadworks or temporary diversions in-
to account.
Do not use the navigation system in situations which
are safety-critical or unclear (road closures, diver-
sions, etc.). Always carry extra maps and means of com-
munication with you.
OBJ_BUCH-2620-001.book Page 1 Monday, July 13, 2015 5:40 PM

English–2
0 276 001 SAN | (13.7.15) Bosch eBike Systems
Product Description and
Specifications
Intended Use
Thedrive unit is intendedonly for drivingyour eBike and must
not be used for other purposes.
Product Features (see page 2–3)
The numbering of the components shown refers to the illus-
trations on the graphic pages at the beginning of the manual.
All illustrations of bike parts except for the drive unit, on-
board computer including operating unit, speed sensor and
the corresponding holders are schematic and may differ on
your eBike.
1Joystick
2Button “Home”
3On-board computer
4Holder for on-board computer
5On/Off button for on-board computer
6Bike lights button
7Brightness sensor
8USB port
9Protective cap of USB port
10 Drive unit
11 Operating unit
12 Joystick on the operating unit
13 “Home” button on the operating unit
14 Decrease assistance level button
15 Increase assistance level button
16 Push-assistance button “WALK”
17 Lock latch for on-board computer
18 Locking screw for on-board computer
19 Speed sensor
20 Spoke magnet of the speed sensor
USB charging cable (Micro A – Micro B)*
* not illustrated; available as accessory
Technical Data
Drive Unit Drive Unit
Article number 0 275 007 030
0 275 007 032
Rated continuous output W250
Torque at drive, max. Nm 50
Rated voltage V36
Operating temperature °C –5...+40
Storage temperature °C –10...+50
Degree of protection IP 54 (dust and splash
water protected)
Weight, approx. kg 4
On-board computer Nyon
Article number 1 270 020 907/915
Internal memory
1 270 020 907
1 270 020 915
GB
GB 1 8
Max. charging current,
USB connection mA 500
Charging voltage,
USB connection V5
USB charging cable1) 1 270 016 360
Operating temperature °C –5...+40
Storage temperature °C –10...+50
Charging temperature °C 0...+40
Internal lithium-ion battery V
mAh 3.7 710
Protection type2) IP x7 (watertight)
Supported wi-fi standards 802.11b/g/n (2.4 GHz)
Weight, approx. kg 0.2
1) Not included as part of standard delivery
2) When USB cover is closed
Bike lights*
Rated voltage V6
Maximum output
–Frontlight
–Taillight
W
W8.4 0.6
* Not possible via the eBike battery pack inall country-specific versions,
depending on the statutory regulations
OBJ_BUCH-2620-001.book Page 2 Monday, July 13, 2015 5:40 PM

English–3
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
Assembly
Inserting and removing the eBike battery pack
Forinserting andremovingthe eBikebattery pack in/fromthe
eBike, please read and observe the battery pack operating
instructions.
Inserting and removing the on-board computer
(see figure A)
To inserttheon-board computer 3, slide itfrom the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 17
and slide the on-board computer toward the front out of the
holder 4.
Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 18 (thread M3, 8 mm long) from below into the
threadprovided inthe holder.Mount theholder backonto the
handlebar.
Checking the Speed Sensor (see figure B)
The speed sensor 19 and its spoke magnet 20 must be
mounted in such a manner that the spoke magnet, after a turn
ofthe wheel, moves pastthe speed sensorwith a clearanceof
at least 5 mm, yet no more than 17 mm.
Note: If the distance between speed sensor 19 and spoke
magnet 20 is too small or too large, or if the speed sensor 19
is not properly connected, the speed indication r3 will fail,
and the eBike drive unit will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 20 and fas-
tenthespoke magnet to the spokein such a mannerthatit runs
past the mark of the speed sensor at the correct clearance. If
the speed is still not being indicated in the speed indication r3
after this, please contact an authorised bicycle dealer.
Operation
Initial Operation
Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged eBike battery pack is inserted (see
operating instructions of the battery pack).
– The on-board computer is properly inserted in the holder
(see “Inserting and removing the on-board computer”,
page English–3).
Switching the eBike System On/Off
Options for switching on the eBike system:
– Place the on-board computer into the holder 4.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5of the on-
board computer.
–Whentheon-boardcomputerisinserted, press theOn/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals (ex-
cept when in the push aid feature, see “Switching the Push-
assistance mode On/Off”, page English–9). The motor out-
put depends on the settings of the assistance level on the on-
board computer.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
maticallyre-activatedas soonyoustartpedalingagainandthe
speed is below 25/45 km/h.
Options for switching off the eBike system:
–PresstheOn/Offbutton5of the on-board computer for at
least 1 second.
– Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
– Remove the on-board computer out of its holder.
If no power is drawn from the drive for about 10 minutes (e.g.
because the eBike is not moving) or no button is pressed on
the Nyon, the eBike system will shut down automatically to
save energy.
OBJ_BUCH-2620-001.book Page 3 Monday, July 13, 2015 5:40 PM

English–4
0 276 001 SAN | (13.7.15) Bosch eBike Systems
The “Nyon” operating system
The Nyon operating system consists of three components:
– the Nyon on-board computer with operating unit
– the smartphone application “Bosch eBike Connect”
–theonlineportal“www.eBike-Connect.com”
Many configurations and features can be managed and used
on all components. Some configurations and features can be
accessed or operated only via certain components. The syn-
chronization of data occurs automatically during Blue-
tooth®-/internet connection. The following table provides an
overview of the available features.
Premium features
The standard features of the “Nyon” operating system can be
expanded via the AppStore for Apple iPhones and Google
Play Store for Android devices through the purchase of “pre-
mium features”.
In addition to the free application “Bosch eBike Connect”
there are several fee-based premium features. A detailed list
of available additional applications can be found in the online
manual under “www.Bosch-eBike.com/nyon-manual”.
Initial Operation of the On-board Computer
Thebattery packis suppliedpartially charged.Before thefirst
use, the Nyon battery pack must be fully charged via the USB
port (see “Energy supply of the on-board computer”, page
English–8) or the eBike system.
In order to use all the features of the operating system, you
must also register online.
Registration at the On-board Computer
– Switchon the on-board computerusing the On/Off button 5.
–Usethejoystick1to select your preferred language (select
by pressing the joystick) and follow the instructions.
You have the following options to put Nyon into operation:
–“TEST RIDE”
Youcan perform a test ridewithout having to register in ad-
vanceorto enterdata. Aftershutting down,alltrip datawill
be deleted.
–“SET UP”>“OFFLINE”
This is a very short registration process limited to Nyon.
Offline means in this case that your journey and user data
are only saved locally on the on-board computer.
Follow the instructions and choose one of the suggested
answers. Entered data is kept after shutting Nyon down,
but will not be synced to the online portal or smartphone
application.
–“SET UP”>“ONLINE”>“PHONE”
This is a complete registration process. Insert Nyon in the
holder 4, download the application
“Bosch eBike Connect” to your smartphone and register
using the application. Following registration, the journey
data are stored and synchronized with the smartphone ap-
plication and the online portal.
–“SET UP”>“ONLINE”>“WI-FI”
This is a complete registration process. Connect Nyon via
USBto a powersupply (e.g. computer)andensure you are
in a WLAN network access area.Nyon then connectsto the
WLAN network of your choice and you will be directed to
the online portal “www.eBike-Connect.com” where you
can carry out the registration. Following registration, the
journey data are stored and synchronized with the online
portal. A connection to your smartphone can then be
created from your Nyon (“Settings”>“Connections”>
“Connect New Smartphone”).
On-board computer Smartphone application Online portal
Log in/registration 
Change of configurations 
Recording of journey data 
Real-time display of journey data 
Processing/analysis of journey data  
Creating user-defined displays  
Displays the current location* 
Navigation 
Route planning 
Display of remaining distance
(circle around the current location) 
Training effect in real-time 
Overview of journeys  
Statistics “Dashboard”  
Purchase of “premium features” 
*GPSrequired
GSM,
3/4G www
OBJ_BUCH-2620-001.book Page 4 Monday, July 13, 2015 5:40 PM

English–5
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
Registration via smartphone and Bluetooth® connection
A smartphone is not included in the delivery. To register with
the smartphone internet connection is required, which, de-
pending on the contract, can generate costs at your telephone
provider. For the synchronization of data between the smart-
phoneand online portalan Internetconnection is alsorequired.
To make use of the full functionality of your on-board comput-
er,you needa smartphonewith theAndroid operatingsystem
version 4.0.3 or higher or iOS 7 and higher. A list of tested/
approvedsmartphones, can be foundinthe online manual un-
der “www.Bosch-eBike.com/nyon-manual”.
Smartphones with the above mentioned operating systems,
which are not included in the list can be connected under cer-
tain circumstances with the on-board computer. However, a
complete compatibility of the on-board computer with the
smartphones not listed, can not be guaranteed.
Download the application “Bosch eBike Connect” to your
smartphone from the Appstore for Apple iPhones and Google
Play Store for Android devices.
Start the application “Bosch eBike Connect” and follow the
instructions. Detailed instructions can be found in the online
manual under “www.Bosch-eBike.com/nyon-manual”.
If the application “Bosch eBike Connect” is active and there
is a Bluetooth® connection to your on-board computer, data
between on-board computer and smartphone will sync auto-
matically.
Online registration
Internet access is required for online registration.
Open the online portal “Bosch eBike Connect” with your
browser under “www.eBike-Connect.com” and follow the
instructions. Detailed instructions can be found in the online
manual under “www.Bosch-eBike.com/nyon-manual”.
Displays and configurations of the
on-board computer
Operating logic
For security reasons, Nyon does not have a touch screen.
Achangeinthedisplaycanbeachieved duringthe journeyvia
the operating unit 11. This way both hands can stay on the
handlebars while cycling.
With the control elements on the on-board computer, you
have the following options:
– Switch the on-board computer on or off using the On/Off
button 5.
– The default mode of operation in “Settings”>“My Nyon”
can be reached via the “Home” (2or 13) button.
– The bike lights can be switched on or off using the bike light
button 6.
– Use the joystick 1to navigate through the respective oper-
ating modes. Make a selection by pressing the joystick 1.
Press left on the joystick 1to overlay the active operating
mode with the main menu and to switch it to the main menu
(see picture above).
If you press the joystick 1right while in the active operating
mode, the current screen is overlayed with the potential con-
figuration options of the current operating mode. Move the
joystick to the desired option and select it by pressing the joy-
stick 1.
Tip: If you are in an active operating mode, you can switch di-
rectlytothe nextoperatingmode bypressingthe joystick1up
or down.
If Nyon is on the eBike, “Ride” is displayed after switching on
the operating mode. If Nylon is not mounted on the eBike,
“Dashboard” is displayed on the operating mode.
Main Menu
Symbol Operating mode Function
“Dashboard” This operating mode offers
you statistical data.
“Ride” This operating mode pro-
vides current journey data.
“Map &
Navigation” You can use this operating mode to access map data
based on Open Street Map
(OSM). You can navigate us-
ing these maps.
“Fitness” Via this mode you can view
various fitness-related infor-
mation.
“Settings” This operating mode allows
you to set the basic configu-
rations of your on-board
computer.
Map & Navigaon
OBJ_BUCH-2620-001.book Page 5 Monday, July 13, 2015 5:40 PM

English–6
0 276 001 SAN | (13.7.15) Bosch eBike Systems
Operating mode “Dashboard”
This operating mode offers you statistical data.
d1 Clock
d2 Observation period
d3 Costs
d4 Savings
d5 Saved trees
d6 Total distance of cyclist
This operating mode shows you the savings d4 you have
made, when not using a car, but rather the eBike.
Basisforthe calculationis theaverageenergy costof fuel and
electricity.
Operating mode “Ride”
This operating mode provides current journey data.
r1 Clock
r2 Own pedal power
r3 Speed
r4 Engine power
r5 Assistance-level indicator
r6 Trip meter
r7 Average speed
r8 Coverage
r9 Charge level indicator of the eBike battery pack
Operating mode “Map&Navigation”
Youcan use thisoperating modeto access mapdata basedon
Open Street Map (OSM). You can navigate using these maps.
The map material suitable for the place of residence is in-
stalledby thebike dealerfor the respectivebuyer. Ifrequired,
additional maps can be downloaded via your smartphone ap-
plication “Bosch eBike Connect” and be transferred to your
on-board computer. Detailed instructions can be found in the
online manual under
“www.Bosch-eBike.com/nyon-manual”.
If you have an active wi-fi connection and Nyon is connected
to a power supply via the USB port, maps can be loaded di-
rectly onto Nyon via “Settings” >“Map & Navigation” >
“Map Manager”.
When you switch on Nyon, it begins the satellite search to re-
ceiveGPS signals. Oncesufficient satellite signalis found,the
operating mode displays “Map&Navigation” of the current
location. In case of unfavourable weather conditions or loca-
tions, the satellite search may take a little longer.
Pressing the joystick 1to the right allows you to change the
zoom configuration of the map section by selecting the sub
menu on the right side. You can display the range of your
eBike battery pack or choose one from different navigation
options.Thezoom configurationsforthe mapsectioncan also
be changed by pressing the joystick.
Your nearest “Bosch eBike experts” are also shown under
“PointsofInterest”. When you select a dealer,theroute to it
will be calculated and made available for you to select.
If you have entered the destination (town, street, house num-
ber), three different routes (“Scenic”, “Fast” and “MTB”
(Mountain bike)) will be provided for you to choose from.
Alternatively, you can opt to be guided home, select one of
the last destinations used, or choose from saved locations
and routes. (Detailed instructions can be found in the online
manual under “www.Bosch-eBike.com/nyon-manual”.)
The selected route will be displayed as shown in the figure
below.
n1 Clock
n2 Map
n3 Zoom level
n4 Compass needle
n5 Turn instructions and distance to the next turn
n6 Distance to destination
n7 Estimated time of arrival at destination
d6
d4
d2 d5
d3
d1
r9
r4
r5
r3 r7
r6
r8
r2
r1
n7
n3
n2 n5
n4
n6
n1
OBJ_BUCH-2620-001.book Page 6 Monday, July 13, 2015 5:40 PM

English–7
Bosch eBike Systems 0 276 001 SAN | (13.7.15)
During the navigation, the guidance (e.g. turn left in 50 meters)
will also be displayed via a cross fade in other operating modes.
If you interrupt a journey for which you are using navigation
and then call up “Map & Navigation”, you will be asked
whether or not you wish to continue navigation. If you contin-
uenavigation,the navigationsystemwill guideyouto yourlast
destination.
If you have imported GPX routes via the online portal, these
will be transferred to your Nyon via Bluetooth® or via a wi-fi
connection. You can start these routes when you wish. If you
are near a route, you can have the navigation system guide
you to the starting point or to an intermediate destination.
If you are using intermediate destinations, a message will in-
formyou when youhave reachedan intermediate destination.
Nylon is not suitable for a navigation without a bicycle (for hik-
ers or motorists).
Attemperatures below 0 °C, thealtitude measurement islike-
ly to deviate significantly.
Operating mode “Fitness”
Via this mode you can view various fitness-related information.
Based on the activity levels provided in your registration, the
effect of your previous activities will be displayed on your
stamina level (training effect).
Tocheck your heartrate, you canuse a cheststrap, which you
can connect to Nyon via Bluetooth®.
Compatible models can be found in the online manual under
“www.Bosch-eBike.com/nyon-manual”.
A chest strap is not included in the delivery.
f1 Clock
f2 Current performance/heart rate*
f3 Display of the current training effect
f4 Training effect
f5 Kilocalories burned
f6 Current cadence
f7 Average speed
f8 Duration
* When using a chest strap to measure the heart rate (not included
inthe delivery), your current heart rate will bedisplayedinsteadof
the performance.
Via the sub menus, you can reset the average values or switch
to individualised displays. Detailed instructions can be found
in the online manual under
“www.Bosch-eBike.com/nyon-manual”.
Operating mode “Settings”
This operating mode allows you to set the basic configura-
tions of your on-board computer.
Note: Some basic configurations can only be changed when
Nyon is inserted into the holder 4.
To reach the “Settings” menu, press the joystick 1down in
the main menu until “Settings” is displayed.
Tip: If you press the joystick down long enough, you will also
reach the “Settings” menu.
The following configurations can be made:
–“Connections”: You can configure the Bluetooth® config-
urations,anewsmartphone connection,aWiFiconnection
or a heart rate monitor.
When you enable WiFi, Nyon searches for available net-
works. Found networks will be displayed. Use the joystick
1to select the desired network and enter the password.
–“Set Altitude”: You can adjust the value displayed to the
actual altitude to compensate for weather-related
changes.
–“Map&Navigation”: Here you can configure the map
display and turn on automatic adaptation of the display,
dependant on the ambient brightness.
–“My Profile”: Here you can also choose to display the
active user.
–“My eBike”: When Nyon is plugged in, you can change the
pre-set value given by the manufacturer of the wheel cir-
cumference by ±5 %.
Thebicycle manufacturer maybase theservice date onthe
distancetravelled and/or on a periodof time. The duedate
for the service is displayed under “Service”.
–“My Nyon”: Here you can search for updates, configure
the Home button, automatically set the counters such as
tripmeter, calories burnedand averagevalues to “0”every
night, or reset Nyon to the factory settings.
–“Brightness”:You can adjust thebrightness of thedisplay
here.
–“International”: You can set speed and distance in kilo-
metres or miles, display clock in 12 or 24 hour format, se-
lect the time zone and set your preferred language. The
current time is automatically taken from the GPS signal.
–Inthe“Help” menu item, you will find a selection of FAQs
(frequently asked questions), contact details and informa-
tion about systems and licences.
f8
f4
f2 f6
f5
f7
f1
f3
OBJ_BUCH-2620-001.book Page 7 Monday, July 13, 2015 5:40 PM