Bosch GCL 25 Professional User manual

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-pt.com
1 618 C00 50R (2012.01) T / 190 XXX
GCL 25 Professional
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Ðñùôüôõðï ïäçãéþí ÷ñÞóçò
tr Orijinal işletme talimat
pl Instrukcja oryginalna
cs Původní návod k používání
sk Pôvodný návod na použitie
hu Eredeti használati utasítás
ru Îðèãèíàëüíîå ðóêîâîäñòâî ïî
ýêñïëóàòàöèè
uk Îðèã³íàëüíà ³íñòðóêö³ÿ ç åêñïëóàòàö³¿
ro Instrucţiuni originale
bg Îðèãèíàëíà èíñòðóêöèÿ
sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad
et Algupärane kasutusjuhend
lv Instrukcijas oriģinālvalodā
lt Originali instrukcija
ja オリジナル取扱説明書
cn 正本使用说明书
tw 正本使用說明書
ko 사용 설명서 원본
th หนังสือคูมือการใชงานฉบับตนแบบ
id Petunjuk-Petunjuk untuk
Penggunaan Orisinal
vi
BΩng hõëng dÿn nguy›n bΩn
ar
fa
ΕΎϤϴϠόΗϞϴϐθΘϟ΍ΔϴϠλϷ΍
Ϡλ΍ έΎ ίήσ ΎϤϨϫ΍έ
OBJ_BUCH-1546-001.book Page 1 Tuesday, January 24, 2012 4:13 PM

3|
1 618 C00 50R | (24.1.12) Bosch Power Tools
GCL 25
1
2
3
4
11
10
1
1
1
1
1
67
8
9
5
OBJ_BUCH-1546-001.book Page 3 Tuesday, January 24, 2012 4:14 PM

1 618 C00 50R | (24.1.12) Bosch Power Tools
4|
FE
DC
BA
OBJ_BUCH-1546-001.book Page 4 Tuesday, January 24, 2012 4:14 PM

5|
1 618 C00 50R | (24.1.12) Bosch Power Tools
17
5
5
13
16
12
2 607 990 031
BS 150
0 601 096 974
14
2 607 002 195
2 608 438 692
15
BM 1
0 601 015 A00
BT 350
0 601 015 B00
OBJ_BUCH-1546-001.book Page 5 Tuesday, January 24, 2012 4:14 PM

English | 11
Bosch Power Tools 1 618 C00 50R | (24.1.12)
Tel. Kundenberatung: [phone]
(Festnetzpreis 9 ct/min, höchstens 42 ct/min aus Mobil-
funknetzen)
Fax: [phone]
E-Mail: [email protected]
Österreich
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Schweiz
Tel.: [phone]
Fax: [phone]
Luxemburg
Tel.: [phone]
Fax: [phone]
E-Mail: outillage.gere[email protected]
Entsorgung
Messwerkzeuge, Zubehör und Verpackungen sollen einer
umweltgerechten Wiederverwertung zugeführt werden.
Werfen Sie Messwerkzeuge und Akkus/Batterien nicht in den
Hausmüll!
Nur für EU-Länder:
Gemäß der europäischen Richtlinie
2002/96/EG müssen nicht mehr ge-
brauchsfähige Messwerkzeuge und gemäß
der europäischen Richtlinie 2006/66/EG
müssen defekte oder verbrauchte Akkus/
Batterien getrennt gesammelt und einer
umweltgerechten Wiederverwendung zu-
geführt werden.
Nicht mehr gebrauchsfähige Akkus/Batterien können direkt
abgegeben werden bei:
Deutschland
Recyclingzentrum Elektrowerkzeuge
Osteroder Landstraße 3
37589 Kalefeld
Schweiz
Batrec AG
3752 Wimmis BE
Änderungen vorbehalten.
English
Safety Notes
Working safely with the measuring tool is
possibleonlywhentheoperatingandsafety
information are read completely and the
instructions contained therein are strictly
followed.Never makewarning labelson the
measuring tool unrecognisable. SAVE
THESE INSTRUCTIONS.
fCaution – The use of other operating or adjusting
equipmentor theapplication ofotherprocessing meth-
ods than those mentioned here, can lead to dangerous
radiation exposure.
fThe measuring tool is provided with a warning label in
English (marked with number 10 in the representation
of the measuring tool on the graphics page).
fDo not direct the laser beam at persons or animals and
do not stare into the laser beam yourself. This measur-
ing tool produces laser class 2 laser radiation according to
IEC 60825-1. This can lead to persons being blinded.
fDo not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tionof the laserbeam,but theydonot protectagainstlaser
radiation.
fDonotuse thelaserviewing glassesassunglassesorin
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.
fHave the measuring tool repaired only through quali-
fied specialists using original spare parts. This ensures
that the safety of the measuring tool is maintained.
fDo not allow children to use the laser measuring tool
without supervision. They could unintentionally blind
other persons or themselves.
fDonot operatethemeasuring toolinexplosive environ-
ments, such as in the presence of flammable liquids,
gases or dusts. Sparks can be created in the measuring
tool which may ignite the dust or fumes.
Keep the measuring tool and the laser
target plate 13 away from cardiac pace-
makers.The magnetsofthe measuringtool
and laser target plate generate a field that
can impair the function of cardiac pace-
makers.
fKeep the measuring tool and the laser target plate 13
away from magnetic data medium and magnetically-
sensitive equipment. The effect of the magnets of the
measuring tool and laser target plate can lead to irreversi-
ble data loss.
Product Description and
Specifications
Please unfold the fold-out page withthe representation ofthe
measuring tool and leave it unfolded while reading the operat-
ing instructions.
Intended Use
The measuring tool is intended for determining and checking
horizontal and vertical lines as well as plumb points.
OBJ_BUCH-1546-001.book Page 11 Tuesday, January 24, 2012 4:18 PM

12 | English
1 618 C00 50R | (24.1.12) Bosch Power Tools
Product Features
The numbering of the product features shown refers to the
illustration of the measuring tool on the graphic page.
1Exit opening for laser beam
2Operating mode button
3Battery low indicator
4On/Off switch
5Magnets
6Tripod mount 5/8"
7Tripod mount 1/4"
8Latch of battery lid
9Battery lid
10 Laser warning label
11 Serial number
12 Laser viewing glasses*
13 Laser target plate
14 Measuring plate with stand*
15 Universal holder*
16 Tripod*
17 Case
* The accessories illustrated or described are not included as
standard delivery.
Technical Data
Assembly
Inserting/Replacing the Battery
Alkali-manganese batteries are recommended for the meas-
uring tool.
To open the battery lid 9, slide the latch 8in the direction of
the arrow and fold the battery lid up. Insert the batteries.
When inserting, pay attention to the correct polarity accord-
ing to the representation on the inside of the battery lid.
Whenthebatteriesarelow,thebattery low indicator3flashes
red. Additionally, the laser beams flash for approx. 5 s every
10 minutes. When the flashing initially begins, the measuring
tool can be operated for approx. 1 more hour. When the bat-
teries become empty, the laser beams flash one more time di-
rectly prior to the automatic shut-off.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
fRemove the batteries from the measuring tool when
not using it for extended periods. When storing for ex-
tended periods, the batteries can corrode and discharge
themselves.
Operation
Initial Operation
fProtectthe measuring toolagainst moistureand direct
sun light.
fDo not subject the measuring tool to extreme tempera-
tures or variations in temperature. As an example, do
not leave it in vehicles for long time. In case of large varia-
tions in temperature, allow the measuring tool to adjust to
the ambient temperature before putting it into operation.
In case of extreme temperatures or variations in tempera-
ture, the accuracy of the measuring tool can be impaired.
fAvoid heavy impact or falling of the measuring tool.
Afterheavy exteriorimpact onthe measuringtool,an accu-
racy check should always be carried out before continuing
to work (see “Levelling Accuracy”).
Point and line laser GCL 25
Article number 3 601 K66 B00
Working range1)
– Laser lines
– Horizontal point beams
– Point beam, upward
– Point beam, downward
10 m
30 m
10 m
5m
Levelling accuracy
– Laser lines and horizontal
point beams
– Vertical point beams
±0.3 mm/m
±0.5 mm/m
Self-levelling range, typically ±4°
Levelling duration, typically <4s
Operating temperature –10 °C ... +50 °C
Storage temperature –20 °C ... +70 °C
Relative air humidity, max. 90 %
Laser class 2
Laser type 635 nm, <1 mW
C61
Tripod mount 1/4", 5/8"
Batteries 4x1.5VLR06(AA)
1) The working range can be decreased by unfavourable environmental
conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 11
on the type plate.
Battery life for the operating
modes
– Cross and point-line operation
– 5-point operation
– Line operation
12 h
24 h
30 h
Weight according to
EPTA-Procedure 01/2003 0.6 kg
Dimensions
(length x width x height) 155x56x118mm
Degree of protection IP 54 (dust and splash
water protected)
Point and line laser GCL 25
1) The working range can be decreased by unfavourable environmental
conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your measuring
tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 11
on the type plate.
OBJ_BUCH-1546-001.book Page 12 Tuesday, January 24, 2012 4:18 PM

English | 13
Bosch Power Tools 1 618 C00 50R | (24.1.12)
fSwitch the measuring tool off during transport. When
switching off, the levelling unit, which can be damaged in
case of intense movement, is locked.
Switching On and Off
To switch on the measuring tool, slide the On/Off switch 4to
the “on”position (when working without automatic level-
ling) or to the “on”position (when working with automat-
ic levelling). Immediately after switching on, the measuring
tool sends laser beams out of the exit openings 1.
fDo not point the laser beam at persons or animals and
do not look into the laser beam yourself, not even from
a large distance.
To switch off the measuring tool, slide the On/Off switch 4to
the “off” position. When switching off, the levelling unit is
locked.
Deactivating the Automatic Shut-off
When no button on the measuring tool is pressed for approx.
30 minutes, the measuring tool automatically switches off to
save the batteries.
Toswitch onthemeasuring toolafter automaticshut-off, either
slide the On/Off switch 4to the “off” position and then switch
themeasuringtoolonagainorpresstheoperatingmode button
2once.
To deactivate the automatic shut-off, keep the operating
mode button 2pressed for at least 3 s (while the measuring
tool is switched on). Deactivation of the automatic shut-off is
confirmed by brief flashing of the laser beams.
fDo not leave the switched on measuring tool unattend-
ed and switch the measuring tool off after use. Other
persons could be blinded by the laser beam.
To activate the automatic shut-off, switch the measuring tool
off and then on again.
Operating Modes
The measuring tool has several operating modes between
which you can switch at any time:
– Cross and point-line operation: The measuring tool gener-
ates a horizontal and a vertical laser line facing toward the
front as well as a vertical point beam each facing upward
and downward, and a horizontal point beam each facing
toward the front and to both sides.
– 5-point operation: The measuring tool generates a vertical
point beam each facing upward and downward, as well as
ahorizontalpointbeam each facingtowardthefrontand to
both sides.
– Horizontal line operation: The measuring tool generates a
horizontal laser line facing frontward.
– Verticalline operation:Themeasuring toolgenerates aver-
tical laser line facing frontward.
All point beams run at a 90° angle to each other; the laser
lines also cross each other at a 90° angle.
After switching on, the measuring tool is in cross-line and
point-line operation. To change the operating mode, press
the operating mode button 2.
Alloperating modescanbe selectedbothwith andwithoutau-
tomatic levelling.
Automatic Levelling
Working with Automatic Levelling (see figures C–E)
Positionthemeasuring tool onalevelandfirm support,attach
it to the holder 15 or to the tripod 16.
When working with automatic levelling, push the On/Off
switch 4to the “ on”position.
After switching on, the automatic levelling function automati-
callycompensatesirregularitieswithintheself-levelling range
of ±4°. The levelling is finished as soon as the laser points or
laser lines do not move any more.
If the automatic levelling function is not possible, e.g. be-
cause the surface on which the measuring tool stands devi-
ates by more than 4° from the horizontal plane, the laser
beams flash. This alarm is deactivated within 10 s after
switching on, in order to allow adjustment of the measuring
tool.
Set up the measuring tool in level position and wait for the
self-levelling to take place. As soon as the measuring tool is
within the self-levelling range of ±4°, the laser beamslight up
continuously.
In case of ground vibrations or position changes during oper-
ation, the measuring tool is automatically levelled in again. To
avoiderrors bymovingthe measuringtool,check theposition
of the laser beams with regard to the reference points upon
re-levelling.
Working without Automatic Levelling (see figure F)
For work without automatic levelling, push the On/Off switch
4to the “ on”position. When the automatic levelling is
switched off, the laser lines flash continuously.
When automatic levelling is switched off, you can hold the
measuring tool freely in your hand or place it on an inclinded
surface. The laser beams no longer necessarily run vertical to
each other.
Levelling Accuracy
Influences on Accuracy
The ambient temperature has the greatest influence. Espe-
cially temperature differences occurring from the ground
upward can divert the laser beam.
As thermal fluctuation is largest close to the ground, the
measuring tool, if possible, should be mounted on a commer-
cially available tripod and placed in the centre of the working
area.
Apart from exterior influences, device-specific influences
(such as heavy impact or falling down) can lead to deviations.
Therefore, check the accuracy of the measuring tool each
time before starting your work.
When the accuracy of the horizontal point beams is within the
maximum allowed deviation, then the accuracy of the vertical
point beams and the laser lines is thus also checked.
Should the measuring tool exceed the maximum deviation
during one of the tests, please have it repaired by a Bosch af-
ter-sales service.
OBJ_BUCH-1546-001.book Page 13 Tuesday, January 24, 2012 4:18 PM

14 | English
1 618 C00 50R | (24.1.12) Bosch Power Tools
Checking the Horizontal Levelling Accuracy of the Lateral
Axis
Afree measuringdistance of20 mon a firm surface in front of
a wall is required for the check.
– Mount the measuring tool onto the holder or a tripod, or
place it on a firm and level surface at a distance of 20 m to
the wall. Switch the measuring tool on and select 5-point
operation.
– Direct one of the two lateral laser beams, that run along-
sidethe lateralaxisof themeasuringtool, atthewall. Allow
the measuring tool to level in. Mark the centre of the laser
beam on the wall (point I).
– Rotate the measuring tool by approx. 180° without chang-
ing its height. Allow it to level in and mark the centre point
of the other lateral laser beam on the wall (point II). Take
care that point II is as vertical as possible above or below
point I.
– The difference dof both marked points Iand II on the wall
results in the actual height deviation of the measuring tool
alongside the lateral axis.
On the measuring distance of 2 x 20 m = 40 m, the maximum
allowable deviation is:
40 m x ±0.3 mm/m = ±12 mm.
Thus,thedifference dbetween pointsIandII maynotexceed
12 mm (max.).
Checking the Horizontal Levelling Accuracy of the Longi-
tudinal Axis
A free measuring distance of 20 m on a firm surface between
two walls A and B is required for the check.
– Mount the measuring tool onto the holder or a tripod, or
place it on a firm and level surface close to wall A. Switch
the measuring tool on and select 5-point operation.
– Direct the horizontal laser beam, which runs parallel to the
longitudinal axis of the measuring tool, at the close wall A.
Allow the measuring tool to level in. Mark the centre of the
laser beam on the wall (point I).
– Turn the measuring toolaround by180°, allow it to level in
and mark the centre point of the laser beam on the oppo-
site wall B (point II).
– Withoutturning the measuringtool,position it closetowall
B. Switch the measuring tool on and allow it to level in.
– Align the height of the measuring tool (using the tripod or
by underlaying, if required) in such a manner that the cen-
tre point of the laser beam is projected exactly against the
previously marked point II on wall B.
20 m
d
180°
AB
20 m
180° B
A
AB
OBJ_BUCH-1546-001.book Page 14 Tuesday, January 24, 2012 4:18 PM

English | 15
Bosch Power Tools 1 618 C00 50R | (24.1.12)
– Rotate the measuring tool by 180° without changing the
height. Allow it to level in and mark the centre point of the
laser beam on wall A (point III). Take care that point III is
as vertical as possible above or below point I.
– The difference dof both marked points Iand III on wall A
results in the actual height deviation of the measuring tool
alongside the Longitudinal axis.
On the measuring distance of 2 x 20 m = 40 m, the maximum
allowable deviation is: 40 m x ±0.3 mm/m = ±12 mm.
Thus, the difference dbetween points Iand III may not ex-
ceed 12 mm (max.).
Working Advice
fFor marking, always use only the centre of the laser
pointorthe laserline.The sizeofthe laser pointaswell as
the width of the laser line change with distance.
Working with the Tripod (Accessory)
Atripodoffersastable, height-adjustablemeasuringsupport.
Positionthe measuringtool withthe1/4" tripodmount 7onto
the thread of the tripod 16 or a commercially available cam-
eratripod.For fasteningtoa commerciallyavailable construc-
tion tripod, use the 5/8" tripod mount 6. Tighten the measur-
ing tool with the tripod mounting stud.
Adjust the tripod roughly before switching on the measuring
tool.
Fastening with the Universal Holder (Accessory)
With the universal holder 15, you can fasten the measuring
tool,e.g.,to verticalsurfaces,pipes or magnetizablematerials.
The universal holder is also suitable for use as a ground tripod
and makes the height adjustment of the measuring tool easier.
Adjust the universal holder roughly before 15 switching on
the measuring tool.
Working with the Measuring Plate (Accessory)
(see figures A–B)
With the measuring plate 14, it is possible to project the laser
mark onto the floor or the laser height onto a wall.
With the zero field and the scale, the offset or drop to the
required height can be measured and projected at another
location. This eliminates the necessity of precisely adjusting
the measuring tool to the height to be projected.
Themeasuringplate 14hasareflective coatingthatenhances
the visibility of the laser beam at greater distances or in
intense sunlight. The brightness intensification can be seen
only when viewing, parallel to the laser beam, onto the meas-
uring plate.
Working with the Laser Target Plate
The laser target plate 13 increases the visibility of the laser
beam under unfavourable conditions and at large distances.
The reflective part of the laser target plate 13 improves the
visibility of the laser line. Thanks to the transparent part, the
laser line is also visible from the back side of the laser target
plate.
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient light. This
makes the red light of the laser appear brighter for the eyes.
fDo not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tionof the laserbeam,but theydonot protectagainstlaser
radiation.
fDonotuse thelaserviewing glassesassunglassesorin
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.
Work Examples (see figures C – F)
Applicational examples for the measuring tool can be found
on the graphics pages.
Always position the measuring tool close to the surface or
edge subject to checking, and allow it to level in prior to each
measurement.
Always measure the distances between laser beam or laser
lineanda surfaceoredgeat twopointsasfar aspossibleaway
from each other (e.g. with the measurment plate 14).
Maintenance and Service
Maintenance and Cleaning
Store and transport the measuring tool only in the supplied
case.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool in water or other fluids.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
Regularly clean the surfaces at the exit opening of the laser in
particular, and pay attention to any fluff of fibres.
If the measuring tool should fail despite the care takenin man-
ufacturing and testing procedures, repair should be carried
out by an authorised after-sales service centre for Bosch
power tools. Do not open the measuring tool yourself.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the measuring tool.
For repairs, only send in the measuring tool in the case.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
d
180°
AB
OBJ_BUCH-1546-001.book Page 15 Tuesday, January 24, 2012 4:18 PM

16 | English
1 618 C00 50R | (24.1.12) Bosch Power Tools
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: [phone]
Fax: [phone]
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: [phone]
Fax: [phone]
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: [phone]
Fax: [phone]
Inside New Zealand:
Phone: [phone]
Fax: [phone]
Outside AU and NZ:
Phone: [phone]
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: [phone]
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Bosch Headquarters
Midrand, Gauteng
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: [phone]
Fax: [phone]
E-Mail: [email protected]
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: [phone]
Fax: [phone]
E-Mail: [email protected]
www.bosch-pt.com.hk
Indonesia
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: [phone]
Fax: [phone] 23
E-Mail: [email protected]
www.bosch-pt.co.id
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio Global City,
1634 Taguig City, Philippines
Tel.: [phone]
Fax: [phone]
[email protected]
www.bosch-pt.com.ph
Bosch Service Center:
9725-27 Kamagong Street
San Antonio Village
Makati City, Philippines
Tel.: [phone]
Fax: [phone]
[email protected]
OBJ_BUCH-1546-001.book Page 16 Tuesday, January 24, 2012 4:18 PM