Bosch UML-262-90 User manual

Full HD LCD Monitors
UML-262-90 | UML-422-90
en User’s Manual

Full HD LCD Monitors Table of Contents | en 3
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
Table of Contents
1Safety 5
1.1 Important safety instructions 5
1.2 Safety precautions 8
1.3 Important notices 8
1.4 Customer Support and Service 15
2 Unpacking 17
2.1 Parts List 17
3 Monitor Panels 18
3.1 UML-262-90 Front Control Panel 18
3.2 UML-262-90 Bottom Panel 19
3.3 UML-422-90 Front Panel 19
3.4 UML-422-90 Rear Control Panel 20
3.5 UML-422-90 Bottom Panel 21
3.6 Remote Control 22
3.7 Remote Control Battery Installation 24
4 Description 25
4.1 Features 25
4.2 Power 26

4en | Table of Contents Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
5 Installing the Monitor 27
5.1 Ventilation 27
5.2 Mounting the Monitor 27
5.2.1 Desktop Installation 27
5.2.2 Wall Mount Installation 29
5.3 Connecting the Composite Video Signal to the Monitor 30
5.4 Connecting the Y/C (S-Video) Signal to the Monitor 31
5.5 Connecting Audio to the Monitor 31
5.6 Connecting the PC Signal to the Monitor 32
5.6.1 HDMI Connection 32
5.6.2 DVI Connection 32
5.6.3 VGA Connection 32
5.7 Connecting an Alarm Trigger 33
5.8 Single / Multiple Monitor Configuration 35
6 Navigating the Monitor 37
6.1 Navigating the Front Panel 37
6.2 Navigating the Monitor On-screen Display (OSD) 38
6.3 On-screen Display Menus 39
6.4 Custom Menu 40
6.5 Picture/Sound Menu 41
6.6 PIP Menu 44
6.7 Setup Menu 45
7 Power Management 48
7.1 Power Consumption 48
7.2 LED Indicator 48
8Troubleshooting 49
9 Maintenance 50
10 Technical Specifications 51

Full HD LCD Monitors Safety | en 5
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
1Safety
1.1 Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
1. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a dry cloth for cleaning is sufficient, but a moist fluff-
free cloth or leather shammy may also be used. Do not use
liquid cleaners or aerosol cleaners.
2. Heat Sources - Do not install the unit near any heat
sources such as radiators, heaters, stoves, or other
equipment (including amplifiers) that produce heat.
3. Ventilation - Any openings in the unit enclosure are
provided for ventilation to prevent overheating and ensure
reliable operation. Do not block or cover these openings.
Do not place the unit in an enclosure unless proper
ventilation is provided, or the manufacturer's instructions
have been adhered to.
4. Water - Do not use this unit near water, for example near a
bathtub, washbowl, sink, laundry basket, in a damp or wet
basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To
reduce the risk of fire or electrical shock, do not expose
this unit to rain or moisture.
5. Object and liquid entry - Never push objects of any kind
into this unit through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electrical shock. Never spill liquid of any
kind on the unit. Do not place objects filled with liquids,
such as vases or cups, on the unit.
6. Lightning - For added protection during a lightning storm,
or when leaving this unit unattended and unused for long
periods, unplug the unit from the wall outlet and

6en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
disconnect the cable system. This will prevent damage to
the unit from lightning and power line surges.
7. Controls adjustment - Adjust only those controls specified
in the operating instructions. Improper adjustment of
other controls may cause damage to the unit. Use of
controls or adjustments, or performance of procedures
other than those specified, may result in hazardous
radiation exposure.
8. Overloading - Do not overload outlets and extension cords.
This can cause fire or electrical shock.
9. Power cord and plug protection - Protect the plug and
power cord from foot traffic, being pinched by items
placed upon or against them at electrical outlets, and its
exit from the unit.
10. Power disconnect - Units have power supplied to the unit
whenever the power cord is inserted into the power
source. The power cord is the main power disconnect
device for switching off the voltage for all units.
11. Power sources - Operate the unit only from the type of
power source indicated on the label. Before proceeding,
be sure to disconnect the power from the cable to be
installed into the unit.
– For battery powered units, refer to the operating
instructions.
– For external power supplied units, use only the
recommended or approved power supplies.
– For limited power source units, this power source
must comply with EN60950. Substitutions may
damage the unit or cause fire or shock.
– If unsure of the type of power supply to use, contact
your dealer or local power company.
12. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.

Full HD LCD Monitors Safety | en 7
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
13. Damage requiring service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel when any damage to the equipment has
occurred, such as:
– the power supply cord or plug is damaged;
– exposure to moisture, water, and/or inclement
weather (rain, snow, etc.);
– liquid has been spilled in or on the equipment;
– an object has fallen into the unit;
– unit has been dropped or the unit cabinet is damaged;
– unit exhibits a distinct change in performance;
– unit does not operate normally when the user
correctly follows the operating instructions.
14. Replacement parts - Be sure the service technician uses
replacement parts specified by the manufacturer, or that
have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical
shock, or other hazards.
15. Safety check - Safety checks should be performed upon
completion of service or repairs to the unit to ensure
proper operating condition.
16. Installation - Install in accordance with the manufacturer's
instructions and in accordance with applicable local codes.
17. Attachments, changes or modifications - Only use
attachments/accessories specified by the manufacturer.
Any change or modification of the equipment, not
expressly approved by Bosch, could void the warranty or,
in the case of an authorization agreement, authority to
operate the equipment.

8en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
1.2 Safety precautions
1.3 Important notices
All-pole power switch - Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building. If it is needed to open the
housing for servicing and/or other activities, use this all-pole
switch as the main disconnect device for switching off the
voltage to the unit.
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as “Dangerous Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious
injury and/or serious damage to the unit. Use only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer. When a cart is used, use caution and care when
moving the cart/apparatus combination to avoid injury from
tip-over. Quick stops, excessive force, or uneven surfaces may
cause the cart/unit combination to overturn. Mount the unit
per the manufacturer's instructions.

Full HD LCD Monitors Safety | en 9
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
Coax grounding:
– Ground the cable system if connecting an outside cable
system to the unit.
– Connect outdoor equipment to the unit's inputs only after
this unit has had its grounding plug connected to a
grounded outlet or its ground terminal is properly
connected to a ground source.
– Disconnect the unit's input connectors from outdoor
equipment before disconnecting the grounding plug or
grounding terminal.
– Follow proper safety precautions such as grounding for
any outdoor device connected to this unit.
U.S.A. models only - Section 810 of the National Electrical Code,
ANSI/NFPA No.70, provides information regarding proper
grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors,
location of discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Electronic Surveillance - This device is intended for use in
public areas only. U.S. federal law strictly prohibits
surreptitious recording of oral communications.
Environmental statement - Bosch has a strong commitment
towards the environment. This unit has been designed to
respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET
handling precautions to avoid electrostatic discharge.
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that electronic
and electrical appliances, which have reached the end of their
working life, must be collected and disposed of separately
from household waste material. Separate collecting systems
are usually in place for disused electronic and electrical
products. Please dispose of these units at an environmentally
compatible recycling facility, per European Directive 2002/96/
EC

10 en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
NOTE: Wear required grounded wrist straps and observe proper
ESD safety precautions when handling the electrostatic-
sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch
circuit protection must be secured with a maximum fuse rating
of 16A. This must be in accordance with NEC800 (CEC Section
60).
Grounding and polarization - This unit may be equipped with a
polarized alternating current line plug (a plug with one blade
wider than the other blade). This safety feature allows the plug
to fit into the power outlet in only one way. If unable to insert
the plug fully into the outlet, contact a locally certified
electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding
plug (a plug with a third pin for earth grounding). This safety
feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally
certified electrician to replace the obsolete outlet. Do not
defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move
the unit with care. Excessive force or shock may damage the
unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially
regarding clearance from power and lightning conductors and
transient protection, must be in accordance with NEC725 and
NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily
accessible disconnect device in the building installation wiring.
Pluggable equipment - Install the socket outlet near the
equipment so it is easily accessible.
Power resupply - If the unit is forced to power down due to
exceeding the specified operating temperatures, disconnect
the power cord, wait for at least 30 seconds, and then
reconnect the power cord.

Full HD LCD Monitors Safety | en 11
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
Power lines - Do not locate the display near overhead power
lines, power circuits, or electrical lights, nor where it may
contact such power lines, circuits, or lights.
Rack-mount
– Ventilation - Do not place this unit in a built-in installation
or rack without proper ventilation or adhering to the
manufacturer's instructions. The equipment must not
exceed its maximum operating temperature requirements.
– Mechanical loading - Properly mount the equipment in a
rack to prevent a hazardous condition due to uneven
mechanical loading.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV)
circuits. SELV circuits should only be connected to other SELV
circuits.
Because the ISDN circuits are treated like telephone-network
voltage, avoid connecting the SELV circuit to the Telephone
Network Voltage (TNV) circuits.
System ground/Safety ground
The system ground is only used to comply with safety standards
or installation practices in certain countries. Bosch does not
recommend connecting system ground to safety ground unless
it is explicitly required. However, if the system ground and
safety ground are connected and grounding loops are causing
interference in the video signal, use an isolation transformer
(available separately from Bosch).
Video loss - Video loss is inherent to digital video recording;
therefore, Bosch Security Systems cannot be held liable for any
damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security
Systems recommends multiple, redundant recording systems,
and a procedure to back up all analog and digital information.
CAUTION!
Connecting System ground to Safety ground may result in
ground loops that can disrupt the CCTV system.

12 en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following conditions:
– this device may not cause harmful interference, and
– this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and radiates
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct
the interference at his expense.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
NOTICE!
This is a class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.

Full HD LCD Monitors Safety | en 13
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en
service est soumises aux deux conditions suivantes :
– cet appareil ne peut pas provoquer d'interférence nuisible
et
– cet appareil doit pouvoir tolérer toutes les interférences
auxquelles il est soumit, y compris les interférences qui
pourraient influer sur son bon fonctionnement.
AVERTISSEMENT : Suite à différents tests, cet appareil s’est
révélé conforme aux exigences imposées aux appareils
numériques de Classe A en vertu de la section 15 du règlement
de la Commission fédérale des communications des États-Unis
(FCC). Ces contraintes sont destinées à fournir une protection
raisonnable contre les interférences nuisibles quand l'appareil
est utilisé dans une installation commerciale. Cette appareil
génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux
instructions, générer des interférences nuisibles aux
communications radio. L’utilisation de ce produit dans une
zone résidentielle peut provoquer des interférences nuisibles.
Le cas échéant, l’utilisateur devra remédier à ces interférences
à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un
technicien qualifié en radio/télévision, qui procédera à une
opération corrective. La brochure suivante, publiée par la
Commission fédérale des communications (FCC), peut s’avérer
utile : How to Identify and Resolve Radio-TV Interference Problems
(Comment identifier et résoudre les problèmes d’interférences
de radio et de télévision). Cette brochure est disponible auprès
du U.S. Government Printing Office, Washington, DC 20402,
États-Unis, sous la référence n° 004-000-00345-4.

14 en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Closed
Circuit Television Equipment, UL 2044. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL 60950-1. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
Copyright
This manual is the intellectual property of Bosch Security
Systems and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and must be
treated accordingly.

Full HD LCD Monitors Safety | en 15
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
NOTE!
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
1.4 Customer Support and Service
If this unit needs service, contact the nearest Bosch Security
Systems Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Repair Center-
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Customer Service
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Technical Support
Telephone: [phone]
Fax: [phone] or 717-735-6560
E-mail: [email protected]
Canada
Telephone: [phone]
Fax: [phone]
Europe, Middle East, Africa Region
Repair Center
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]

16 en | Safety Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
Asia Region
Repair Center
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Customer Service
Telephone: [phone] or
86 (0) 756 7633121
Fax: [phone]
E-mail: [email protected]
Warranty and more information
For additional information and warranty queries, please contact
your Bosch Security Systems representative or visit our website
at www.boschsecurity.com.

Full HD LCD Monitors Unpacking | en 17
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
2 Unpacking
This equipment should be unpacked and handled with care. If
an item appears to have been damaged in shipment, notify the
shipper immediately.
Verify that all the parts listed in the Parts List below are
included. If any items are missing, notify your Bosch Security
Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to
transport the unit and must be used if returning the unit for
service. Save it for possible future use.
2.1 Parts List
Quantity Description
1 UML-262-90 or UML-422-90 Color LCD Flat Panel
Monitor
1 Installation Manual
(printed booklet, English version)
1 Installation Manual
(printed booklet, Japanese version)
1 Installation manual
(CD-ROM, multi-language version)
2 Power Cords, 3-wire with grounded plug 1.8 m (6 ft)
long: one with a U.S plug type and one with a
European Continental plug type
1 Power adapter (UML-262-90 only)
1 DVI-D to DVI-D cable, 1.8 m (6 ft)
1 VGA to VGA (D-Sub) cable, 1.8 m (6 ft)
1 Trigger cable
1Remotecontrol
2 AAA batteries

18 en | Monitor Panels Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
3 Monitor Panels
3.1 UML-262-90 Front Control Panel
Figure 3.1 UML-262-90 Front Panel
Ref. Button Description
1 Enter Selects the signal to be displayed.
2 Menu Opens the on-screen display (OSD) menus.
3 Adjusts the value when in the OSD.
Activates the Auto Adjust function
when in PC mode.
Scrolls down in the OSD.
4 Adjusts the value when in the OSD. Scrolls up in the OSD.
5 Decreases the value when in the OSD.
Decreases audio volume.
Scrolls left in the OSD.
6 Increases the value when in the OSD.
Serves as the Enter function for OSD
menus.
Increases audio volume.
Scrolls right in the OSD.
7 Power Display power (On/Off)
8 Adjustable
Stand
Detachable stand that allows you to freely adjust the viewing
angle of the monitor.
9IRSensorand
LED Indicator
Receives command signals from the remote control.
Indicates the operating status of the monitor:
–Power On (green)
–Power Off, Standby (red)

Full HD LCD Monitors Monitor Panels | en 19
Bosch Security Systems, Inc. User’s Manual F.01U.172.600 | 1.0 | 2010.10
3.2 UML-262-90 Bottom Panel
Figure 3.2 UML-262-90 Bottom View (I/O panel)
3.3 UML-422-90 Front Panel
Figure 3.3 UML-422-90 Front View
Ref. Ref.
1 24 VDC In 8 Video 1 (AV1) In
2 HDMI In 9 Video 1 (AV1) Out
3 DVI-2 In 10 Video 2 (AV2) Out
4 DVI-1 In 11 Video 2 (AV2) In
5 RS-232 In (for firmware updates) 12 Trigger Input
6 VGA in 13 Audio In (Left/Right)
7 S-Video In
Ref. Button Description
1IRSensorand
LED Indicator
Receives command signals from the remote control.
Indicates the operating status of the monitor:
–Power On (green)
–Power Off, Standby (red)

20 en | Monitor Panels Full HD LCD Monitors
F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
3.4 UML-422-90 Rear Control Panel
Figure 3.4 UML-422-90 Rear View and Control Panel
Ref. Button Description
1 Handles Use handles when installing and transporting the monitor.
2 Kensington Lock
Hole
Use to install a Kensington-type lock to prevent theft.
3 Input Selects the signal to be displayed.
4 Menu Opens the on-screen display (OSD) menus.
5 Adjusts the value when in the OSD.
Activates the Auto Adjust function
when in PC mode.
Scrolls down in the OSD.
6 Adjusts the value when in the OSD. Scrolls up in the OSD.
7 Decreases the value when in the OSD.
Decreases audio volume.
Scrolls left in the OSD.
8 Increases the value when in the OSD.
Serves as the Enter function for OSD
menus.
Increases audio volume.
Scrolls right in the OSD.
9 Power Display power (On/Off)
10 LED Indicator Indicates the operating status of the monitor:
–Power On (green)
–Power Off, Standby (red)