Bosch Rexroth IndraControl VDP 15.3 Multi Touch User manual

IndraControl
VDP 15.3, 18.3, 21.3
Multi Touch
Operator Display – Built-In Devices
Operating Instructions
R911341191
Edition 03

Bosch Rexroth AG
Change Record
Edition 03, 2018-08
Refer to tab. 1-1 "Change Record" on page 1
Copyright
© Bosch Rexroth AG 2018
All rights reserved, also regarding any disposal, exploitation, reproduction, edit-
ing, distribution, as well as in the event of applications for industrial property
rights.
Liability
The specified data is intended for product description purposes only and shall
not be deemed to be a guaranteed characteristic unless expressly stipulated in
the contract. All rights are reserved with respect to the content of this documen-
tation and the availability of the product.
Editorial Department
Development Automation Systems Control Hardware HB (MaKo/MePe)
RS-efc79664d5c1106b0a6846a5001b631e-3-en-US-12

Table of Contents
Page
1 About this documentation..................................................................... 1
1.1 Overview on target groups and product phases.................................... 1
1.2 Purpose.................................................................................................. 1
1.3 Availability.............................................................................................. 2
1.4 Related documents................................................................................ 2
1.5 Customer feedback................................................................................ 2
2 Product identification and scope of delivery......................................... 2
2.1 Product identification............................................................................ 2
2.2 Scope of delivery................................................................................... 3
3 Using safety instructions........................................................................ 3
3.1 Structure of the safety instructions....................................................... 3
3.2 Explaining signal words and safety alert symbol................................... 4
3.3 Symbols used......................................................................................... 5
3.4 Explaining the signal alert symbol on the device................................... 5
4 Intended use.......................................................................................... 5
5 Spare parts, accessories and wear parts.............................................. 6
5.1 Y-repeater............................................................................................... 6
5.2 External 24 V power supply unit............................................................ 6
5.3 Uninterruptible power supply (UPS)..................................................... 6
5.4 Connecting cables for CDI interface...................................................... 7
5.5 Connecting cables for the USB interface............................................... 7
5.6 Wear parts............................................................................................. 8
6 Ambient conditions................................................................................ 8
7 Technical data...................................................................................... 10
7.1 General technical data......................................................................... 10
7.2 Optical characteristic values................................................................ 10
7.2.1 TFT....................................................................................................... 10
7.2.2 Input system (multi-touch front).......................................................... 10
8 Standards............................................................................................ 11
8.1 Standards used.................................................................................... 11
Bosch Rexroth AG
Table of Contents
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P I

Page
8.2 CE marking........................................................................................... 11
8.2.1 Declaration of conformity.................................................................... 11
8.3 UL/CSA certified.................................................................................. 12
9 Interfaces............................................................................................. 12
9.1 View..................................................................................................... 12
9.2 Overview.............................................................................................. 13
9.3 24 V DC voltage supply........................................................................ 13
9.4 S1 DIP switch...................................................................................... 14
9.4.1 Overview.............................................................................................. 14
9.5 USB interfaces..................................................................................... 14
9.5.1 Operating USB ports at operator display............................................ 14
9.6 XSER and XVID interfaces.................................................................... 15
9.6.1 CDI interface........................................................................................ 15
9.6.2 XVID and XSER marking....................................................................... 15
10 Mounting, demounting and electric installation.................................. 16
10.1 Housing dimensions............................................................................. 16
10.1.1 Rexroth design..................................................................................... 16
10.1.2 Special Rexroth design........................................................................ 17
10.1.3 Bosch design........................................................................................ 18
10.2 Installation notes................................................................................. 18
10.3 Mounting.............................................................................................. 18
10.4 Mounting cut-out................................................................................. 21
10.5 Demounting......................................................................................... 21
10.6 Electric connection.............................................................................. 22
10.6.1 Connecting operator display to control cabinet.................................. 22
10.6.2 Connecting operator display to 24 V voltage supply............................ 24
10.6.3 Overall connection scheme.................................................................. 25
10.6.4 Recommendation for the mounting of CDI cables with long lengths
in an interference-prone environment................................................. 25
11 Commissioning.................................................................................... 28
12 Device description............................................................................... 29
12.1 General information............................................................................. 29
12.2 Operating and error displays............................................................... 29
13 Error causes and troubleshooting........................................................ 29
Bosch Rexroth AG
Table of Contents
II DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

Page
14 Maintenance........................................................................................ 30
14.1 Display................................................................................................. 30
14.2 Cleaning notes..................................................................................... 31
14.3 Scheduled maintenance tasks............................................................. 31
15 Ordering information........................................................................... 31
15.1 Accessories and spare parts................................................................ 31
15.2 Type code............................................................................................. 32
16 Disposal............................................................................................... 32
16.1 Take-Back............................................................................................. 32
16.2 Packaging............................................................................................. 33
17 Service and support............................................................................ 33
Index.................................................................................................... 35
Bosch Rexroth AG
Table of Contents
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P III

Bosch Rexroth AG
IV DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

1 About this documentation
Editions of this documentation
Edition Release
Date
Notes
Edition 01 2013-10 First edition
Edition 02 2014-03 Revision
Edition 03 2018-05 Accessories supplemented, corrections
Tab. 1-1: Change Record
1.1 Overview on target groups and product phases
In the following illustration, the framed activities, product phases and target
groups refer to the present documentation.
Example: In the product phase "Mounting (assembly/installation)", the "mechan-
ic/electrician" can execute the activity "install" using this documentation.
Presales Aftersales
Selection Mounting
(assembly/installation)
Engineering Commissioning Operation Decommissioning
Product
phases
Target
groups
Activities
Design engineer
Programmer
Technologist
Process
specialist
Select
Prepare
Design
Construct
Mechanic/
electrician
Unpack
Mount
Install
Programmer
Commissioning engineer
Parameterize
Program
Configure
Simulate
Technologist
Process specialist
Optimize
Test
Machine
operator
Maintenance
technician
Service
Operate
Maintain
Remove
faults
Create
the NC program
Mechanic/
electrician
Disposal company
Dismount
Dispose
Fig. 1-1: Assigning the present documentation to the target groups, product phases and ac-
tivities of the target group
1.2 Purpose
This document instructs the technical staff of the machine manufacturer on how
to perform the mechanical and electrical installation safely and on how to com-
mission the device.
Bosch Rexroth AG
About this documentation
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 1/37

Required qualification: Individual who is able to assess the tasks assigned and
identify possible safety risks owing to qualification in the subject, knowledge
and experience. The individual should also be familiar with the standards and
regulations.
1.3 Availability
This operating instruction applies to all multi-touch operator displays whose
type code starts with "VDPxx.3…".
The type code specifications are located on the type plate of the device. Also re-
fer to chapter 2.1 "Product identification" on page 2.
1.4 Related documents
Title Part number and document type
Rexroth IndraControl
VAP 01
Power Supply unit
R911339613
Operating Instructions
Rexroth IndraControl
VAU 01.1
UPS with Communication Interface
R911336867
Operating Instructions
Rexroth IndraControl
VAC 01
Y-Repeater
R911336973
Operating Instructions
Rexroth IndraControl
V-Devices
Operating Systems
R911343901
Project Planning Manual
Tab. 1-2: Related documents
1.5 Customer feedback
Customer requests, comments or suggestions for improvement are of great im-
portance to us. Please email your feedback on the documentations to Feed-
[e-mail]. Directly insert comments in the elec-
tronic PDF document and send the PDF file to Bosch Rexroth.
2 Product identification and scope of delivery
2.1 Product identification
The type plate is located on the rear side or at the side of the device.
Bosch Rexroth AG
Product identification and scope of delivery
2/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

Bosch Rexroth AG D-64711 Erba ch
Ma de in Ge rma ny
MA6/210-7402-M
U
N
IN 3AC 230V 50/60 Hz
I
N
OUT 10/7,5/5/5/1,5/1,5 A max.
I-C-B-T-V
SW-Vers ion V0,002
MNR: 1070086300 -105 04W03
1070
SN: 123456789
2
3
6
7
7
10 11
12
13
14
9
8
5
4
1
Bosch rexroth Electric Drives and Controls GmbH D-64711 Erbach
VDP16.3DBN-D1-NN-NN
UNDC 24V
N
2A
I-C-B-H-T-V
MNR: R911171013 GM1
FD: 12W27
7261
IND.CONT.EQ 17YB
Front Mounted Type1
SN:008595411
15
Made in Germany
UN : AC 230V/115V,
IN: 2,7A/5A,
MNR: R911171065 -GA1
TYP: VAP01.1H-W23-024-010-NN
Bosch Rexroth Electric Drives and Controls GmbH
D-64711 Erbach
SN: 004012652
7261
IND. CONT-EQ
18WM
I-C-B-H-T-V
FD: 11W40
12
3
4
8
9
5
10
6
12
11
13
15
DC 24V
10,3A
14
I
Made in Germany
1Word mark
2Division or plant number
3Type name (type code)
4Part number
5State of revision
6Date of manufacture (yyWww)
7Nominal voltage
8Nominal current
9Test marking
10 CE mark
11 Underwriters Laboratories Inc. mark
12 Serial number as barcode
13 Serial number
14 Name of origin
15 Company address
Fig. 2-1: Exemplary type plates
2.2 Scope of delivery
●Operator display
●Safety instructions
●Assembling kit
●24 V female connector strip
3 Using safety instructions
3.1 Structure of the safety instructions
The safety instructions are structured as follows:
Bosch Rexroth AG
Using safety instructions
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 3/37

Burns and chemical burns due to wrong
battery treatment!
CAUTION
Safety alert symbol
Signal word
Avoiding danger
Do not open the batteries and do not heat them over 80 °C.
Consequences and
source of danger
Fig. 3-1: Structure of the safety instructions
3.2 Explaining signal words and safety alert symbol
The safety instructions in this documentation contain specific signal words
(danger, warning, caution, notice) and, if necessary, a safety alert symbol
(according to ANSI Z535.6-2006).
The signal word draws attention to the safety instruction and indicates the risk
potential.
The safety alert symbol (triangular safety reflector with exclamation marks),
preceding the signal words Danger, Warning, Caution indicates hazards for
persons.
DANGER
In case of non-compliance with this safety instruction, death or serious injury
will occur.
WARNING
In case of non-compliance with this safety instruction, death or serious injury
can occur.
CAUTION
In case of non-compliance with this safety instruction, minor or moderate injury
can occur.
Bosch Rexroth AG
Using safety instructions
4/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

NOTICE
In case of non-compliance with this safety instruction, material damage can
occur.
3.3 Symbols used
Pointers are displayed as follows:
This is a note.
Tips are displayed as follows:
This is a tip.
3.4 Explaining the signal alert symbol on the device
krax
If this symbol is on your device, you have to observe the documentation
on the device. The respective documentation informs on the type of
hazard as well as the steps required to avoid this hazard.
4 Intended use
The Bosch Rexroth operator displays are passive operator and visualization ter-
minals. They form a PC-based operator terminal when used with a Bosch
Rexroth control cabinet PC.
Risk of damaging the device if not expressly sta-
ted accessories, mounting parts and other com-
ponents, cables, lines and software and firm-
ware are used.
NOTICE
The operator displays may only be used as intended and with the accessories,
mounting parts and other components specified in this documentation. Compo-
nents that are not expressly mentioned must neither be attached nor connected.
The same applies to cables and lines.
Only to be operated with the component configurations and combinations ex-
pressly defined and with the software and firmware specified in the correspond-
ing functional description.
Typical areas of application of the operator display:
Bosch Rexroth AG
Intended use
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 5/37

●Handling and assembly systems
●Packaging and food processing machines
●Printing and paper converting machines
●Machine tools
●Wood processing machines
The operator displays may only be operated under the mounting and installation
conditions, the position and the ambient conditions (temperature, degree of
protection, humidity, EMC etc.) specified in this documentation.
Danger of destruction of the touch screen if op-
erated with inappropriate objects.
NOTICE
Operate the touch screen only with your finger or with a touch pen suitable for
capacitive touch screens.
5 Spare parts, accessories and wear parts
5.1 Y-repeater
Connecting unit to connect two operator displays with the same resolution and
the same version to one control cabinet PC.
Ordering code Part number Description
VAC01.1S-YD1-TCES R911172852 Y-repeater for CDI interface
Tab. 5-1: Y-repeater
5.2 External 24 V power supply unit
Ordering code Part number Description
VAP01.1H-W23-024-010-NN R911171065 External 24 V power supply unit for the
IndraControl V devices
Tab. 5-2: External 24 V power supply unit for the operator display
5.3 Uninterruptible power supply (UPS)
Ordering code Part number Description
VAU01.1U-024-024-240-NN R911171024 Uninterruptible power supply
DC 24 V, 240 watts with USB interface
Tab. 5-3: Uninterruptible power supply (UPS)
Bosch Rexroth AG
Spare parts, accessories and wear parts
6/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

5.4 Connecting cables for CDI interface
Malfunctions caused by using inappropriate CDI cables.
Use only cables listed in the following.
Ordering code Part number Description
RKB0008/000,5 (*******-*******-*******) R911171484 Length: 0.5 m
RKB0008/001,0 (*******-*******-*******) R911171485 Length: 1 m
RKB0008/002,5 (*******-*******-*******) R911170151 Length: 2.5 m
RKB0008/005,0 (*******-*******-*******) R911170152 Length: 5 m
RKB0008/007,5 (*******-*******-*******) R911172971 Length: 7.5 m
RKB0008/010,0 (*******-*******-*******) R911170153 Length: 10 m
RKB0008/015,0 (*******-*******-*******) R911171183 Length: 15 m
RKB0008/020,0 (*******-*******-*******) R911171184 Length: 20 m
RKB0008/025,0 (*******-*******-*******) R911170154 Length: 25 m
RKB0008/030,0 (*******-*******-*******) R911171381 Length: 30 m
RKB0008/035,0 (*******-*******-*******) R911171369 Length: 35 m
RKB0008/040,0 (*******-*******-*******) R911171382 Length: 40 m
RKB0008/050,0 (*******-*******-*******) R911171383 Length: 50 m
RKB0008/055,0 (*******-*******-*******) R911173779 Length: 55 m
RKB0008/060,0 (*******-*******-*******) R911173780 Length: 60 m
RKB0008/065,0 (*******-*******-*******) R911173781 Length: 65 m
RKB0008/070,0 (*******-*******-*******) R911173782 Length: 70 m
Tab. 5-4: CDI connecting cable
Further cable lengths are available upon request.
Two cables are always required to establish a connection between
the VxB and the VDP.
5.5 Connecting cables for the USB interface
Ordering code Part number Description
RKB0019/000,5 (*******-*******-*******) R911171165 USB connecting cable,
Length 0.5 m
RKB0019/001,0 (*******-*******-*******) R911171166 USB connecting cable,
Length 1 m
Bosch Rexroth AG
Spare parts, accessories and wear parts
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 7/37

Ordering code Part number Description
RKB0019/003,0 (*******-*******-*******) R911171167 USB connecting cable,
Length 3 m
RKB0019/005,0 (*******-*******-*******) R911171168 USB connecting cable,
Length 5 m
Tab. 5-5: Connecting cables to the control cabinet PC
5.6 Wear parts
Wear parts are not subject to any warranty.
Backlight
The service life of the backlight is limited. After this period, the backlight will
produce only 50 % of its original brightness. The service life is 50,000 hours if
the ambient temperature is 25 °C.
6 Ambient conditions
In operation Transport Storage
Max. ambient tempera-
ture
+0 °C to +50 °C -20 °C to +60 °C -20 °C to +60 °C
Max. temperature gradi-
ent
Temporal temperature
changes up to 3 K per
minute
Temporal temperature
changes up to 3 K per
minute
Temporal temperature
changes up to 3 K per
minute
Humidity Min. relative humidity:
5 %
Max. relative humidity:
85 %
Min. absolute humidity:
1 g/m3
Max. absolute humidity:
25 g/m3
Condensation not al-
lowed
Corresponds to climatic
class 3K3 acc. to EN
60721-3-3
Min. relative humidity:
5 %
Max. relative humidity:
75 %
Min. absolute humidity:
1 g/m3
Max. absolute humidity:
25 g/m3
Condensation not al-
lowed
Corresponds to climatic
class 2K2 acc. to EN
60721-3-2
Min. relative humidity:
5 %
Max. relative humidity:
85 %
Min. absolute humidity:
1 g/m3
Max. absolute humidity:
25 g/m3
Condensation not al-
lowed
Corresponds to climatic
class 1K2 acc. to EN
60721-3-1
Air pressure Up to 3,000 m above
sea level acc. to EN
61131-2
Up to 3,000 m above
sea level acc. to EN
61131-2
Up to 3,000 m above
sea level acc. to EN
61131-2
Bosch Rexroth AG
Ambient conditions
8/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

In operation Transport Storage
Mechanical strength Max. vibration:
Frequency range: 10…
150 Hz
Excursion: 0.075 mm at
10…57 Hz
Acceleration: 1 g at
57...150 Hz
Acc. to EN 600068-2-6
Max. shock:
15 g 11 ms
Acc. to EN 60068-2-27,
No malfunction
Max. shock:
15 g 11 ms
Acc. to EN 60068-2-27,
No malfunction
Contamination level 2 2 2
Overvoltage category 2 - -
Tab. 6-1: Ambient conditions
Defective product due to gases jeopardizing
functions
NOTICE
Due to the risk of corrosion, avoid sulphurous gases (e.g. sulphur dioxide (SO2)
and hydrogen suphide (H2S)). The product is not resistant against these gases.
Failure of the product due to contaminated air
NOTICE
●The ambient air must not contain acids, alkaline solutions, corrosive agents,
salts, metal vapors and other electrically conductive contaminants in high
concentrations
●The devices to be installed into the housing and installation compartments
must at least comply with the degree of protection IP 54 according to DIN EN
60529.
●The device shall be provided in a suitable fire enclosure in the end-use appli-
cation.
Bosch Rexroth AG
Ambient conditions
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 9/37

7 Technical data
7.1 General technical data
VDP 15.3GA
(Rexroth design)
VDP 15.3CL
(Rexroth design)
VDP 18.3GBN
(Rexroth design)
VDP 21.3GC
(Rexroth design)
VDP 21.3CN
(Rexroth design)
Display 396 mm TFT (15")
1366 × 768 pixels
16.7 million colors
470 mm TFT (18")
1366 × 768 pixels
16.7 million colors
546 mm TFT (21")
1920 × 1080 pixels
16.7 million colors
Operation Multi touch
Surface of the
front panel
Thermally tempered glass
Degree of protection Front panel IP 65 acc. to DIN EN 60 529
Front Type 1 acc. to NEMA (UL)
Rear side IP 20
Voltage supply 24 V DC (use a 24 V power supply unit acc. to DIN EN 60742, classification
VDE 0551, for example the VAP01.1H-W23-024-010-NN, part number
R911171065)
Current consumption Approx. 1 A Approx. 1 A Approx. 1.5 A
Power loss Approx. 24 W Approx. 24 W Approx. 36 W
USB Per USB port max. 500 mA, total current at all USB ports max. 1 A
Weight Approx. 4.8 kg Approx. 6.5 kg Approx. 7.4 kg
Tab. 7-1: Technical data of the VDP 15.3, VDP 18.3 and VDP 21.3
7.2 Optical characteristic values
7.2.1 TFT
The maximum permissible number and type of pixel errors of TFT displays de-
pends on the manufacturer and is defined by the respective "incoming inspec-
tion" of the vendor. This "incoming inspection" is provided by the Bosch Rexroth
service if required.
The maximum brightness and color characteristics of TFT displays depends on
the manufacturer and is defined by the respective specification of the manufac-
turer.
7.2.2 Input system (multi-touch front)
The maximum permissible number and type of defects on the front or the glass,
such as trapped dust, scratches, etc. is defined in the FT1) . The VDP multi-touch
devices meet the quality guideline.
Bosch Rexroth AG
Technical data
10/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

8 Standards
The products have been developed according to the German edition of the
standards published at the time of product engineering.
8.1 Standards used
Standard Description
EN 60 204-1 Safety of machinery - Electrical equipment of machines
EN 61 000-6-4 Generic standards - Emission standard (industrial environ-
ments)
EN 61 000-6-2 Generic standards – Noise immunity (industrial environments)
EN 61 558-2-6 Transformer for 24 V power supply unit, safe separation
EN 60 664-1 Overvoltage category II
EN 61 131-2 24 V output requirements
EN 61 131-2 24 V current supply requirements
EN 60 529 Degrees of protection (including housings and installation com-
partments)
EN 60 068-2-6 Vibration test
EN 60 068-2-27 Shock test
EN 60 721-3-1 and EN 60 721-3-3 Climatic class
Tab. 8-1: Standards used
8.2 CE marking
8.2.1 Declaration of conformity
The electronic products described in the present operating instructions comply
with the requirements and the target of the following EU directive and with the
following harmonized European standards:
EMC directive 2004/108/EC (valid until 04/19/2016)
EMC directive 2014/30/EU (valid from 04/20/2016)
The electronic products described in the present operating instructions are in-
tended for use in industrial environments and comply with the following require-
ments:
1) Quality standard (version December 2013) of the Fachgemeinschaft Eingabesysteme (German
association for input systems)
Bosch Rexroth AG
Standards
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 11/37

Standard Title Edition
DIN EN 61000-6-4 Electromagnetic compatibility (EMC)
Part 6-4: Generic standards – Emission standard for indus-
trial environments (EN 61000-6-4: 2007 + A1:2011)
September 2011
IEC 61000-6-2 Electromagnetic compatibility (EMC)
Part 6-2: Generic standards – Immunity for industrial envi-
ronments (EN 61000-6-2:2005)
2006 + B1:2011
Tab. 8-2: Standards for electromagnetic compatibility (EMC)
Loss of CE conformity due to modifications at the device.
CE marking applies only to the device upon delivery. After modifying
the device, verify the CE conformity.
8.3 UL/CSA certified
The devices are certified acc. to
●UL508 (Industrial Control Equipment) and
●C22.2 no. 142-M1987 (CSA)
UL file no. E210730
However, there can be combinations or extension stages with a limited or miss-
ing certification. Thus, verify the registration according to the UL marking on the
device.
Loss of UL/CSA conformity due to modifications at the device.
UL and CSA marking applies only to the device upon delivery. After
modifying the device, verify the UL and the CSA conformity.
9 Interfaces
9.1 View
1 2 3 4 5 6 7
Fig. 9-1: Interfaces at the operator display
Bosch Rexroth AG
Interfaces
12/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P

9.2 Overview
Name at the
housing
Connection type Connector type, inte-
grated
Mating connector or
cable (from outside)
①S1 Refer to chapter 9.4 "S1 DIP switch" on page 14
②XVID CDI interface, image RJ45 socket RJ45 plug
③XSER CDI interface, data RJ45 socket RJ45 plug
④XUSB1/2 2 USB interfaces USB socket,
4-pin, type A
USB plug,
4-pin, type A
⑤XUSBIN USB2.0 connection to the control
cabinet PC. Maximum length 5 m
Use only one high-speed USB 2.0
cable (refer to chapter 5.5 "Con-
necting cables for the USB inter-
face" on page 7)
USB socket,
4-pin, type B
USB plug,
4-pin, type B
⑥X1S1 24 V DC voltage supply 3-pin, MC1,5/3-
G-3,5 THT
3-pin, FK-MCP 1,5/3-
ST-3,5
⑦Functional earth (FE) M5 Ring cable lug
Tab. 9-1: Interfaces
Malfunctions due to insufficient shielding!
NOTICE
Use only shielded cables and metallic or conductive connector/coupling covers
with large-area shield support.
9.3 24 V DC voltage supply
Fig. 9-2: Interface for 24 V voltage supply
Pin Function
1 +24 V supply voltage
2 0 V supply voltage
3 n.c.
Bosch Rexroth AG
Interfaces
DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P 13/37

Use a 24 V industrial power supply unit acc. to DIN EN 60742, classification VDE
0551, for example "VAP01.1H-W23-024-010-NN" (part number R911171065) for
the voltage supply.
9.4 S1 DIP switch
9.4.1 Overview
S1
1 2
ON
OFF
Fig. 9-3: S1 DIP switch at the connector panel of the operator display
Name at the hous-
ing
Switch type Function
S1/1 DIP switch No function
S1/2 DIP switch OFF: Cable length to control cabinet PC ≤ 30 m
ON: Cable length to control cabinet PC > 30 m
Tab. 9-2: DIP switch at the VDP
9.5 USB interfaces
There are two USB interfaces on the connector panel (XUSB1/2) at the devices
and, depending on the variant, one interface on the front panel.
9.5.1 Operating USB ports at operator display
Cable length of the
XSER connection
DIP switch 2 USB speed Note
Up to 5 meters OFF 12 Mb/s -
Up to 5 meters OFF 480 Mb/s
(USB2.0)
An additional USB cable between con-
trol cabinet PC and XUSBIN is required
From 5 to 30 meters OFF 12 Mb/s The connected device may not contain a
USB hub
More than 30 meters ON 12 Mb/s Only mouse and keyboard can be con-
nected. The connected device may not
contain a USB hub
Tab. 9-3: USB speed depends on XSER cable length
Interference-free USB2.0 connection only up to a cable length of 5
meters.
Bosch Rexroth AG
Interfaces
14/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P