Bosch Rexroth IndraControl VDP 15.3 User manual

Operating Instructions
Electric Drives
and Controls Pneumatics Service
Linear Motion and
Assembly Technologies
Hydraulics
Rexroth IndraControl
VDP 15.3, 18.3, 21.3 Multitouch
Operator Display – Built-In Devices
R911341191
Edition 02

Bosch Rexroth AG VDP 15.3, 18.3, 21.3 Multitouch
Record of Revision
Edition Release Date Notes
First edition 10.2013 --
Edition 02 03.2014 Revision
Copyright
© Bosch Rexroth AG 2014
This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
duced or given to third parties without its consent.
Liability
The specified data is intended for product description purposes only and shall
not be deemed to be a guaranteed characteristic unless expressly stipulated in
the contract. All rights are reserved with respect to the content of this docu-
mentation and the availability of the product.
Editorial Department
Development Automation Aystems Control Hardware HB (KaWa/PiGe)
RS-efc79664d5c1106b0a6846a5001b631e-2-en-US-5

Table of Contents Page
1 About this Documentation..................................................................... 1
2 Product Identification and Scope of Delivery........................................ 2
2.1 Product Identification............................................................................ 2
2.2 Scope of Delivery................................................................................... 3
3 Using the Safety Instructions................................................................. 3
3.1 Safety Instructions – Structure.............................................................. 3
3.2 Explaining Signal Words and Safety Alert Symbol................................. 4
3.3 Symbols Used........................................................................................ 5
4 Intended Use.......................................................................................... 5
5 Spare Parts, Accessories and Wear Parts.............................................. 6
5.1 Y-Repeater............................................................................................. 6
5.2 External 24 V Power Supply Unit .......................................................... 6
5.3 Uninterruptible Power Supply (UPS)..................................................... 6
5.4 Connecting Cables for the CDI Interface............................................... 6
5.5 Wear Parts............................................................................................. 7
6 Ambient Conditions............................................................................... 7
7 Technical Data....................................................................................... 9
7.1 General Technical Data.......................................................................... 9
7.2 Optical Characteristic Values................................................................. 9
7.2.1 TFT......................................................................................................... 9
7.2.2 Input System or Multitouch Front.......................................................... 9
8 Standards............................................................................................ 10
8.1 General Information............................................................................. 10
8.2 Used Standards................................................................................... 10
8.3 CE Marking........................................................................................... 10
8.3.1 Declaration of Conformity .................................................................. 10
8.4 UL/CSA Certified................................................................................. 11
9 Interfaces............................................................................................. 12
9.1 View..................................................................................................... 12
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Table of Contents
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P I

Page
9.2 Overview.............................................................................................. 12
9.3 DC 24 V Voltage Supply....................................................................... 13
9.4 S1 DIP Switch...................................................................................... 13
9.4.1 Overview.............................................................................................. 13
9.5 USB Interfaces..................................................................................... 13
9.6 XSER Interfaces and XVID Interfaces................................................... 14
10 Assembly, Disassembly and Electrical Installation.............................. 15
10.1 Housing Dimensions............................................................................ 15
10.1.1 Rexroth Design.................................................................................... 15
10.1.2 Rexroth Special Design........................................................................ 16
10.1.3 Bosch Design....................................................................................... 17
10.2 Installation Notes................................................................................. 17
10.3 Assembly.............................................................................................. 17
10.4 VDP Assembly Dimensions................................................................... 20
10.5 Disassembly......................................................................................... 20
10.6 Electrical Wiring................................................................................... 21
10.6.1 Connecting the Control Cabinet PC to Operating Display................... 21
10.6.2 Connecting the OperatingDisplay to the 24 V Voltage Supply............. 23
10.6.3 Connection Scheme – Power Supply Unit, UPS, Control Cabinet PC
and Operating Display......................................................................... 24
10.6.4 Recommendation for the Assembly of CDI Cables with Long Lengths
in an Interference-Prone Environment................................................. 24
11 Commissioning.................................................................................... 27
12 Device Description............................................................................... 28
12.1 General Information............................................................................. 28
12.2 Operating and Error Display................................................................ 28
13 Error Causes and Elimination.............................................................. 28
14 Maintenance........................................................................................ 29
14.1 General Information............................................................................. 29
14.2 Display................................................................................................. 29
14.3 Cleaning Notes..................................................................................... 29
14.4 Regular Maintenance Tasks................................................................. 30
15 Ordering Information........................................................................... 30
Bosch Rexroth AG
Table of Contents VDP 15.3, 18.3, 21.3 Multitouch
II DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

Page
15.1 Accessories and Spare Parts............................................................... 30
15.2 Type Code............................................................................................ 31
16 Disposal............................................................................................... 31
16.1 Take-Back............................................................................................. 31
16.2 Packaging............................................................................................. 32
17 Service and Support............................................................................ 32
Index.................................................................................................... 35
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Table of Contents
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P III

Bosch Rexroth AG VDP 15.3, 18.3, 21.3 Multitouch
IV DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

1 About this Documentation
Overview – target groups and product phases
The activities, product phases and target groups that refer to the present docu-
mentation are marked in red color in the following figure.
Example: In the product phase "Mounting (assembly/installation)", the "mechan-
ic/electrician" can execute the activity "install" using this documentation.
Disposal company
Selection Operation
Engineering Commissioning De-
commissioning
To test
To optimize
To create
the NC program
To remove
faults
To maintain
To operate
To simulate
To configure
To program
To parameterize
To install
To mount
To unpack
To construct
To design
To prepare
To select
Design engineer
Mechanic/
electrician)
Process
specialist
Machine
operator
Service
Presales Aftersales
Programmer
Technologist
Product
phases
Target
groups
Activities
Mounting
(assembly/installation)
Programmer
Mechanic/
electrician
To dismount
To dispose
Commissioning engineer
Technologist
Process specialist
Maintenance
technician
Fig. 1-1: Assigning the present documentation to the target groups, product phases and ac-
tivities of the target group
Purpose
This document instructs the technical staff of the machine manufacturer on how
to perform the mechanic and electrical installation in a safe way and on how to
commission the device.
Required qualifications: Individual who is able to assess the tasks assigned and
identify possible safety risks owing to qualification in the subject, knowledge
and experience. The individual should also be familiar with the standards and
regulations.
Scope
This operating instruction is valid for all multitouch operating displays whose
type code starts with "VDPxx.3…".
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
About this Documentation
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 1/37

The type designation code specifications are located on the type plate of the de-
vice, see also chapter 2.1 "Product Identification" on page 2.
Further documents
Title Partnumberanddocumenttype
RexrothIndraControl
VAP01
PowerSupplyUnit
R911339613
OperatingInstructions
RexrothIndraControl
VAU01.1
UPSwithCommunicationInterface
R911336867
OperatingInstructions
RexrothIndraControl
VAC01
Y-Repeater
R911336973
OperatingInstructions
RexrothIndraControl
VDevices
OperatingSystems
R911343901
ProjectPlanningManual
Tab. 1-1: Required and supplementing documentation
Customer feedback
Customer requests, comments or suggestions for improvement are of great im-
portance to us. Please email your feedback on the documentations to Feed-
[email protected]. Directly insert comments in the elec-
tronic PDF document and send the PDF file to Bosch Rexroth.
2 Product Identification and Scope of Delivery
2.1 Product Identification
The type plate is located on the rear panel.
Bosch Rexroth AG
Product Identification and Scope of Delivery VDP 15.3, 18.3, 21.3 Multitouch
2/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

Bosch Rexroth AG D-64711 Erbach
Made in Germany
MA6/210-7402-M
U
N
IN 3AC 230V 50/60 Hz
I
N
OUT 10/7,5/5/5/1,5/1,5 A max.
I-C-B-T-V
SW-Version V0,002
MNR: 1070086300 -105 04W03
1070
SN: 123456789
13026
2
3
6
7
7
10
11
12
13
14
9
8
5
4
1
Bosch rexroth Electric Drives and Controls GmbH
D-64711 Erbach Made in Germany
BTV40.1AHB-256S-P5C-
UN-FW
UNIN 3AC 230V 50760Hz
IN
OUT 10/7,5/5/5/1,5/1,5A max.
I-C-B-T-V
SW-Version V0,002
MNR:1070170021 -101 03W19
7261
IND.CONT.EQ 17YB
SN: 123456814
15
16
MadeinGermany
UN: AC 230V / 115V
IN: 0,7A/ 1,4A
MNR: 1070086255 -101 V-Nr: 1
TYP: PCPNL PEN400J1287 IS110-T
Bosch Rexroth Electric Drives and Controls GmbH
D-64711 Erbach
SN: 004012652
7261
IND.CONT-EQ 17YB
XXXXXXXXXXXXXXXXX
I-C-B-H-T-V
FD: 05W01
123
4
8
9
5
10
6
12
11 13
14
15
16
1Logotype
2Division or plant number
3Type code (type designation code)
4Parts number
5State of revision
6Date of manufacture (yyWww)
7Nominal voltage
8Nominal current
9Test marking
10 Version number
11 CE marking
12 Underwriters Laboratories Inc. mark
13 Serial number as barcode
14 Serial number
15 Designation of origin
16 Company address
Fig. 2-1: Type plates, example
2.2 Scope of Delivery
●Operating display
●Safety instructions
●Mounting kit
●24 V female connector strip
3 Using the Safety Instructions
3.1 Safety Instructions – Structure
The safety instructions are structured as follows:
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Using the Safety Instructions
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 3/37

Burns and chemical burns due to wrong
battery treatment!
CAUTION
Safety alert symbol
Signal word Consequences and
source of danger
Avoiding danger
Do not open the batteries and do not heat them over 80 °C.
Fig. 3-1: Safety instructions – Structure
3.2 Explaining Signal Words and Safety Alert Symbol
The safety instructions in this documentation contain specific signal words (dan-
ger, warning, caution, notice) and, if necessary, a safety alert symbol (according
to ANSI Z535.6-2006).
The signal word is meant to draw the reader's attention to the safety instruction
and signifies the degree of danger.
The safety alert symbol (a triangle with an exclamation point), which precedes
the signal words danger,warning and caution is used to alert the reader to per-
sonal injury hazards.
DANGER
In case of non-compliance with this safety instruction, death or serious injury
will occur.
WARNING
In case of non-compliance with this safety instruction, death or serious injury
can occur.
CAUTION
In case of non-compliance with this safety instruction, minor or moderate injury
could occur.
NOTICE
In case of non-compliance with this safety instruction, property damage could
occur.
Bosch Rexroth AG
Using the Safety Instructions VDP 15.3, 18.3, 21.3 Multitouch
4/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

3.3 Symbols Used
Notes are displayed as follows:
This is a note.
Tips are displayed as follows:
This is a tip.
4 Intended Use
The Bosch Rexroth operator terminals are passive operation and visualization
terminals. They form a PC-based operator terminal when used with a Bosch
Rexroth control cabinet PC.
Danger of destruction of the device if not ex-
pressly stated accessories, mounting parts and
other components, cables, lines, software and
firmware are used.
NOTICE
The operator displays may be used only as intended and with the accessories,
mounting parts and other components specified in this documentation. Compo-
nents that are not expressly mentioned must neither be attached nor connec-
ted. The same is valid for cables and lines.
Operation must only be carried out with the hardware component configura-
tions and combinations that are expressly specified and with the software and
firmware indicated and specified in the respective documentation and function-
al descriptions.
Typical areas of application of the operator displays are:
●Handling systems and assembly systems
●Packaging and food processing machines
●Printing machines and paper converting machines
●Machine tools
●Wood processing machines
The operator displays may only be operated under the mounting and installation
conditions, the position, and the ambient conditions (temperature, degree of
protection, humidity, EMC etc.) specified in this documentation.
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Intended Use
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 5/37

Risk of destroying the touch screen or the front
panel by using inappropriate items.
NOTICE
Operate the touch screen only with your finger or with a special touch pen
(parts number 1070923266).
5 Spare Parts, Accessories and Wear Parts
5.1 Y-Repeater
Connecting unit to connect two operator displays featuring the same resolution
and the same version to one control cabinet PC.
Orderingcode Partnumber Description
VAC01.1S-YD1-TCES R911172852 Y-repeaterforCDIinterface
Tab. 5-1: Y-Repeater
5.2 External 24 V Power Supply Unit
Orderingcode Partnumber Description
VAP01.1H-W23-024-010-NN R911171065 External24Vpowersupplyunitforthe
IndraControlVdevices
Tab. 5-2: External 24 V power supply unit for the operator display
5.3 Uninterruptible Power Supply (UPS)
Orderingcode Partnumber Description
VAU01.1U-024-024-240-NN R911171024 Uninterruptiblepowersupply
DC24V,240wattswithUSBinterface
Tab. 5-3: Uninterruptible power supply (UPS)
5.4 Connecting Cables for the CDI Interface
Malfunctions caused by using inappropriate CDI cables.
Use only cables listed in the following overview.
Orderingcode Partnumber Description
RKB0008/000,5(*******-*******-*******) R911171484 Length:0.5m
RKB0008/001,0(*******-*******-*******) R911171485 Length:1m
RKB0008/002,5(*******-*******-*******) R911170151 Length:2.5m
RKB0008/005,0(*******-*******-*******) R911170152 Length:5m
Bosch Rexroth AG
Spare Parts, Accessories and Wear Parts VDP 15.3, 18.3, 21.3 Multitouch
6/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

Orderingcode Partnumber Description
RKB0008/007,5(*******-*******-*******) R911172971 Length:7.5m
RKB0008/010,0(*******-*******-*******) R911170153 Length:10m
RKB0008/015,0(*******-*******-*******) R911171183 Length:15m
RKB0008/020,0(*******-*******-*******) R911171184 Length:20m
RKB0008/025,0(*******-*******-*******) R911170154 Length:25m
RKB0008/030,0(*******-*******-*******) R911171381 Length:30m
RKB0008/035,0(*******-*******-*******) R911171369 Length:35m
RKB0008/040,0(*******-*******-*******) R911171382 Length:40m
RKB0008/050,0(*******-*******-*******) R911171383 Length:50m
Tab. 5-4: Connecting cables to control cabinet PC, panel PC and operator display
Further cable lengths are available on request.
Two cables are always required to establish a connection between
the VxB and the VDP.
5.5 Wear Parts
Wear parts are not subject to any warranty.
Backlight
The service life of the backlight is limited. After this time has been exceeded,
the backlight will produce only 50 % of its original brightness. The service life is
approx. 50,000 hours at an ambient temperature of 25 °C.
6 Ambient Conditions
Inoperation Transport Storage
Max.ambienttempera-
ture +0℃to+50℃-20℃to+60℃-20℃to+60℃
Max.temperaturegradi-
ent Temporaltemperature changesupto3Kper
minute
Temporaltemperature
changesupto3Kper
minute
Temporaltemperature
changesupto3Kper
minute
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Ambient Conditions
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 7/37

Inoperation Transport Storage
Humidity Min.relativehumidity:
5%
Max.relativehumidity:
85%
Min.absolutehumidity:
1g/m3
Max.absolutehumidity:
25g/m3
Condensationnotal-
lowed
Correspondstoclimatic
class3K3acc.toEN
60721-3-3
Min.relativehumidity:
5%
Max.relativehumidity:
75%
Min.absolutehumidity:
1g/m3
Max.absolutehumidity:
25g/m3
Condensationnotal-
lowed
Correspondstoclimatic
class2K2acc.toEN
60721-3-2
Min.relativehumidity:
5%
Max.relativehumidity:
85%
Min.absolutehumidity:
1g/m3
Max.absolutehumidity:
25g/m3
Condensationnotal-
lowed
Correspondstoclimatic
class1K2acc.toEN
60721-3-1
Airpressure Upto3000mabovesea
levelacc.toEN
61131-2
Upto3000mabovesea
levelacc.toEN
61131-2
Upto3000mabovesea
levelacc.toEN
61131-2
Mechanicalstrength Max.vibration:
Frequencyrange:10Hz
to150Hz
Excursion:0.075mmat
10Hzto57Hz
Acceleration:1gat
57Hzto150Hz
acc.toEN600068-2-6
Max.shock:
15g11ms
acc.toEN60068-2-27,
nodisturbanceofthe
function
Max.shock:
15g11ms
acc.toEN60068-2-27,
nodisturbanceofthe
function
Contaminationlevel 2 2 2
Overvoltagecategory 2 - -
Tab. 6-1: Ambient conditions
The ambient air must not contain acids, alkaline solutions, corrosive
agents, salts, metal vapours, and other electrically conductive con-
taminants in high concentrations.
The ambient air must be dust-free. Housing and installation compart-
ments must at least comply with degree of protection IP 54 accord-
ing to DIN VDE 0470-1.
Bosch Rexroth AG
Ambient Conditions VDP 15.3, 18.3, 21.3 Multitouch
8/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

7 Technical Data
7.1 General Technical Data
VDP15.3GA
(Rexrothdesign)
VDP15.3CL
(Boschdesign)
VDP18.3GBN
(Rexrothdesign) VDP21.3GC (Rexrothdesign)
VDP21.3CN
(Boschdesign)
Display 396mmTFT(15")
1366×768pixels
16.7millioncolors
470mmTFT(18")
1366×768pixels
16.7millioncolors
546mmTFT(21")
1920×1080pixels
16.7millioncolors
Operation Multitouch
Surfaceofthe
frontpanel Thermallytemperedglass
Enclosurerating FrontpanelIP65accordingtoDINEN60529
Fronttype1accordingtoNEMA(UL)
RearpanelIP20
Voltagesupply DC24V(usea24VpowersupplyunitaccordingtoDINEN60742,classifi-
cationVDE0551,forexampletheVAP01.1H-W23-024-010-NN,partnum-
berR911171065)
Currentconsumption Approx.1A Approx.1A Approx.1.5A
Powerloss Approx.24W Approx.24W Approx.36W
USB PerUSBportmax.500mA,totalcurrentatallUSBportsismax.1A.
Weight Approx.4.8kg Approx.6.5kg Approx.7.4kg
Tab. 7-1: Technical data of the VDP 15.3, VDP 18.3 and VDP 21.3
7.2 Optical Characteristic Values
7.2.1 TFT
The maximum permissible number and type of pixel errors of TFT displays de-
pends on the manufacturer and is defined by the the respective "Incoming In-
spection" of the manufacturer.
7.2.2 Input System or Multitouch Front
The maximum permissible number and type of defects on the front or the glass,
such as trapped dust, scratches, etc. is defined in the FT quality standard (ver-
sion December 2013) of the Fachgemeinschaft Eingabesysteme (German associ-
ation for input systems).
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Technical Data
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 9/37

8 Standards
8.1 General Information
The products have been developed according to the current German edition of
the standards at the time of product development.
8.2 Used Standards
Standard Meaning
EN60,204-1 Safetyofmachinery-Electricalequipmentofmachines
EN61,000-6-4 Genericstandards-emissionstandard(industrialenvironments)
EN61,000-6-2 Genericstandards–noiseimmunity(industrialenvironments)
EN61,558-2-6 Transformerfor24Vpowersupplyunit,protectiveseparation
EN60,664-1 OvervoltagecategoryII
EN61,131-2 24Voutputsrequirements
EN61,131-2 24Vcurrentsupplyrequirements
EN60529 Degreesofprotection(includinghousingsandinstallationcom-
partments)
EN60,068-2-6 Vibrationtest
EN60,068-2-27 Shocktest
EN60721-3-1and
EN60,721-3-3 Climaticclass
Tab. 8-1: Used standards
8.3 CE Marking
8.3.1 Declaration of Conformity
The electronic products that are described in the present instructions, comply
with the requirements and the target of the following EU directive and with the
following harmonized European standards:
EMC Directive 2004/108/EC
The electronic products described in the present instructions are intended for
use in industrial environments and comply with the following requirements:
Bosch Rexroth AG
Standards VDP 15.3, 18.3, 21.3 Multitouch
10/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

Standard Title Edition
DINEN61000-6-4
(VDE0839-6-4) ElectromagneticCompatibility(EMC) Part:6-4:Genericstandards–emissionstandardforindus-
trialenvironments(IEC61000-6-4:2006)
September2007
DINEN61000-6-2
(VDE0839-6-2) ElectromagneticCompatibility(EMC) Part:6-2:Genericstandards–noiseimmunityforindustrial
environments(IEC61000-6-2:2005)
March2006
Tab. 8-2: Standards for electromagnetic compatibility (EMC)
Non-compliance with CE conformity due to modifications to the de-
vice.
The CE marking is only valid for the device in its delivery status. Af-
ter having modified the device, the CE conformity is to be verified.
8.4 UL/CSA Certified
The devices are certified according to
●UL508 (Industrial Control Equipment) and
●C22.2 No. 142-M1987 (CSA)
UL file no. E210730
However, there can be combinations or extension stages with limited or missing
certification. Thus, verify the registration according to the UL marking on the de-
vice.
Loss of UL/CSA conformity due to modifications to the device.
The UL and CSA marking is only valid for the device in its delivery
status. After modifying the device, the UL and CSA conformity is to
be verified.
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Standards
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 11/37

9 Interfaces
9.1 View
1 2 3 4 5 6 7
Fig. 9-1: Interfaces on the operating display
9.2 Overview
Designationat
thehousing Connectiontype Connectortype,inte- grated Matingconnectoror cable(fromoutside)
①S1 Seechapter9.4 "S1DIPSwitch"onpage13
②XVID CDIinterface,screen RJ45femaleconnec-
tor RJ45connector
③XSER CDIinterface,data RJ45femaleconnec-
tor RJ45connector
④XUSB1/2 2USBinterfaces USBfemaleconnec-
tor,
4-pin,typeA
USBconnector,
4-pin,typeA
⑤XUSBIN USB2.0connectiontothecontrol
cabinetPC.Maximumlength5m
Useonlyahigh-speedUSB2.0ca-
ble(seechapter5 "SpareParts,
AccessoriesandWearParts"on
page6)
USBfemaleconnec-
tor,
4-pin,typeB
USBconnector,
4-pin,typeB
⑥X1S1 DC-24-Vvoltagesupply 3-pin,MC1,5/3-
G-3,5THT 3-pin,FK-MCP1,5/3- ST-3,5
⑦Functionalearthground(FE) M5 Ringcablelug
Tab. 9-1: Interfaces
Malfunctions due to insufficient shielding!
NOTICE
Use only shielded cables and metallic or conductive connector/coupling covers
with large-area shield support.
Bosch Rexroth AG
Interfaces VDP 15.3, 18.3, 21.3 Multitouch
12/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

9.3 DC 24 V Voltage Supply
Fig. 9-2: Interface for 24 V voltage supply
Pin Function
1 Supplyvoltage+24V
2 Supplyvoltage0V
3 n.c.
Use a 24 V industrial power supply unit acc. to DIN EN 60742, classification VDE
0551, for example "VAP01.1H-W23-024-010-NN" (parts number R911171065) for
the voltage supply.
9.4 S1 DIP Switch
9.4.1 Overview
S1
1 2
Fig. 9-3: S1 DIP switch on the connector panel of the operating display
Designationatthe
housing Switchtype Function
S1/1 DIPswitch Nofunction
S1/2 DIPswitch OFF:CablelengthtothecontrolcabinetPC≤30m
ON:CablelengthtothecontrolcabinetPC>30m
Tab. 9-2: DIP switch at the VDP
9.5 USB Interfaces
The devices feature two USB interfaces on the connector panel (XUSB1/2), and,
depending on the version, one interface on the front panel.
VDP 15.3, 18.3, 21.3 Multitouch Bosch Rexroth AG
Interfaces
DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P 13/37

Operation of the USB ports on the operating display
The USB speed at the operating display depends on the cable length of the
XSER connection and of the DIP switch setting, see tab. 9-3 "USB speeds de-
pending on the XSER cable length" on page 14:
Cablelengthofthe
XSERconnection DIPswitch2 USBspeed Note
Upto5meters OFF 12Mb/s -
Upto5meters OFF 480Mb/s
(USB2.0) AnadditionalUSBcablebetweencon-
trolcabinetPCandXUSBINisrequired
From5to30meters OFF 12Mb/s Makesurethattheconnecteddevice
doesnotcontainaUSBhub
Longerthan30me-
ters ON 12Mb/s Onlyamouseandkeyboardscanbe connected.Makesurethattheconnec-
teddevicedoesnotcontainaUSBhub
Tab. 9-3: USB speeds depending on the XSER cable length
Interference-free USB2.0 connection is possible up to a cable length
of 5 meters only.
Connect only USB devices that meet the USB2.0 specification.
The cables of the connected USB devices have to comply with the
USB2.0 specifications.
If the total current of all USB ports exceeds 1 A and switches the
power supply unit of the operating display off.
9.6 XSER Interfaces and XVID Interfaces
CDI interface
The CDI interface is assigned to the two RJ45 female connectors XSER and
XVID. The connection between the control cabinet PC and the operating display
is established on these female connectors via two ready-made cables available
as accessory, see chapter 5 "Spare Parts, Accessories and Wear Parts" on page
6.
The CDI interface includes the data interface (XSER) as well as the screen inter-
face (XVID).
XVID and XSER Markings
The CDI interfaces are color-coded on the device:
Bosch Rexroth AG
Interfaces VDP 15.3, 18.3, 21.3 Multitouch
14/37 DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P