Boser BPC-9215-F02 User manual

BPC-9215-F02
15” High Speed Panel PC
with Touch Screen, Atom™ N550,
2 COM, 6 USB2.0, 180W ATX P/S

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2011 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.0, March 02, 2011

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 2
1.3 Dimensions ............................................................................ 4
Chapter 2 Unpacking ..................................................5
Chapter 3 Hardware Installation ..............................7
3.1 Install SBC.............................................................................. 7
3.2 Install Hard Disk Driver......................................................... 8
3.3 Install Back Cover ................................................................. 9
3.4 Wall-Mount Kit ..................................................................... 10
Chapter 4 SBC Installation ......................................11
4.1 Before Installation ............................................................... 11
4.2 Board Layout ....................................................................... 12
4.3 Jumper List .......................................................................... 13
4.4 Connector List ..................................................................... 14
4.5 Configuring the CPU ........................................................... 14
4.6 System Memory ................................................................... 15
4.7 VGA Controller .................................................................... 15
4.8 Serial ATA Connector ......................................................... 16
4.9 Serial Port Connectors ....................................................... 17
4.10 USB Port............................................................................... 18
4.11 CMOS Data Clear................................................................. 18
4.12 System Front Panel Control ............................................... 19
4.13 Fan Connectors ................................................................... 20
4.14 Audio Connectors ............................................................... 20
4.15 Mini PCIe Connector ........................................................... 21
4.16 8-bit GPIO Function............................................................. 21

Chapter 5 AMI BIOS Setup.....................................23
5.1 Starting Setup...................................................................... 23
5.2 Using Setup ......................................................................... 24
5.3 Main Menu............................................................................ 25
4.4 Advanced Settings .............................................................. 25
4.5 Advanced Chipset Features............................................... 26
4.6 Integrated Peripherals ........................................................ 27
4.7 Power Management Setup ................................................. 28
4.8 PnP/PCI Configurations...................................................... 29
4.9 PC Health Status ................................................................. 29
Chapter 6 Driver Installation................................... 31
6.1 Chipset Driver Installation.................................................. 31
6.2 VGA Driver Installation ....................................................... 34
6.3 LAN Driver Installation........................................................ 37
6.4 Audio Driver Installation..................................................... 39
6.5 Touch Screen Driver Installation ....................................... 42

Declaration of Conformity -- CE Mark
BOSER Technology hereby acknowledges that compliance testing in
accordance with applicable standards of the EU’s EMC Directive,
89/336/EEC, was successfully completed on a sample of the equipment
identified below:
Equipment Class: Information Technology Equipment
Product Model Series: BPC-9215-F02
This Product Complies With: EN55022: Class A for Radiated emissions
EN50082-2: Heavy Industrial EMC Immunity
We, the undersigned, hereby declare that the equipment specified above
conforms to the above directives and standards.
Manufacturer:
BOSER TECHNOLOGY CO., LTD.

Safety Instructions
The safety recommendations outlined in this section are to be read,
understood and followed before operating the product. Keep this
information in a safe place for future reference. Failure to comply with any
of the following safety procedures could result in serious hazard.
Do not operate product for any purposes other than its intended use
This product is intended for indoor use only
Do not operate product if power cord is damaged in anyway
Do not insert objects into openings
Do not immerse product in water or permit liquids to spill inside
Turn off power when unattended or not in use. Unplug product before
moving it or when it is not in use for an extended period of time. The
socket-outlet shall be installed near the equipment and shall be easily
accessible
Do not alter or extend electric plug. Plug is configured for appropriate
electrical supply
Do not overload electrical outlets beyond their capacity as this can result in a
fire
NOTE: DO NOT TOUCH THE PRODUCT OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.

Life Expectancy of Constituent Parts
This section describes the life expectancy of constituent parts (backlight,
power supply, internal cooling fan and touch screen) which make up to
BPC-9215-F02.
TFT Display Backlight
Display brightness decreases over time with use. The expected operating
lifetime of the backlight time to reach 50% initial brightness) is 30,000 hours
(assuming continuous lit state at 25 degrees C). Actual lifetime before
replacement is about 30,000 hours, although this depends on operating
conditions.
Touch Screen
The operating lifetime of the touch screen is approximately 1 million
operations (as tested by mechanical manipulation under 100g of force at a
rate of two presses per second)

1
Chapter 1
General Description
The BPC-9215-F02 is a 15” industrial grade Panel PC which comes
with a TFT color panel display. The rear design of the BPC-9215-F02
enhances the disassembly process when required. It also supports
various mounting solutions like wallmount, or desktop for different
application.
The BPC-9215-F02 has a 15” display and touch screen that operate
under all types of working environments.
zThe BPC-9215-F02 is IBM PC/AT compatible and can be
drawn from a large body of hardware.
zThe BPC-9215-F02 features an all-in-one flat display.
zKeyboard less operations are possible through the use
of a touch screen. A watchdog timer is indispensable in
Failure Analysis applications.
You can select from a broad range of variations to arrive at the
optimum configuration for your application and budget

2
1.1 Major Features
The BPC-9215-F02 series comes with the following features:
¾Aluminum front panel design
¾15” TFT color panel display w/touch screen
¾Intel® Atom™ N550 processor
¾VGA, dual Gigabit Ethernet (option for 3), Audio port
¾1 x 2.5” SATA HDD space
¾2 x COM port, 6 x USB2.0 port
¾1 x mini PCIe socket
¾180W ATX P/S
¾2 x 4cm ball bearing cooling fan
¾Option for Wireless LAN module, open frame type
1.2 Specifications
zSystem
SBC Model
HS-1754A
CPU
Intel® Atom™ Dual-Core N550 processor 1.5GHz (45nm,
667MHz FSB, 512KB*2 L2 Cache)
BIOS
Award 8MB DIP-SPI Flash BIOS
System Chipset:
Intel® NM10
System Memory
2 x 204-pin SO-DIMM socket DDR3 1333MHz up to 2GB
Display
Intel® GMA3150 Graphics Core (DVMT Max. 384MB)
Audio
VIA VT1705 HD Audio Core with 6-Channel
Ethernet
Dual RealTek RTL8111E 10/100/1000 Mbps LAN
RealTek RTL8110C 10/100/1000 Mbps LAN (option)
Provides Wireless LAN Module (option)
Storage
1 x 2.5” SATA HDD space
Expansion Interface
1 x Mini PCIe socket

3
zPanel & Touch Screen
LCD Size
15”
Max Resolution
1024(H) x 768(V) pixels RGB strip arrangement
Brightness (cd/m2)
300 (center 1 points Typ.)
LCD Color
16.7M colors (6-bits with A-FRC)
Pixel Pitch (mm)
0.297 x 0.297
Touch Screen
15” resistive
zMechanical & Environmental
Thermal System
2 x 4cm ball bearing cooling fan
Dimensions (LxHxW)
41.5 x 32.0 x 8.37 cm
Cut Out Size (LxH)
36.4 x 26.7 cm
Operation/Storage Temperature
0~+50 degrees C /-20~+70 degrees C
EMC
FCC/CE
Front Panel Protection
IP65 compliance
Power Supply
100~240V AC, 180W ATX power supply
zI/O Interface
Rear I/O

4
1.3 Dimensions

5
Chapter 2
Unpacking
After unpacking the Panel PC, place it on a raised surface and carefully
inspect the Panel PC for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
The BPC-9215-F02 delivery package contains the following items:
BPC-9215-F02 x 1 w/Power Cable x 1
Utility CD Disk x 1, including User’s Manual x 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

6
This page intentionally left blank.

7
Chapter 3
Hardware Installation
This chapter tells how to install components into the Panel PC system.
External interface please refers to system board’s manual.
3.1 Install SBC
1. Follow the photo instruction install the SBC onto the chassis.

8
3.2 Install Hard Disk Driver
1. Follow the photo instruction install the HDD onto the HDD
mounting bracket.
2. Follow the photo instruction install the HDD_KIT onto the
chassis.

9
3.3 Install Back Cover
1. Follow the photo instruction install the back cover onto the
chassis.

10
3.4 Wall-Mount Kit

11
Chapter 4
SBC Installation
This chapter provides the information on how to install the hardware
using the HS-1754A. This chapter also contains information related to
jumper settings of switch, and watchdog timer selection etc.
4.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (JBAT Îopen)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.

12
4.2 Board Layout