SAFETY INSTRUCTIONS
m IMPORTANT READ CAREFULLY: It is important that all operators read and understand all
sections of this Tool Technical Data manual and the separate Safety and Operating Instruction
Manual which come with this tool. Failure to do so could result in you or others in the working
area to be seriously injured.
m WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined
in EN166 should be used. However all aspects of operators work, environment and other type/s of machinery
being used, should also be considered when selecting any personal protection equipment. Note: Non-side
shielded spectacles and face shields alone do not provide adequate protection.
m WARNING! To prevent accidental injuries:
• Never place a hand or any other part of the body in fastener discharge area of tool.
• Never point tool at yourself or anyone whether it contains fasteners or not.
• Never engage in horseplay.
• Never pull the trigger unless the nose is directed towards the work.
• Always handle the tool with care.
• Use the Bostitch tool only for the purpose for which it was designed, such as: the finishing around doors,
windows and edging; draw bottoms, cabinet backs and cabinet making; picture framing and furniture trim.
These tools should not be used for anything other than wood to wood applications.
• Do not pull the trigger or depress the work safety yoke whilst loading the tool.
• To prevent accidental actuation and possible injury, always disconnect air supply.
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
• Read the additional Safety & Operating instructions booklet before using tool.
• Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
• The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
• N62FNB & DA1564K ONLY: In observance of European Directives 2002/96/EC & 2006//66/EC on waste
electrical and electronic equipment/batteries and their national implementations, electric tools/
batteries that have reached the end of their life must be collected separately and returned to an
approved recycling facility.
• Avoid dangerous environments. Do not expose the tools to rain, damp or wet conditions.
• Never disassemble the LED unit.
• Do not dispose of the LED unit / battery in fire. If the battery is burnt, it may explode.
LOADING
m Warning! When loading the tool 1) Never place a hand or any part of the body in fastener discharge area of
the tool; 2) Never point the tool at self or anyone else; 3) Do not pull the trigger or depress the safety yoke as
accidental actuation may occur, possibly causing injury.
The N62FNB / N62FNSP / DA1564K nailers are equipped with dual load purpose magazines. Nails can be loaded
in either method.
LOAD AND PULL PUSHER
1. Load nails through the slot in the rear of the magazine and past retaining clip. (Fig 1)
2. Pull pusher back behind nail stick and release. (Fig 2)
3. Ensure magazine pusher is behind the last nail stick. (Fig 3)
PULL PUSHER TO LOCK BACK AND LOAD
1. Pull pusher back until it is locked at the end of magazine. (Fig 4)
2. Load nails through the slot in the rear of the magazine and past retaining clip. (Fig 5)
3. Press the pusher button to release and allow the pusher to push behind the nails. (Fig 6)
4. Blow the magazine clean periodically to keep the pusher moving smoothly and to keep dirt and debris out of
the nail channel.
GB
© Stanley Bostitch
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται ηαναπαραγωγή χωρίς προηγούμενη άδεια. Τα μηεξουσιοδοτημένα αντίγραφα του παρόντος
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może byćkopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowiądeklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może byćkopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowiądeklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizatăeste interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
