Boyo VTCRH2 User manual

VTCRH4
VTCRH1 VTCRH2

1. Product Function & Parameter
Attention
For your safety, Do not watch video or set monitors while driving.
Non-professional please do not disassemble the product at will,
please consult the after-sales service organization when the
product malfunctions, or send it to the local maintenance
department for inspection and repair.
Warning
When installing this product, please install it in the position permitted
by laws and regulations, and we shall not be responsible for the
liability caused by the illegal installation of the product.
Tips
In cold weather, the product may appear dark screen phenomenon
when startup. Which will heat up slowly and return to normal with the
increase of temperature.
1
Wireless Monitor
• LCD: 5 inch IPS panel, 16:9 high definition
• Resolution: 1024*RGB*800
• Full viewing angle: Left(85°) Right(85°) Below(85°) Above(85°)
• Panel key function: 5PCS key control
• Wireless video input: 1, 2, or 4 channel wireless video input
• Using digital wireless encryption technology to code connection,
with strong anti-interference ability
• 2.4G wireless transmission distance: 700ft. in open area
• Power supply: DC12-24V
• Power consumption: 3W
• Working temperature: -4°F ~ 158°F
• Storage temperature: -22°F ~ 185°F
• Size: 5.6" x 4.1" x 2.5" (excluding bracket)
Wireless Camera
2
• Effective resolution: 1280*720px, 720P,
• Image Sensor: 1/2.7" CMOS
• Horizontal viewing angle: 130 degree
• Wireless transmission distance: 700ft. in open area
• System: PAL/NTSC automatically
• SPSP: FHSS(adaptive frequency hopping)
• Transmission bandwidth: 8MHz BER<1E-3
• Built-in battery capacity: 6400mA
• Battery indicator: 4 LED lights
• Battery charging time: DC5.5, 5~24V, 10 hours
• Working time: 18 hours(when fully charged)
• Camera adjustable angle: 0-100 degree
• Operation frequency: 2400-2483.5MHZ
• ON/OFF mode: press and hold to turn on and turn off, short press to
display battery capacity
• Installation mode: magnet base adsorption installation
• Night vision: HD infrared night vision
• SNR: 46.5dB
• Waterproof level: IP68
• Transmitting sensitivity: -89 dBm
• Material: black aluminum alloy
• Shockproof: 4G
• Power supply: DC 5-24V
• Working temperature: -4°F ~ 158°F
• Storage temperature: -22°F ~ 185°F
• Size: 2.9" x 1.8" x 2.2" (excluding bracket)

M Button
Flip Button
Parking Guideline Button
Press “ ”key on the front panel to open and close the parking guide
line. Just as shown in the image below.
Under single image display, press “ ”key on the front panel to turn
up/down/left/right the display image. Under multiple image display,
turn up/down/left/right the screen and menu (only for VTCRH2 and
VTCRH4).
43
2. Product Features
• Heavy Duty Wireless Waterproof Camera with IR night vision,
builtbattery and magnetic mounting.
• Camera with 3MP pixels image with 720P HD video streaming.
• 2.4G wireless transmission with no delay or deadlock.
• Transmission distance up to 700ft. in open area.
• A monitor with original IPS display with full viewing angle.
• 1024*800 resolution with 16:9 wide screen.
• Automatically shut off screen when there is no video signal and
starts up within a second when signal is detected.
• Camera operates for 18 hours with full charge.
3. Product Introduction
Monitor Introduction
3 4 5 6 7
2
1
1. 2.4G transmission antenna
2. LCD screen
3. “M”: enter/exit the menu
4. Flip: horizontally/vertically image flip
5. Power: turn on/off the monitor
6. Parking guide lines: on/off
7. Paring: long press to pair
VTCRH2 and VTCRH4 only:
- press shortly to switch display
Wireless Camera Introduction
5
6
1. 2.4G antenna
2. Night vision infrared light
3. Angle adjusting knob
4. Light sensor(night vision)
5. Power indicator
6. Power on/off
7. Built-in battery
8. Charging port
1
2
3
4
7
8
4. Menu Setup Introduction
Press the “M” key to open the option for contrast, saturation and
brightness, and then press “ ” or “ ” key on the front panel to set
the contrast, saturation and brightness. Just as shown in the images
below. And which will be saved and disappeared automatically after
5 seconds.

56
Image display mode switch
Press “ ”to switch image display mode.(only for VTCRH2 and VTCRH4)
Camera pairing
Under single image display mode, press and hold “ ”key on the front
panel to pair the cameras. Just as shown in the image below. Then
remove the power for the wireless camera and then powered it on
again. If pair successfully, it will show the camera image, if no, then
the screen will display “Pair fail), and you will need to repair it again.
The whole pair process will need about 10S. For multiple wireless
cameras, you will need to enter into the related channel display, and
then pair the cameras one by one(only for VTCRH2 and VTCRH4).
5. Connections
Wireless camera
Charged by cigarette car charger Powered by DC power cable
1. DC12-24V(By cigarette car charger or DC cable)
2. Brown line: trigger full screen to CAM 1
3. Green line: trigger full screen to CAM 2(to CAM 1 for VTCRH1)
4. Blue line: trigger full screen to CAM3
5. Grey line: trigger full screen to CAM4
DC1 2-2 4V input DC1 2-2 4V input
DC1 2-2 4V input
Wireless monitor