Breville 3X Bluicer Pro BJB815 User manual

Instruction Book - BJB815
the 3X Bluicer Pro™
BJB815_ANZ_IB_A19.indd 1 4/6/19 11:12 am

2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• Before using the first time
ensure your electricity supply
is the same as shown on the
label on the underside of the
appliance. This appliance is
equipped with a power cord
having a grounding wire with a
grounding plug. The appliance
must be grounded using a
properly grounded outlet.
In the event of an electrical
fault, grounding reduces the
risk of electrical shock.
• Do not, under any
circumstances, cut or
remove the third (ground)
prong from the power
cord or use an adapter.
• Consult a qualified electrician if
the grounding instructions are
not completely understood, or
if doubt exists as to whether the
appliance is properly grounded.
• The installation of a residual
current safety switch is
recommended to provide
additional safety when using
all electrical appliances.
Safety switches with a rated
2 Breville Recommends
Safety First
6 Components
7 Assembly
10 Functions
12 Care & Cleaning
14 Troubleshooting
Contents
BJB815_ANZ_IB_A19.indd 2 4/6/19 11:12 am

3
operating current not more
than 30mA are recommended.
Consult an electrician for
professional advice.
• Remove and discard
any packaging materials
safely, before first use.
• To eliminate a choking hazard
for young children, discard
the protective cover fitted
to the power plug safely.
• Always ensure the appliance
is properly assembled, as per
instructions, before use. Using
the appliance without being
properly assembled may cause
product malfunction, product
damage or pose safety risk
including personal injury.
• This appliance is for household
use only. Do not use the
appliance for anything other
than its intended purpose. Do
not use in moving vehicles or
boats. Do not use outdoors.
Misuse may cause injury.
• Position the appliance on a
stable, heat resistant, level, dry
surface away from the counter
edge, and do not operate on
or near a heat source such as
a hot plate, oven or gas hob.
• Fully unwind the power
cord before operating.
• Do not let the power cord
hang over the edge of a
counter or table. Do not let
the power cord touch hot
surfaces or become knotted.
• Do not leave the appliance
unattended when in use.
• If the appliance is to be left
unattended, cleaned, moved,
assembled or stored, always
switch off the appliance by
pressing the ON | OFF button
to OFF. Switch off and unplug
from the power outlet.
• Turn the appliance OFF, then
unplug from the outlet when
not in use, before assembling or
disassembling parts and before
cleaning. To unplug, grasp the
plug and pull from the outlet.
Never pull from the power cord.
• Regularly inspect the power
cord, plug and actual appliance
for any damage. If found
to be damaged in any way,
immediately cease use of
the appliance and return the
entire appliance to the nearest
authorised Breville Service
Centre for examination,
replacement or repair.
• Keep the appliance and
accessories clean. Follow
the cleaning instructions
provided in this book. Any
procedure not listed in this
BJB815_ANZ_IB_A19.indd 3 4/6/19 11:12 am

4
instruction booklet should be
performed at an authorised
Breville®Service Centre.
• This appliance is not intended
for use by children or by persons
with reduced physical, sensory,
or mental capabilities, or lack
of experience and knowledge.
Close supervision is necessary
when any appliance is used near
children. Children should be
supervised to ensure that they
do not play with the appliance.
• Children should not play
with the appliance.
• Cleaning of the appliance should
not be carried out by children.
• The appliance power cord, and
any components, attachments
or accessories should be
kept out of reach of children
aged 8 years and younger.
• Never use attachments or
accessories that are not supplied
with this product or authorised
by Breville to be used on this
product. Failing to follow this
instruction may cause product
malfunction, product damage
or even pose safety risk.
• Do not attempt to operate
the appliance by any
method other than those
described in this booklet.
• Do not move the appliance
while in operation.
• Do not operate the appliance
on an inclined surface.
• Do not push food into the
feed chute with your fingers
or other utensils. Always use
the food pusher provided.
Do not place hand or fingers
into the food chute when it is
attached to the appliance.
• Do not juice stone fruit
unless seeds and/or stones
have been removed.
• Make sure the product is
turned OFF and the
stainless-steel filter basket
has stopped rotating and the
motor has completely stopped
before releasing the safety
locking arm and/or attempting
to move the appliance,
when the unit is not in use,
and before disassembling,
cleaning and storing.
• Any significant spillage onto
the surface under or around
the appliance, or onto the
appliance itself, should be
cleaned and dried before
continuing to use the appliance.
• Be careful when handling the
stainless-steel filter basket as the
small cutting blades at the base
of the filter basket are very sharp.
Mishandling may cause injury.
• Blender blades are sharp,
take care when handling,
BJB815_ANZ_IB_A19.indd 4 4/6/19 11:12 am

5
emptying and cleaning the
blender jug.Remove rind from
all citrus fruit before juicing.
• Do not use the appliance
if the rotating sieve (filter
basket) or lid is damaged.
• Always make sure chute cover
is clamped securely in place
before motor is turned on.
• Do not operate without the
pulp container in place.
• Do not unfasten interlock arm
while unit is in operation.
• A representative example of the
heaviest loading anticipated for
use with this appliance is 450g
of frozen banana pieces and
1000g of milk blended on the
highest speed for 30 seconds.
• Do not juice more than 3kg
(approximately 6 pounds)
of carrot at a time.
• Avoid putting the blender
jug on the motor base while
the motor is still spinning.
• Do not operate without any
ingredients in the jug.
• Never attempt to operate
with damaged blades, or
with utensils, or any foreign
objects inside the jug.
• Do not put the jug in extremes
of heat or cold, for example
placing a cold jug into hot
water, or vice versa.
• Lid must be firmly secured
to the jug before operation to
ensure internal contents do
not escape, spray or overflow.
• Do not remove the jug
from the motor base while
blender is in use.
• Do not use blender while
OVERLOAD PROTECTION
is flashing on the LCD. If this
occurs, unplug the blender
and wait for 30 minutes until
the motor has cooled. Once
cooled, you will be able to use
the blender as usual again.
• Do not process hot or boiling
liquids. Allow to cool before
placing into the blender jug.
• To protect against electric
shock, do not immerse the
power plug, cord or appliance
in water or any liquid.
• Authorised Breville Service
Centres can be found on our
website www.Breville.com
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
BJB815_ANZ_IB_A19.indd 5 4/6/19 11:12 am

6
Components
A
I
H
J
K
L
M
B
C
D
E
F
G
A. Food pusher (not dishwasher safe)
B. Juicer cover (dishwasher safe)
C. Stainless steel filter basket (dishwasher safe)
D. Filter bowl surround (dishwasher safe)
E. Interlocking safety arm
Stops motor base operating without
cover locked into place.
F. Control panel
G. Stainless steel motor base
H. Inner measuring cup (dishwasher safe)
I. 1.5 litre blending jug & lid (dishwasher safe)
J. Juicing nozzle (dishwasher safe)
Can be placed over spout to juice
directly into a cup.
K. Drip stop plug
L. Pulp container (dishwasher safe)
M. Cleaning brush
For use on Stainless Steel Filter Basket.
BJB815_ANZ_IB_A19.indd 6 4/6/19 11:12 am

7
Assembly
BEFORE FIRST USE
Wash the lid, inner measuring cup, jug, the
filter bowl surround, filter basket, juicer
cover, food pusher and pulp container in
warm, soapy water with a soft cloth. Rinse
and dry thoroughly.
Place motor base on a flat, dry surface such
as a countertop. Ensure that the appliance is
switched to OFF at the motor base and the
power cord is unplugged.
JUICING
1. Place filter bowl surround on
top of the motor base.
2. Align the arrows at the base of the
stainless-steel filter basket with the arrows
on the motor drive coupling and push down
until it clicks into place to create a secure fit
with the motor base.
3. Place the juicer cover over the filter bowl
surround, positioning the lower part of the
feed chute over the stainless steel filter
basket.
4. Raise the safety locking arm up and locate
into the two grooves on either side of the
juicer cover.
BJB815_ANZ_IB_A19.indd 7 4/6/19 11:12 am

8
5. The safety locking arm should now be in a
vertical position and locked into place on
top of the juicer cover.
6. Slide the food pusher down the food chute
by aligning the groove in the food pusher,
with the small protrusion on the inside of
the top of the feed tube.
Food
pusher
groove
Small
protrusion
inside
feed tube
7. Place the pulp container into position by
tilting and lifting the motor base slightly.
Insert the pulp container under the juicer
cover on the back ensuring the front edge
is tucked under the back lip of the filter
bowl surround and the bottom edge is
clipped into the bottom of the motor base.
8. Drip stop plug can be fitted over juice
outlet nozzle. It then allows the outlet to
be plugged to prevent dripping
after juicing.
9. Fit the lid to the blender jug and position jug
under juice spout.
10.Optional: For juicing into a cup the
Juicing Nozzle can be fitted onto the juice
outlet nozzle.
BJB815_ANZ_IB_A19.indd 8 4/6/19 11:12 am

9
BLENDING
1. With the blender jug in the upright position
place it on the motor base. The handle
of the blender can be positioned to the
left or right-hand side of the appliance.
2. Raise the safety locking arm up
and locate into the two grooves
on either side of the blender.
3. Add food or liquid into the blender jug
ensuring not to exceed the ‘MAX’ mark.
Place the blender lid firmly into position on
the top of the blender jug. Insert the clear,
inner measuring lid into the blender lid and
turn clockwise to lock into position. The jug
features a Breville®Assist™ Lid. This allows
the lid to fit tightly onto the blender jug,
avoiding displacement during operation.
4. Ensure the spout cover of the blender lid
is clipped into place and closed. The ring
pull design allows the user to easily remove
the lid with a simple leverage action.
After appliance is assembled into blender or
juicer configuration, plug power cord into a
220–240V power outlet and turn on.
Press the ON / OFF button to turn the
appliance on. The ON / OFF button will
illuminate. The LCD timer screen will
illuminate with ‘0:00’ displayed.
BJB815_ANZ_IB_A19.indd 9 4/6/19 11:12 am

10
Functions
GETTING STARTED
The ON / OFF button powers the unit into
READY mode.
PRESET PROGRAMS
BLENDING
The appliance has 5 preset functions:
Smoothie, Green Smoothie, Pulse/Ice Crush,
Auto Clean and Frozen Cocktail. These
pre-programmed cycles automatically adjust
the blending time and speeds to optimise
blending results. These programs are only
activated when your appliance is in blender
set up. They can't be used when your
appliance is set up in juicing configuration.
Select the required function by pressing the
corresponding function button. The unit will
start to operate, and the selected function
button will illuminate. The timer will
start to count down and program will end
automatically when it reaches '0:00'.
The program and timer can be paused
by pressing the pause button. Resume by
pressing program button again, or cancel by
pressing pause again.
The program can also be canceled at any
time by pressing the ON|OFF button.
Turning the speed dial will interrupt the
program, placing the blender in manual
mode starting from Speed 1.
Smoothie
For dairy-based smoothies a combination of
speeds and pulses are designed to combine
and aerate ingredients into a smooth and
creamy texture.
Green Smoothie
For blending whole fruits/vegetables into
a smooth beverage. A combination of high-
speed profiles breaks down tough fibres into
very fine particles.
Frozen Cocktail
For creating ice-based cocktails and drinks
like Margaritas, Daiquiris and Slushies. An
ice crush program followed by a short blend.
Pulse / Ice Crush
A program of continuous pulsing designed
to chop food into an even consistency or
crush ice cubes. Use the PULSE button when
the food that is being processed is too thick
or coarse to circulate within the blender jug.
The pulse program can automatically detect
when ice has been fully crushed and ends
the program early, indicated by a series of
longer pulses.
BJB815_ANZ_IB_A19.indd 10 4/6/19 11:12 am

11
The maximum amount of ice cubes the
blender can blend without liquid in the jug
at any one time is 1 standard ice tray or
250g.
Auto Clean
Use to remove most of the ingredients off
the blender walls and blades. Add 2 cups
warm soapy water and press the clean
button. For harder to clean, sticky or thick
ingredients, add ½ teaspoon of dishwashing
detergent for extra cleaning power. For
best results, clean the blender jug this way
immediately after use. The Auto Clean
function only cleans the blender jug. It
doesn't clean the juicer.
MANUAL OPERATION
Speed Control Dial
Blending
Turn the Speed Control Dial clockwise to
select one of 10 speed settings from a slow
STIR through to a very fast PULVERIZE.
The timer will start to count up, and
blending will stop when it reaches '2:00'.
Blending can be paused by pressing pause
button. Press pause button again to cancel,
or turn dial to resume blending from
Speed 1.
To stop blending, turn the Speed Control
Dial anticlockwise back to READY or press
ON|OFF button.
JUICING
Wash your selection of fruit and vegetables
to be juiced. Most fruit and vegetables such
as apples, carrots and cucumbers will not
need to be cut or trimmed to size as these
will fit whole into the feed chute. Ensure
vegetables such as beets, carrots etc. have
all soil removed, are washed well and
trimmed of leaves before using.
1. Plug the power cord into your
220–240V power outlet.
IMPORTANT
Do not load feed chute with produce before
the Juicer has reached the selected speed.
Turning the Juicer On
Turn dial to desired speed setting. Use lower
numbers (1–5) for soft fruits and vegetables
and higher numbers (6–10) for hard fruits
and vegetables. See Speed Selector Guide
table on the next page to match speed and
produce type for maximum yield. "Low"
range, while it may not maximise yield
of some produce, allows you to extract
juice at a significantly lower noise level.
2. With the motor running, place food into
the feed chute and use the food pusher
to gently guide food down. To extract
the maximum amount of juice, always
push the food pusher down slowly.
3. Full Blender Jug
You can keep juicing until the jug is filled to
MAX. level.
WARNING
Never use fingers, hands or utensils to push
food down the feed chute or to clear the feed
chute. Always use the food pusher provided.
CAUTION:
sharp blades
The stainless steel filter basket contains
small sharp blades to cut and process fruit
and vegetables. Avoid touching the blades
when handling the filter basket.
BJB815_ANZ_IB_A19.indd 11 4/6/19 11:12 am

12
SPEED SELECTOR GUIDE
FOOD TYPE SPEED
APPLES 10
BABY SPINACH 9
BEETROOT 10
BLUEBERRIES 5
BROCCOLI 7
CABBAGE 9
CAPSICUM 9
CARROT 10
CELERY 4
CITRUS FRUITS (peeled) 1
CUCUMBER 4
GINGER 8
GRAPES (seedless) 2
HONEYDEW MELON (peeled) 3
KALE 9
KIWI (peeled) 5
MANGO (peeled, pit removed) 5
MINT 9
PEACH (pit removed) 5
PEARS 6
PINEAPPLE (peeled) 7
RHUBARB 8
SQUASH 9
STRAWBERRIES 4
TOMATOES 4
WATERMELON (peeled) 3
ZUCCHINI 6
Care & Cleaning
Ensure the motor base is turned off by by
pressing the ON / OFF button. Then unplug
the power cord.
CLEANING
1. Remove Blender Jug.
2. Disengage Locking Bar, pull up entire
Juice Collector Assembly and take to sink.
3. Remove Pulp Container.
Empty as much pulp as possible into bin/
compost. Rinse all parts after use (except the
motor base) under running water to clear
away the majority of juice and pulp. Wash in
warm soapy water with a soft cloth.
To avoid food drying on to the blades, mesh
or transparent parts, rinse and wash as soon
as possible after use.
PULP CONTAINER
To minimize cleaning, you can line the
pulp container with a biodegradable bag to
collect the pulp.
MOTOR BASE
Wipe down with a soft damp cloth. Do not
immerse the motor base in liquids.
CLEANING AGENTS
Do not use abrasive scouring pads or
cleaners on either the motor base or the jug,
as they may scratch the surface. Use only
warm soapy water with a soft cloth
BJB815_ANZ_IB_A19.indd 12 4/6/19 11:12 am

13
JUG AND LID
In order to keep your jug clean and avoid
food drying on the blades and jug, follow the
below steps as soon as possible after use.
Rinse most of the ingredients off the jug
and lid.
Fill the jug with 500ml of warm water, fit
the lid and press the AUTO CLEAN button.
If thick or sticky ingredients require extra
cleaning power add a few drops of dish
liquid detergent.
Rinse the jug and lid again and/or wash
separately in warm soapy water with a soft
cloth or bottle brush.
It is most effective to clean the jug
immediately after use.
FILTER BASKET
To ensure consistent juicing results,
always clean the filter basket thoroughly
immediately after use, using the included
brush.
If pulp is left to dry, it may clog the fine
pores of the filter mesh, which can affect
juicing performance. The filter basket can be
soaked in hot soapy water for 10 minutes,
if necessary.
DISHWASHER
All parts except for the motor base and food
pusher are dishwasher safe. The blender jug
can be placed on the bottom shelf of the
dishwasher. The lid and inner measuring
cap should be washed on the top shelf only.
However, washing parts on a regular basis
in the dishwasher can shorten the life of
them due to prolonged exposure to harsh
detergents, hot water and pressure.
Cleaning the parts in the dishwasher also
may cause parts to deteriorate so inspect the
parts regularly and stop using the product if
any signs of damage is noticed.
STUBBORN FOOD STAINS
Strong smelling foods such as garlic, fish
and some vegetables such as carrots may
leave an odour or stain on the blender jug
and lid. To remove, soak blender jug and lid
for 5 minutes in warm soapy water. Then
wash with a mild detergent and warm water,
rinse well and dry thoroughly. Store jug with
the lid off.
STORAGE
Store the appliance upright with the blender
jug assembled on the motor base, or beside
it. Do not place anything on top. To allow air
to circulate, keep the lid off.
WARNING
Oils in citrus rind can damage the material
of your blender jug if exposed to it for a
longer period. Always clean your blender jug
immediately after processing citrus rind.
BJB815_ANZ_IB_A19.indd 13 4/6/19 11:12 am

14
Troubleshooting
LCD screen turns on
but appliance doesn't
respond to controls.
• The safety locking arm may not be correctly engaged in the vertical operating
position. In this case, the LCD screen will show an animated prompt .
Check the top cover is properly aligned and the locking arm is located firmly
into the two grooves on either side of the juicer cover or blender jug.
Food is unevenly
chopped • This can happen when too much food is being added at one time.
Try a smaller amount, and work in batches if necessary.
Food is chopped too
fine or is watery • Try blending for shorter period of time. Use the PULSE function for
better control.
Excess pulp building
up in the stainless-
steel filter basket
• Turn the appliance off. Disassemble to scoop excess pulp off the juicer cover.
• Reassemble and continue juicing. Alternating soft and hard ingredients may
help avoid this.
Pulp too wet and
reduced extracted juice • The cleaner the filter, the better the juice yield, and dryer the pulp. Be sure to
thoroughly clean the juicer as soon as possible after each use. Remove the
stainless-steel filter basket and thoroughly clean mesh walls with a cleaning
brush. Rinse the filter basket under hot water. If the fine mesh holes are
blocked, soak the basket in a solution of hot water with 10% lemon juice to
unblock the holes or wash in the dishwasher (top shelf). This will remove
excess fiber build up which could be inhibiting the flow.
• Pusher force could reduce yield because it slows the motor down.
Avoid putting pressure on the food pusher when pushing ingredients down
the feed chute.
• If juicing large amounts of fibrous ingredients like rhubarb and pineapple,
cleaning the filter basket in between might be required.
Juice leaks between
the filter bowl surround
and the juicer cover
• Try a slower juicing speed and push the food pusher down the feed chute
more slowly.
• Ensure there is no build up in the filter basket.
Juice sprays out
from spout • The juice is being extracted too fast; try a slower juicing speed (if possible)
and push the food pusher down the feed chute more slowly.
Juice in filter bowl is
left after juicer stopped • Turn the speed dial up to highest speed setting and operate for 5 seconds.
That can help moving the remaining juice into the jug.
BJB815_ANZ_IB_A19.indd 14 4/6/19 11:12 am

15
Motor appears to
stall during juicing • Wet pulp can build up under the juicer cover and stall the appliance if the appliance is used excessively without cleaning. If this occurs, disassemble and
follow the cleaning instructions to clean the filter bowl surround, the stainless-
steel filter basket and the juicer cover. The appliance can also stall if excessive
force is used to push produce down the feed chute. If this occurs, ensure that a
gentler pressure is used to push produce down the chute.
• Turn on the appliance before putting ingredients in the chute. Pressing
ingredients down before the motor reaches full speed can cause it to stall
or overload. Use gentle to moderate pressure on the pusher. Lower pressure
produces a better juice yield.
• Hard fruit and vegetables will put excess strain onto the motor if a low speed
is selected. Refer to the reference guide to determine the correct speed for the
fruit and vegetables selected for juicing.
All control panel lights
flash and Overload
Protection displayed
on LCD screen
• This indicates motor overload protection is activated due to motor
overheating or stalling.
• To reset the protector, unplug from the power supply, then plug back in and
turn on.
• If overload protection is still displayed, unplug the appliance and leave to
cool for at least 30 minutes, then try again. The appliance must be unplugged
while cooling in order to reset properly.
• If the issue persists after allowing to cool, this indicates an internal problem.
Please call Breville Customer Service or your nearest Authorised Breville
Service Centre.
• Note that triggering the overload protection indicates abnormal use of
the appliance, such as too much load in the blender jug, excessive push
force when juicing or extended continuous use. Please take note of the
conditions and refer to all of the information in these instructions to avoid this
occurrence and extend the life of the appliance.
BJB815_ANZ_IB_A19.indd 15 4/6/19 11:12 am

Breville, the Breville logo and the Twin Turbo Pro are registered trademarks of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2019.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
BJB815 ANZ – A19
Web: www.breville.co.nzWeb: www.breville.com.au
Australian Customers
Phone: [phone]
New Zealand Customers
Phone: [phone]
Breville Customer Service Centre
BJB815_ANZ_IB_A19.indd 16 4/6/19 11:12 am