Brica baby in-sight 63013 User manual

User Manual
63013
Keep these instructions for
future reference as they
contain important information.
Adult installation required.
Accessories not included.
birth+
Magical Firefly Auto Mirror
baby in-sight®

Mirror Features
Front View
1
APower button
BPower indicator light
A
B
Important: For optimum performance, ensure the remote has an unobstructed
visual path to the mirror.
Remote Features
Top View Bottom View
2
CRemote Transmitter
DEntertaining Mode
ESoothing Mode
FVolume
GVisor Clip
HBattery Compartment
C
D
E
F
G
H

3
Operating Mirror
Remove Demo Tab
The mirror is equipped with a “demo mode” feature. Before using the mirror,
pull out the plastic demo tab located on the back of the battery box and
discard it for normal operation.
Important: The mirror includes 3 “AA” batteries for in-store demonstration
only. Battery life may be impaired. Replace mirror batteries with 3 new “AA”
alkaline batteries (not included ) for normal use. Remote requires 1 “CR2032”
coin cell battery (not included).
1. Press button on front of mirror. Power indicator light will appear. The
button on the front of the mirror must be pressed in order to operate
remote control and mirror features.
2. Press desired mode on remote control:
Soothing Mode
a. Press button on remote once to activate soothing mode. Press again
to stop.
NOTE: Soothing mode stops automatically after approximately 12 minutes.
Press button again to restart.
Entertainment Mode
b. Press button on remote once to activate entertainment mode. Press
again to stop.
NOTE: Entertainment mode stops automatically after approximately 12
minutes. Press button again to restart.
Important: For optimum performance, ensure the remote has an unobstructed
visual path to the mirror.
4
Operating Mirror, continued
Auto Shut-Off Battery Conservation
To help conserve battery life, the mirror automatically shuts off after 1 hour of
inactivity. The power indicator light will turn off and mirror cannot be activated
by the remote during this time. To reactivate, press button on mirror. Power
indicator light will appear.
Manual Shut-Off
Press and hold button for 3 seconds. Power indicator light will turn off.

5
Battery Installation
Remote
Battery
Door
Important:If the mirror does not respond to the remote, it does not necessarily
mean that the battery power in the remote is low. Check the orientation of the
batteries in the battery compartments to make sure they are properly installed.
Remote:
• Loosen the screw in the battery compartment
door with a Phillips head screwdriver. Remove
the battery compartment door.
•Correctly insert 1 “CR2032”coin cell battery with
the polarity shown in battery compartment.
• Replace the battery compartment door and
tighten the screw with a Phillips head
screwdriver. Do not overtighten.
Battery Installation, continued
6
Mirror:
Remove Demo Tab: The mirror is equipped with
a “demo mode” feature. Before using the mirror,
pull out the plastic demo tab and discard it for
normal operation.
Important: The mirror includes 3 “AA” alkaline
batteries for in-store demonstration only. Battery
life may be impaired. Replace mirror batteries
with 3 new “AA” alkaline batteries (not included)
for normal use.
Hint: Remove the mirror from the seat back prior to replacing the batteries.
• Loosen the screw in the battery compartment door with a Phillips head
screwdriver. Remove the battery compartment door.
• Correctly insert 3 “AA” batteries with polarity shown in battery compartment.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw with a Phillips
head screwdriver. Do not overtighten.
Important: Under normal use conditions, the batteries in the mirror will
require replacement more often than the battery in the remote. When the
mirror’s music becomes faint, it’s time to replace the batteries in the mirror.
PULL
Mirror
Battery
Door

7
In exceptional circumstances, batteries may leak fluids that can cause a chemical
burn injury or ruin the remote or the mirror. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated in battery compartments.
• Remove batteries during long periods of non-use. Always remove exhausted
batteries from the remote and mirror. Dispose of batteries safely. Do not
dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the remote and mirror before charging.
• If rechargeable batteries are used, they are only to be charged under
adult supervision.
Battery Safety Information
Shown Actual Size
CR2032
Lithium Battery
3V
1.5V x 3
AA (LR06)
Shown Actual Size
8
Important Safety Precautions:
Keep mirror out of baby’s reach and direct sunlight. Always carefully follow
car seat manufacturer’s directions for correct installation and position of a
child safety seat.
To Clean:
Wipe the mirror with a soft, damp cloth. Fabric is surface washable with a
damp cloth and mild soapy water. Do not submerse mirror in water.
CAUTION
Always verify that the mirror is properly secured on the seat
back, head restraint or tether anchor. Check frequently.
!
Prevent strangulation or entanglement. Never place or
attach to a crib. Never add strings or ties to the product.
Never leave child unattended.
WARNING
!

9
Mirror Features
Rear View
3
KBattery Compartment
ID-Ring
JAdjustable Stand
J
LFastener
MClamp
NStrap
OClip
I
K
L
N
O
M
10
Attaching Mirror
Back Seat Head Restraint
• Raise head restraint.
• Insert clamp underneath head restraint.
• Wrap adjustable stand over top of head restraint.
• Bend clamp upward to conform to head restraint.
• Attach strap’s clip to D-Ring.
• Lower head restraint down to secure in place.
• Tighten strap and rotate mirror to desired angle so your child is visible to driver
in vehicle’s rear-view mirror.
Strap
Clamp
Clip
D-Ring
Adjustable
Stand

11
Attaching Mirror
Tether Anchor
IMPORTANT: DO NOT ATTACH THIS PRODUCT TO YOUR VEHICLE’S TETHER ANCHOR
IF YOUR CHILD SAFETY SEAT IS INSTALLED IN YOUR VEHICLE USING THIS ANCHOR.
• Position mirror on seat back in front of tether anchor.
• Insert clamp between seat back and rear deck of your vehicle.
• Bend clamp to conform to seat back shape.
• Attach clip to tether anchor and tighten strap.
• Unfasten adjustable stand’s fastener and tilt mirror to desired angle so your
child is visible to driver in vehicle’s rear-view mirror.
NOTE: The tether anchor attachment method is designed for sedan vehicles. If you own a
minivan, station wagon or sport utility vehicle (SUV) and would like to use the tether anchor
attachment method, you may need a tether extender. Please visit BRICA
®at brica.com or
call 1.866.869.8257
Adjustable Stand
Fastener
Clip
Tether
Anchor
Clamp
12
Attaching Mirror
Center Back Seat on Bench Seat
• Position mirror on center of back seat.
• Bend clamp to conform to top of seat back.
• Squeeze clamp firmly to secure mirror in place.
• Unfasten adjustable stand’s fastener, and tilt mirror to desired angle so your child is
visible to driver in vehicle’s rear-view mirror.
Adjustable
Stand
Clamp
Fastener
NOTE: If a tether anchor is accessible and not in use by your child safety seat, attach clip
to tether anchor and tighten strap. This will help increase the stability of mirror. If you own
a minivan, station wagon or sport utility vehicle (SUV), you may need a tether extender.
Please visit BRICA®at brica.com or call 1.866.869.8257

13
Attaching Mirror
Front Head Restraint (for forward-facing children)
• Raise head restraint up.
• Insert clamp underneath head restraint.
• Wrap adjustable stand over top of head restraint.
• Bend clamp upward to conform to the head restraint.
• Attach strap’s clip to D-Ring.
• Lower head restraint down to secure in place.
• Tighten strap and adjust the mirror so child can see themselves.
NOTE: This method is used for mounting mirror to back side of driver or front passenger
seat for entertaining forward-facing children.
Clamp
Adjustable
Stand
Strap
Clip D-Ring
14
FCC Note (United States Only)
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the legal limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio /TV technician for help.
NOTE: Changes or modifications not expressively approved by the manufacturer
responsible for compliance could void the user’s authority to operate the equipment.

making together better™
Questions?
Retain this address for future reference.
USA
©2013 BRICA, Inc., 500 West 5th Street,
Suite 220, Charlotte, NC 28202
1.866.869.8257 • brica.com
Australia
CNP Brands, PO Box 8 Deer Park VIC 3023
1 300 667 137 • cnpbrands.com.au
Printed in China