Brickcom FB-H200Np-S-WDRPro Datasheet

Easy Installation Guide
Megapixel Network Camera
FB-H200Np-S-WDRPro

1
Please install an easy-to-use breaker during installation and wiring in case it is necessary to make an
emergency break.
Please prevent the power cord from being trampled or pressed especially the plug, socket and the connecting
part led out from the device.
Please use power supply in the safe voltage range of our product. Make sure if the power supply is correct
before running the device.
During installing and using the device, please follow local electrical safety regulations strictly.
Please connect cables of power, alarm, audio and RS-485 with the power off. Hot-line wiring is not allowed.
When shipping, storing and installing the device, try to prevent it from damages caused by pressure, violent
While shipping the camera, pack it in the factory packing or use materials with equivalent quality.
This product is not water-proof and cannot be used outdoor alone.
vibration and soaking.
Please transport, use and store the device within defined humidity and temperature ranges.
Do not focus the camera lens on strong light such as the sun or incandescent lamp; otherwise the strong light
will cause overexposure or light leak (not camera malfunction), which may shorten camera lifetime.
Do not expose it in damp, dusty, extremely hot or cold places or places with intense electromagnetic radiation
or with unstable lighting.
Keep the camera away from water or any liquid to avoid damage to internal components.
To avoid heat accumulation, please do not block the ventilation around the device.
1. Power Supply
2.Working Environment
I. Preface
II. Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger or
property loss. Please read this Guide carefully before using the product, and keep it properly for future
reference. If the product cannot work normally or is damaged because the user does not follow the safety
instructions, we shall not assume any responsibility. Thanks for your cooperation.
Thank you for purchasing our product. If there is any question, please do not hesitate to contact us.
Working Environment
DC1 2V/AC24V/POE
10%~95% (non-condensing)
Voltage
Temp.
Humidity
Altitude
Pressure
-60m~3000m
86kPa~106kPa
-40℃ ~ +70℃
Other: -20℃ ~ +60℃
Power 6W

2
3. Daily Maintenance
4. Special Statement
Do not disassemble or repair the device in any way by yourself. We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.
If the product does not work properly, please contact your dealer or the nearest service center.
When the lens is contaminated by dust or grease, use cotton cloth or lens clean cloth to wipe it off. When it is
hard to clean, dip some lens cleanser and wipe gently and rotate outward from the middle until it is clean.
Never apply any organic solvent with ethanol or benzene to clean the lens and housing.
Do not touch the heat component of the device directly to avoid empyrosis.
Accessing this device to the internet is at user's own risk, including but not limited to the possible network
attack, hacker attack, virus infection and etc. This company will not assume any responsibility for problems of
product abnormality and information disclosure caused thereof. We shall provide technical support relating to
the products in time.
Every effort has been made to ensure the accuracy and validity of this Guide. Any update of this Guide caused
by version upgrade is subject to change without notice.
To ensure the safety of device on internet, it is strongly recommended that you set a strong password which is
composed of at least 2 kinds of the following, digits, case-sensitive letters or specific symbols, and whose
length ranges from 8 to 16 bits. Please modify the password periodically and once every 3 months is
recommended. If the device is used in highly risky environment, suggest modifying the password monthly or
weekly. Please keep your user name and password safe.
This device can be used after being activated through IPCSearch. During activation please fill a valid email
address for finding back the password.
This Guide is made for multiple models but it will not illustrate one by one. Please refer to it according to the
actual products you are using.
The product appearance is subject to the actual device and picture in this Guide is for reference only..

3
III.Installation Steps
1. Remove the dust cover and mount the lens. CS type lens can be mounted directly, while an adapter ring is
needed before mounting C type lens, as the picture shows.
[Note]: Back focus adjustment is unavailable for this series.
DC IRIS, for Auto IRIS lens
Mount an adapter
ring for C type lens
If the lens does not focus well after
adjustment, try to mount a spacer.
If the lens does not focus well after
adjustment, try to mount a spacer. DC IRIS, for Auto IRIS lens
The connector interface of different models may differ. Please refer to the pictures below according to the
actual cameras.
2. Connect the cable and power on.

4
OUT
GIN
GO1 O2 I 1 I 2B
RS4 85
LAN
Mic ro SD
DC 12 V
VID EO OU T
RUN
LIN K
ALA RM AU DIO
A
Audio In/Out
RS485 Port
RS485 Port
RS485 Port
TF Card Slot
Max Memory 256G
TF Card Slot
Max Memory 256G TF Card Slot
Max Memory 256G
TF Card Slot
Max Memory 256G
Video Out:
-Some models
support HD-SDI
-Other models
support CVBS
Video Out:
-Some models
support HD-SDI
-Other models
support CVBS
Video Out:
-Some models
support HD-SDI
-Other models
support CVBS
Video Out:
-Some models
support HD-SDI
-Other models
support CVBS
Power Port,
DC12V/AC24V
Power Port,
DC12V
Power Port,
DC12V/AC24V
Power Port,
DC12V/AC24V
Audio In/Out
Alarm In/Out
Indicator
Network Port
some models
support PoE
Indicator
Indicator Indicator
Network Port
some models
support PoE
Network Port
some models
support PoE
Network Port
some models
support PoE
Alarm In/Out Alarm In/Out
Alarm In/Out
Audio In/Out
Audio In/Out
RS485 Port

LINK Lamp: network status indicator, green, flashes (1s on, 1s off) after power on and network connected, and
goes off after power off or network disconnected.
[Note]:
RUN Lamp: operation indicator, green, flashes (1s on, 1s off) after power on, and goes off after power off.
The default packing does not include a power adaptor. Please buy separately from us or otherwise.
5
IV.Login to Client
1. Minimum environment requirements:
ŸProcessor: 3.3 GHz CORE®i3 series or other equivalent processors
ŸRAM Memory: 4GB or above
ŸOperating System: Windows XP or newer version
ŸBrowser: suggest using IE Kernal browser, other Kernal browsers may affect some functions of the client
ŸDirectX：9.0c
LAN
RS485 Port
Alarm In/Out
Audio In/Out
Video Out
-Some models
support HD-SDI
-Other models
support CVBS
TF Card Slot
Max Memory 256G
Network Port
some models
support PoE
Indicator
Power Port,
DC12V/AC24V
2. Device Activation
When using the device for the first time, run IPCSearch: it will search devices in LAN automatically and display
the list of device IP address, gateway and etc. If the network provides DHCP service, DHCP server will assign
IP for the camera automatically.

6
Individual: Select the device from IPCSearch and right click to select “Activate”. Fill admin user name and
password and the e-mail address to find back the password. Click “Activate” and it will reboot automatically.
Batch: Select the device and click “Batch processing”. In the popup interface, set admin user's password and
the email address to find back the password. Click “Activate” and it will reboot automatically.
Web client: The device can also be activated through the web client. Set PC and the device in the same
network segment and login to the web. User can set admin password and password reset email on the
interface and click "Activate".

7
3. Modify device IP address
4. Login to the device
1“ ”) Double click the device in IPCSearch or click Login . Enter username and password to login the web client.
Click “Modify Params” and set the network parameters. When configuring a static IP for the camera, please
check “Custom device address (Close DHCP)” and fill the Ethernet parameters. During modification, the
username (admin) and the password set during activation should be entered. After configuration, the camera
will reboot automatically.
Adjust lens direction and edit parameters on the web client until the image reaches requirements.
3) Re-login to the web client and view live video directly.
2 successfully video (IE Kernal browser)) After login , download and install the plug-in .
[Note]: Interfaces of different models may differ. Please subject it to the actual products. Please refer to the
Help file for detailed explanation.

V. Bracket Installation
When mount the camera on a ceiling mount bracket, the bracket adapter can be taken apart from the bottom
and be mounted on the top of the camera, as the picture shows.
Screw Hole
Bracket Adapter Camera Top View
VI. Housing Installation
When the camera works outdoor, it should be installed in a water-proof housing, explanation as follows:
1. Unscrew the snap-fit and open the cover of the housing.
2. Use a screwdriver to loosen the screws on the holder, pull the holder backward and take it from the holes.
[Note]: You only have to unscrew the screws on the holder, no need to screw them off.
3. Route the cable and screw up the PG joint. Suggest making the PG joint water-proof and dust-proof.
4. Place the holder at the bottom of the camera.
5. Install the camera and the holder in the housing.
[Attention]: Before fixing, put the camera lens close to the window of the housing without any obvious gap (gap
only enough for focus), to avoid light leak or halo.
6. Wire camera connectors to the connector board of the housing, cover the housing and lock it up.
8
Size of bracket adapter
PG Joint
5
Open the snap-fit
1
Pull the holder backward
Align to the hole,
take off the fixing board
3
4
2Loosen screws
Screw Hole
Holder
Camera
6Assemble fixing board
Route cables and tighten PG joint

V3 20 190716