Brighter Eye 900 Pro User manual

1
Eye 900 Pro
LED Wash
This product manual contains important information about the
safe installation and use of this projector. Please read and follow
these instructions carefully and keep this manual in a safe place
User manual
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions..........................................................................................................................................3
2. Unpacking.......................................................................................................................................................4
3. Features & Specifications ...............................................................................................................................5
5. Menu Operations ...........................................................................................................................................5
6. Installation......................................................................................................................................................6
7. DMX-512 Control Connections.......................................................................................................................6
8. DMX Channels ................................................................................................................................................7
10. Maintenance and Cleaning.........................................................................................................................14
STATEMENT
The product has full capability and intact packing when leaves factory. All the users should
comply with provided warnings and manual. Any damages caused by misuse are not
included in our guarantee. We cannot be responsible for any malfunctions & problems
owing to ignoring the manual.

3
1. Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as it is fire
hazard.
Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but
always by taking its base.
Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is
higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hands during its operation. Turn off the power and allow
about 15 minutes for the unit to cool down before replacing or serving.
In case of serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance centre. Always use
the same type spare parts.
DO NOT touch any wire during operation as high voltage might be causing electric shock.
This unit belongs to class 1 protective lights, so the lights must be grounded
well. Should be grounded by the professional.
Please confirm the voltage is among the range mentioned in this user manual.
Please confirm the power cord is undamaged.
Please cut off the power before cleaning the lights.
Don't use knife to drag the power cord when unplugging.
Be careful when installing the light. Don’t touch the bare wire, to avoid the electric shock.
Don't look straight at the light source when the light is on, otherwise your eyes can be hurt.
When choosing the installing position, please confirm the light is not exposed to the high
temperature, moist or dusty place. Minimum distance between units is 0.5 m.
Please use proper, applicable and safe wires to connect the light.
Installation or dismantling should be operated by professional engineer.
Please don't modify the light on your own, which can cause short circuit, burn, electric
shock, etc. Otherwise the manufacturer won't consider warranty.
Warning:
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.

4
DO NOT open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs by yourself. If your unit requires service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always
use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at the safe place where it is not
available for other people.
AC Power Supply
The equipment power supply is able to adapt to the wide input voltage range. Please confirm if the
input voltage is in the scale of rated voltage. The equipment can adapt to100V-240V AC voltage,
Frequency 50-60HZ. It cannot be used with rheostat (variable resistor) or in dimmer circuits.
2. Unpacking
Please carefully unpack it when you receive the fixture and check whether it is damaged during the
transportation. And please check whether the following items are included inside the box:
Equipment x 1
Power cable with Plug x 1
User manual x 1
Iron holder x 2

5
3. Features & Specifications
Rated Voltage: AC100V～240V 50-60HZ
Rated Power: 450W
LED Qty: 19x15W high power 4in1 LEDs
LED Drive Current: 1000mA
Beam Angle: 4-60°Zoom
IP: IP20
DMX Mode: 21CH（Standard/35CH(Shapes)/78CH(Extend)/97CH(Extend RGBW))/92CH(Full)
Net weight: 15 Kg
Gross weight: 18.2Kg
XLR sockets input/output 3Pin
Power input/output
3 kinds of control model: DMX512, Sound active, Master/slave
LCD display screen
Display screen can be turned upside down with 180°to fit the installation in different place
Indoor operation temperature: -20°C～+40°C
5 DMX modes: 21/35 /78/97/92CH
dimmer:0-100% linear dimmer
Pan/tilt:
o16bit fine pan/tilt control
oSmooth and accurate locating
oPan: 540° Tilt:210°
oMotor rotation in forward and reverse can be set up
Each LED can be controlled individually
0-20HZ Strobe, pulse strobe, Asynchronous stroboscopic effect.
Super mixed color and rainbow effect
All the color can be for the total dimmer.
7 programmable program is invoked by controller.
Fan cooling(fan will be change the speed with the temperature variation.
Temperature detecting system (If the temperature detection error, the light doesn’t work).
5. Menu Operations
Control board function
Button
Function
MENU
Choose Menu or function exit
ENTER
Current show menu or enter into the current selected function
UP
Increase the value
DOWN
Decrease the value

6
6. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always
use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at the safe place where it is not
available for other people.
7. DMX-512 Control Connections
This product accepts the international standard DM 512 ( 1990) of the digital control signal.
Please use the 3 pin or 5pin XLR plugs&socket offed by factory to connect the first projector’s input to
the second projector output, and connect the second projectors output to the third projectors input
and so on. Eventually connect the last projectors output.
The projectors control signal output or input by using the 3 or 5 pin XLR pug and socket. If need to
lengthen the communication cable(standard meter is 2 meters),please make sure the both side of 3 or 5
pin plug is one to one.(one to one, two to two, three to three ).Otherwise ,the communication cable will
be interrupted. The communicate cable is 2-cord screened cable 75Ω resistance with each core having
at least a 0.5mm diameter.
It is highly recommend to use the DMX signal terminator for the installation to avoid the electronic noise
damage the digital control signal. Simply speaking, DMX terminator is an XLR CINNEXTOR WITH A 120Ω
1/2 W resistor connected across pin 2 and 3. Which is plugged into the output socket on the last projector
in the chain. See illustrations below:

7
8. DMX Channels

8

9

10