Brighter X-Dot User manual

1
Powerful Moving Head with Dot Glow System, Art-Net and Extraordinary RGBL colour mixing
User manual
Please read the instructions carefully before use
This
product
manual
contains
important
information
about
the
safe
installation
and
use
of
this
projector.
Please
read
and
follow
these
instructio
ns
carefully
and
keep
this
manual
in
a
safe
place
for
future
reference.
X-Dot
–7x60W Advanced Outdoor Wash Light

2
SAFETY PRECAUTIONS
This fixture is a sophisticated piece of electronic equipment.To guarantee a smooth
operation,it is important to follow all instructions and guidelines in this manual.
Professional is not responsible for injuries and/or damages resulting from the misuse
of this fixture due to the disregard of the information printed in this manual.Only
qualified and/or certified personnel should perform installation of this fixture and only
the original rigging parts included with this fixture should be used for installation.Any
modifications to the fixture and/ or the included mounting hardware will void the
original manufacturer’s warranty and increase the risk of damage and/or personal
injury.
PROTECTION CLASS 1-FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.DO NOT
ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR
MANUFACTURER’SWARRANTY. DAMAGES RESULTING FROM MODIFICATIONS
TO THIS FIXTURE AND/ OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’SWARRANTY AND
ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/ OR REPAIRS.
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION,AS IT MAY BE HOT! KEEP
FLAMMABLE MATERIALS AWAY FROM FIXTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK -MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A
DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS)TO
PREVENT WATER CORROSION AND/ OR ELECTRICAL SHORT CIRCUIT.
MINIMUM DISTANCE TO OBJECTS/SURFACES
MUST BE 3.3FEET (1METER)
MAXIMUM TEMP OF EXTERNAL SURFACE 185° F(85°C)
MINIMUM DISTANCE OF FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6
FEET (0 .5 METER)

- 3 -
SAFETY PRECAUTIONS
• DO NOT TOUCH the fixture housing during operation. Turn OFF the power and
allow approximately 15 minutes for the fixture to cool down before servicing.
• DO NOT shake fixture, and avoid brute force when installing and/or operating
fixture.
• DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if
any of the power cord connectors are damaged and do not insert into the fixture
securely with ease.
• NEVER force a power cord connector into the fixture. If the power cord or any of
its connectors are damaged, replace it immediately with a new one of the same power
rating.
• DO NOT block any air ventilation slots.
• All fan and air inlets must remain clean and never blocked.
• Allow approx.6” (15cm) between fixture and other devices or a wall for proper
cooling.
• Always disconnect fixture from main power source before performing any type of
service and/or cleaning procedure.
• Only handle the power cord by the plug end. Never pull out the plug by tugging the
wire portion of the cord.
• During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
• Consistent operational breaks will ensure fixture will function properly for many
years .
• ONLY use the original packaging and materials to transport the fixture in for
service.

- 4 -
MAINTENANCE GUIDELINES
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
CLEANING
Frequent cleaning is recommended to ensure proper function,optimized light output,
and an extended life.The frequency of cleaning depends on the environment in which
the fixture operates: damp,smoky or particularly dirty environments can cause greater
accumulation of dirt on the fixture’s optics.Periodically clean the external lens surface
with a soft cloth to avoid dirt/debris accumulation.NEVER use alcohol, solvents, or
ammonia-based cleaners .
MAINTENANCE
Regular inspections are recommended to ensure proper function and extended life.
There are no user serviceable parts inside this fixture.Please refer all other service
issues to an authorized our service technician.Should you need any spare parts,
please order genuine parts from your local dealer.
Please refer to the following points during routine inspections:
• A detailed electric check by an approved electrical engineer every three
months, to make sure the circuit contacts are in good condition and prevent
overheating.
• Be sure all screws and fasteners are securely tightened at all times. Loose
screws may fall out during normal operation, resulting in damage or injury as larger
parts could fall.
• Check for any deformations on the housing, color lenses, rigging hardware, and
rigging points (ceiling, suspension, trussing).Deformations in the housing could allow
for dust to enter into the fixture. Damaged rigging points or unsecured rigging could
cause the fixture to fall and seriously injure a person(s).
• Electric power supply cables must not show any damage, material fatigue or
sediments. NEVER remove the ground prong from the power cable.

- 5 -
OVERVIEW