BRIO Moderna CLPOU730UVRO4CF User manual

Point-of-Use Water Dispenser
& Coee Maker
User’s Manual
Model: CLPOU730UVRO4CF
+CAFÉ

2
Table of Contents
Safety Information ................................................................3
Intended Use .....................................................................4
Product Features .................................................................4
Touch Panel Description............................................................5
Operational Specifications ..........................................................5
Technical Specifications ............................................................5
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Materials Needed .................................................................6
Installation .......................................................................6
Determine Installation Location......................................................6
Connect to the Cold Water Supply ...................................................7
Make the Reverse Osmosis Waste Connections .......................................8
Flush the Filters ...................................................................9
Install the Filters and Complete the Installation ....................................... 10
Operation....................................................................... 11
Turn the Dispenser On/O ..........................................................11
Set the Time ......................................................................11
Set the Cold Water Temperature Level ...............................................11
Dispense Cold Water ............................................................. 12
Disable Child Safety Lock and Dispense Hot Water ................................... 12
View Before and After Concentrations of TDS in Water ................................ 12
TDS Reduction Rates ............................................................. 12
Prepare Beverages ............................................................... 13
Troubleshooting .................................................................14
Cleaning and Maintenance ........................................................14
Care and Maintenance ............................................................ 14
Filter Replacement Schedule....................................................... 15
Replace the Filters................................................................ 15
Filter Specifications ............................................................... 15
Warranty........................................................................16

3
Safety Information
WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling,
installing and operating the dispenser.
WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause
personal injury. When operating this dispenser, always exercise basic safety precautions, including
the following:
•Prior to use, this dispenser must be properly assembled and installed in accordance with this
manual.
•For indoor use only. Keep the water dispenser in a dry place away from direct sunlight. Do
NOT use outdoors.
•Install and use only on a hard, flat and level surface.
•Do NOT place the water dispenser in an enclosed space or cabinet.
•Do NOT operate the dispenser in the presence of explosive fumes.
•Use only properly grounded outlets.
•Do not use an extension cord.
•Always grasp the plug and pull straight out from the outlet. Never unplug by pulling on the
power cord.
•Do NOT use the dispenser if the cord becomes frayed or otherwise damaged. If the supply
cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
•To protect against electric shock, do NOT immerse cord, plug, or any other part of the
dispenser in water or other liquids.
•Ensure the water dispenser is unplugged prior to cleaning.
•Never allow children to dispense hot water without proper and direct supervision. Unplug the
unit to prevent unsupervised use by children.
•Service should be performed only by a certified technician.
•The appliance must not be cleaned by a water jet and is not suitable for installation in an area
where a water jet could be used.
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than
those recommended by the manufacturer.
•This appliance should work under environment of temperatures from 39–100 °F (4–38 °C)
and humidity ≤90%.
•Never turn the machine upside down or lean it more than 45°.
•After turning the dispenser o, allow the dispenser to sit idle for 3 minutes before turning on
again.
WARNING: UV light source. Disconnect the electrical supply to the UV radiation BEFORE opening cover.
•UV-LED lamp must be repaired by manufacturer only.
•UV-LED lamp model no. YB09-950-022, rated DC 24V, 0.17W±20%.
•Disposal of the UV-LED lamp must be done in accordance with local laws and regulations.

4
Intended Use
This appliance is intended to be used in household and similar applications such as:
•Sta kitchen areas in shops, oces and other working environments
•Farm houses
•Hotels, motels and other residential-type environments
•Bed-and-breakfast environments
•Catering and similar non-retail applications
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Product Features
Part Description Part Description
1 Touch panel display 10 RO pump
2 Water tap 11 Filter cabinet
3 Brewer cup drawer 12 Night light switch
4 Coee drip tray 13 Cooling switch
5 Water drip tray 14 Condenser
6 Sediment filter 15 Heating switch
7 Pre carbon filter 16 Drain outlet
8 Reverse osmosis (RO) filter 17 Water inlet
9 Post carbon filter 18 Water outlet

5
Touch Panel Description
No. Description
1 Up arrow button
2 Change PCB filter icon
3 Change RO filter icon
4 LED display
5 Self-cleaning UV icon
6 Water production icon
7 Down arrow button
8 Lock button
9 Hot water button
10 Brew button
11 Cold water button
Operational Specifications
Model No. CLPOU730UVRO4CF
Rated Voltage / Frequency 115 V / 60 Hz
Heating Power 700 W
Cooling Power 100 W
Operating Ambient Temperature 39100 °F  438 °C
Operating Humidity ≤90%
Operating source water TDS* ≤250 PPM
*Please note, hardness levels in source water greater than 250 ppm can cause scale buildup,
resulting in permanent damage to the hot water tank.
Technical Specifications
CAUTION: This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact
with hot water. Keep children and pets away from unit while dispensing. Never allow children to
dispense hot water without proper and direct supervision. Unplug unit to prevent unsupervised
use by children.
Model No. CLPOU730UVRO4CF
Hot Water Tank Volume 1 L
Cold Water Tank Volume 3.6 L
Hot Water Capacity (Measured at Ambient Temperature of 77 °F / 25 °C) 6 L/h (≥185 °F / 85 °C)
Cold Water Capacity (Measured at Ambient Temperature of 77 °F / 25 °C) 2 L/h (≤50 °F / 10 °C)
Hot Water Flow Rate ≥1.5 L/min
Cold Water Flow Rate ≥2.7 L/min
Net Weight 45.67 lb (20.72 kg)
Product Dimensions (WxHxD) 12.2 x 40.94 x 13.39 in. (31 x 104 x 34 cm)
Water Dispense Point to Water Drip Tray 11.5 in. (29.21 cm)
Coee Dispense Point to Coee Drip Tray (H) 6.22 in. (15.8 cm)
Coee Dispense Point to Water Drip Tray (H) 8.26 in. (20.98 cm)
Water Drip Tray Dimensions (WxD) 11.5 x 4 in. (29.21 x 10.16 cm)
Noise (dBA) ≤60 dB
8 9 10 11
1 75432 6

6
Package Contents
A
B
G
C
D
E
F
H
I
Part Description Quantity
A Filter flushing tube 1
BShut-o valve tube
(7 ft.) 1
CFilter housing (for
filter flushing) 1
D Filters 4
Part Description Quantity
EFeedwater adapter
(with extra nut) 1
F Plumber’s tape 1
GDrain saddle with
foam gasket 1
H RO water outlet tube 1
I Tube cutter 1
Materials Needed
Wrench Electric drill with 1/4 in. drill bit
Installation
1. Determine Installation Location
A. Place the dispenser upright.
B. Locate the dispenser on a hard and level surface in a cool shaded
location near a grounded wall outlet.
NOTICE: Do NOT plug in the power cord until the entire installation
section is completed.
C. Position the back of the dispenser no closer than 8 in. (20 cm) from a
wall and permit free airflow between the wall and water dispenser.
2. Install the Brewer Drawer and Drip Trays
A. Unwrap brewer cup drawer (3) and drip trays (4 and 5) from the
packaging material and slide them onto the dispenser as shown in
the illustration, until securely in place.
3
4
5

7
3. Connect to the Cold Water Supply
CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the
unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your filters.

8
A. Turn o the cold water supply, then
disconnect the cold water pipe from the
cold water supply line.
B. Connect the feedwater adapter (E) to
the cold water supply line.
C. Connect the cold water pipe to the top
of the feedwater adapter (E).
NOTE: An extra adapter nut is included
on top of the feedwater adapter
(E) to attach to a 3/8 in. or 1/2 in.
feed plumbing line.
E
D. Insert the shut-o valve with tube (B)
straight into the quick connector piece
of the feedwater adapter (E).
E
B
E. Gently tug on the tube (B) to ensure a
secure connection with the feedwater
adapter (E). E
B
4. Make the Reverse Osmosis Waste Connections
The “RO” filter assembly requires a drain line connection to be
installed, which removes rejected water to the sewer. The drain
saddle connects the drain line from the dispenser to your drain
pipe. The drain saddle is designed to fit around a standard 1.5 in.





9
OD (outer diameter) drain pipe.
Always install the drain saddle before the P-trap and on a straight vertical or horizontal section of the
pipe.
To avoid clogging the drain line with debris, do not install the drain saddle after the drain pipe meets a
garbage disposal or dishwasher drain.
To make the reverse osmosis (RO) drain connections:
A. Determine the location for your drain saddle (G) and then
make a mark on the drain pipe for the opening (1).
B. Use your drill and a 1/4 in. drill bit to drill a hole at the mark,
ensuring you only drill through one side of the drain pipe.
C. Find the half of the drain saddle (G) with the hole in the
center, remove the backing from the foam gasket, align the
gasket with the hole on the drain saddle (G), and stick the
adhesive side of the gasket to the drain saddle (G).
D. Position both halves of the drain saddle (G) on the drain pipe
with the saddle’s opening aligned over the drilled hole, and
insert your drill bit through the saddle (G) and drilled hole to
ensure proper alignment.
E. Secure both ends of the drain saddle (G) together using the
bolts and nuts, but do not overtighten.
F. Connect the RO water outlet tube (H) to the drain saddle (G).
To prevent water leakage, ensure the RO water outlet tube
(H) has been inserted into the pipe 0.6 inches.
About 0.6”
G
1
H

10
5. Flush the Filters
Follow this procedure each time you replace your filters.
IMPORTANT: Ensure water supply is o before you begin.
IMPORTANT: Flush ONLY the sediment, pre carbon, and post carbon filters. The reverse
osmosis (RO) filter should not be flushed.
A. Connect a filter (D) to the filter housing (C) by
twisting the filter (D) clockwise. C
D
B. Connect the tip of the shut-o valve tube (B)
to the left side of the filter housing (C).
C. Connect the filter flushing tube (A) to the
right side of the filter housing (C) and lay the
open end of the filter flushing tube (A) over a
sink or receptacle to collect water. A
C
B
D. Turn on water supply. Flush each filter for a
minimum of 5minutes. The recommended
amount is 1.5-3gallons of water (about
10 minutes) oruntil the water is clear in
appearance.
E. Shut o water supply and remove tube (B)
from filter housing.
B

11
6. Install the Filters and Complete the Installation
A. After flushing, twist each filter (D)
clockwise into the filter housings
located inside the dispenser cabinet.
The sediment filter goes on the left,
followed by the pre carbon, RO, and
post carbon filters.
D
B. Remove the safety plug from the
water inlet hole on the back of the
dispenser by pushing in the inlet hole
collar and then gently pulling out the
plug.
C. Connect the RO water outlet tube (H)
from the RO drain saddle (G) to the
RO water outlet.
D. Connect the tip of the shut-o valve
tube (B) into the water inlet hole on
the back of the dispenser. Then turn
on the main water supply and ensure
the valve in the tube (B) is on.
B
H

12
Operation
IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust
and odors can accumulate in the tank and lines. Dispense and dispose at least one liter of
water prior to drinking any water.
Turn the Dispenser On/O
IMPORTANT: Before activating heating and cooling switches, ensure water has filled the tanks inside the
dispenser in order to prevent dry heating.
1. Plug in the dispenser.
2. Allow water tanks to fill. During this time, the water production icon (6) will illuminate. When the tanks are
full, the icon light turns o.
3. Place a container under the water tap. Press the cold water button and dispense 1 liter of water. Discard water.
4. Place the container under the water tap. Press the hot water button and dispense 1 liter of water. Discard water.
5. Repeat steps 3 and 4 three more times.
6. To power on the cooling system, flip the cooling switch on the back of the dispenser to the On position.
The cold water button on the front of dispenser illuminates in blue indicating that the dispenser is cooling
water. The light changes to white when the cooling process is complete.
7. To power on the heating system, flip the heating switch on the back of the dispenser to the On position.
The hot water button on the front of the dispenser illuminates in red indicating that the dispenser is heating
water. The light changes to white when the heating process is complete.
Set the Time
1. Simultaneously press and hold the up and down arrow buttons for 3 seconds or until the time begins to
flash on the digital clock.
2. To set the hour, press the hot water button. The hour on the clock begins to flash. Use the up and down
arrow buttons to scroll to the correct hour.
3. To set the minutes, press the cold water button. The minutes on the clock begin to flash. Use the up and
down arrow buttons to scroll to the correct minutes.
4. Press the lock button until the selected time stops flashing. The time is now set.
Set the Cold Water Temperature Level
You can select from 3 dierent cold water dispensing temperature levels: C1 (cold), C2 (colder), and C3 (coldest).
Temperature Level Dispensing Temperature Range
C1 49°F to 55°F
C2 43°F to 49°F
C3 37°F to 43°F
NOTE: The default temperature dispensing level for cold water is C3 (coldest).
To change the cold water temperature dispensing level, please do the following:
1. Simultaneously press and hold the down arrow and cold water button for 3 seconds. The cold water button and
LED display showing current cold water temperature level begin to flash.
2. Press the up or down arrow to scroll through the 3 options. They will be displayed as C1, C2, and C3. After you have
reached the desired temperature level, quickly press the lock button. The new level is now set. It takes approximately
2 hours for the cold water temperature range to adjust to the new level. During the adjustment process, the cold
water light will illuminate in blue. Once the new level has been reached, the light will change to white.
NOTE: Cold water temperature is measured inside cold reservoir tank. Due to many variables, including but
not limited to, ambient temperature, water receptacle size/temperature, internal travel from reservoir
tank to dispense point, etc., temperature range of water dispensed will vary from stated range.

13
Dispense Cold Water
NOTE: Water will take approximately 1 hour after plugging in and turning on to become completely chilled.
1. Place a drinking glass or container under the tap and press the cold water button to dispense cold water.
2. Release the button when your container is full.
Disable Child Safety Lock and Dispense Hot Water
CAUTION: This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with
hot water. Keep children and pets away from the unit while dispensing. Never allow children to
dispense hot water without proper and direct supervision. Disable the heating feature by switching
the heating switch to the O position.
NOTE: Water will take approximately 15-20 minutes after plugging in and turning on to reach its hottest
temperature.
1. This water dispenser is equipped with a child safety feature in order to prevent inadvertent dispensing. To
disable the child safety lock feature, press the lock button.
2. To dispense hot water, place a drinking glass or container under the tap and press the hot water button.
3. Release the button when your container is full. Hot water button automatically relocks.
View Before and After Concentrations of TDS in Water
To see the ppm (parts per million) of TDS in prefiltered, then post-filtered water, do the following:
1. Simultaneously press the lock (8) and brew (10) buttons for 3 seconds.
2. The ppm of TDS present in incoming (prefiltered) water will appear in the LED display (4) for 3 seconds.
3. The ppm of TDS present in dispensed (post-filtered) water will then display for 17 seconds.
TDS Reduction Rates
Dispensed water should see a TDS reduction rate of up to 90%. Refer to the following table for estimated
before and after TDS levels.
NOTE: TDS reduction rates may vary based on the quality of source water.
Inlet Water TDS Level Dispensed Water TDS Level
250 25
200 20
150 15
100 10
50 5
10

14
Prepare Beverages
1. Pull out the brewer cup drawer and remove it completely from the dispenser.
2. Insert coee capsule of your choice (sold separately) and press it firmly into place until the needle has
fully punctured the bottom of the capsule, and the top of the capsule is level with the top of the drawer.
3. Slide the drawer into the dispenser and press until firmly in place. The 8-ounce serving size light will flash
on the display screen.
4. Press the Up arrow button or Down arrow button for your desired serving size of 6, 8, or 10 ounces. Once
your size selection has been made, press the Brew button (10). The screen will display the selected beverage
size and the coee button light will flash, then brewing will begin. There may be a short delay if hot water has
not reached the appropriate temperature. Brewing will commence as soon as temperature is reached.
5. If you don’t make a serving size selection within 5 seconds, the serving size light will turn o to prevent
inadvertent dispensing of hot water. To reactivate serving size selection, simply remove and reinsert
brewer cup drawer, then make your selection.
6. When brewing is complete, pull out the drawer and discard the used coee capsule, then reinsert drawer in
dispenser.
7. Approximately three 6- or 8-ounce servings, or two 10-ounce servings can be brewed consecutively. The
hot water button light will illuminate in red as water is heating for the next serving. Please note that it may
take a few minutes for the next brewing cycle to commence.

15
Troubleshooting
Problem Solution
The cold water is not cold.
•It takes up to one hour after setup to dispense cold water.
•Make sure the power cord is properly connected to a working outlet.
•Make sure the back of the dispenser is at least 20 cm from a wall and there is
free airflow on all 20 cm sides of the dispenser.
•Make sure green power switch on back of dispenser is On.
•If water still isn’t cold, call customer service at [phone] for assistance.
The hot water is not hot.
•It takes 15-20 minutes after setup to dispense hot water.
•Make sure the power cord is properly connected to a working outlet.
•Make sure red power switch on back of dispenser is On.
Water flow is slow. •Water output may slow or decrease if there has been continuous dispensing.
Allow tanks to refill before dispensing.
The night light is not
working.
•Make sure the power cord is properly connected to a working outlet
•Make sure the night light power switch on back of dispenser is On.
The dispenser is noisy. •Ensure the dispenser is located on a level surface.
•The heating tube may be generating a slight noise. This is normal.
There is water leakage.
If the LED display is flashing, a leak was detected.
•The tubing or piping is not connected properly. Check all water connections and
tubes to ensure proper connections.
•The water and/or PE tubes have burst. Turn o water supply and replace
immediately.
The dispenser is not
dispensing water.
•The dispenser has become too cold and the lines are blocked by ice. Turn o
the cooling switch for at least 4 hours to allow the water in the lines to thaw.
The dispenser is not
dispensing coee or is
dispensing coee slowly.
•Brew coee without using coee capsules several times, or until water
dispenses normally from coee brewer.
Cleaning and Maintenance
The dispenser runs on a continuous UV cleaning cycle.
It works for 40 minutes (UV icon on the display is on), turns o for 140 minutes, and then cycles back on again as
long as the dispenser is plugged in and on. You can dispense water when the UV light is on.
Care and Maintenance
•Brewer cup drawer and drip trays are dishwasher safe; however, washing in high temperatures or using a
“sanitize” cycle is not advised.
•Keep this dispenser in a dry and cool place and avoid direct sunshine.
•Ensure the back of the dispenser is at least 8 in. (20 cm) away from the wall.
•Never put the dispenser on paper or foam, which may store water and then cause creepage. Never put
anything flammable beside this machine.
•Do not use the dispenser outdoors or in a place that can be splashed by water.
•If the dispenser is not in use for longer than a 24-hour period, turn o heating and cooling switches to save
power and drain any remaining water.
•Empty and clean the drip tray and grid as needed.

16
Filter Replacement Schedule
Filter Type Model No. Replacement Schedule Function
Sediment NFMPP5M 6-12 months or 950 gallons
Performs coarse filtration of inlet water,
removing sand, rust, dirt, and other
suspended solids.
Pre Carbon NFMGAC 6-12 months or 950 gallons Removes chlorine, and other unpleasant
tastes and odors.
Reverse Osmosis
(RO) NFMRO75GPD
6-12 months or 1,900 gallons
Removes contaminants, including lead,
arsenic, fluoride, and TDS.
Post Carbon NFMCTO5MS4 6-12 months or 950 gallons Performs final polish, removing any
residual impurities.
Replace the Filters
IMPORTANT: Only replace the filters with new filters designed for this dispenser. Any other type of filter will damage the machine and void any
warranty.
When the PCB (2) and RO (3) filter indicator lights steadily illuminate and the dispenser beeps, the filters have expired and must be replaced
immediately.
To replace, do the following:
1. Shut o the water supply.
2. To flush your new filters, follow the instructions on page 8, “Flush the Filters.”
3. Remove the expired filters and replace with new filters. Ensure the filters are installed as follows, from left to right: sediment filter, pre carbon
filter, RO filter, and post carbon filter.
4. After replacing the filter element, press the up arrow (1) for approximately 3 seconds to reset the filter indicators and turn o the beeping.
Filter Specifications
Sediment Filter Pre Carbon Filter
(Sediment, Dirt and Rust Removal) (Chlorine, Taste and Odor Reduction)
Filter Capacity 950 Gallons Filter Capacity 950 Gallons
Flow Rate 0.8 GPM Flow Rate 0.8 GPM
Suggested PSI 14.5 - 58 psi Suggested PSI 14.5 - 58 psi
Temperature 33 - 100 °F Temperature 33 - 100 °F
RO Filter Post Carbon Filter
(Heavy Metal and TDS Removal) (Final Polish)
Filter Capacity 1,900 Gallons Filter Capacity 950 Gallons
Flow Rate 0.035 GPM Flow Rate 0.8 GPM
Suggested PSI 58 - 116 psi Suggested PSI 14.5 - 58 psi
Temperature 33 - 100 °F Temperature 33 - 100 °F

17

18

19

©2023 Brio Water Technology, Inc.
Contact Us
Call: [phone]