BRITISH RECYCLED PLASTIC Adult Picnic Table User manual

BRITISH RECYCLED PLASTIC Unit 8C, Top Land Country Business Park, Cragg Road, Mytholmroyd, HX7 5RW Tel: [phone] Email: [email protected] britishrecycledplastic.co.uk
Adult Picnic Table Assembly Instructions
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND FOLLOW THE ASSEMBLY DRAWINGS.
WE WILL NOT ACCEPT ANY CLAIMS IF THIS PRODUCT IS WRONGLY ASSEMBLED.
Parts Supplied Tools Required
a) 2 × A-Frame supports
b) 10 × Seat & table slats [labelled 1 to 10]
c) 2 × Angle braces
d) 2 × Seat ties
e) 3 × Table tie
f) 2 × Outer table ties
g) 2 × Metal table brackets
h) 44 × 90mm screws
i) 16 × 70mm screws
j) 18 × 50mm screws
Power drill with Philips screwdriver bit
Measuring tape
Straight edge
2 Person Operation
2.
3.
1.
2 × Seat slats [2&9]
8 × 90mm screws
2 × A-Frames
2 × Seat slats [1&10]
8 × 90mm screws
2 × Table slats [3&8]
8 × 90mm screws
• Position seat slats [2&9] with a 25mm
gap between slats.
• Square the ends with a straight edge.
• Fix with 90mm screws.
• Position outer table slats 3 and 8 with a 10mm overhang
and 245mm from horizontal support to end of slat.
• Loosely secure outer holes with 90mm screws.
• Ensure slats are square by measuring the
diagonals. The diagonals should measure the same.
• Tighten the outer screws once the table is square.
• Fix inner holes with 90mm screws.
•StandendA-Framesuprightonaatsurfacewithhorizontal
support facings on the inside.
• Position seat slats 1 and 10 as the diagram, and locate pilot
holes in the A-Frames through the predrilled outer holes of the
slats, secure loosely using 90mm screws - but do not fully
tighten. (This will give a 10mm overhang and 245mm from
horizontal support to end of slat).
• Ensure that the frames are square by measuring across
the diagonals. The diagonals should measure the same.
• Tighten the outer screws once the table is square.
• Fix the inner holes with 90mm screws.

BRITISH RECYCLED PLASTIC Unit 8C, Top Land Country Business Park, Cragg Road, Mytholmroyd, HX7 5RW Tel: [phone] Email: [email protected] britishrecycledplastic.co.uk
Adult Picnic Table Assembly Instructions
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND FOLLOW THE ASSEMBLY DRAWINGS.
WE WILL NOT ACCEPT ANY CLAIMS IF THIS PRODUCT IS WRONGLY ASSEMBLED.
6.
4.
5.
7.
2 × Angle braces
2 × Seat braces
12 × 90mm screws
4 × Table slats [4,5,6&7]
16 × 90mm screws
2 × Seat ties
3 × Table tie
14 × 70mm screws
12 × 50mm screws
6 × 70mm screws
• Fix the angle braces to the A-frame with 90mm screws (red dashed lines).
• These braces need to be pushed down tight to the underside of the table tie.
• Fix the seat braces to the A-frame with 2 × 90mm screws at each end (green
dashed lines). Ensure the brace is positioned at the same height as the centre tie.
• Turn the table over on to its top.
• Fix the seat ties in the centre of the seat slats
with 70mm screws (4 screws per tie).
• Fix the table tie in the centre of the table slats
with 70mm screws (1 screw per slat).
• Ensure that the two central holes can be viewed
from the top (see stage 7).
• Fix the two table ties near the ends of the slats
and secure with one 50mm screw per slat
(green dashed lines).
• Position the 4 remaining slats [4,5,6&7] with equal gaps.
• Ensure there is a large enough gap between the two
 centralslatstoallowforscrewstoxtheanglebrace
(see stage 7).
• Square the ends with a straight edge.
• Fix with 90mm screws.
• Turn the table back on to its legs.
• Fix the angle braces to the table tie between the
central table slats with 70mm screws.
• Fix the seat braces (through the ties) through the
gap in the seat slats with 2 × 70mm screws in
each (blue dashed lines).