Broadcom F5D7010CE2 User manual

CETECOM Inc.
CETECOM Inc.
411 Dixon Landing Road, Milpitas, CA-95035, USA
Phone: [phone] Fax: [phone]
www.cetecom.com
Issued test report consists of 25 Pages Page 1 (25)
Test report no.: EMC_381EN489-17_2002
ETSI EN 301 489-17 V1.1.1 (2000-09)
(BCM94306CB)
FCC LISTED, REG. NO.: 101450
&
RECOGNIZED BY INDUSTRY CANADA
IC – 3925

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 2 (25)
Table of Contents
1 General information
1.1 Notes
1.2 Testing laboratory
1.3 Details of applicant
1.4 Application details
1.5 Test item
1.6 Test standards
2 Technical test
2.1 Summary of test results
2.2 Test report
1 General information
1.1 Notes
The test results of this test report relate exclusively to the test item specified in 1.5. The CETECOM
Inc. USA does not assume responsibility for any conclusions and generalisations drawn from the test
results with regard to other specimens or samples of the type of the equipment represented by the test
item. The test report may only be reproduced or published in full. Reproduction or publication of
extracts from the report requires the prior written approval of the CETECOM Inc USA.
TEST REPORT PREPARED BY:
EMC Engineer: Philip Kim
1.2 Testing laboratory
CETECOM Inc.
411 Dixon Landing Road, Milpitas, CA-95035, USA
Phone: [phone] Fax: [phone]
E-mail: [email protected]
Internet: www.cetecom.com

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 3 (25)
1.3 Details of applicant
Name : Broadcom corporation
Street : 190 Mathilda Place
City / Zip Code : Sunnyvale, 94086
Country : USA
Contact : Chris McGough
Telephone : [phone]
Tele-fax : [phone]
e-mail : [e-mail]
1.4 Application details
Date of receipt of application : 2002-12-19
Date of receipt test item : 2002-11-21
Date of test : 2002-12-06, 2002-12-13 and 2002-12-14
1.5 Test item
Manufacturer : See Applicant
Model No. : BCM94306CB
Description : 54g Wireless Lan cardbus PC card
Additional information
Frequency : 2412MHz – 2472MHz
Type of modulation : OFDM (orthognal frequency division multiplexing)
Number of channels : 13
Antenna : 1dBi external antenna
Power supply : From Host
Output power : 16.09dBm (40.64mW) max. EIRP
Extreme temp. Tolerance : 0 to +50 oC
1.6 Test standards: ETSI EN 301 489-17 V1.1.1 (2002-09)
ETSI EN 301 489-1 V1.2.1 (2000-08)

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 4 (25)
2 Technical test
2.1 Summary of test results
No deviations from the technical specification(s) were ascertained in the course of the tests
Performed
Final Verdict:
(only “passed” if all single measurements are “passed”) Passed
Technical responsibility for area of testing:
2003-01-10 EMC & Radio Lothar Schmidt (Manager)
Date Section Name Signature
Responsible for test report and project leader:
2003-01-10 EMC & Radio Philip Kim (EMC Engineer)
Date Section Name Signature

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 5 (25)
2.2 Test report
TEST REPORT
Test report no. : EMC_381EN489-17_2002
(BCM94306CB)

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 6 (25)
SUMMARY OF TEST RESULTS 7
EMISSION(EMI) 7
IMMUNITY(EMS) 7
GENERAL PERFORMANCE CTIRERIA 8
EMISSION TEST: 9
RADIATED EMISSIONS 9
AC LINE CONDUCTED EMISSIONS 10
HARMONIC CURRENT EMISSIONS 11
FLICKER AND VOLTAGE FLUCTUATION 12
IMMUNITY TEST: 13
RADIATED, RF ELECTROMAGNETIC FIELDS 13
RF COMMON MODE 14
ELECTROSTATIC DISCHARGE 15
FAST TRANSIENTS COMMON MODE 16
SURGES COMMON & DIFFERENTIAL MODE (1-phase) 17
VOLTAGE DIPS 18
PLOTS 19
TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS 21
PHOTOGRAPHS 24

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 7 (25)
SUMMARY OF TEST RESULTS
EMISSION (EMI)
EMI
Phenomenon
Port Requirements EUT set-
up
Result Applicability
Standard Basic standard
Conducted
Interference voltage,
0.15 – 30*MHz
AC Mains
ETSI EN 301 489-1,
2000-08
Chap. 8.4
EN 55022:1998
+Corr.2001 + A1:2000 na Complies Not Applicable
Radiated
Interference Field
Strength
30 – 1000*MHz
Enclosure
ETSI EN 301 489-1,
2000-08
Chap. 8.2
EN 55022:1998
+Corr.2001 + A1:2000 na Complies Applicable
Harmonic Current
Emissions
AC mains
input port
ETSI EN 301 489-1,
2000-08
Chap. 8.5
EN 61000-3-2: 2000 na Complies Not Applicable
Flicker & Voltage
Fluctuation
AC mains
input port
ETSI EN 301 489-1,
2000-08
Chap. 8.6
EN 61000-3-3: 2000 na Complies Not Applicable
IMMUNITY (EMS)
EMS
Phenomenon
Port Requirements EUT set-
up
Result Applicability
Standard Basic standard
Electrostatic
discharge
(ESD)
Enclosure
ETSI EN 301 489-1,
2000-08
Chap. 9.3
--
EN 61000-4-2: 1995
+A1: 1998+A2:2001 na Complies Applicable
RF-electro-magnetic
field Enclosure
ETSI EN 301 489-1,
2000-08
Chap. 9.2
--
EN 61000-4-3: 1996
+A1: 1998+A2:2001 na Complies Applicable
Fast transients,
BURST
Powerline
AC / DC
ETSI EN 301 489-1,
2000-08
Chap. 9.4
--
EN 61000-4-4: 1995
+A1: 2001 na Complies Not Applicable
Surge Powerline
(1 phase)
ETSI EN 301 489-1,
2000-08
Chap. 9.8
--
EN 61000-4-5: 1995
+A1: 2001 na Complies Not Applicable
Transients & Surges
vehicular
evironment
Powerline
(car
charger)
ETSI EN 301 489-1,
2000-08
Chap. 9.6
--
ISO 7637-1/2:1990
(12/24VDC) na Complies Not Applicable
RF Common mode
Powerline
AC/DC
signal lines
ETSI EN 301 489-1,
2000-08
Chap. 9.5
--
EN 61000-4-6: 1996
+A1: 2001 na Complies Not Applicable
Vol. Dips,
interruptions &
fluctuations (AC
Power)
Input &
output AC
ports only
ETSI EN 301 489-1,
2000-08
Chap. 9.7
--
EN 61000-4-11: 1994
+A1: 2001 na Complies Not Applicable
na=not applicable

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 8 (25)
GENERAL PERFORMANCE CRITERIA
The performance criteria are:
-performance criteria A for immunity tests with phenomena of a continuous nature;
Communication between the BCM94306CB and BCM94306MP in the form of pings should not drop
during the test.
-performance criteria B for immunity tests with phenomena of a transient nature;
N/A
-performance criteria C for immunity tests with power interruptions exceeding a certain time.
N/A
NOTE: For details see subclause 6.2 ETSI EN 301 489-17

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 9 (25)
EMISSION TEST:
RADIATED EMISSIONS
This test assessses the ability of ancilliary equipment to limit their internal noise from being radiated from the enclosure.
According to EMC basic standard (EN 55022)
Measurement according to EMC basic standard, but performed in the anechoic chamber with a reduced measuring distance of
3m. The reduction of the measuring distance and the existing floor absorber are corrected with the chamber factor (Method
Dr. Garn, Austrian Research Centre, Seibersdorf). The test results of the anechoic chamber correspond to the 10m-OATS
results
Test setup
EUT was setup in an anechoic chamber
Limits
Freq. Range Limit (Quasi peak)
30MHz – 230MHz 30dBµV/m
230MHz – 1000MHz 37dBµV/m
EUT Type and
S/N or EUT set-up
no.
Set.
Plot
No.
receiving
antenna
directed to
angle of
turntable
polari-sation
(h / v)
comment
(e.g. operating mode or
operating mode no.)
result
(passed /
failed)
1.1 -- 0 º - 360º h/v EUT operating mode 3 Passed
Remarks: All measurements were carried out in peak mode. As long as the values stay under the average limit line
No QP measurements are carried out.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 10 (25)
AC LINE CONDUCTED EMISSIONS
According to EMC basic standard (EN 55022 [7] Class-B)
1.For the table top EUT the distance to the reference ground plane (wall) should be 40 cm.
2.AC input line plugged into LISN
EUT Operating mode
Tx at middle. channel
Plot no. Powerline
(L,N)
EUT operating mode or
operating mode no.
Detector
(Peak,
AV, QP)
Additional (scan-) information
(e.g. Pre-test Fastscan,
Maxhold,
Final measurement)
Result
(passed /
failed )
-- L+N QP Final measurement N/A
Note: This test does not apply due to the fact that EUT’s power is host dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 11 (25)
HARMONIC CURRENT EMISSIONS
This test was performed as per EMC Basic Standard EN 61000-3-2(Dec-2000)
EUT Operating mode
Tx at middle. channel
Plot No. Port EUT operating mode or
operating mode no.
Result
(passed / failed )
-- AC input Tx at mid. channel N/A
Note: This test does not apply due to the fact that EUT’s power is host dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 12 (25)
FLICKER AND VOLTAGE FLUCTUATION
This test was performed as per EMC Basic Standard EN 61000-3-3
EUT Operating mode
Tx at middle. channel
Plot No. Port EUT operating mode or
operating mode no.
Result
(passed / failed )
-- AC input Tx at mid. channel N/A
Note: This test does not apply due to the fact that EUT’s power is host dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 13 (25)
IMMUNITY TEST:
RADIATED, RF ELECTROMAGNETIC FIELDS
According to EMC basic standard (EN 61000-4-3[9])
· The distance between the turn-table axis and TX-antenna is 3m.
· Field strength = 3V/m
· Start Frequency = 80MHz Stop Frequency = 1000MHz
· Frequency Step = lin 1MHz
· Modulation = AM, 1KHz, 80%
Failure Criteria
Describe applicable failure criteria for EUT
Example
1.Continuous data transfer between EUT and Mini PCI Access Point
2.Transmitting following data: 65 bytes from 192.168.1.1 icmp_seg = xxx + H = 255 time = xxx
3.If connection drops then the the program will display “Request Timed out”
Failure Criteria obesrved
Describe how failure criteria was observed
Example
1. Observe continuous scrolling “# ” on the screen
Performance criteria A observed
Plot
no.
Antenna
Polarity Radiation to Reaction of the EUT During and after test Result
5.1 vertical Front No reactions recognized passed
5.2 horizontal Front No reactions recognized passed

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 14 (25)
RF COMMON MODE
According to EMC basic standard (EN 61000-4-6[10])
Start Frequency = 150KHz Stop Frequency = 80MHz
Frequency Step = 50KHz in the range of 150KHz – 5MHz
1% increment in the range of 5MHz – 80MHz
Field strength = 3V/m
Modulation = AM, 1KHz, 80%
Test setup
Injection via CDN or BIC clamp
Failure Criteria
Failure Criteria obesrved
Plot no. Injection on Injection Via Reaction of EUT during and after test Result
-- AC input power line CDN No reactions recognized N/A
Performace criteria A observed
Note: This test does not apply due to the fact that EUT’s power suuply is host
dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 15 (25)
ELECTROSTATIC DISCHARGE
According to EMC basic standard (EN 61000-4-2[10])
For the table top EUT the distance to the reference ground plane should be 80 cm.
Direct contact discharge on conducting surfaces of EUT
Indirect air discharge on insulating surfaces of EUT
±2kV, ±4kV direct discharge & ±2kV, ±4kV, ±8KV air discharger
Test setup
Failure Criteria
Failure Criteria obesrved
10 Single impulses at each test point and for each test voltage
Contact discharge
to conducted surfaces and to coupling planes
Air discharge
at insulating surfaces
Direct contact discharge Indirect contact discharge
Test voltage Reaction of EUT / result Reaction of EUT / result Reaction of EUT / result
+2 kV
-2 kV
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
+4 kV
-4 kV
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
n.r.r. passed
+6 kV
-6 kV
-
-
-
-
-
-
+8 kV
-8 kV
-
-
-
-
n.r.r. passed
n.r.r. passed
Remarks: n.r.r = no reaction recognized
Performance Criteria A observed

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 16 (25)
FAST TRANSIENTS COMMON MODE
According to EMC basic standard (EN 61000-4-4[11])
1.For the table top EUT the distance to the reference ground plane should be 80 cm.
2.The test level for ac mains power input ports shall be 1KV open curcuit.
Test setup
Burst on Power Line (direct injection)
Failure Criteria
Failure Criteria obesrved
Adjustment on UCS 500 M4:
Trigger: "AUTO", Burst length: 15 ms
testing time: n60 s for every voltage and polarity
¨120 s for every voltage and polarity
Testing on power
line(direct injection) reaction of the test object during and after test result
Test
voltage
repetition
frequency
L1=> GND
(+=>
GND)
L2=> GND L3=>
GND
N =>
GND
PE=>
GND
L1, N,
=>
GND
-0,5 kV
+0,5 kV
5 kHz
5 kHz
n.r.r.
n.r.r
N/A
N/A
N/A
N/A
n.r.r.
n.r.r.
N/A
N/A
n.r.r.
n.r.r.
passed
passed
-1,0 kV
+1,0 kV
5 kHz
5 kHz
n.r.r.
n.r.r
N/A
N/A
N/A
N/A
n.r.r.
n.r.r.
N/A
N/A
n.r.r.
n.r.r.
passed
passed
n.r.r = no reaction recognized, N/A = not applicable
Performance Criteria A observed
Note: This test does not apply due to the fact that EUT’s power suuply is host
dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 17 (25)
SURGES COMMON & DIFFERENTIAL MODE (1-phase)
According to EMC basic standard (EN 61000-4-5[14])
1.For the table top EUT the distance to the reference ground plane should be 80 cm.
2.1KV open circuit for common mode & 0.5KV open circuit for differential mode.
Failure Criteria
Failure Criteria obesrved
5 pulses for each polarity and test voltage, alternating negative/positive, triggered in case of AC-powerline: 0°, 45°, 90°, 180°,
270° referred to the line frequency (L1),
repetition rate is 1 per min.
Test
voltage
reaction of the test object during and after test by trigger angle/pulse no.
(coupling on DC-lines => trigger angle not relevant)
Result
0°/pulse no. 1,
2
45°/no. 3, 4 90°/no. 5, 6 180°/no. 7, 8 270°/no. 9, 10
capacitive coupling on AC lines: L 1 => N or DC lines + => - (R = Ri = 2 W/ C = 18 µF )
-0,5 kV
+0,5 kV
no reaction
recognized
no reaction
recognized
no reaction
recognized
no reaction
recognized
no reaction
recognized
passed
-1,0 kV
+1,0 kV
no reaction
recognized
no reaction
recognized
no reaction
recognized
no reaction
recognized
no reaction
recognized
passed
-2,0 kV
+2,0 kV N/A N/A N/A N/A N/A --
- kV
+ kV N/A N/A N/A N/A N/A --
Performance Criteria A observed
Note: This test does not apply due to the fact that EUT’s power suuply is host
dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 18 (25)
VOLTAGE DIPS
According to EMC basic standard (EN 61000-4-11 [13])
1.For the table top EUT the distance to the reference ground plane should be 80 cm.
2.The test level shall be – a vol. Reduction of the supply vol. of 30% for 10ms; 60% for 100ms
and >95% for 5000ms
Failure Criteria
Failure Criteria obesrved
for each test 3 repetitions in an interval of 10 s
time for decrease or increase of supply voltage: T down/up < 5 µs (due to switching
ominal
supply
voltage
start by trigger
angle
(AC)
duration of
test voltage test voltage reaction of EUT during and after test result
U 1T U2 U 2
100% UN:
n230V
¨
0°° 10 ms
70% UN
n161 V
¨
n.r.r – performance criteria A
observed N/A
100% UN:
n230V
¨
0°° 100 ms
40% UN
n92 V
¨
n.r.r – performance criteria A
observed N/A
100% UN:
n230V
¨
0°° 5000 ms
0% UN
0 V performance criteria C observed N/A
n.r.r – no reaction recognized
Note: This test does not apply due to the fact that EUT’s power suuply is host
dependant.

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 19 (25)
PLOTS
Plot 1.1
-20
0
20
40
60
80
90
Level [dBµV/m]
30M 50M 70M 100M 200M 300M 500M 700M 1G
Frequency [Hz]
Marker: 455.711423 MHz 33.24 dBµV/m

CETECOM Inc.
Test report no.:EMC_381EN489-17_2002 Issue date:2003-01-10 Page 20 (25)
Plot 5.1
Polarization: Vertical
-0.5
0.0
0.5
1.0
1.5
EUT Nogo [-]
80M100M 200M 300M 400M 500M600M 800M 1G
Frequency [Hz]
Marker: 1 GHz 0 -
0
5
10
15
20
Immunity Level [V/m]
80M 100M 200M 300M 400M 500M600M 800M 1G
Frequency [Hz]
Marker: 1 GHz 3.018376 V/m