brondell BF200 User manual

Questions about installation? Call our customer service department at 888-542-3355 or visit brondell.com
BF200/BF400 Filtered Water Faucet Installation
Top Spout
Main Body
Top Cap
Large Rubber Washer
Small Rubber Washer
Lock Washer
Locking Nut
Escutcheon
Counter Top
Plastic Washer
(connected to faucet)
1/4” Tube
Installing the Faucet
1. Unpack the faucet and insert the Top Spout into the Main Body by
pushing down until fully inserted, then screw the Top Cap clockwise
until secured in place.
2. Cut zip tie on the blue water connection tubing and unroll to
straighten tubing. Be careful not to cut the tube when removing the
zip tie.
3. Install the Escutcheon (faucet base), curved lip side down, by
inserting the blue tubing through the Escutcheon and the Large
Rubber Washer and push both all the way up until adjacent to the
Main Body.
4. Install the faucet on top of the countertop or sink and feed the blue
tubing through the hole to the cabinet below. Slide the large Plastic
Washer and Small Rubber Washer as shown to the left up through the
blue tubing until snug against the bottom of the countertop or sink
hole.
5. Install the Lock Washer and the Locking Nut the same way and
tighten until the Plastic Washer and Small Rubber Washer are holding
the faucet assembly firmly in place. The faucet is now installed!

Questions about installation? Call our customer service department at 888-542-3355 or visit brondell.com
Installing the Faucet
1. Unpack the faucet and insert the Top Spout into the Main Body by
pushing down until fully inserted, then screw the Top Cap clockwise
until secured in place.
2. Cut zip tie on the blue water connection tubing and unroll to
straighten tubing. Be careful not to cut the tube when removing the
zip tie.
3. Install the Escutcheon (faucet base), curved lip side down, by
inserting the blue tubing through the Escutcheon and the Large
Rubber Washer and push both all the way up until adjacent to the
Main Body.
4. Install the faucet on top of the countertop or sink and feed the blue
tubing through the hole to the cabinet below. Slide the large Plastic
Washer and Small Rubber Washer as shown to the left up through the
blue tubing until snug against the bottom of the countertop or sink
hole.
5. Install the Lock Washer and the Locking Nut the same way and
tighten until the Plastic Washer and Small Rubber Washer are holding
the faucet assembly firmly in place. The faucet is now installed!
6. Pull the plastic tab out from the Battery Seat to activate the LED
Indicator. The LED light will blink red once, blue once, and then will
be ready to go.
Counter Top
Large Rubber Washer
Top Spout
LED Display
Escutcheon
(connected to faucet)
Locking Nut
Plastic Washer
1/4" Tube
Small Rubber Washer
Lock Washer
Main Body
Top Cap
Battery Seat
CR2032
Battery Replacing the Battery (with
each filter change)
Replace the battery in the faucet LED indicator
to reset the filter change reminder. Use the
new CR2032 battery included with your
replacement filter set.
1. Under the Faucet Handle, locate the black
rubber Battery Seat. Grasp it from the sides
and pull down.
2. Remove the old battery by gently lifting the
silver metal tab and sliding the battery out
of the Battery Seat. Wait 30 seconds before
inserting the new battery.
3. Insert the new CR2032 battery by sliding
the battery under the silver tab, making sure
that the “+” sign and CR2032 are facing
towards you.
4. Push the Battery Seat back up into the
Faucet Handle.
Step 1
Step 3
Step 4
For California Residents
CR2032 batteries contain Perchlorate Material - special handling may apply.
Visit http://www.dtsc.ca.gov/hazardouswaste/perchlorate for more information.
BF100/BF300 Filtered Water Faucet
Installation & Battery Replacement