Brother MFC-J3540DW User manual

Quick Setup Guide
Read the Product Safety Guide first, then read this Quick Setup Guide for the correct installation procedure.
CHN-ENG
Version 0
EN
1Unpack the machine and check the components
Remove the protective tape or film covering the machine and the supplies.
MFC-J3540DW / MFC-J3940DW
NOTE
• Save all packing materials and the box in case you must ship your
machine.
• For a network connection you must purchase a network interface
cable. A USB cable is included with your machine.
USB cable
We recommend using a USB 2.0 cable (Type A/B) that is no more than
2 metres long.
Ethernet (Network) cable
Use a straight-through Category 5 (or greater) twisted-pair cable for
10BASE-T or 100BASE-TX Fast Ethernet Network.
NOTE
You can adjust the control panel
angle to read the LCD more easily.
NOTE
The first time you install a set
of ink cartridges the machine
will use an amount of ink to fill
the ink delivery tubes for high
quality printouts. This process
will only happen once.
Open the ink cartridge cover.
Remove the orange protective part from the machine. Follow
the LCD instructions to store the orange protective part inside
the machine. If you must transport the machine, remove the ink
cartridges and replace this part.
Operation Videos:
www.95105369.com
Pull the paper tray completely
out of the machine as shown
by the arrow.
Fan the paper well. Load the paper in the tray
and adjust the paper guides.
Slowly push the paper tray
completely into the machine.
Pull out the paper support until
it locks into place.
Quickly shake just the
black ink cartridge
horizontally 15 times as
shown, before inserting
it into the machine.
Follow the LCD instructions
to install the ink cartridges.
Close the ink cartridge
cover. The machine will
prepare the ink tube
system for printing.
Follow the LCD instructions to set
the date and time.
After setting the date and time, you
can set the Brother LCD Message
defaults.
Follow the LCD instructions,
and then press [S t a r t].
The machine prints the Print
Quality Check Sheet.
Follow the LCD instructions and
check the quality of the four
colour blocks on the sheet, and
then start the cleaning procedure
if required.
Follow the LCD instructions
to print the Adjustment
Sheet. The black circle mark
is located in the upper right
corner of the sheet.
Place the Adjustment Sheet
face down on the scanner
glass. Make sure the black
circle is in the upper left corner
of the scanner glass.
Follow the LCD instructions
and complete adjusting the
alignment.
When finished, remove the
Adjustment Sheet from the
scanner glass.
After finishing the machine setup, you can change the paper type or size. For more information
about paper handling, see the Online User’s Guide at www.95105369.com.
2Load plain A4 paper
4Install the inbox ink cartridges
3Connect the power cord
6Check the print quality 7Adjust the print alignment (recommended)
To adjust the print alignment before using your machine, press [S t a r t].
5Set the date and
time
• Most of the machine illustrations in this Quick Setup Guide show the MFC-J3940DW.
• The images in this guide are for illustration purposes only and may differ from the actual products.
Do not exceed
this mark (bbb).
OK Poor
Installation & Using Videos
1
Inbox Ink
Cartridges
User's Guides Power Cord
USB Cable Maintenance Sheet

Can’t Connect? Check the following:
Wireless network
Wired network
USB connection
Restart your wireless access point/
router (if possible). If still not successful, go to 11 .
Disconnect the cable. If still not successful, visit www.95105369.
com for FAQs and Troubleshooting.
Restart your machine and
computer, and then go to 10 .
Follow the LCD instructions to configure the machine settings.
• (MFC-J3940DW only) Configure the tray settings and check the paper
orientation information.
• Check the software installation information.
Visit setup.brother.com to download and
install Brother software.
Follow the on-screen instructions and
prompts.
NOTE
For Wired Network Connection and USB
Connection, locate the correct port (based on
the cable you are using) inside the machine
as shown.
Setup Finished
You can now print and scan using your machine.
To check for the latest firmware, visit support.brother.com/up7.
Find your SSID (Network Name) and Network Key
(Password) on your wireless access point/router
and write them in the table provided below.
SSID (Network Name)
Network Key (Password)
Go to your machine,
and press
>
[Find Wi-Fi Network] >
[Yes].
Go to 10 to install software.
SSID: XXXXXXX
Network Key: XXXX
If you cannot find this information, ask your network
administrator or wireless access point/router
manufacturer.
If setup is not successful, restart
your Brother machine and your
wireless access point/router, and
repeat 11 .
Important Notice for Network Security:
The default password to manage this machine’s settings is located
on the back of the machine and marked “Pwd”. We recommend
immediately changing the default password to protect your machine from
unauthorised access.
For detailed machine information and product specifications, see the Online User's Guide at www.95105369.com. © 2021 Brother Industries, Ltd. All rights reserved.
11 Manual wireless setup
If the wireless setup is not successful, try to set up the connection manually.
10 Connect your computer or mobile device to your machine
Follow these steps to complete the setup using one of the connection types available on your machine.
9Connect the telephone line cord
If you are not using your machine as a fax, go to 10 . For more information on using the fax feature, see the Online User’s Guide.
8Machine settings
setup.brother.com
Select the SSID (Network
Name) for your access point/
router and enter the Network Key
(Password).
When the wireless setup is
successful, the LCD displays
[Connected].
Lift the scanner cover. Close the scanner cover.
Connect the telephone line cord. Use the socket
marked LINE and guide the cord out the back of the
machine.
The telephone line cord is not included in the box.
2
兄弟畅享印(WeChat Mini Program)
You can print photos and documents using
WeChat application "兄弟畅享印", without the need
to install an app or a driver. Register your machine
before using this feature for the first time. Visit the
QR code on the right for the instruction.