BRP Rotax 4-TEC 150 User manual

*461153
Information Center
User’s Guide
ROTAX 4-TEC 150, 200, 250 (ECT)
Rev. A
ACE 60, 90 (ECT)

1
Safety Information
This user’s guide may contain the following safety messages:
Thisuser’sguidecontainsinformationtopreventpersonalinjuryanddamage
to equipment. Use this guide in combination with the boat and outboard op-
erator’s guides. Always follow safety and operation information.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moder-
ate personal injury.
NOTICE
Indicates an instruction which, if not followed, could severely damage engine compo-
nents or other property.

2
TABLE OF CONTENTS
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SINGLE ENGINE INFORMATION CENTER . . . . . . . . . . . . . . . . . .4
DUAL ENGINE INFORMATION CENTER . . . . . . . . . . . . . . . . . . . .4
TACHOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SPEEDOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
INDICATOR LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FUEL LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
NUMERICAL DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MULTIFUNCTION DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DEPTH SOUNDER INDICATOR . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOUR METER DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
COMPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ENGINE IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SELECTING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CHANGING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CHANGING NUMERICAL DISPLAY INDICATION . . . . . . . . . . . . .16
MAIN MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
DOCKING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
SKI MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CRUISE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
ECO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ECO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
DISPLAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
FAULT CODE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SETTINGS MENU - ENGINE OFF . . . . . . . . . . . . . . . . . . . . . . . . .24
SETTINGS MENU - ENGINE IDLE . . . . . . . . . . . . . . . . . . . . . . . . .25
INR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
INR OVERRIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
INR NEUTRAL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

3
Product Description
The Rotax®Information Center is a cluster of information gauges, indicator
lights and a digital screen to display information to the operator.
Text messages can be displayed in English, French, or Spanish, and the
units of measurement can be displayed in metric or imperial.
The operator can view several indications such as RPM, fuel level, and en-
gine temperature. The information center can also be used to navigate
through and select several functions, modes of operation, and change cer-
tain settings and system parameters.
Indicator lamps advise the operator of selected functions or warning indica-
tors.
The information center incorporates a GPS (global positioning system) com-
pass and speedometer indications, and provides signals to other systems as
required.
If a fault is detected during the self-test function, an error message will be dis-
played, an indicator light may come on, and an audible signal (beep code)
may be heard.
At start-up, all LCD segments and indicator lights will turn on for 3 seconds.
This allows the user to validate proper operation.
NOTE: The information center illuminates when the navigation lights are
used.

4
Single Engine Information Center
Dual Engine Information Center
TachometerSpeedometer Fuel Level
Digital Screen
Numerical Display
Multifunction Display
Depth Sounder Indicator Hour Meter Display
Indicator
Lights Indicator Lights
461153-01
Shift Indicator iNR
Port Fuel Level
Digital Screen
Numerical Display
Multifunction DisplayDepth Sounder Indicator
Hour Meter Display
Tachometer Starboard
Tachometer
(port and starboard
Engine Indicator
Indicator
Lights Indicator Lights
461153-02
Shift Indicator (iNR)

5
Tachometer
The tachometer(s) provide an analog indication of the revolutions per min-
ute (RPM) of the engine(s).
Speedometer
The speedometer provides an indication of speed in miles per hour (MPH)
or kilometers per hour (km/h).
On a single engine information center it is located on the left side of the ana-
log gauge cluster. On a dual engine information center it is located in the dig-
ital display.
Indicator Lights
Indicator lights are located in the speedometer and tachometers and display
a selected function, a normal condition, or a system anomaly.
An indicator light may be accompanied by a scrolling message in the multi-
function display. See table below for usual indicator light information.
Continued on next page.
Indicator
Light
Display Area
Message Display Description
Single
Engine
Information
Center
Dual
Engine
Information
Center
Speedometer Left Side
Tachometer SKI MODE related mes- sages
When ON: SKI MODE is
engaged.
When blinking: SKI MODE is
selected but not engaged.
Speedometer Left Side
Tachometer CRUISE MODE related messages CRUISE mode engaged.
Speedometer Left Side
Tachometer
Engine or exhaust system overheating (H-TEMP).
Audible alarm will sound and limp-home mode will activate.
Speedometer Left Side
Tachometer Low/High battery voltage (12 V LOW/HI)
Speedometer Left Side
Tachometer
Maintenance required or
Service Vehicle Soon
(Fault)
Could be turned on by the mainte-
nance counter or by a non-emis-
sion related fault that is active or
has been in the system and not
completed three healing drive
cycles.

6
Indicator
Light
Display Area
Message Display Description
Single
Engine
information
center
Dual
Engine
information
center
Tachometer Right Side
Tachometer –Indicates engine speed
synchronization is requested to
ECM’s
Tachometer Right Side
Tachometer LOW FUEL Low fuel level,
approx. 25%
Tachometer Right Side
Tachometer Low Oil Pressure Engine is in a low oil pressure
condition.
Tachometer Right Side
Tachometer Check Engine
An emission related fault is active
or has been active in the system
and has not completed three heal-
ing drive cycles.
Refer to the Fault Code menu.
ECO Tachometer Right Side
Tachometer –Indicates engine is set to operate
in most efficient range.

7
Fuel Level
A bar gauge located on the top of the digital screen indicates the amount of
fuel.
When the fuel tank is full, 8 segments (bars) of the indicator are turned ON.
When two segments of fuel is indicated (approximately 25% fuel tank capac-
ity) the low fuel indicator light will turn ON. An audible warning (one long
beep) will be heard periodically when the low fuel indicator is ON.
4
6
11
53
-
03

8
Numerical Display
The numerical display provides indications based on the selection made
from the DISPLAY menu. The data shown is:
*Requires input from a GPS antenna.
When the information center is turned ON, the numerical display defaults to
the last function chosen by the operator.
The numerical display is also used to show Ramp speed when in the SKI
MODE and Target speed while in the CRUISE MODE.
Engine(s) Fuel Consumption - Instant
Clock*Engine(s) temperature
Fuel Consumption - Average*Boat speed
4
6
11
53
-
03

9
Multifunction Display
The multifunction display provides an indication of compass heading or
scrolling messages.
It also displays a menu for the selection of various functions which, permits
changing the numerical display indication, system modes of operation, set-
tings, and displaying system fault codes.
NOTE: The compass heading selection is only available if a GPS antenna is
connected to the information center.
WARNING
Do not configure the information center when the boat is underway. Configuring the
information center when the boat is underway can result in a loss of situational
awareness. A loss of situational awareness may result in death or serious injury to
the occupants and operator.
4
6
11
53
-
03

10
Depth Sounder Indicator
If the vessel is equipped with a depth sounder, the numerical display can be
selected to provide an indication of the water depth. The selection of water
depth is only available if a depth transducer is connected to the information
center.
NOTE: Under certain conditions, the digital screen may stop displaying. The
digital screen's ability to display the depth depends on the conditions of use.
To activate depth indication, refer to CHANGING NUMERICAL DISPLAY IN-
DICATION.
WARNING
Never use the depth sounder as a warning device to ride in shallow water.
4
6
11
53
-
03
Depth Sounder Indicator
Water depth displays here.

11
Hour Meter Display
The Hour Meter continuously displays engine time in hours (Hr).
4
6
11
53
-
03
Port Engine Starboard Engine

12
Compass
The compass heading selection is only available if a GPS antenna is con-
nected to the information center.
A GPS incorporated in the information center provides the indication in the
multifunction display.
The cardinal points, intermediate cardinal points, as well as the azimuth the
boat is traveling are displayed in the multifunction display by default when the
boat is moving.
For a compass indication to be displayed, the GPS must have a link with the
navigation satellites.
NOTE: The compass indication is only available above 5 km/h (3 MPH).
WARNING
Use the compass as a guide only, do not use for navigation purposes.
4
6
11
53
-
03
Compass Indicator
Compass heading displays here.

13
Engine Identification
This indication identifies which engine is associated with the information
from the numerical display.
P = Port Engine
S = Starboard Engine
This indication will not display on a single engine information center.
4
6
11
53
-
03
Engine identification displays here.

14
Selecting Functions
When operating at speed, the multifunction display normally provides an
indication of the compass direction and azimuth the boat is traveling (if the
embedded GPS antenna received the proper satellite signals).
To select the various functions, press the MODE button repeatedly until the
desired menu is visible. The menu options are:
Press the SET button to enter the selected option.
NOTE: The fault code function is available only when there is an active fault.
The settings function is available at idle or when the engine is OFF.
Boat functions are enabled through a CAN Configuration Key (CCK) Module
which is added into the CAN network.
CCK, P/N 461337, includes SKI, CRUISE, DOCKING & ECO modes.
CCK, P/N 461340, includes CRUISE & DOCKING modes.
DOCKING MODE DISPLAY
SKI MODE SETTINGS
CRUISE MODE FAULT CODES
(only available when faults are active)
ECO Mode

15
Changing The Clock
1. Press the MODE button repeatedly until SETTINGS is displayed.
2. Press the SET button to validate your choice. The hour and the message
CLOCK will be displayed.
3. Press the SET button again, the message CHANGE CLOCK will be dis-
played.
4
6
11
53
-
0
4
4
6
11
53
-
05
4
6
11
53
-
06

16
4. Use UP / DOWN switch to adjust the clock. Only the hour indication and
be changed.
5. Press MODE or SET button to save the clock setting and return to the main
display.
Changing Numerical Display Indication
To change the indication in the numerical display, press the MODE button
repeatedly until DISPLAY is visible in the multifunction display. Press SET to
select the Display menu.
Move the Up / Down switch until the preferred indication is visible in the mul-
tifunction display.
Press the SET button to select and save the preferred indication, or wait for
the display function to time out. The last indication visible will be automatical-
ly saved. The numerical display will then switch to the new indication with a
small abbreviation of the indication type to its right:
FT or M °F or °C
RPM Gal/h or L/h
MPH or km/h AM or PM
4
6
11
53
-
0
7
Display Menu Sequence:
• Depth (when available)
• RPM
• Speed
• Engine Temperature
• Instant Fuel Flow
• Average Fuel Flow
• Clock

17
For example, to display the SPEED information:
• Press the MODE button repeatedly until DISPLAY is displayed, then press
SET button once
• Lift up the UP and DOWN switch until SPEED is displayed
• Press the SET button to confirm and save the selection
Main Menu
Main menu selections:
ECO MOD
E
4
6
11
53
-11

18
Docking Mode
To activate the Docking Mode:
• Reduce throttle speed to idle
• Press the Mode button until Docking is displayed
• Press the Set button once, the following message will be displayed: “Hold
Set To Activate Or Mode To Exit”
• Press and hold the Set button until Docking reappears
To cancel Docking Mode
• Press and hold the Mode button
• Move the throttle/shifter handle to the NEUTRAL position
Docking mode selections:
4
6
11
53
-12