BT DECOR 110 User manual

To delete stored numbers
Lift the handset.
Press the STORE button. The call
indicator light will flash.
Press the memory location
number (0-9) or (M1, M2, M3)
under which you have stored the
number you wish to delete.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
Alternatively, any existing
number stored in the Quickdial
or One-Touch memories can be
overwritten by entering a new
number under the same memory
location. Simply follow the
instructions under the storing
numbers sections previously shown.
BT Accessories and
Replacement Items
For a full range of accessories and
replacement items for BT
products please call 0870 240 5522,
or visit:
Wall
mounting
1. Locate lugs and mount the
plinth provided into the holes
under the base unit as shown.
2. Swing the plinth down to clip
into the top hole.
3. Drill 2 holes, 25mm deep using
a 3mm drill, for the screws
provided, using the template.
Ensure that you do not drill into
any hidden wiring or pipes.
Insert the wall plugs provided
and then insert a screw into each
hole. Leave 2-3mm between the
head of the screw and the wall.
4. Position the product onto the
screws.
5. Drop down to secure.
R&TTE Directive
Hereby, Suncorp Technologies Ltd,
declares that this BT Decor 110
is in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.
The Declaration of Conformance
for the BT Decor 110 is published
on the website
http://www.suncorptech.com/bt
Note
You can mix manual and
memory dialling as required, for
example, you can dial the area
code 020 8304 from the memory
and then complete the number
manually.
Note
If any error occurs in the storing
mode you will hear three short
beeps, then the product will
return to talk mode.
If you unplug your BT Decor 110
the numbers stored in the
memory will be saved. However,
the last number redial memory
will be lost.
General information
uarantee
Your BT Decor 110 is guaranteed
for a period of 12 months from the
date of purchase.
Subject to the terms listed below
the guarantee will provide for the
repair of, or at BT’s or its agent’s
discretion the option to replace the
BT Decor 110, or any component
thereof, which is identified as
faulty or below standard, or fails as
a result of inferior workmanship
or materials. Products over 28 days
old from the date of purchase
may be replaced with a refurbished
or repaired product.
The conditions of this
guarantee are:
• The guarantee shall only apply
to defects that occur within the
12 month guarantee period.
• Proof of purchase is provided.
• The equipment is returned to
the point of purchase.
• This guarantee does not cover
any faults or defects caused by
accidents, misuse, fair wear
and tear, neglect, tampering
with the equipment, or any
attempt at adjustment or repair
other than by approved agents.
• This guarantee does not affect
your statutory rights.
Within the 12 month guarantee
period:
In the unlikely event of a defect
occurring, please return the
product, with the receipt, to the
place of purchase.
Outside of the 12 month
guarantee period:
If your product needs repair after
the guarantee period has ended,
the repair must meet the approval
requirements for connection to the
telephone network. We recommend
that you contact BT’s approved
repair agent, TecLogic on 01672
564444 or a local qualified repairer.
If you have to return your
BT Decor 110
Pack the unit securely, preferably
in the original packaging. All parts
must be returned. We cannot take
responsibility for goods damaged
in transit.
Technical information
How many telephones can you
have?
All items of telephone equipment
have a Ringer Equivalence
Number (REN), which is used to
calculate the number of items
which may be connected to any
one telephone line. Your
BT Decor 110 has a REN of 1.
A total REN of 4 is allowed, if the
total REN of 4 is exceeded, the
telephones may not ring. With
different telephone types there is
no guarantee of ringing, even
when the REN is less than 4.
Switchboard compatibility
This product is intended for use
within the UK for connection to
the public telephone network and
compatible switchboards, which
support tone dialling and time
break recall. If in doubt please
consult your service provider.
Offices worldwide
The telecommunications services described in
this publication are subject to availability and
may be modified from time to time. Services
and equipment are provided subject to British
Telecommunications plc’s respective standard
conditions of contract. Nothing in this publication
forms any part of any contract.
© British Telecommunications plc 2003.
Registered Office: 81 Newgate Street, London
EC1A 7AJ.
Registered in England No. 1800000.
BT Decor 110 Issue 2 (8/03) 1
Designed by the Art & Design Partnership
Limited.
Printed in China.
BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596 BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596 BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596
4
5
1
2
69mm
BT Decor 110
CORDED TELEPHONE
This product is intended
for connection to analogue public switched
telephone networks and private switchboards
in the United Kingdom.

Making and ending calls
To make a call
Lift the handset and wait for the
dial tone.
Dial the telephone number.
To end a call
Replace the handset.
To receive a call
When the telephone rings the call
indicator light will also flash to
indicate that there is an incoming
call. Simply pick up the handset.
To redial the last number
called
Lift the handset.
Press the REDIAL button.
The last number called is dialled.
A redial number can be no longer
than 32 digits.
Secrecy
When on a call you can talk to
someone in the same room,
without your caller hearing.
To switch secrecy on and off
During a call press and release the
SECRECY button.
The call indicator light will flash to
show that secrecy is on.
Your caller will be put on hold.
You can now talk to someone in
the room without your caller
hearing you.
Press and release the SECRECY
button again to return to your
caller.
To adjust the ringer volume
There are 3 volume settings to
choose from: HIGH, LOW or OFF.
The default setting is HIGH.
Lift the handset and press the
STORE button. The call indicator
light will flash.
Press the ✱button.
Press either, 1for HIGH, 2for
LOW or 3for OFF.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
(If the ringer is set to OFF, the call
indicator light will still flash to
indicate someone is calling you.)
To set the ringer pitch
The ringer pitch can be set to
High or Low. The default setting
is High.
Lift the handset and press the
STORE button. The call indicator
light will flash.
Press the
#
button.
Press either, 1for HIGH or 2for
LOW.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
123
456
789
0
BT Decor 110
Quickdial
Store
R
S
Redial
W
X
Y
Z
M
N
O
D
E
F
T
U
V
J
K
L
A
B
C
P
Q
R
S
G
H
I
S
e
c
r
e
c
y
One-Touch memories
You can store your three most
frequently used telephone numbers
in the One-Touch memories
(M1, M2 or M3). Please note that
the number can be no longer than
18 digits.
To store a One-Touch number
Lift the handset.
Press the STORE button. The call
indicator light will flash.
Press the memory location number,
(M1, M2, M3), under which you
want to store the number.
Enter the telephone number you
want to store including the area
code if applicable.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
To dial a One-Touch number
Lift the handset and wait for the
dial tone.
Press the memory location
number, (M1, M2, M3), under
which the number is stored.
The number is dialled
automatically.
To insert a pause in a memory
number
Sometimes you may need to enter
a pause when storing a number,
e.g. with an overseas number you
may need to enter a pause after
storing the international code.
Press the REDIAL button in the
place where you want to enter a
pause.
When you dial the number your
BT Decor 110 will automatically
insert the pause where you
stored it.
Quickdial memories
You can store a further 10 telephone
numbers in the Quickdial memories.
Please note that the numbers can
be no longer than 18 digits long.
To store a number in the
Quickdial memory
Lift the handset.
Press the STORE button.
The call indicator light will flash.
Press the memory location
number between 0and 9under
which you want to store the
number.
Enter the telephone number you
want to store including the area
code if applicable.
Press the STORE button.
You will hear a confirmation tone.
Replace the handset.
To dial a number in the
Quickdial memory
Lift the handset and wait for the
dial tone.
Press the QUICKDIAL button.
Press the memory location
number between 0and 9, under
which the number is stored.
The number is dialled automatically.
Note
Whilst storing a number in the
memory you can cancel the
operation by replacing the handset
on the cradle.
Setting up
Plan the location of your
BT Decor 110.
Situate your BT Decor 110 close
enough to a phone socket so that
the line cord will reach.
You can wall-mount your product,
see back page.
1. Plug your BT Decor 110
into the telephone socket.
Your BT Decor 110 is now ready
for use.
Using the telephone
At a glance
Quickdial button
Allows you to dial up to ten numbers
stored in the Quickdial memory at the
touch of two buttons.
One-Touch memory buttons
(M1, M2, M3)
Allows you to store and
automatically dial up to three
numbers at the touch of one
button.
Store button
Use to store numbers in the memory
and to change the ringer and pitch
volume.
Call indicator light
Flashes to indicate an incoming call.
Also flashes when storing numbers,
using secrecy or setting the ringer.
Redial/Pause button
Redials the last number called.
Also, press to enter a pause when
storing a number in the memory.
Secrecy button
Lets you talk to someone in the same
room without the person you are
calling hearing you.
Recall button
For use with a switchboard/PBX and
BT Calling Features. Please contact
your switchboard supplier for more
information. For more information on
BT’s Calling Features please call
Freefone 0800 800152
Handset hook
Keeps the handset in place when the
BT Decor 110 is wall mounted.
See back page for more information.
Revolve the handset catch on the
base unit. The handset will now be
able to rest on the hook when
wall-mounted.
Safety information
eneral
Simply clean your BT Decor 110 with a
damp (not wet) cloth, or an anti-static
wipe. Never use household polish as this
may damage the product. Never use a
dry cloth as this may cause static shock.
Do not open the BT Decor 110. This
could expose you to high voltages or
other risks.
Environmental
Do not expose to direct sunlight.
We recommend that you do not place the
product on antique/veneered wood to
avoid damage.
Do not stand your product on carpets or
other surfaces which generate fibres, or
place it in locations preventing free flow
of air over its surfaces.
Do not submerge any part of your
product in water and do not use it in damp
or humid conditions, such as in bathrooms.
Do not expose your product to fire,
explosive or other hazardous conditions.
Note
There is a quickdial memory
label on your telephone. Lift the
plastic plate up and you can
write on the label to keep a
record of which memory location
number you have used for each
telephone number.
BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596 BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596 BT Decor 110 ~ Issue 2 ~ 1st Edition ~ 27th Au ust ’03 ~ 5596
Note
During all storing operations the
call indicator light will flash.