Bticino FC80GT User manual

Installation Manual
www.bticino.com
Btdin with Netatmo
RA00180AC-12/21-PC

Btdin with Netatmo
Installation Manual

3
Contents
Btdin with Netatmo
Installation Manual
General features 4
Install Btdin with Netatmo 5
Associate the wired devices 8
Add a wired device 11
Reset to the factory settings 13
Use the App 15
Compatibility with civil series 16
Add a wireless scenario control 18
Associate a wireless light control to one or more modular wired devices 22
Dissociate a wireless control from the wired devices 28

4
Btdin with Netatmo
Installation Manual
General features
The Gateway allows you to create your Smart electric system by associating together all the wired
devices of the Btdin with Netatmo range.
The Gateway connects to your home router through the Wi-Fi connection (2.4GHz only), to allow
the local or remote control of lights and socket using the smartphone (“Home + Control” App) or
voice controls (using a voice assistant).
In order to optimize signal reception, it is recommended that the Gateway is installed close to the
router.
General considerations for the devices and functions shown in this manual.
- The Living Now with Netatmo series was used as an example for the graphic representation of the civil
series devices.
- The functions described are valid for all the “with Netatmo” civil series. It is possible to add other
functions (e.g. heating management), through integration with other devices of the “with Netatmo”
offer (e.g. Smarther with Netatmo).
- The products and features shown may not be available in all markets.
Check with your supplier or installer about their availability.
DIN Smart
gateway
DIN Smart
contactor Relè smart DIN smart relay for light
Connected
DIN load
management
module
COIL
F20T60A
FC80GCS


COIL
FC80GT FC80CC FC80RC F20T60A FC80GCS

54
Btdin with Netatmo
Installation Manual
Install Btdin with Netatmo
Check that the system is not powered.
It is now possible to connect all your system devices as per the following diagrams.
OFF
1. Disconnect the voltage from the general switch.
1
L
N
Relè smart FC80RC
Equipped with contacts
for control with
remote buttons
Contactor smart
FC80CC suitable for
controlling
single-phase
Smart DIN
gateway FC80GT
Relè smart FC80RC
equipped with contacts
for control with
remote buttons
Smart DIN FC80CC
contactor suitable
for controlling
single-phase
Measurement
toroid
Connected DIN
load management
module F80GCS
L
N
DIN smart
relay for light
F20T60A
Box
Measurement
toroid

6
Btdin with Netatmo
Installation Manual
Check that the LEDs of all the devices turn on red steady (with the exception of the gateway LED,
which remains off).
ON
2. Reconnect the power using the general switch.
2
COIL
F20T60A
FC80GCS


COIL

76
Btdin with Netatmo
Installation Manual
It is now possible to associate all the devices and take advantage of the connected functions of
your system.
Note: smart contactors will be powered by default.
After installing the smart electric system, it will be possible to control lights and loads without
further set up needed.

8
Btdin with Netatmo
Installation Manual
Associate the wired devices
1. Disconnect the voltage from the general switch.
2. Wait for 1 minute.
OFF
1
2
ON
3
4
Perform the pairing procedure shown below within 15 minutes of powering up the system.
Otherwise repeat the operation from the beginning.
3. Reconnect the power using the general switch.
4. Wait 1 minute for correct system startup.
COIL
F20T60A
FC80GCS


COIL

98
Btdin with Netatmo
Installation Manual
1. Start the association:
press the reset key of the Gateway until the LED turns green.
Note: the LEDs may take up to 15 minutes to turn from red to green.
After this time, the procedure will end automatically.
Check that the LEDs of all the devices turn green steady.
COIL
F20T60A
FC80GT Gateway
1
FC80GCS


COIL

10
Btdin with Netatmo
Installation Manual
2. End the association:
press and release the reset key of the Gateway, the LED switches off.
Check that the LEDs of all the devices immediately turn off: the wired devices are now associated
with each other.
Note: if the LEDs of any devices stay red, disconnect the power from the system, reconnect it, wait a
minute and then repeat the procedure from item 1.
FC80GT Gateway
2
COIL
F20T60A
FC80GCS


COIL

1110
Btdin with Netatmo
Installation Manual
Note: if the association with the Home + Control App has already been completed, follow the
instructions of the “Add a product to this home” menu in the App, or:
Add a wired device
OFF
1. Disconnect the voltage from the general switch.
2. Install the new wired device.
1
ON
3. Reconnect the power supply using the general switch and wait 1 minute for correct system
startup.
3
2

12
Btdin with Netatmo
Installation Manual
Note: if completed using the App, this procedure will suggest exactly the same sequence of actions
described here.
Check that the LEDs of all the devices are off, with the exception of the device to add, which must
have a steady red LED.
4. Complete the association of the new device as shown in “Associate wired devices” (point 1).
COIL
F20T60A
FC80GCS


COIL

1312
Btdin with Netatmo
Installation Manual
Reset to the factory settings
Procedure for Gateway DIN smart FC80GT
Procedure for Contactor smart FC80CC and Relay smart FC80RC
This procedure completely disconnects the device and returns it to the factory settings.
All data will be lost.
1. Press and hold down the reset pushbutton, the LED turns orange then switches off and at last
turns orange again.
Now release.
The LED switches off and the reset has been done.
1. Press and hold down the reset pushbutton.
The LED turns red.
Now release the pushbutton.
The LED turns red steady. The reset has been done.
Warning: a short accidental pressure of the reset pushbutton, starts the association (green LEDs are
ON). Press quickly the reset pushbutton of the FC80GT gateway to end it.
Total reset
1

14
Btdin with Netatmo
Installation Manual
Procedure for Gateway DIN smart FC80GT
1. press and hold down the reset pushbutton, the LED turns orange.
Now release.
The LED switches off and the reset has been done.
Reset HomeKit and the Wi-Fi network
1

1514
Btdin with Netatmo
Installation Manual
After completing the association of all the wired devices to the gateway it will immediately be
possible to:
– control lights and sockets.
Download the “Home + Control” App and configure it so that all the other functions of the Smart
electric system are available:
• scenario customisation
• remote control with Smartphone
• voice control using your favourite voice assistant
• receive notifications in case of overload or fault in the system
• check electric consumptions.
for more info visit
www.homesystems-legrandgroup.com
To download the Home + Control App
Use the App

16
Btdin with Netatmo
Installation Manual
Compatibility with civil series
You can associate to your Smart electric system other civil series wired and wireless devices. This
section shows as examples devices of the Living Now with Netatmo range, although the same
functions may also be combined with other BTicino with Netatmo ranges.
This integration allows to extend the functionality of your Smart DIN system. In addition, you will be
able to:
- activate scenarios using radio controls
- activate light relays using radio controls
- activate smart contactors using radio controls
- manage shutters.
Devices for civil series and junction box
Gateway
Modular
gateway
Gateway + type F
socket
Gateway + type E
socket
Sockets
Wired module
for modular
socket
Type F
connected
socket
Type E
connected
socket
Type F Plug&play
connected
socket
Type E Plug&play
connected
socket
Lights
ZLD15
K4411CM2
RF
L
NN
µ
1.3A max
0.4A max
ON
OFF
100-240V
50Hz/60Hz
Made in
China
ZLS26
Wired two-way
switch
Wired
dimmer/switch
2-module wired
dimmer/switch
Wired light
relay
Shutters
ZLSH06
K4027CM2
Wired shutter
control
2-module wired
shutter control
Wired actuator
for shutter

1716
Btdin with Netatmo
Installation Manual
Wireless controls
Flush mounted
wireless light control
Flush mounted
wireless shutter
control
Flush mounted
IN&OUT scenario
control
Flush mounted
wireless Night&Day
scenario control
1
2
3
4
Wall mounted
wireless light
control
Wall mounted
wireless double light
control
Wall mounted
wireless 4-scenario
control
Wall mounted
wireless In&Out
scenario control
1 2
Wireless module
for mechanical
switch
Wall mounted
wireless shutter
control
Wireless
movement
detector
Wall mounted
wireless Night&Day
scenario control

18
Btdin with Netatmo
Installation Manual
Add a wireless scenario control
1. Start the association:
press the reset key of the Gateway until the LED turns green.
Check that the LEDs of all the devices immediately turn green steady (with the exception of the
wireless LEDs, which will be off).
FC80GT Gateway
1
COIL
F20T60A
FC80GCS


COIL

1918
Btdin with Netatmo
Installation Manual
2. Remove the tab from the control
3. Press and release one of the control keys: the LED flashes green; release it and wait for the LED
to turn off.
* If the procedure fails, remove and reinsert the battery, then, repeat the operation.
Wireless In&Out scenario control
2
Warning: if cover and plate are not fitted, do not press the wireless control keys.
3
*KO

20
Btdin with Netatmo
Installation Manual
Check that the LEDs of all the devices immediately turn off: the wired devices are now associated
with each other.
4. End the association:
press and release the reset key of the Gateway, the LED switches off.
FC80GT Gateway
4
COIL
F20T60A
FC80GCS


COIL