Budgit LOAD LIFTER 622 Series User manual

Operating, Maintenance &
Parts Manual
Series 622
Hand Chain Hoist
Rated Loads:
Follow all instructions and warnings for
inspecting, maintaining and operating this hoist.
The use of any hoist presents some risk of personal injury or property
damage. That risk is greatly increased if proper instructions and
warnings are not followed. Before using this hoist, each operator
should become thoroughly familiar with all warnings, instructions and
recommendations in this manual.
Retain this manual for future reference and use.
Forward this manual to operator.
Failure to operate equipment as directed in manual
may cause injury
.
Before using the hoist, fill in the information below:
Model No.
Serial No.
Purchase Date
Manual No. 622Y-1
Tons
1/2
1
2
3
5
10
Kgs
500
1000
2000
3000
5000
10,000
LOAD LIFTER
®
inspecting, maintaining and operating this hoist.
ollow all instructions and warnings for
inspecting, maintaining and operating this hoist.
10
Kgs
500
1000
Rated Loads:
Kgs
Series 622
Series 622
1
2
Tons
1/2
Series 622
Rated Loads:
Series 622
Rated Loads:
Series 622
LOAD LIFTER
LOAD LIFTER
n
d
C
a
n
a
d
C
n
d
n
d
d
d
n
n
n
n
n
n
n
n
n
n
d
d
n
n
d
n
n
d
n
d
n
n
n
n
n
d
d
d
d
C

SAFETY PRECAUTIONS
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of the * American Society of Mechanical Engineers Code B30.16
“Overhead Hoist” and the Occupation Safety and Health Act.
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
be responsible for applications other than those for which Budigit equipment is recommended.
Consult Budgit for any usage of Series 622 Hoists that do not involve raising of the load on the lower hook, or usage of
Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accident that could result in
injury and/or property damage.
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A.
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS.
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE
EQUIPMENT BEFORE ATTEMPTING TO OPERATE YOUR SERIES 622 HOIST.
DO’S AND DO NOT’S
Safe Operation of Hoists
The following are Do’s and Do Not’s for safe operation of
overhead hoists. Taking precedence over any specific rule
listed here, however, is the most important rule of all, USE
COMMON SENSE. A few minutes spent reading these
rules can make an operator aware of dangerous practices
to avoid and precautions to take for his own safety and the
safety of others. Frequent examinations and periodic in-
spections of the equipment as well as a conscientious ob-
servance of safety rules may save lives as well as time and
money.
1. DO read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
2. DO be familiar with hoist operating controls,
procedures and warnings.
3. DO make sure the hoist suspension hook is
securely attached to a suitable support.
4. DO maintain firm footing or be otherwise secured
when operating hoist.
5. DO make sure that load slings or other approved
single attachments are properly sized
and seated in the hook saddle.
6. DO make sure that the hook latch, if used, is
closed and not supporting any part of the load.
7. DO make sure that load is free to move and will
clear all obstructions.
8. DO take up slack chain carefully, check load
balance, lift a few inches (centimeters) and
check load holding action before continuing.
9. DO make sure that all persons stay clear of the
suspended load.
10. DO avoid swinging of load or load hook.
11. DO protect load chain from weld spatter or
other damaging contaminants.
12. DO promptly report any malfunction, unusual
performance, or damage of the hoist.
13. DO inspect hoist regularly, replace damaged or
worn parts, and keep appropriate records of
maintenance.
14. DO use Budgit parts when repairing a hoist.
15. DO use hook latches wherever possible.
16. DO apply lubricant to the load chain as recommended
in this manual.
17. DO replace damaged or malfunctioning hook
latch.
18. DO NOT lift more than rated load.
19. DO NOT use damaged hoist or hoist that is not
working correctly.
20. DO NOT use the hoist with twisted, kinked,
damaged or worn chain.
21. DO NOT lift a load unless chain is properly
seated in chain wheel(s).
22. DO NOT use load chain as a sling or wrap
chain around the load.
23. DO NOT lift a load if any binding prevents equal
loading on all supporting chains.
24. DO NOT apply the load to the tip of the hook.
25. DO NOT operate unless load is centered under
hoist.
26. DO NOT operate hoist with other than manual
power.
27. DO NOT permit more than one operator to pull
on a single hand chain at one time.
28. DO NOT allow your attention to be diverted
from operating the hoist.
29. DO NOT operate the hoist beyond limits of load
chain travel.
30. DO NOT use hoist to lift, support or transport
people.
31. DO NOT lift loads over people.
32. DO NOT leave a suspended load unattended
unless specific precautions have been taken.
33. DO NOT allow sharp contact between two
hoists or between hoist and obstructions.
34. DO NOT allow the chain or hook to be used as
a ground for welding.
35. DO NOT allow the chain or hook to be touched
by a live welding electrode.
36. DO NOT remove or obscure the warnings on
the hoist.
37. DO NOT adjust or repair a hoist unless qualified
to perform hoist maintenance.
38. DO NOT attempt to lengthen the load chain or
repair damaged load chain.
WARNING - To Avoid Injury:
2
BUDGIT HOIST PARTS AND SERVICES ARE AVAILABLE
IN THE UNITED STATES AND IN CANADA
As a Budgit Hoist and Trolley user you are assured of reliable repair and parts services through a network of Master Parts
Depots and Service Centers that are strategically located in the United States and Canada. These facilities have been se-
lected on the basis of their demonstrated ability to handle all parts and repair requirements promptly and efficiently. To
quickly obtain the name of the Master Parts Depot or Service Center located nearest you, call [phone]. Fax: (716)
689-5644.
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
make sure the hoist suspension hook is
- To Avoid Injury:
21.
22.
20.
DO NOT
damaged or worn chain.
DO NOT
damaged or worn chain.
DO NOT
damaged or worn chain.
DO NOT
DO NOT
working correctly.
DO NOT
working correctly.
DO NOT
working correctly.
in this manual.
replace damaged or malfunctioning hook
lift more than rated load.
use damaged hoist or hoist that is not
use Budgit parts when repairing a hoist.
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
apply lubricant to the load chain as recommended
use hook latches wherever possible.
apply lubricant to the load chain as recommended
use hook latches wherever possible.
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A
worn parts, and keep appropriate records of
Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accid
ent that could result in
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A
ent that could result in
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
servance of safety rules may save lives as well as time and
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
WARNING
- To Avoid Injury:
to avoid and precautions to take for his own safety and the
safety of others. Frequent examinations and periodic in-
to avoid and precautions to take for his own safety and the
safety of others. Frequent examinations and periodic in-
to avoid and precautions to take for his own safety and the
spections of the equipment as well as a conscientious ob-
safety of others. Frequent examinations and periodic in-
spections of the equipment as well as a conscientious ob-
safety of others. Frequent examinations and periodic in-
servance of safety rules may save lives as well as time and
spections of the equipment as well as a conscientious ob-
servance of safety rules may save lives as well as time and
spections of the equipment as well as a conscientious ob-
- To Avoid Injury:
overhead hoists. Taking precedence over any specific rule
listed here, however, is the most important rule of all,
overhead hoists. Taking precedence over any specific rule
listed here, however, is the most important rule of all,
overhead hoists. Taking precedence over any specific rule
. A few minutes spent reading these
listed here, however, is the most important rule of all,
. A few minutes spent reading these
listed here, however, is the most important rule of all,
rules can make an operator aware of dangerous practices
. A few minutes spent reading these
rules can make an operator aware of dangerous practices
. A few minutes spent reading these
to avoid and precautions to take for his own safety and the
rules can make an operator aware of dangerous practices
to avoid and precautions to take for his own safety and the
rules can make an operator aware of dangerous practices
safety of others. Frequent examinations and periodic in-
to avoid and precautions to take for his own safety and the
safety of others. Frequent examinations and periodic in-
to avoid and precautions to take for his own safety and the
spections of the equipment as well as a conscientious ob-
safety of others. Frequent examinations and periodic in-
spections of the equipment as well as a conscientious ob-
safety of others. Frequent examinations and periodic in-
servance of safety rules may save lives as well as time and
spections of the equipment as well as a conscientious ob-
servance of safety rules may save lives as well as time and
spections of the equipment as well as a conscientious ob-
for safe operation of
overhead hoists. Taking precedence over any specific rule
for safe operation of
overhead hoists. Taking precedence over any specific rule
for safe operation of
listed here, however, is the most important rule of all,
overhead hoists. Taking precedence over any specific rule
listed here, however, is the most important rule of all,
overhead hoists. Taking precedence over any specific rule
USE
overhead hoists. Taking precedence over any specific rule
USE
overhead hoists. Taking precedence over any specific rule
. A few minutes spent reading these
17.
18.
19.
15.
16.
in this manual.
17.
DO
latch.
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A
worn parts, and keep appropriate records of
maintenance.
worn parts, and keep appropriate records of
maintenance.
worn parts, and keep appropriate records of
14.
DO
use Budgit parts when repairing a hoist.
15.
DO
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
DO
apply lubricant to the load chain as recommended
use hook latches wherever possible.
apply lubricant to the load chain as recommended
use hook latches wherever possible.
in this manual.
apply lubricant to the load chain as recommended
in this manual.
apply lubricant to the load chain as recommended
Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accid
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A
worn parts, and keep appropriate records of
maintenance.
worn parts, and keep appropriate records of
maintenance.
worn parts, and keep appropriate records of
use Budgit parts when repairing a hoist.
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
use hook latches wherever possible.
use Budgit parts when repairing a hoist.
Consult Budgit for any usage of Series 622 Hoists that do not involve raising of the load on the lower hook, or usage of
Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accid
* Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE
EQUIPMENT BEFORE ATTEMPTING TO OPERATE YOUR SERIES 622 HOIST.
Consult Budgit for any usage of Series 622 Hoists that do not involve raising of the load on the lower hook, or usage of
Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accid
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS.
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
be responsible for applications other than those for which Budigit equipment is recommended.
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
be responsible for applications other than those for which Budigit equipment is recommended.
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS.
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED WITH THE
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of the * American Society of Mechanical Engineers Code B30.16
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of the * American Society of Mechanical Engineers Code B30.16
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Budgit industrial hoists. We recommend the use of equipment that meets state and national safety codes. Budgit cannot
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of the * American Society of Mechanical Engineers Code B30.16
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
complies with our interpretation of applicable sections of the * American Society of Mechanical Engineers Code B30.16
Each Series 622 Hand Hoist is built in accordance with the specifications contained herein and at the time of manufacture
The safety laws for elevators and for dumbwaiters may specify construction details that are not necessarily incorporated in
quickly obtain the name of the Master Parts Depot or Service Center located nearest you, call [phone]. Fax: (716)
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
DO
Overhead Hoists and this manual thoroughly.
DO
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly. be familiar with hoist operating controls, Overhead Hoists and this manual thoroughly.
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
3.
DO
procedures and warnings.
DO
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
4.
DO
securely attached to a suitable support.
DO
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
5.
DO
when operating hoist.
DO
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
6.
DO
closed and not supporting any part of the load.
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
DO
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
7.
DO
closed and not supporting any part of the load.
DO
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
clear all obstructions.
DO
take up slack chain carefully, check load
balance, lift a few inches (centimeters) and
take up slack chain carefully, check load
balance, lift a few inches (centimeters) and
take up slack chain carefully, check load
check load holding action before continuing.
balance, lift a few inches (centimeters) and
check load holding action before continuing.
balance, lift a few inches (centimeters) and
DO
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
2.
DO
Overhead Hoists and this manual thoroughly.
DO
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
3.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
6.
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
7.
make sure that load is free to move and will
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
clear all obstructions.
DO
take up slack chain carefully, check load
balance, lift a few inches (centimeters) and
take up slack chain carefully, check load
balance, lift a few inches (centimeters) and
take up slack chain carefully, check load
check load holding action before continuing.
balance, lift a few inches (centimeters) and
check load holding action before continuing.
balance, lift a few inches (centimeters) and
make sure that all persons stay clear of the
check load holding action before continuing.
make sure that all persons stay clear of the
check load holding action before continuing.
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
clear all obstructions.
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
make sure that load is free to move and will
closed and not supporting any part of the load.
take up slack chain carefully, check load
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
DO
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
DO
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
DO
make sure that the hook latch, if used, is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
DO
make sure that the hook latch, if used, is
DO
make sure that the hook latch, if used, is
closed and not supporting any part of the load.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
make sure that the hook latch, if used, is
securely attached to a suitable support.
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
and seated in the hook saddle.
securely attached to a suitable support.
securely attached to a suitable support.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
DO
make sure that load slings or other approved
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
maintain firm footing or be otherwise secured
securely attached to a suitable support.
maintain firm footing or be otherwise secured
securely attached to a suitable support.
when operating hoist.
maintain firm footing or be otherwise secured
when operating hoist.
maintain firm footing or be otherwise secured
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
single attachments are properly sized
make sure that load slings or other approved
single attachments are properly sized
make sure that load slings or other approved
and seated in the hook saddle.
single attachments are properly sized
and seated in the hook saddle.
single attachments are properly sized
DO
5.
DO
single attachments are properly sized
single attachments are properly sized
single attachments are properly sized
single attachments are properly sized
single attachments are properly sized
DO
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
when operating hoist.
make sure that load slings or other approved
when operating hoist.
make sure that load slings or other approved
when operating hoist.
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
Overhead Hoists and this manual thoroughly.
read ASME B30.16 Safety Standard for
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
procedures and warnings.
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
be familiar with hoist operating controls,
Overhead Hoists and this manual thoroughly.
procedures and warnings.
be familiar with hoist operating controls,
procedures and warnings.
be familiar with hoist operating controls,
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
procedures and warnings.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.
make sure the hoist suspension hook is
securely attached to a suitable support.

GENERAL INFORMATION
This manual contains important information to help you properly
install, operate and maintain your Series 622 Hoist for maximum
performance, economy and safety.
Please study its contents thoroughly before putting your hoist into
operation. By practicing correct operating procedures and by car-
rying out the recommended preventive maintenance suggestions,
you will be assured of long, dependable and safe service.
After you have completely familiarized yourself with the contents
of this manual, we recommend that you carefully file it for future
reference.
The information herein is directed to the proper use, care and
maintenance of the Series 622 Hoist and does not comprise a
handbook on the broad subject of rigging.
Rigging can be defined as the process of lifting and moving heavy
loads using hoists and other mechanical equipment. Skill ac-
quired through specialized experience and study is essential to
safe rigging operations. For rigging information, we recommend
consulting a standard textbook on the subject.
BUDGIT REPAIR/REPLACEMENT POLICY
All Budgit (Tugit) Series 622 Hoists are inspected and perform-
ance tested prior to shipment. If any properly maintained hoist
develops a performance problem, within one year of shipment,
due to a material or workmanship defect, as verified by Budgit, re-
pair or replacement of the unit will be made to the original pur-
chaser without charge. This repair/replacement policy applies
only to Series 622 Hoists installed, maintained and operated as
outlined in this manual, and specifically excludes hoists subject to
normal wear, abuse, improper installation, improper or inadequate
maintenance, hostile environmental effects and unauthorized re-
pairs/modifications.
We reserve the right to change materials or design if, in our opin-
ion, such changes will improve our product. Abuse, repair by an
unauthorized person, or use of non-BUDGIT replacement parts
voids the guarantee and could lead to dangerous operation. For
full Terms of Sale, see Sales Order Acknowledge-ment. Also,
refer to the back cover for Limitations of Warranties, Remedies
and Damages, and Indemnification and Safe Operation.
UNPACKING
After opening the carton, the hoist should be carefully inspected
for damage which may have occurred during shipment or han-
dling. Check the hoist frame for dents or cracks and inspect the
load chain for nicks and gouges. If shipping damage has oc-
curred, refer to the packing list envelope on the carton for claim
procedure.
GENERAL INFORMATION
After mounting and before placing in service, check the
hoist for proper operation. Before operating the 3, 5, and
10 ton units, make sure that all strands of chain are straight
and have no twists (due to capsized hook). If the chain is
twisted, reverse capsize. To operate the hoist, pull on the
hand chain as indicated below.
Loose End
Pin
Upper Hook
Hoist Frame
Load Chain
Hand Chain
Loose End
of Chain
Hook Latch
Lower Hook
To Raise Hook
Pull On This
Part of
Hand Chain
To Lower
Hook
Pull On This
Part of
Hand Chain
Operate the hoist with no load and then a light load of approxi-
mately 50 pounds (23 Kg.) times the number of load supporting
chains to make sure it operates properly and the brake holds the
load when the hand chain is released; then operate with a rated
load as shown on the capacity plate.
SAFETY PROCEDURES
1. The hoist must always be rigged to lift in a straight line from
hook to hook. The hoist must always be free to swivel on the
upper hook. Under no condition should the hoist frame be al-
lowed to bear on any support when in use as this would cause
bending of the hook or frame and damage the unit.
2. When preparing to lift or move a load, be sure that the at-
tachments to both hooks are firmly seated in the saddles of the
hooks. Avoid off center loading of any kind especially loading
on the tip of the hook. Also observe that the chain hangs
straight (without twist) from hoist to lower hook.
3. When lifting, raise the load only enough to clear the floor or
support, and check to be sure brake will hold load and that at-
tachments to the load are firmly seated. Continue the lift only
after you are assured the load is free of all obstructions.
4.Do not load beyond the rated capacity of the hoist. Rated
capacity can be:
Since these hand chain pulls can easily be applied by one per-
son, under no circumstances should more than one person op-
erate the hoist hand chain. Overloading can cause immediate
failure of some load carrying parts or result in damage causing
future failure at less than rated capacity. When in doubt, use
the next larger capacity Budgit hoist.
3
WARNING
Operating the 3, 5, and 10 ton hoists in the lifting direction with
the hook block in contact with the frame and/or hoist hanger
may break the chain and allow the load to drop.
TO AVOID INJURY:
Stop operating in the lifting direction when the hook block con-
tacts the hoist frame and/or hanger, as noted by sudden in-
crease in hand chain pull or tipping of the hook block.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
Hoist
Rated Load
tons (kg.)
Hand Chain Pull
to Lift Rated Load
lbs (kg.)
1/2 (500) 53 (25)
1 (1000) 77 (35)
2 (2000) 82 (37)
3 (3000) 65 (30)
5 (5000) 105 (48)
10 (10000) 109 (50)
curred, refer to the packing list envelope on the carton for claim
for damage which may have occurred during shipment or han-
dling. Check the hoist frame for dents or cracks and inspect the
load chain for nicks and gouges. If shipping damage has oc-
curred, refer to the packing list envelope on the carton for claim
After opening the carton, the hoist should be carefully inspected
for damage which may have occurred during shipment or han-
dling. Check the hoist frame for dents or cracks and inspect the
lowed to bear on any support when in use as this would cause
bending of the hook or frame and damage the unit.
1. The hoist must always be rigged to lift in a straight line from
hook to hook. The hoist must always be free to swivel on the
upper hook. Under no condition should the hoist frame be al-
lowed to bear on any support when in use as this would cause
SAFETY PROCEDURES
1. The hoist must always be rigged to lift in a straight line from
hook to hook. The hoist must always be free to swivel on the
tacts the hoist frame and/or hanger, as noted by sudden in-
crease in hand chain pull or tipping of the hook block.
the hook block in contact with the frame and/or hoist hanger
may break the chain and allow the load to drop.
may break the chain and allow the load to drop.
TO AVOID INJURY:
Stop operating in the lifting direction when the hook block con-
WARNING
Operating the 3, 5, and 10 ton hoists in the lifting direction with
the hook block in contact with the frame and/or hoist hanger
may break the chain and allow the load to drop.
WARNING
chains to make sure it operates properly and the brake holds the
load when the hand chain is released; then operate with a rated
Operate the hoist with no load and then a light load of approxi-
mately 50 pounds (23 Kg.) times the number of load supporting
chains to make sure it operates properly and the brake holds the
refer to the back cover for Limitations of Warranties, Remedies
and Damages, and Indemnification and Safe Operation.
After opening the carton, the hoist should be carefully inspected
for damage which may have occurred during shipment or han-
dling. Check the hoist frame for dents or cracks and inspect the
load chain for nicks and gouges. If shipping damage has oc-
curred, refer to the packing list envelope on the carton for claim
unauthorized person, or use of non-BUDGIT replacement parts
voids the guarantee and could lead to dangerous operation. For
full Terms of Sale, see Sales Order Acknowledge-ment. Also,
refer to the back cover for Limitations of Warranties, Remedies
and Damages, and Indemnification and Safe Operation.
After opening the carton, the hoist should be carefully inspected
We reserve the right to change materials or design if, in our opin-
ion, such changes will improve our product. Abuse, repair by an
unauthorized person, or use of non-BUDGIT replacement parts
voids the guarantee and could lead to dangerous operation. For
full Terms of Sale, see Sales Order Acknowledge-ment. Also,
refer to the back cover for Limitations of Warranties, Remedies
outlined in this manual, and specifically excludes hoists subject to
normal wear, abuse, improper installation, improper or inadequate
maintenance, hostile environmental effects and unauthorized re-
We reserve the right to change materials or design if, in our opin-
ion, such changes will improve our product. Abuse, repair by an
SAFETY PROCEDURES
outlined in this manual, and specifically excludes hoists subject to
normal wear, abuse, improper installation, improper or inadequate
tacts the hoist frame and/or hanger, as noted by sudden in-
crease in hand chain pull or tipping of the hook block.
the hook block in contact with the frame and/or hoist hanger
may break the chain and allow the load to drop.
Stop operating in the lifting direction when the hook block con-
tacts the hoist frame and/or hanger, as noted by sudden in-
Operating the 3, 5, and 10 ton hoists in the lifting direction with
the hook block in contact with the frame and/or hoist hanger
may break the chain and allow the load to drop.
Operate the hoist with no load and then a light load of approxi-
mately 50 pounds (23 Kg.) times the number of load supporting
chains to make sure it operates properly and the brake holds the
load when the hand chain is released; then operate with a rated
load as shown on the capacity plate.
WARNING
Operate the hoist with no load and then a light load of approxi-
mately 50 pounds (23 Kg.) times the number of load supporting
chains to make sure it operates properly and the brake holds the
load when the hand chain is released; then operate with a rated
load as shown on the capacity plate.
Operate the hoist with no load and then a light load of approxi-
mately 50 pounds (23 Kg.) times the number of load supporting
chains to make sure it operates properly and the brake holds the
Hand Chain
Hand Chain
Hand Chain
To Raise Hook
Pull On This
Hand Chain
load chain for nicks and gouges. If shipping damage has oc-
curred, refer to the packing list envelope on the carton for claim
procedure.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
Carefully check unit for external damage prior to installation.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
GENERAL INFORMATION
After mounting and before placing in service, check the
After mounting and before placing in service, check the
hoist for proper operation. Before operating the 3, 5, and
After mounting and before placing in service, check the
GENERAL INFORMATION
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
dling. Check the hoist frame for dents or cracks and inspect the
load chain for nicks and gouges. If shipping damage has oc-
curred, refer to the packing list envelope on the carton for claim
procedure.
GENERAL INFORMATION
After mounting and before placing in service, check the
hoist for proper operation. Before operating the 3, 5, and
After mounting and before placing in service, check the
hoist for proper operation. Before operating the 3, 5, and
After mounting and before placing in service, check the
WARNING
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
Carefully check unit for external damage prior to installation.
GENERAL INFORMATION
Carefully check unit for external damage prior to installation.
GENERAL INFORMATION
Carefully check unit for external damage prior to installation.
WARNING
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
to drop and that may result in personal injury and/or property
damage.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
Carefully check unit for external damage prior to installation.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
Carefully check unit for external damage prior to installation.
Carefully check unit for external damage prior to installation.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
TO AVOID INJURY:
Carefully check unit for external damage prior to installation.
to drop and that may result in personal injury and/or property
TO AVOID INJURY:
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
TO AVOID INJURY:
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
to drop and that may result in personal injury and/or property
damage.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
WARNING
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
damage.
Carefully check unit for external damage prior to installation.
damage.
damage.
damage.
damage.
Operating a unit with obvious external damage may cause load
to drop and that may result in personal injury and/or property
to drop and that may result in personal injury and/or property
to drop and that may result in personal injury and/or property
to drop and that may result in personal injury and/or property
curred, refer to the packing list envelope on the carton for claim

5. Do not wrap load chain around the load or bring the load in
contact with the hoist. Doing this will result in the loss of the
swivel effect of the hook which could mean twisted chain and a
jammed liftwheel. The chain could be damaged at the hook.
6. Stand clear of all loads and avoid moving a load over the
heads of other personnel. Warn personnel of your intention to
move a load in their area.
7. Do not leave the load in the air unattended.
8. Do not lower the hook to a point where the chain becomes
taut between the liftwheel and loose end pin.
9. Do not run the lower hook block into the hoist frame. Frame
and/or chain guide damage may result.
10. The hoist has been designed for manual operation only.
11. Do not use this or any other overhead materials handling
equipment for lifting persons.
12. Do not allow the load to bear against the hook latch. The
latch is to help maintain the hook in position while the chain is
slack before taking up slack chain.
13. Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
WARNING
Exceeding the rated capacity of the hoist may cause load to fall.
TO AVOID INJURY:
Do not exceed the hand chain pulls specified in 4 above.
GENERAL INFORMATION
INSPECTION
To maintain continuous and satisfactory operation, a regular in-
spection procedure must be initiated so that worn or damaged
parts can be replaced before they become unsafe. The intervals
of inspection must be determined by the individual application and
are based upon the type of service to which the hoist will be sub-
jected. The inspection of hoists is divided into two general classi-
fications designated as “frequent” and “periodic”.
Frequent Inspections:
These inspections are usually visual examinations by the operator
or other designated personnel. The frequent inspections are to
be performed daily or monthly and shall include the following
items:
a. Braking mechanisms for evidence of slippage — daily.
b. Load Chain for lubricant, wear, damaged links or foreign
material — daily. See below.
c. Hooks for damage, cracks, twists, latch engagement and
latch operation —monthly. See below.
Any deficiencies noted are to be corrected before the hoist is re-
turned to service.
Periodic Inspections:
These are visual inspections by an appointed person who makes
records of apparent external conditions to provide the basis for a
continuing evaluation. For normal service, the periodic inspec-
tions are to be performed yearly and for heavy service, the peri-
odic inspections are to be performed semi-annually.
Due to the construction of the hoist, it will be necessary to par-
tially disassemble the unit to perform the periodic inspections.
The periodic inspections are to include those items listed under
frequent inspections as well as the following:
a. Chain for excessive wear or stretch. See below.
b. Worn, cracked or distorted parts such as hook blocks, hoist
hanger, chain guide, stripper, loose end pin, shafts, gears,
hook collar and bearings.
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
and pockets of the liftwheel and handwheel.
d. Loose or missing bolts, nuts, pins or rivets.
e. Inspect brake components for worn, glazed or contaminated
friction discs and scoring of the handwheel hub, ratchet and
friction hub. Replace friction discs if the thickness is less than
0.044 in. (1.12 mm) on 1/2 & 1 ton units and 0.059 in. (1.50
mm) on 2, 3, 5 and 10 ton units
f. Corroded, stretched or broken pawl spring.
g. Free movement of the pawl on the pawl stud. Also, apply a
thin coat of lubricant to the pawl stud (see page 6) before re
assembling the unit.
h. Hooks — dye penetrant, magnetic particle or other suitable
crack-detecting inspections should be performed at least once
a year, if external conditions indicate there has been unusual
usage.
Any deficiencies noted are to be corrected before the hoist is re-
turned to service. Also, the external conditions may show the
need for more detailed inspection which, in turn, may require the
use of nondestructive-type testing.
Any parts that are deemed unserviceable are to be replaced with
new parts before the unit is returned to service. It is very impor-
tant that the unserviceable parts be destroyed to prevent possible
future use as a repair item and properly disposed of.
HOOK INSPECTION
Hooks damaged from chemicals, deformations or cracks or that
have more than a 10° twist from the plane of the unbent hook or
excessive opening or seat wear must be replaced.
Also, hooks that are opened and those that allow the latch to dis-
engage the tip, must be replaced.
Any hook that is twisted or has excessive throat opening indicates
abuse or over-loading of the unit. Other load-sustaining compo-
nents of the hoist should be inspected for damage.
The chart below should be used to determine when the hook
must be replaced. To measure throat opening, depress the latch
against the hook body as shown below.
4
WARNING
Power operation may result in structural damage or premature
wear that may cause a part to break and allow the load to fall.
TO AVOID INJURY:
Operate Series 622 Hoists using hand power only.
WARNING
Allowing the load to bear against the hook latch and/or hook tip
can result in loss of load.
TO AVOID INJURY:
Do not allow the load to bear against the hook latch and/or hook
tip. Apply load to hook bowl or saddle only.
13. Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
13. Never operate the hoist when flammable materials or vapors
Do not allow the load to bear against the hook latch and/or hook
Any deficiencies noted are to be corrected before the hoist is re-
turned to service. Also, the external conditions may show the
need for more detailed inspection which, in turn, may require the
a year, if external conditions indicate there has been unusual
usage.
assembling the unit.
h. Hooks — dye penetrant, magnetic particle or other suitable
crack-detecting inspections should be performed at least once
a year, if external conditions indicate there has been unusual
f. Corroded, stretched or broken pawl spring.
g. Free movement of the pawl on the pawl stud. Also, apply a
thin coat of lubricant to the pawl stud (see page 6) before re
assembling the unit.
h. Hooks — dye penetrant, magnetic particle or other suitable
e. Inspect brake components for worn, glazed or contaminated
friction discs and scoring of the handwheel hub, ratchet and
friction hub. Replace friction discs if the thickness is less than
0.044 in. (1.12 mm) on 1/2 & 1 ton units and 0.059 in. (1.50
mm) on 2, 3, 5 and 10 ton units
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
and pockets of the liftwheel and handwheel.
d. Loose or missing bolts, nuts, pins or rivets.
e. Inspect brake components for worn, glazed or contaminated
a. Chain for excessive wear or stretch. See below.
b. Worn, cracked or distorted parts such as hook blocks, hoist
hanger, chain guide, stripper, loose end pin, shafts, gears,
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
and pockets of the liftwheel and handwheel.
The periodic inspections are to include those items listed under
frequent inspections as well as the following:
a. Chain for excessive wear or stretch. See below.
b. Worn, cracked or distorted parts such as hook blocks, hoist
Due to the construction of the hoist, it will be necessary to par-
tially disassemble the unit to perform the periodic inspections.
The periodic inspections are to include those items listed under
records of apparent external conditions to provide the basis for a
continuing evaluation. For normal service, the periodic inspec-
tions are to be performed yearly and for heavy service, the peri-
Due to the construction of the hoist, it will be necessary to par-
These are visual inspections by an appointed person who makes
records of apparent external conditions to provide the basis for a
WARNING
Allowing the load to bear against the hook latch and/or hook tip
13. Never operate the hoist when flammable materials or vapors
TO AVOID INJURY:
Do not allow the load to bear against the hook latch and/or hook
tip. Apply load to hook bowl or saddle only.
WARNING
Allowing the load to bear against the hook latch and/or hook tip
12. Do not allow the load to bear against the hook latch. The
latch is to help maintain the hook in position while the chain is
11. Do not use this or any other overhead materials handling
12. Do not allow the load to bear against the hook latch. The
g. Free movement of the pawl on the pawl stud. Also, apply a
thin coat of lubricant to the pawl stud (see page 6) before re
assembling the unit.
h. Hooks — dye penetrant, magnetic particle or other suitable
mm) on 2, 3, 5 and 10 ton units
f. Corroded, stretched or broken pawl spring.
g. Free movement of the pawl on the pawl stud. Also, apply a
thin coat of lubricant to the pawl stud (see page 6) before re
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
and pockets of the liftwheel and handwheel.
d. Loose or missing bolts, nuts, pins or rivets.
e. Inspect brake components for worn, glazed or contaminated
friction discs and scoring of the handwheel hub, ratchet and
friction hub. Replace friction discs if the thickness is less than
0.044 in. (1.12 mm) on 1/2 & 1 ton units and 0.059 in. (1.50
mm) on 2, 3, 5 and 10 ton units
f. Corroded, stretched or broken pawl spring.
b. Worn, cracked or distorted parts such as hook blocks, hoist
hanger, chain guide, stripper, loose end pin, shafts, gears,
hook collar and bearings.
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
and pockets of the liftwheel and handwheel.
d. Loose or missing bolts, nuts, pins or rivets.
e. Inspect brake components for worn, glazed or contaminated
friction discs and scoring of the handwheel hub, ratchet and
friction hub. Replace friction discs if the thickness is less than
Due to the construction of the hoist, it will be necessary to par-
tially disassemble the unit to perform the periodic inspections.
The periodic inspections are to include those items listed under
frequent inspections as well as the following:
a. Chain for excessive wear or stretch. See below.
b. Worn, cracked or distorted parts such as hook blocks, hoist
hanger, chain guide, stripper, loose end pin, shafts, gears,
hook collar and bearings.
c. Inspect for wear on the tip of the pawl, teeth of the ratchet
tions are to be performed yearly and for heavy service, the peri-
odic inspections are to be performed semi-annually.
Due to the construction of the hoist, it will be necessary to par-
tially disassemble the unit to perform the periodic inspections.
The periodic inspections are to include those items listed under
frequent inspections as well as the following:
a. Chain for excessive wear or stretch. See below.
b. Worn, cracked or distorted parts such as hook blocks, hoist
hanger, chain guide, stripper, loose end pin, shafts, gears,
These are visual inspections by an appointed person who makes
records of apparent external conditions to provide the basis for a
continuing evaluation. For normal service, the periodic inspec-
tions are to be performed yearly and for heavy service, the peri-
odic inspections are to be performed semi-annually.
Due to the construction of the hoist, it will be necessary to par-
tially disassemble the unit to perform the periodic inspections.
The periodic inspections are to include those items listed under
Any deficiencies noted are to be corrected before the hoist is re-
These are visual inspections by an appointed person who makes
records of apparent external conditions to provide the basis for a
continuing evaluation. For normal service, the periodic inspec-
tions are to be performed yearly and for heavy service, the peri-
odic inspections are to be performed semi-annually.
c. Hooks for damage, cracks, twists, latch engagement and
Any deficiencies noted are to be corrected before the hoist is re-
13.Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14.STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
13.Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14.STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
GENERAL INFORMATION
tip. Apply load to hook bowl or saddle only.
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
INSPECTION
To maintain continuous and satisfactory operation, a regular in-
spection procedure must be initiated so that worn or damaged
parts can be replaced before they become unsafe. The intervals
13. Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
GENERAL INFORMATION
INSPECTION
To maintain continuous and satisfactory operation, a regular in-
spection procedure must be initiated so that worn or damaged
parts can be replaced before they become unsafe. The intervals
Do not allow the load to bear against the hook latch and/or hook
tip. Apply load to hook bowl or saddle only.
GENERAL INFORMATION
GENERAL INFORMATION
GENERAL INFORMATION
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
ished control.
GENERAL INFORMATION
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
GENERAL INFORMATION
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
14. STAY ALERT! Watch what you are doing and use common
GENERAL INFORMATION
GENERAL INFORMATION
GENERAL INFORMATION
GENERAL INFORMATION
under the influence of drugs, alcohol or medication causing dimin-
GENERAL INFORMATION
GENERAL INFORMATION
GENERAL INFORMATION
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
14. STAY ALERT! Watch what you are doing and use common
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
ished control.
GENERAL INFORMATION
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
GENERAL INFORMATION
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14. STAY ALERT! Watch what you are doing and use common
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
GENERAL INFORMATION
ished control.
sense. Do not use the hoist when you are tired, distracted or
under the influence of drugs, alcohol or medication causing dimin-
ished control.
ished control.
under the influence of drugs, alcohol or medication causing dimin-
ished control.
ished control.
13. Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
sparks that can cause a fire or explosion.
13. Never operate the hoist when flammable materials or vapors
are present. Sharp contact between metal parts can produce
sparks that can cause a fire or explosion.
14.STAY ALERT! Watch what you are doing and use common
14.STAY ALERT! Watch what you are doing and use common
14.STAY ALERT! Watch what you are doing and use common

Hoist
Rated Load
Tons (Kg.)
1
/ 2 (500)
1 (1000)
2 (2000)
3 (3000)
5 (5000)
10 (10000)
Replace Hook When
Opening Is Greater Than:
Inches mm
1.00 25.3
1.20 30.5
1.43 36.8
1.65 41.8
2.10 53.2
2.58 65.5
MEASURE
OPENING
HOOK THROAT OPENING
Also, check to make sure that the latch is not damaged or bent and
that it operates properly with sufficient spring pressure to keep the
latch tightly against the tip of the hook and allow the latch to spring
back to the tip when released. If the latch does not operate prop-
erly, it should be replaced.
LOAD CHAIN
Cleaning and Inspection
First clean the load chain with a non-acid or non-caustic type sol-
vent then slack the chain and make a link-by-link inspection for
nicks, gouges, twisted links and excessive wear or stretching. Worn
chain should be gaged throughout its entire length and replaced if
beyond serviceable limits.
To determine if load chain should be continued in service, check
gage lengths as indicated in figure below. Chain worn beyond
length indicated, nicked, gouged or twisted should be replaced be-
fore returning hoist to service. Chain should be clean, free of twists
and pulled taut before measuring. In cases where the wear is local-
ized and not beyond serviceable limits, it is sometimes possible to
reverse the load chain, end for end, and allow a new section to take
the wear. Proper installation of the load chain is covered in section
on Reeving Load Chain (page 7).
Note that worn chain can be an indication of worn hoist compo-
nents. For this reason, the hoist’s chain guide roller and liftwheel
should be examined for wear and replaced as necessary when re-
placing worn chain.
Also, load chains are specially heat treated and hardened and
should never be repaired.
HAND CHAIN
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be assembled to handwheel free from twists with
weld on vertical link facing inward towards handwheel and weld on
horizontal link facing towards the handwheel side plate.
Care must be taken to assure that there is no twist in the hand chain
loop.
LUBRICATION
Lubricate load chain with a light coat of Lubriplate Bar and Chain
Oil 10-R (Fiske Bros. Refining Co.) or equal lubricant. Be sure
the lubricant reaches the bearing surfaces between the links.
Remove excess oil from the chain.
The hoist normally requires no additional lubrication, except for peri-
odically lubricating the load chain as indicated above or when the
unit is disassembled for periodic inspections, cleaning or repairs.
The brake is designed to operate dry. Do not use any grease
or lubricant on the braking surfaces. When lubricating parts
adjacent to the brake, do not use an excessive amount of lubri-
cant which could seep onto the brake surfaces.
When the hoist is disassembled for periodic inspections, check the
pawl for free movement and apply a light coat of WD-40 (WD-40
Co.) lubricant to the pawl stud.
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
per hoist of Molykote BR-2-S (Dow Corning Corp.) grease or equiv-
alent—threads of handwheel; gears; liftwheel rollers; gear bearing
rollers; journals of chain guide and dead end pin; sheave wheel
rollers (3, 5 and 10 ton); hook ball bearings (3 and 5 ton); hook col-
lar journals (3 and 5 ton); dead end stud (3, 5 and 10 ton); bearing
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
pin (10 ton).
NOTE: To assure extra long life and top performance, be sure
to lubricate the various parts of the hoist using the lubricants
specified above. If desired, these lubricants may be purchased
from BUDGIT. Refer to pages 8 and 10 for information on or-
dering the lubricants.
DISASSEMBLY
Two points of caution to be observed in disassembly are:
1. Loose rollers and bearing balls are used in various locations in
the units. Care must be taken so as to not lose or misplace these
since they may drop from the unit as the various parts are disas-
sembled. The number of rollers or bearing balls used are:
2. The latch is secured to the hook (upper and lower) by a rivet.
To remove the latch, it is necessary to remove the head of the rivet
by grinding or drilling. For replacement of the latch, refer to para-
graph 4 of the Assembly Instructions.
ASSEMBLY
Consideration must be given to the following when assembling the
hoist:
1. Assemble the brake components as shown below. The ratchet
teeth must face as shown and engage the pawl. Do not lubricate
the brake surfaces. The brake operates dry. Assemble handwheel
to pinion shaft and turn handwheel to seat brake components. As-
semble the pinion shaft nut to the shaft until the nut bottoms. Then
back nut off at least one but not more than two flats. Insert cotter
pin and bend ends to secure same.
*Bearing Balls
Hoist Rated Load
tons (kg) Location Rollers Req’d
1 (1000)
2-10 (2000-10000)
1/2 (500)
1 (1000)
2-10 (2000-10000)
3-5 (3000-5000)
3 (3000)
5 (5000)
10 (10000)
Intermed. Gear
Intermed. Gear
Liftwheel
Liftwheel
Liftwheel
Sheave Wheel
Hook
Hook
Sheave Wheel
12 Each End
11 Each End
33 Each End
30 Each End
35 Each End
29
*15
*16
36
5
WARNING
Used motor oils contain unknown carcinogenic materials.
TO AVOID HEALTH PROBLEMS:
Never use used motor oils as a chain lubricant. Only use
Lubriplate Bar and Chain Oil 10-R as a lubricant for the load
chain.
Hand chain should be cleaned, inspected and gaged in the same
Also, load chains are specially heat treated and hardened and
nents. For this reason, the hoist’s chain guide roller and liftwheel
should be examined for wear and replaced as necessary when re-
since they may drop from the unit as the various parts are disas-
sembled. The number of rollers or bearing balls used are:
Hoist Rated Load
1. Loose rollers and bearing balls are used in various locations in
the units. Care must be taken so as to not lose or misplace these
since they may drop from the unit as the various parts are disas-
sembled. The number of rollers or bearing balls used are:
Two points of caution to be observed in disassembly are:
1. Loose rollers and bearing balls are used in various locations in
the units. Care must be taken so as to not lose or misplace these
dering the lubricants.
DISASSEMBLY
Two points of caution to be observed in disassembly are:
NOTE: To assure extra long life and top performance, be sure
to lubricate the various parts of the hoist using the lubricants
specified above. If desired, these lubricants may be purchased
from BUDGIT. Refer to pages 8 and 10 for information on or-
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
NOTE: To assure extra long life and top performance, be sure
alent—threads of handwheel; gears; liftwheel rollers; gear bearing
rollers; journals of chain guide and dead end pin; sheave wheel
rollers (3, 5 and 10 ton); hook ball bearings (3 and 5 ton); hook col-
lar journals (3 and 5 ton); dead end stud (3, 5 and 10 ton); bearing
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
per hoist of Molykote BR-2-S (Dow Corning Corp.) grease or equiv-
alent—threads of handwheel; gears; liftwheel rollers; gear bearing
rollers; journals of chain guide and dead end pin; sheave wheel
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
When the hoist is disassembled for periodic inspections, check the
pawl for free movement and apply a light coat of WD-40 (WD-40
adjacent to the brake, do not use an excessive amount of lubri-
the wear. Proper installation of the load chain is covered in section
Note that worn chain can be an indication of worn hoist compo-
nents. For this reason, the hoist’s chain guide roller and liftwheel
should be examined for wear and replaced as necessary when re-
Also, load chains are specially heat treated and hardened and
and pulled taut before measuring. In cases where the wear is local-
ized and not beyond serviceable limits, it is sometimes possible to
reverse the load chain, end for end, and allow a new section to take
the wear. Proper installation of the load chain is covered in section
Note that worn chain can be an indication of worn hoist compo-
nents. For this reason, the hoist’s chain guide roller and liftwheel
should be examined for wear and replaced as necessary when re-
To determine if load chain should be continued in service, check
gage lengths as indicated in figure below. Chain worn beyond
length indicated, nicked, gouged or twisted should be replaced be-
fore returning hoist to service. Chain should be clean, free of twists
and pulled taut before measuring. In cases where the wear is local-
ized and not beyond serviceable limits, it is sometimes possible to
reverse the load chain, end for end, and allow a new section to take
the wear. Proper installation of the load chain is covered in section
nicks, gouges, twisted links and excessive wear or stretching. Worn
chain should be gaged throughout its entire length and replaced if
To determine if load chain should be continued in service, check
gage lengths as indicated in figure below. Chain worn beyond
length indicated, nicked, gouged or twisted should be replaced be-
DISASSEMBLY
Two points of caution to be observed in disassembly are:
1. Loose rollers and bearing balls are used in various locations in
nicks, gouges, twisted links and excessive wear or stretching. Worn
specified above. If desired, these lubricants may be purchased
from BUDGIT. Refer to pages 8 and 10 for information on or-
dering the lubricants.
DISASSEMBLY
lar journals (3 and 5 ton); dead end stud (3, 5 and 10 ton); bearing
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
pin (10 ton).
NOTE: To assure extra long life and top performance, be sure
to lubricate the various parts of the hoist using the lubricants
specified above. If desired, these lubricants may be purchased
from BUDGIT. Refer to pages 8 and 10 for information on or-
dering the lubricants.
rollers; journals of chain guide and dead end pin; sheave wheel
rollers (3, 5 and 10 ton); hook ball bearings (3 and 5 ton); hook col-
lar journals (3 and 5 ton); dead end stud (3, 5 and 10 ton); bearing
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
pin (10 ton).
NOTE: To assure extra long life and top performance, be sure
to lubricate the various parts of the hoist using the lubricants
specified above. If desired, these lubricants may be purchased
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
per hoist of Molykote BR-2-S (Dow Corning Corp.) grease or equiv-
alent—threads of handwheel; gears; liftwheel rollers; gear bearing
rollers; journals of chain guide and dead end pin; sheave wheel
rollers (3, 5 and 10 ton); hook ball bearings (3 and 5 ton); hook col-
lar journals (3 and 5 ton); dead end stud (3, 5 and 10 ton); bearing
surface of hook knob (10 ton); hook block pin (10 ton); and hanger
When the hoist is disassembled for periodic inspections, check the
pawl for free movement and apply a light coat of WD-40 (WD-40
Co.) lubricant to the pawl stud.
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
per hoist of Molykote BR-2-S (Dow Corning Corp.) grease or equiv-
alent—threads of handwheel; gears; liftwheel rollers; gear bearing
rollers; journals of chain guide and dead end pin; sheave wheel
or lubricant on the braking surfaces. When lubricating parts
adjacent to the brake, do not use an excessive amount of lubri-
cant which could seep onto the brake surfaces.
When the hoist is disassembled for periodic inspections, check the
pawl for free movement and apply a light coat of WD-40 (WD-40
When the hoist is disassembled for cleaning or repairs, the following
locations should be lubricated using approximately 1 oz. (29.5mL)
The hoist normally requires no additional lubrication, except for peri-
odically lubricating the load chain as indicated above or when the
unit is disassembled for periodic inspections, cleaning or repairs.
The brake is designed to operate dry. Do not use any grease
or lubricant on the braking surfaces. When lubricating parts
adjacent to the brake, do not use an excessive amount of lubri-
cant which could seep onto the brake surfaces.
When the hoist is disassembled for periodic inspections, check the
pawl for free movement and apply a light coat of WD-40 (WD-40
The hoist normally requires no additional lubrication, except for peri-
odically lubricating the load chain as indicated above or when the
unit is disassembled for periodic inspections, cleaning or repairs.
The brake is designed to operate dry. Do not use any grease
or lubricant on the braking surfaces. When lubricating parts
Never use used motor oils as a chain lubricant. Only use
Lubriplate Bar and Chain Oil 10-R as a lubricant for the load
should never be repaired.
HAND CHAIN
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be assembled to handwheel free from twists with
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be assembled to handwheel free from twists with
weld on vertical link facing inward towards handwheel and weld on
horizontal link facing towards the handwheel side plate.
Care must be taken to assure that there is no twist in the hand chain
Also, load chains are specially heat treated and hardened and
should never be repaired.
HAND CHAIN
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be assembled to handwheel free from twists with
weld on vertical link facing inward towards handwheel and weld on
horizontal link facing towards the handwheel side plate.
Care must be taken to assure that there is no twist in the hand chain
Hand chain should be assembled to handwheel free from twists with
necting links must not be made by cutting the weld side of a stan-
Hand chain should be assembled to handwheel free from twists with
weld on vertical link facing inward towards handwheel and weld on
horizontal link facing towards the handwheel side plate.
Hand chain should be assembled to handwheel free from twists with
weld on vertical link facing inward towards handwheel and weld on
horizontal link facing towards the handwheel side plate.
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
Hand chain should be cleaned, inspected and gaged in the same
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be cleaned, inspected and gaged in the same
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
Hand chain should be cleaned, inspected and gaged in the same
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
dard hand chain link.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
necting links must not be made by cutting the weld side of a stan-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
necting links must not be made by cutting the weld side of a stan-
necting links must not be made by cutting the weld side of a stan-
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
dard hand chain link.
changing chain length. Please note that opening and closing of the
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
connecting link more than twice is not recommended. Also, con-
necting links must not be made by cutting the weld side of a stan-
As received from the factory, the hand chain contains an unwelded
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
link. This link can be placed in a vise and twisted open to facilitate
changing chain length. Please note that opening and closing of the
should never be repaired.
HAND CHAIN
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
Hand chain should be cleaned, inspected and gaged in the same
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
Hand chain should be cleaned, inspected and gaged in the same
HAND CHAIN
Hand chain should be cleaned, inspected and gaged in the same
manner as load chain.
manner as load chain.
manner as load chain.

2. The intermediate gears (622-8) have timing marks (letter “O”
stamped on one tooth). The gears must be assembled with these
marks orientated as shown below.
3.For proper operation, the correct number of rollers must be in-
stalled at the rotating points of the liftwheel, intermediate gears,
hook block sheave (3, 5 and 10 ton) and hoist hanger sheave (10
ton). Also, on the 3 and 5 ton units, the correct number of bearing
balls must be installed in the hook collar to retain the hook and in-
sure proper loading. Refer to Disassembly Instructions above for
the number of rollers at these locations. Applying grease, Molykote
BR - 2 - S (Dow Corning Corp.) or equal EP grease, to the rollers or
bearing balls will help hold them in position during assembly.
4. When assembling the latch to the hook, the end of the rivet
must be peened over. When peening over the rivet, only apply
enough force to form the head and retain the rivet. Excessive force
will deform the latch and make the latch inoperable.
REEVING LOAD CHAIN
A. 1/2, 1, 2, 3, 5 and 10 Ton Hoists
Attach approximately 20”(508mm) of soft wire to the loose end of
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
B. 3 and 5 Ton Hoists
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 5 feet (1.5M )
long. Run chain thru the hook block (first link around the sheave
must stand on edge) and up to the dead end block (622-26). Se-
cure chain to dead end block using the stud, nut and cotter pin.
Refer to illustration below.
10 Ton Hoist
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 20 feet (6M)
long. Run the chain thru the hook block (first link around the sheave
must stand on edge) around the first hook block sheave, up around
the hanger sheave, down around the second hook block sheave
and up to the hoist hanger. Secure the chain to the hoist hanger
using the dead end stud, nut and cotter pin (622-38). Refer to Illus-
tration below.
EXTERIOR FINISH
The exterior surfaces of the hoists have a durable, scratch resistant
finish. Normally, the exterior surfaces can be cleaned by wiping with
a cloth. However, if the finish is damaged, compatible touch-up
paint can be purchased from BUDGIT. Order one case (12-12 oz.-
354mL aerosol cans) of orange touch-up paint Part Number 84190.
Touch-up paint is only available in case quantities. See below for
ordering information.
6
WARNING
Failure to properly install the load chain between chain guide
and liftwheel may cause the chain to lift out of the liftwheel pock-
ets and allow the load to drop.
TO AVOID INJURY:
Feed load chain between liftwheel and chain guide, as shown
above, before attaching it to the loose end pin.
TIMING
MARKS
CHAIN GUIDE
622-16
LOOSE END PIN
622-15 LIFTWHEEL
622-13
LOOSE
END PIN
DEAD END
BLOCK
LOOSE
END PIN
DEAD END
BLOCK
1
2
4
3
2
1
REEVING
3 & 5 TON
REEVING
10 TON
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
Attach approximately 20”(508mm) of soft wire to the loose end of
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
the hanger sheave, down around the second hook block sheave
and up to the hoist hanger. Secure the chain to the hoist hanger
using the dead end stud, nut and cotter pin (622-38). Refer to Illus-
rection until the load end of the chain is approximately 20 feet (6M)
long. Run the chain thru the hook block (first link around the sheave
must stand on edge) around the first hook block sheave, up around
the hanger sheave, down around the second hook block sheave
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 20 feet (6M)
long. Run the chain thru the hook block (first link around the sheave
long. Run chain thru the hook block (first link around the sheave
must stand on edge) and up to the dead end block (622-26). Se-
cure chain to dead end block using the stud, nut and cotter pin.
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 5 feet (1.5M )
long. Run chain thru the hook block (first link around the sheave
must be peened over. When peening over the rivet, only apply
enough force to form the head and retain the rivet. Excessive force
will deform the latch and make the latch inoperable.
REEVING LOAD CHAIN
A. 1/2, 1, 2, 3, 5 and 10 Ton Hoists
Attach approximately 20”(508mm) of soft wire to the loose end of
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
bearing balls will help hold them in position during assembly.
4. When assembling the latch to the hook, the end of the rivet
must be peened over. When peening over the rivet, only apply
enough force to form the head and retain the rivet. Excessive force
will deform the latch and make the latch inoperable.
sure proper loading. Refer to Disassembly Instructions above for
the number of rollers at these locations. Applying grease, Molykote
BR - 2 - S (Dow Corning Corp.) or equal EP grease, to the rollers or
bearing balls will help hold them in position during assembly.
4. When assembling the latch to the hook, the end of the rivet
must be peened over. When peening over the rivet, only apply
enough force to form the head and retain the rivet. Excessive force
stalled at the rotating points of the liftwheel, intermediate gears,
hook block sheave (3, 5 and 10 ton) and hoist hanger sheave (10
ton). Also, on the 3 and 5 ton units, the correct number of bearing
balls must be installed in the hook collar to retain the hook and in-
sure proper loading. Refer to Disassembly Instructions above for
the number of rollers at these locations. Applying grease, Molykote
BR - 2 - S (Dow Corning Corp.) or equal EP grease, to the rollers or
using the dead end stud, nut and cotter pin (622-38). Refer to Illus-
tration below.
rection until the load end of the chain is approximately 20 feet (6M)
long. Run the chain thru the hook block (first link around the sheave
must stand on edge) around the first hook block sheave, up around
the hanger sheave, down around the second hook block sheave
and up to the hoist hanger. Secure the chain to the hoist hanger
using the dead end stud, nut and cotter pin (622-38). Refer to Illus-
tration below.
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 20 feet (6M)
long. Run the chain thru the hook block (first link around the sheave
must stand on edge) around the first hook block sheave, up around
the hanger sheave, down around the second hook block sheave
and up to the hoist hanger. Secure the chain to the hoist hanger
using the dead end stud, nut and cotter pin (622-38). Refer to Illus-
must stand on edge) and up to the dead end block (622-26). Se-
cure chain to dead end block using the stud, nut and cotter pin.
Refer to illustration below.
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 20 feet (6M)
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 5 feet (1.5M )
long. Run chain thru the hook block (first link around the sheave
must stand on edge) and up to the dead end block (622-26). Se-
cure chain to dead end block using the stud, nut and cotter pin.
The load chain must have an odd number of links. After attaching
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 5 feet (1.5M )
long. Run chain thru the hook block (first link around the sheave
must stand on edge) and up to the dead end block (622-26). Se-
cure chain to dead end block using the stud, nut and cotter pin.
The load chain must have an odd number of links. After attaching
The load chain must have an odd number of links. After attaching
the chain to the loose end pin per above, operate in the hoisting di-
rection until the load end of the chain is approximately 5 feet (1.5M )
LIFTWHEEL
622-13
Attach approximately 20”(508mm) of soft wire to the loose end of
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
WARNING
Attach approximately 20”(508mm) of soft wire to the loose end of
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
WARNING
Failure to properly install the load chain between chain guide
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
by reinstalling the cotter pin and spreading the legs of the cotter pin.
with the weld away from the liftwheel and the second link lays flat on
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
(622-4). until the cotter pin hole is visible. Secure the loose end pin
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
hoisting direction until about 2 feet (0.6M) of chain has passed over
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
to the loose end pin and slide the pin through the last link of the
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
to the loose end pin and slide the pin through the last link of the
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
to the loose end pin and slide the pin through the last link of the
chain. Slide the loose end pin into hole in the handwheel side plate
loose end pin to the side into the gear housing, leaving approxi-
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
mately 1/2”(12.7mm) of the pin protruding from the geared side
plate (622-5). Loop the chain, making sure there are no twists, up
plate (622-5). Loop the chain, making sure there are no twists, up
plate (622-5). Loop the chain, making sure there are no twists, up
the liftwheel. The wire should now be removed from the chain. Re-
move the cotter pin from the loose end pin (622-15) and slide the
loose end pin to the side into the gear housing, leaving approxi-
loose end pin to the side into the gear housing, leaving approxi-
loose end pin to the side into the gear housing, leaving approxi-
loose end pin to the side into the gear housing, leaving approxi-
the chain. Pass the wire over the top of the liftwheel (622-13) and
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
the liftwheel. After the chain has been started, pull hand chain in the
the liftwheel. After the chain has been started, pull hand chain in the
down between the liftwheel and the chain guide (622-16). Position
the chain so that the first, as well as the third, link stands on edge
with the weld away from the liftwheel and the second link lays flat on
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
hoisting direction until about 2 feet (0.6M) of chain has passed over
the liftwheel. After the chain has been started, pull hand chain in the
hoisting direction until about 2 feet (0.6M) of chain has passed over
hoisting direction until about 2 feet (0.6M) of chain has passed over

RECOMMENDED SPARE PARTS
To insure continued operation, it is recommended that two friction
washers for each Series 622 Hand Hoist in service, Key No. 622-
39, be kept on hand at all times to replace friction washers that are
worn, contaminated or glazed. See below for ordering information.
PREVENTIVE MAINTENANCE
In addition to the periodic inspection procedure, a preventive main-
tenance program should be established to prolong the useful life of
the hoist and maintain its dependability and continued safe use.
The program should include the periodic inspections with particular
attention being paid to the lubrication of various components using
the recommended lubricants.
TESTING
Before using, all altered, repaired or used hoists that have not been
operated for the previous 12 months should be tested by the user
for proper operation. First, test the unit without a load and then with
a light load of 50 pounds (23Kg.) times the number of load
supporting chains to be sure that the hoist operates properly and
that the brake holds the load when the hand chain is released. Next
test with a load of 125% of rated capacity. In addition, hoists in
which load sustaining parts have been replaced should be tested
with 125% of rated capacity by or under the direction of an ap-
pointed person and written report prepared for record purposes.
NOTE: For additional information on inspection and testing,
refer to Code B30.16 “Overhead Hoists” obtainable from
ASME Order Department, 22 Law Drive, Box 2300, Fairfield,
NJ 07007-2300, U.S.A.
The following information must accompany all correspondence or
repair parts orders.
1. Hoist Capacity
2. Serial Number -- stamped on the capacity label.
For parts orders also specify:
1. Quantity desired
2. Key Number of Part
3. Part Name
4. Part Number
When ordering replacement parts, consideration should be given to
the need to replace other items, (springs, fasteners, etc.) and items
that may be damaged or lost during disassembly or just unfit for fu-
ture use because of deterioration from age or service.
Parts should be ordered from BUDGIT’s Master Parts Depots con-
veniently located throughout the United States and Canada. Refer
to the inside of the front cover of this manual to locate the Master
Parts Depot nearest you.
GENERAL INFORMATION
7
WARNING
On the 3, 5 and 10 ton units, twisted load chain will cause the
chain to jam in the liftwheel or sheave wheels and this may
break the chain and allow the load to drop.
TO AVOID INJURY:
Check each stage of reeving the chain to be sure it has no
twists.
WARNING
Using “commercial” or other manufacturer’s parts to
repair the BUDGIT Series 622 Hoist may cause load loss.
TO AVOID INJURY:
Use only BUDGIT supplied replacement parts. Parts may
look alike but BUDGIT parts are made of specific materials
or processed to achieve specific properties.
look alike but BUDGIT parts are made of specific materials
or processed to achieve specific properties.
TO AVOID INJURY:
Use only BUDGIT supplied replacement parts. Parts may
Using “commercial” or other manufacturer’s parts to
repair the BUDGIT Series 622 Hoist may cause load loss.
WARNING
Using “commercial” or other manufacturer’s parts to
Parts should be ordered from BUDGIT’s Master Parts Depots con-
veniently located throughout the United States and Canada. Refer
to the inside of the front cover of this manual to locate the Master
that may be damaged or lost during disassembly or just unfit for fu-
Parts should be ordered from BUDGIT’s Master Parts Depots con-
veniently located throughout the United States and Canada. Refer
the need to replace other items, (springs, fasteners, etc.) and items
that may be damaged or lost during disassembly or just unfit for fu-
NOTE: For additional information on inspection and testing,
refer to Code B30.16 “Overhead Hoists” obtainable from
ASME Order Department, 22 Law Drive, Box 2300, Fairfield,
pointed person and written report prepared for record purposes.
NOTE: For additional information on inspection and testing,
refer to Code B30.16 “Overhead Hoists” obtainable from
ASME Order Department, 22 Law Drive, Box 2300, Fairfield,
that the brake holds the load when the hand chain is released. Next
test with a load of 125% of rated capacity. In addition, hoists in
which load sustaining parts have been replaced should be tested
with 125% of rated capacity by or under the direction of an ap-
pointed person and written report prepared for record purposes.
that the brake holds the load when the hand chain is released. Next
look alike but BUDGIT parts are made of specific materials
or processed to achieve specific properties.
Using “commercial” or other manufacturer’s parts to
Use only BUDGIT supplied replacement parts. Parts may
look alike but BUDGIT parts are made of specific materials
or processed to achieve specific properties.
repair the BUDGIT Series 622 Hoist may cause load loss.
Using “commercial” or other manufacturer’s parts to
repair the BUDGIT Series 622 Hoist may cause load loss.
veniently located throughout the United States and Canada. Refer
to the inside of the front cover of this manual to locate the Master
Parts Depot nearest you.
WARNING
Parts should be ordered from BUDGIT’s Master Parts Depots con-
veniently located throughout the United States and Canada. Refer
to the inside of the front cover of this manual to locate the Master
the need to replace other items, (springs, fasteners, etc.) and items
that may be damaged or lost during disassembly or just unfit for fu-
ture use because of deterioration from age or service.
Parts should be ordered from BUDGIT’s Master Parts Depots con-
veniently located throughout the United States and Canada. Refer
to the inside of the front cover of this manual to locate the Master
When ordering replacement parts, consideration should be given to
the need to replace other items, (springs, fasteners, etc.) and items
that may be damaged or lost during disassembly or just unfit for fu-
ture use because of deterioration from age or service.
Parts should be ordered from BUDGIT’s Master Parts Depots con-
When ordering replacement parts, consideration should be given to
the need to replace other items, (springs, fasteners, etc.) and items

KEY
NO.
NO
REQ’D DESCRIPTION
PART NUMBER
RATED LOAD - tons (kg)
1/2 (500) 1 (1000) 2 (2000) 3 (3000) 5 (5000) 10 (10000)
622-1 1 Handwheel Cover w/ Studs 22910Y 22791Y 22812Y
622-2 1 Handwheel 22911 22792 22813
622-3 1 Brake Set (2 Friction Washers, Ratchet & Hub) 22912 22793 22814
622-4 1 Handwheel Side Plate (includes Bearing Race, Pawl &
Pawl Spring) 22913 22794 22925 22931 22935
622-5 1 Geared Side Plate (includes Bearing Race,
2 Bushings & 3 Studs) 22914 22261 22262 22263 22936
622-6 1
Main Hardware Set (2 Gear Cover Nuts, 3 Handwheel
Cover Nuts and Lockwashers, 6 Side Plate Nuts and
Lockwashers)
22775 22796 22817
622-7 1 Gear Cover w/ Studs 22915Y 22797Y 22818Y
622-8 1 Gear Set 22916 22798 22819
622-10 1 Pinion Shaft 22917 22800 22821
622-11 1 Pinion and Liftwheel Hardware Kit (Pinion Shaft Nut,
Cotter Pin and Liftwheel Snap Ring) 22918 22801 22822
622-12 1 Liftwheel Roller Kit (66 Rollers for 1/2 ton, 60 Rollers
for 1 ton, 70 Rollers for 2, 3, 5 & 10 ton) 22781 22802 22823
622-13 1 Liftwheel (includes 2 Bearing Races) 22919 22803 22824
622-14 1 Stripper 22920 22804 22825
622-15 1 Loose End Pin (includes 2 Cotter Pins) 22921 22805 22927
622-16 1 Chain Guide Roller 22922 22806 22827
622-17 1
Upper Hook Assembly (includes Hook w/ Latch, Hook
Block, Clevis Pin & Cotter Pin for 1/2, 1 & 2 ton; Hook
w/ Latch, Hook Block, Bearing Balls & Set Screw for 3
& 5 ton)
22923 22807 22830 22836 22847 —
622-18 1 Lower Hook Assembly (includes Hook w/ Latch, Hook
Block, Screw, Nut & Cotter Pin) 22787 22808 22831 — — —
622-19 1 Latch Kit (Latch, Spring & Rivet) 22928 22929 22930 22933 22934 22937
622-20 2 Gear Cage w/ Bushings 22924 22264 22265
622-21 1 Load Chain (Specify Lift or Length Req’d) 85834 85959 85960
622-22 - Hand Chain (Specify Lift or Length Req’d) 85832
622-23 - Warning Tube 946735
622-24 1 Label Set (Capacity & Warning Labels & 8 Drive
Screws) 22603Y 22604Y 22608Y 22609Y 22610Y 22611Y
622-25 1 Hand Chain Connecting Link 661019
622-26 1 Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Snap Rings) — — — 22839 —
622-28 1 Sheave Shaft — — — 22841 —
622-29 1 Sheave Wheel — — — 22842 —
622-30 1 Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring) — — — 22844 22850 —
622-31 1 Lower Hook Assembly (includes Hook Block, Hook w/
Latch, Bearing Balls, Set Screw & 2 Snap Rings) — — — — — —
622-36 1 Hoist Hanger Kit (Hanger Pin & 2 Cotter Pins) — — — — — 22864
622-38 11 Dead End Kit (Stud, Nut & Cotter Pin) — — — — — 22866
622-39 1 Friction Washer 22867 22868 22869
622-40 1
Hoist Hanger Assembly (includes Hanger, Sheave
Wheel, Hook w/ Latch, Hook Block, Dead End Anchor,
Shafts & Snap Rings
— — — — — 22938
622-41 1 Lower Hook Block Assembly (includes Hook Block,
Hook w/ Latch, Sheave Wheels, Shafts & Snap Rings) — — — — — 22939
8
Hand Chain Connecting Link
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Label Set (Capacity & Warning Labels & 8 Drive
Load Chain (Specify Lift or Length Req’d)
Hand Chain (Specify Lift or Length Req’d)
Lower Hook Assembly (includes Hook w/ Latch, Hook
22787
22923
22805
22806
22823
22824
22822
22823
Latch Kit (Latch, Spring & Rivet)
Gear Cage w/ Bushings
Load Chain (Specify Lift or Length Req’d)
Hand Chain (Specify Lift or Length Req’d)
Label Set (Capacity & Warning Labels & 8 Drive
Lower Hook Assembly (includes Hook w/ Latch, Hook
Block, Screw, Nut & Cotter Pin)
Latch Kit (Latch, Spring & Rivet)
Gear Cage w/ Bushings
Load Chain (Specify Lift or Length Req’d)
Hand Chain (Specify Lift or Length Req’d)
w/ Latch, Hook Block, Bearing Balls & Set Screw for 3
Lower Hook Assembly (includes Hook w/ Latch, Hook
Block, Screw, Nut & Cotter Pin)
Latch Kit (Latch, Spring & Rivet)
Upper Hook Assembly (includes Hook w/ Latch, Hook
Block, Clevis Pin & Cotter Pin for 1/2, 1 & 2 ton; Hook
w/ Latch, Hook Block, Bearing Balls & Set Screw for 3
Lower Hook Assembly (includes Hook w/ Latch, Hook
Upper Hook Assembly (includes Hook w/ Latch, Hook
Block, Clevis Pin & Cotter Pin for 1/2, 1 & 2 ton; Hook
w/ Latch, Hook Block, Bearing Balls & Set Screw for 3
22922
Upper Hook Assembly (includes Hook w/ Latch, Hook
Block, Clevis Pin & Cotter Pin for 1/2, 1 & 2 ton; Hook
22781
22919
22920
22804
22921
22805
22922
22800
22918
22802
22803
22797Y
22798
22800
22818Y
22819
22931
22263
22817
22818Y
22814
22931
22936
622-24
1
Label Set (Capacity & Warning Labels & 8 Drive
Screws)
622-25
1
Hand Chain Connecting Link
622-26
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Snap Rings)
622-28
Sheave Shaft
622-29
622-30
Sheave Shaft
Sheave Wheel
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
622-31
1
Lower Hook Assembly (includes Hook Block, Hook w/
Latch, Bearing Balls, Set Screw & 2 Snap Rings)
622-36
1
Hoist Hanger Kit (Hanger Pin & 2 Cotter Pins)
622-38
11
Dead End Kit (Stud, Nut & Cotter Pin)
Warning Tube
622-24
Label Set (Capacity & Warning Labels & 8 Drive
622-25
Hand Chain Connecting Link
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Lower Hook Assembly (includes Hook Block, Hook w/
Latch, Bearing Balls, Set Screw & 2 Snap Rings)
622-36
Hoist Hanger Kit (Hanger Pin & 2 Cotter Pins)
622-38
Dead End Kit (Stud, Nut & Cotter Pin)
1
Friction Washer
Lower Hook Assembly (includes Hook Block, Hook w/
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Lower Hook Assembly (includes Hook Block, Hook w/
Latch, Bearing Balls, Set Screw & 2 Snap Rings)
Hoist Hanger Kit (Hanger Pin & 2 Cotter Pins)
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Lower Hook Assembly (includes Hook Block, Hook w/
Latch, Bearing Balls, Set Screw & 2 Snap Rings)
Hoist Hanger Kit (Hanger Pin & 2 Cotter Pins)
Hand Chain Connecting Link
Hand Chain Connecting Link
Hand Chain Connecting Link
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
622-30
622-29
1
622-29
622-30
622-30
Hand Chain Connecting Link
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Snap Rings)
1
Sheave Shaft
Sheave Wheel
622-30
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Lower Hook Assembly (includes Hook Block, Hook w/
622-30
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Snap Rings)
Sheave Shaft
Sheave Wheel
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Lower Hook Assembly (includes Hook Block, Hook w/
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
1
622-30
622-30
Lower Hook Assembly (includes Hook Block, Hook w/
Dead End Kit (includes 2 Anchor Plates, Stud, Nut & 2
Snap Rings)
1
Sheave Shaft
1
Sheave Wheel
622-30
1
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Snap Rings)
Snap Rings)
1
1
Sheave Shaft
Sheave Wheel
Sheave Shaft Hardware Kit (29 Rollers & 2 Snap Ring)
Snap Rings)
Snap Rings)
Hand Chain Connecting Link
1
1
622-29
622-30
Hand Chain Connecting Link
1
622-29
622-30
Hand Chain Connecting Link
622-30
622-29
622-29
622-29
622-29
622-28
1
1
1
1
1

PART NUMBERS FOR PACKAGED LUBRICANTS
Used in the Series 622 Hand Hoists
(Refer to page 6 for Lubrication Instructions)
Lubricant
Usage
Type of
Lubricant
Part Numbers and Packaged
Quantities of Lubricants
Gears, Rollers of Liftwheel and
Gear Bearings
Grease (Molykote BR-2-S
or Equal)
28606 - 1/2 lb.(.23Kg.) can
28618 - 1 lb.(.46Kg.) can
Pawl Stud Oil (WD-40 or Equal) Obtain locally—not stocked by
BUDGIT
Load Chain Oil (Lubriplate Bar and
Chain Oil 10-R or Equal)
28608 - 1 pint (.5L) can
28619 - 1 gal.(3.8L) can
622-40 - 10 ton Hoist Hanger
Assembly. Except for Latch
Kit, Hoist Hanger Kit & Dead
End Kit, individual parts are
not available for repairs.
622-40 - 10 ton Hoist Hanger
Assembly. Except for Latch
Kit, Hoist Hanger Kit & Dead
End Kit, individual parts are
not available for repairs.
3 & 5 Ton Lower
Hook Block
1/2, 1 & 2 Ton
Lower Hooks
1/2, 1 & 2 Ton
Upper Hooks
3 & 5 Ton
Upper Hooks
9
1/2, 1 & 2 Ton
Lower Hooks
PART NUMBERS FOR PACKAGED LUBRICANTS
Lubricant
Usage
Gears, Rollers of Liftwheel and
PART NUMBERS FOR PACKAGED LUBRICANTS
Lubricant
Usage
Gears, Rollers of Liftwheel and
Gear Bearings
Lubricant
Usage
Lubricant
Usage

Note: When ordering parts, always furnish rated load and serial number of hoist on which the parts are
to be used.
To quickly obtain the name of the Master Parts Depot or Service Center located nearest you,
call [phone]. Fax: [phone].
LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES
THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MER-
CHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE, NO PROMISE OR AFFIRMATION OF FACT MADE
BY ANY AGENT OR REPRESENTATIVE OF SELLER SHALL
CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE TO
ANY LIABILITY OR OBLIGATION.
Seller warrants that on the date of delivery to carrier the goods
are free from defects in workmanship and materials.
SELLER’S SOLE OBLIGATION IN THE EVENT OF BREACH OF
WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR OTH-
ERWISE WITH RESPECT TO GOODS SOLD SHALL BE EX-
CLUSIVELY LIMITED TO REPAIR OR REPLACEMENT, F.O.B.
SELLER’S POINT OF SHIPMENT, OF ANY PARTS WHICH
SELLER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller
determines that such repair or replacement is not feasible, to a re-
fund of the purchase price upon return of the goods to Seller.
Any action against Seller for breach of warranty, negligence or
otherwise, must be commenced within one year after such cause
of action occurs.
NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE
GOODS SHALL BE VALID OR ENFORCEABLE UNLESS
BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY
SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising out
of the use of the goods if, prior to such damage, injury or loss,
such goods are:
(1) damaged or misused following Seller’s delivery to carrier; (2)
not maintained, inspected, or used in compliance with applicable
law and Seller’s written instructions and recommendations; or (3)
installed, repaired, altered or modified without compliance with
such law, instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
UNIFORM COMMERCIAL CODE.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
directions set forth in instructions and manuals furnished by Seller
and shall use and require its employees to follow such instruc-
tions and manuals and to use reasonable care in the use and
maintenance of the goods. Buyer shall not remove or permit any-
one to remove any warning or instruction signs on the goods. In
the event of personal injury or damage to property or business
arising from the use of the goods, Buyer shall within 48 hours
thereafter give Seller written notice of such injury or damage.
Buyer shall cooperate with Seller in investigating any such injury
or damage and in the defense of any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or damage
is caused, in whole or in part, by Buyer’s failure to comply with
applicable federal or state safety requirements, Buyer shall in-
demnify and hold Seller harmless against any claims, loss or ex-
pense for injury or damage arising from the use of the goods.
Budgit Hoists • 414 West Broadway Ave • Muskegon, MI 49443-0769
Phone: [phone] • Fax: [phone] • www.budgithoists.com
Printed in USA
Copyright 2008, Yale-Lift-Tech division of Columbus Mckinnon Corporation
WARNING
Alterations or modifications of equipment and use of non-factory
repair parts can lead to dangerous operation and injury.
TO AVOID INJURY:
• Do not alter or modify equipment.
• Do use only factory replacement parts.
pense for injury or damage arising from the use of the goods.
demnify and hold Seller harmless against any claims, loss or ex-
pense for injury or damage arising from the use of the goods.
If Buyer fails to comply with this section or if any injury or damage
is caused, in whole or in part, by Buyer’s failure to comply with
applicable federal or state safety requirements, Buyer shall in-
demnify and hold Seller harmless against any claims, loss or ex-
Buyer shall cooperate with Seller in investigating any such injury
or damage and in the defense of any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or damage
is caused, in whole or in part, by Buyer’s failure to comply with
one to remove any warning or instruction signs on the goods. In
the event of personal injury or damage to property or business
arising from the use of the goods, Buyer shall within 48 hours
thereafter give Seller written notice of such injury or damage.
and shall use and require its employees to follow such instruc-
tions and manuals and to use reasonable care in the use and
maintenance of the goods. Buyer shall not remove or permit any-
one to remove any warning or instruction signs on the goods. In
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
directions set forth in instructions and manuals furnished by Seller
and shall use and require its employees to follow such instruc-
tions and manuals and to use reasonable care in the use and
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
Buyer shall comply with and require its employees to comply with
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
law and Seller’s written instructions and recommendations; or (3)
installed, repaired, altered or modified without compliance with
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
not maintained, inspected, or used in compliance with applicable
Seller shall not be liable for any damage, injury or loss arising out
of the use of the goods if, prior to such damage, injury or loss,
BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY
SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising out
of the use of the goods if, prior to such damage, injury or loss,
NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE
GOODS SHALL BE VALID OR ENFORCEABLE UNLESS
BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY
SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising out
of the use of the goods if, prior to such damage, injury or loss,
Any action against Seller for breach of warranty, negligence or
otherwise, must be commenced within one year after such cause
or damage and in the defense of any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or damage
is caused, in whole or in part, by Buyer’s failure to comply with
applicable federal or state safety requirements, Buyer shall in-
demnify and hold Seller harmless against any claims, loss or ex-
determines that such repair or replacement is not feasible, to a re-
arising from the use of the goods, Buyer shall within 48 hours
thereafter give Seller written notice of such injury or damage.
Buyer shall cooperate with Seller in investigating any such injury
or damage and in the defense of any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or damage
and shall use and require its employees to follow such instruc-
tions and manuals and to use reasonable care in the use and
maintenance of the goods. Buyer shall not remove or permit any-
one to remove any warning or instruction signs on the goods. In
the event of personal injury or damage to property or business
arising from the use of the goods, Buyer shall within 48 hours
thereafter give Seller written notice of such injury or damage.
Buyer shall cooperate with Seller in investigating any such injury
or damage and in the defense of any claims arising therefrom.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
directions set forth in instructions and manuals furnished by Seller
and shall use and require its employees to follow such instruc-
tions and manuals and to use reasonable care in the use and
maintenance of the goods. Buyer shall not remove or permit any-
one to remove any warning or instruction signs on the goods. In
the event of personal injury or damage to property or business
arising from the use of the goods, Buyer shall within 48 hours
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
UNIFORM COMMERCIAL CODE.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
directions set forth in instructions and manuals furnished by Seller
and shall use and require its employees to follow such instruc-
such law, instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
UNIFORM COMMERCIAL CODE.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
(1) damaged or misused following Seller’s delivery to carrier; (2)
not maintained, inspected, or used in compliance with applicable
law and Seller’s written instructions and recommendations; or (3)
installed, repaired, altered or modified without compliance with
such law, instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS
THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE
(1) damaged or misused following Seller’s delivery to carrier; (2)
not maintained, inspected, or used in compliance with applicable
law and Seller’s written instructions and recommendations; or (3)
installed, repaired, altered or modified without compliance with
(1) damaged or misused following Seller’s delivery to carrier; (2)
• Do not alter or modify equipment.
• Do use only factory replacement parts.
• Do not alter or modify equipment.
• Do use only factory replacement parts.
Alterations or modifications of equipment and use of non-factory
repair parts can lead to dangerous operation and injury.