Buffalo BS-GS2008P User manual

BS-GS2008P/BS-GS2016P/BS-GS2024P
Business switch ................................................................................ 1
Power cable ....................................................................................... 1
AC adapter (BS-GS2008P only)................................................... 1
19 inch rack metal fittings
(BS-GS2016P, BS-GS2024P only)..............................................2
19 inch rack metal fittings screws
(BS-GS2016P, BS-GS2024P only)..............................................8
- Keep the warranty statement at hand to request covered repairs.
- Unless clearly permitted in the product documentation, do not use
other accessories (such as cables) with this product other than
those included in the package.
Screws for 19 inch rack
(BS-GS2016P, BS-GS2024P only)..............................................4
Power cable retaining band ........................................................1
Rubber feet........................................................................................ 4
Serial number label......................................................................... 1
Warranty statement........................................................................ 1
Package Contents
Diagrams and Layout
1. Diag LED On (green): The switch is in normal condition.
On (red): Booting, executing self-diagnostic, or initializing.
Blinking (red): A fan error occurred. (BS-GS2016P/2024P only)
Slow blinking (red): A loop is detected.
7. SFP Ports
(BS-GS2016P,
BS-GS2024P only)
Front
Quick Setup Guide
On (green): Power is on.
Off: Power is off.
2. Power LED
On (green): 1000 Mbps link.
On (amber): 100 Mbps link.
Off: 10 Mbps link or no link.
4. Speed LEDs
5. Link/Act LEDs On: Link is established.
Blinking: Transmitting data.
Off: Link is not established.
6. PoE Ports These Ethernet ports support PoE. Connect devices that need
Ethernet power to these ports.
Connect your SFP modules to these ports.
8. Reset Button Press and holdthis button for 3 seconds to initialize the switch.
The figure below is an example of BS-GS2016P.
2. Installation
Floor or Shelf Mounting
Attach the supplied rubber feet to the bottom corners of the unit before use.
Notes:
- Place the switch on a flat surface near the AC inlet. Set it more than 2 inches from
the wall for aeration.
- To use multiple switches in a stack, attach the rubber feet to each switch and
stack them on top of each other.
Install metal fittings on the switch
by using screws for 19 inch rack.
Remove rubber feet if attached.
Use 4 metal fittings screws to fix the
switch on the rack.
Wall Mounting
To mount the unit to a wall, use 2 screws (not
included) with the dimensions shown on the right.
Screws should be installed with distance apart as
below. Slide the mounting holes on the base of the
switch over them.
BS-GS2008P: 3.34 inches
BS-GS2016P: 7.01 inches
BS-GS2024P: 11.07 inches
Mounting to a Metal Surface (BS-GS2008P, BS-GS2016P only)
To mount to a metal surface, such as the side of a steel desk, use the
"BS-MGK-A Magnet Kit" (sold separately).Attach the supplied rubber feet
to the bottom corners of the unit before using the magnet kit.
Notes:
- Do not put oppy discs, magnetic cards, or other magnetic storage media near
magnets. Doing so may delete or corrupt data.
- The magnet kit is not compatible with the BS-GS2024P.
- If the switch is secured by the magnet alone, it should be no more than 75 cm
(29.5 in) from the oor.
- Do not to install the switch with the fan on bottom for safety.
Installing on 19-inch Rack (BS-GS2016P, BS-GS2024P Only)
For BS-GS2016P and BS-GS2024P, install as shown in the figure below by using
the supplied mounting brackets.
Notes:
- Confirm that the temperature inside of the rack is within range of the operating
environment.
- Do not stack another device on top of the switch installed on the rack.
- Do not let the power supply circuit of the rack overload.
- Make sure that the switch installed on the rack is grounded.
1. Install Business Switch Configuration Tool
Install “Business Switch Configuration Tool” to access Settings easily.
Connect the AC adapter or power cable to the switch.
Confirm that the power LED is on.
Boot your Windows PC connected to the Internet.
Access the following URL and download the “Business Switch Configuration Tool”.
BS-GS2008P: http://d.buffalo.jp/BS-GS2008P/
BS-GS2016P: http://d.buffalo.jp/BS-GS2016P/
BS-GS2024P: http://d.buffalo.jp/BS-GS2024P/
Double-click the file. Open the folder and double-click ”BSSet2_Setup.exe”.
Follow the installer screens. Refer to“3. Open Settings” on overleaf to continue.
Decide where to install the switch and follow the procedure below.
Rear
Quick setup guide........................................................................... 1
For BS-GS2008P
On (green): PoE power is available.
On (amber): Overcurrent, excessive power draw or any other
error.
Off: PoE power is disabled.
3. PoE LEDs
For BS-GS2016P/BS-GS2024P
0.08
0.12
φ0.24
1
2
4 5 678
1
1
2
3
4
2
3
2
1
3
Power cable retaining band Power cable Power cable retaining band
Secure the AC adapter
cable with the cable
retainer.
Screws for 19
inch rack
Metal fittings screws
35020564-01

Technical Specifications
Specifications
Switch Name BS + switch’s MAC address
IP Address 192.168.1.254
Username/Password admin/password
Up to 9 KB
16,384
Buer Capacity 1.5 MB
Default Settings
Throughput
Jumbo Frame
MAC Address Table
Standards
14,881 packets/second（10BASE-T）
148,810 packets/second（100BASE-TX）
1,488,095 packets/second（1000BASE-T）
2014-07
IEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX),
IEEE802.3ab (1000BASE-T), IEEE 802.1Q VLANs, IEEE
802.3ad Link Aggregation Control Protocol (LACP),
IEEE802.3x (flow control), IEEE802.1X (RADIUS), IEEE
802.1D spanning tree
LAN Transmission Rate 10/100/1000 Mbps
Switching Method Store and forward
Transmission Encoding 8B1Q4/4D-PAM5 (1000BASE-T)
4B5B/MLT-3 (100BASE-TX)
Manchester encoding (10BASE-T)
Access Method CSMA/CD
Connect the switch to your PC with an Ethernet cable (sold separately). Confirm
that link/act LED of the connected port is on.
Password Notice
Do not lose the switch's password, or you will not be able to configure settings. If you
lose the password, press and hold the reset button for 3 seconds to initialize all switch
settings. If the reset button is disabled, contact Buffalo technical support.
BS-GS2008P: 8 PoE
BS-GS2016P: 16 PoE + 2 SFP
BS-GS2024P: 24 PoE + 2 SFP
Ports
10BASE-T: two-pair category 3 or higher UTP cable
100BASE-TX: two-pair category 5 or higher UTP cable
1000BASE-T: four-pair category 5e or higher UTP cable
Compatible Cables
Transmission Distance 100 m
Connector RJ-45
AC Power AC 100-240 V 50/60 Hz
BS-GS2008P: 117.9 W (Max)
BS-GS2016P: 243.9 W (Max)
BS-GS2024P: 248.9 W (Max)
Power Consumption
BS-GS2008P: 8.46 (W) x 1.69 (H) x 5.12 (D) in
BS-GS2016P: 12.99 (W) x 1.69 (H) x 9.09 (D) in
BS-GS2024P: 17.32 (W) x 1.69 (H) x 10.12 (D) in
Dimensions
BS-GS2008P: About 29.9 oz
BS-GS2016P: About 101.6 oz
BS-GS2024P: About 132.6 oz
Weight
Operating Environment 0-50°C (32-104°F), 10-85% (non-condensing)
Acquired Standards VCCI Class A, FCC Class A, Canada IC Class A, UL
Subnet Mask 255.255.255.0
Default Gateway 0.0.0.0
3. Open Settings
Access Settings to change or confirm your switch’s settings.
Double-click the ( ) icon to open Business Switch
Configuration Tool.
Click Next to start searching for the switch.
Select the switch and click Next.
Click Change IP Address.
Click OK to launch a web browser and display the login screen.
Enter “admin” as the username and “password”as the password, then click Log In.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Settings will be displayed. To configure switch settings, refer to user manual. The
user manual can be downloaded from the URL below.
Click Back to Select Switch and select the switch again; click Next, then click
Settings (Web Admin Interface).
Configure the switch’s IP address to match the segment of the IP address of your
PC and click Next. If the password input screen is displayed, enter “password”
and click Next.
BS-GS2008P: http://d.buffalo.jp/BS-GS2008P/
BS-GS2016P: http://d.buffalo.jp/BS-GS2016P/
BS-GS2024P: http://d.buffalo.jp/BS-GS2024P/
PoE BS-GS2008P: 30 watts per port, 90 watts total
BS-GS2016P: 30 watts per port, 180 watts total
BS-GS2024P: 30 watts per port, 180 watts total
5
8
9
1
2
3
4
6
7