BURG-WACHTER PointSafe User manual

OPERATING INSTRUCTIONS
FOR USE OF POINT SAFE WITH
DIGITAL LOCK
Please keep your codes and emergency keys in a •
safe place – but not in the safe!
Do not use any personal dates (e.g. birthday, •
telephone no. ....)
If the safe is unlikely to be used for a long time, •
remove batteries.
For hotels: See text below on the right hand side •
and attached guest code instructions.
For your own security, change both master code •
and user code from their factory settings.
If further advice is required, please contact your •
local retailer or Security Centre.
IMPORTANT ADVICE
Slide cover plate marked ‘Point Safe’ away from
keypad to the right hand side in order to reveal the
keyhole.
Turn the key clockwise until the stop. The door opens
automatically. Turn the key back anti-clockwise – the
bolts will extend again – and remove the key. Remove
the battery cover on the inside of the door. Insert 5
batteries LR6/AA/1.5V/Alkaline.
ATTENTION: When new batteries are required the
LCD display shows ‘LO BATT’. All 5 batteries have to
be replaced then. Please see that the batteries will be
disposed ecofriendly.
USING YOUR POINT SAFE FOR THE FIRST TIME
Press the “Enter“ button. Enter the user code
(factory code 168) and press the “Enter“ button.
The door opens automatically.
OPENING OF THE SAFE
The door has to be open and the bolts have to be
engaged. Press the ”Enter“ button, the LCD will
display ”Code”, enter the new user code (1- max.
6 digits), press the ”Enter“ button and then the
”Close“ button. The door closes automatically.
CHANGING TO A NEW USER CODE
In a closed state the safe will not accept any incorrect
codes. In such a case the LCD will show ”ERROR“
and short tones can be heard. If an incorrect code is
entered three times the electronic will block the safe
for 5 minutes.
Once this period has passed the safe can be opened
with the master code as well as with the correct
user code. If an incorrect digit has been entered by
mistake it can be deleted by pressing the ”Close“
button.
INCORRECT CODES
The door will close automatically when the “Close“
button is pressed.
ATTENTION: In case the door is blocked by an
obstacle, the LCD will display ”BLOCK“. The safe
cannot be closed then. Remove the obstacle and try
again.
CLOSING THE SAFE
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
www.burg-waechter.de
11
Point Safe < 03-2006

2
The bolts have to be extended. Press the ”SET“
button – the hour display is blinking.
Press the ”H/M“ button until the required hour is
displayed.
(Hour display: A 1-12 = 1-12 o´clock, P 1-12 = 13-24
o´clock). Press the ”SET“ button – the minute display
is blinking. Press the ”H/M“ button again until the
required minute is displayed. For conrmation press
the ”SET“ button.
CLOCK TIME ADJUSTMENT
The safe reaches its intended protective function only
after it has been xed to a massive part of a building.
Please use the marked xing points (at the wall and/
or on the oor) in order to secure the necessary local
connection.
INSTALLATION
Press the ”Enter“ button, enter the master code
(factory code 12345678) and press the ”Enter“
button again. The LCD will show ”PASS 1“, starting
a 10 second count. Once this period has passed the
user code will be displayed for a short moment and
the door opens automatically. ATTENTION: In order
to close the safe the user code must be entered
anew (see also “Changing to a new user code”).
OPENING THE SAFE WITH THE MASTER CODE
Subjet to errors and changes.
Point Safe < 03-2006
If you want to use the safe in the Hotel version, it can
be shifted form the normal mode to the Hotel mode
with the master code. The door has to be opened
and the bolts have to be extended. Press ”Enter“,
enter your 8-digit master code and press “Enter“
again. The LCD shows ”PASS 1“, starting a 10 second
count. Press the ”Enter“ button within this 10 sec.
period, enter the code ”16805“ and conrm the
shifting by pressing ”Enter“. The LCD shows
”SET-05“. If now the door remains open for more
than 5 minutes, the user code has to be entered
again. If you want to shift back to the normal mode
please proceed as mentioned above and use the code
“16800” in the according point. ”SET-00“ will appear
on the LCD and the user code will be valid indenitely
also when the door is open.
SPECIAL FEATURE HOTEL VERSION:
Power supply: 5 x LR6/AA/1,5V batteries
(Alkaline)
Working humidity: 20%~95% rH – non-condensed /
non-condensing
TECHNICAL INFORMATION
The door has to be open and the bolts have to be
extended. Press the ”Enter“ button, enter the master
code (factory code 12345678) and press the ”Enter“
button. The LCD will display “PASS 1“, starting a 10
second count. Press the “Enter” button again within
this 10 sec. period. Now enter the new master code
(8 digits), press the ”Enter“ button, enter the new
master code for a second time and press the “Enter“
button once more. If the LCD shows “Good”, the
electronic has now saved the new code.
CHANGING OF THE MASTER CODE