Burley Fireball Springdale 9103 Manual

Page 1 of 20
Installation Instructions
& User Manual
for the super-efficient
Wood Burning Stoves
Cross Section – Artist Impression
Applicable Appliances
Springdale (9103), Debdale (9104), Hollywell (9105),
Brampton (9108) and Wakerley (9112)
Document reference BUR/02/16 Revision date: FEBRUARY 2016
THESE INSTRUCTIONS MUST BE LEFT WITH THE USER
FOR FUTURE REFERENCE

Page 2 of 20
Table of Contents
Approvals.........................................................................................................................................4
TECHNICAL DATA .........................................................................................................................5
Stove Dimensions............................................................................................................................6
Room Sealing Options.....................................................................................................................6
Installation Instructions ....................................................................................................................7
The Clean Air Act 1993 and Smoke Control Areas..........................................................................7
Chimneys, Flues, Hearths and Surrounds.......................................................................................8
Air Supply and Room Sealing Kit.....................................................................................................9
Stove Assembly.............................................................................................................................10
Door Handle Adjustment................................................................................................................10
Door Handle Assembly..................................................................................................................11
Air Lever Assembly........................................................................................................................12
Optional Convection Tube Cover Plate..........................................................................................13
Assembly and Installation of the Stove Fire Bricks and Baffle.......................................................14
Fitting of Stove Bricks....................................................................................................................14
Log Retaining Bar..........................................................................................................................14
Commissioning the Appliance........................................................................................................15
USER INSTRUCTIONS.................................................................................................................15
To Light the Stove..........................................................................................................................15
Recommended fuels & using the Moisture Meter ..........................................................................16
Stove Thermometers - DO NOT USE WITH OUR STOVES..................................................16
Troubleshooting/Poor Appliance Operation...................................................................................16
Reasons for Premature Wear of Internal Parts..............................................................................17
Care of Glass.................................................................................................................................17
Chimney Sweeping and Maintenance............................................................................................18
Safety.............................................................................................................................................18
Warranty........................................................................................................................................19
If you need further help… ..............................................................................................................19
Spare Parts....................................................................................................................................19
Customer & Installation Notes........................................................................................................20
PLEASE CAREFULLY CHECK YOUR STOVE FOR DAMAGE
OR DEFECTS PRIOR TO FITTING.
WE CAN NOT EXCHANGE DAMAGED OR FAULTY
STOVES THAT HAVE BEEN FITTED.

Page 3 of 20
Thank You
Thank you for purchasing a Burley Fireball Wood Burning Stove; we hope you
will be delighted with the super-efficient performance.
Included with your stove is the Burley ‘Thank You Kit’*, which typically contains:-
•A Spanner to attach and adjust the tension of the air control lever
•A Coaster to protect the top of your stove
•Four Hearth Protectors to place under the stove legs (Black Squares)
•A Moisture Meter to ensure your wood is dry
•Glass Cleaner
•Stove Paint in case you prefer black handles or ever need to touch up any paint work
•A Heat Resistant Glove
•Scoop for removing ash
•An Allen Key should you wish to adjust the door handle
•A Mug to enjoy a cup of tea whilst admiring the fantastic flame picture
The contents of the kits vary from model to model, so not all the items listed or shown above may
be included with your stove.
*Thank You Kit introduced with stoves supplied from October 2013

Page 4 of 20
Features…
Cross Section – Artist Impression
You now own the world’s most efficient stove!
Approvals
All our wood stoves are approved to EN13240:2001 and EN13240 A2:2004.

Page 5 of 20
TECHNICAL DATA
All built to EN13240 Springdale
9103 Debdale 9104 Hollywell 9105 Brampton 9108 Wakerley 9112
Efficiency (Net) 88.9% 89.8% 89.1% 85.5% 84.1%
CO concentration
@ 13% Oxygen 0.1% 0.1% 0.1% 0.1% 0.1%
Requirement of fuels
used in Smoke
Control Areas
Dry logs <20%
H
₂
O Dry logs <20%
H
₂
O Dry logs <20%
H
₂
O Dry logs<20% H
₂
O Dry logs<20% H
₂
O
Maximum length
170 -220mm long Maximum length 200 -250mm long Maximum length 250 -300mm long Maximum length 250 -350mm lonG Maximum length 300 -450mm long
Maximum width
150mm Maximum width 150mm Maximum width 150mm Maximum width 150mm Maximum width 150mm
Lower quality fuel
can be used in non-
smoke controlled
areas, but will not
give the best
efficiencies
Dry Logs
< 25% H
₂
O Dry Logs
< 25% H
₂
O Dry Logs
< 25% H
₂
O Dry Logs
< 25% H
₂
O Dry Logs
< 25% H
₂
O
220mm long 250mm long 310mm long 430mm long 580mm long
Weight in kg 45 kg 57 kg 95 kg 105 kg 130 kg
Nominal kW output 3 kW 4 kW 5 kW 8 kW 12 kW
Max kW output 4.1 kW 5.3 kW 6.4 kW 11.7 kW 18.3 kW
Air vent requirement. Not Required Not Required
550mm sq min in
houses built after
2010, otherwise
not required
1,962mm sq min
50mm diameter 7,850mm sq min 100mm diameter
Air vent not
required if stove is
room sealed
Air vent not
required if stove is
room sealed
Air vent not
required if stove is
room sealed
Minimum flue draught
mm H²O 0.5mm 0.5mm 0.5mm 0.5mm 0.5mm
Flue gas temperature 162 °C 156 °C 122 °C 183 ˚C 237 °C
Spigot Temp. 258 °C 253 °C 241 °C 274 °C 316 °C
Flue size (Top Exit) 127mm (5”) 127mm (5”) 150mm (6”) 150mm (6”) 150mm (6”)
Min. chimney
diameter 127mm (5”) 127mm (5”) 150mm (6”) 150mm (6”) 150mm (6”)
Best chimney
diameter 127mm (5”) 127mm (5”) 150mm (6”) 150mm (6”) 175mm (7”)
Minimum distance to
combustible
materials. All other
distance as per
Building regulations
Part J or HETAS
recommendations
10cm behind (4”)
35cm at side (14”)
35cm to Top
20cm behind (8”)
40cm at side (16”)
40cm to Top
20cm behind (8”)
35cm at side (14”)
35cm to Top
10cm behind (4”)
40cm at side (16”)
40cm to Top
20cm behind (8”)
45cm at side (18”)
45cm to Top
Non combustibles When fitted inside a masonry or similar non-flammable material recess, e.g., fireplace opening, there is no
minimum distance; although we would advise a minimum of 50mm from any surface to allow for convection.
Max Hearth temp. <100 °C <100 °C <100 °C <100 °C <100 °C
Min Hearth thickness 12mm 12mm 12mm 12mm 12mm

Page 6 of 20
Stove Dimensions
Room Sealing Options
40mm D
50mm D

Page 7 of 20
Installation Instructions
When installing these appliances, all local regulations, including those referring to national and
European Standards need to be complied with.
This manual covers the appliances: Burley Models: 9103, 9104, 9105, 9108 and 9112
The nominal space heating output is:
‘Springdale’ 9103: 3Kw ‘Debdale’ 9104: 4Kw
‘Hollywell’ 9105: 5Kw ‘Brampton’ 9108:8Kw ‘Wakerley’ 9112: 12Kw
Any of the above appliances should be installed by an installer registered with a competency
scheme (i.e. HETAS/ELECSA England & Wales), conforming to Building Regulations Part J and
the installation must be registered with the local council building control department.
Failure to comply with the above renders all guarantees and liabilities of the
manufacturer null and void.
By carefully following the instructions below we are certain that you will enjoy many years of
warmth and enjoyment from your new Burley Fireball Stove.
The manufacturer will not guarantee or accept liability for any problem that arises unless a local
authority building control certificate has been completed and a valid receipt or proof of purchase is
presented from the approved supplier.
The appliances should not be fitted closer to combustible materials, e.g. wooden fire surround or
stud wall, than is shown in the table on page 5.
When fitted against a wall made of combustible material e.g. a wooden stud wall with
plasterboard, unless a 75mm thick non-combustible material is used as a barrier, extra non-
combustible material should be fitted behind the stove if the distance from the wall is less than
shown. When fitted inside a masonry or similar non-flammable material recess, e.g., fireplace
opening, there is no minimum distance; although we would advise a minimum of 50mm from any
surface to allow for convection.
The Clean Air Act 1993 and Smoke Control Areas
Under the Clean Air Act local authorities may declare the whole or part of the district of the
authority to be a smoke control area. It is an offence to emit smoke from a chimney of a building,
from a furnace or from any fixed boiler if located in a designated smoke control area. It is also an
offence to acquire an "unauthorised fuel" for use within a smoke control area unless it is used in
an "exempt" appliance ("exempted" from the controls which generally apply in the smoke control
area).
The Secretary of State for Environment, Food and Rural Affairs has powers under the Act to
authorise smokeless fuels or exempt appliances for use in smoke control areas in England. In
Scotland and Wales this power rests with Ministers in the devolved administrations for those
countries. Separate legislation, the Clean Air (Northern Ireland) Order 1981, applies in Northern
Ireland. Therefore it is a requirement that fuels burnt or obtained for use in smoke control areas
have been "authorised" in Regulations and that appliances used to burn solid fuel in those areas
(other than "authorised" fuels) have been exempted by an Order made and signed by the
Secretary of State or Minister in the devolved administrations.
Further information on the requirements of the Clean Air Act can be found here:
https://www.gov.uk/smoke-control-area-rules
Your local authority is responsible for implementing the Clean Air Act 1993 including designation
and supervision of smoke control areas and you can contact them for details of Clean Air Act
requirements
The 9103, 9104, 9105 and 9108 have been recommended as suitable for use in smoke control
areas when burning wood logs.

Page 8 of 20
Chimneys, Flues, Hearths and Surrounds
Chimneys
The 9103 and 9104 require a minimum chimney flue of 5” (125mm), 9105, 9108 and 9112 models
require a minimum chimney flue of 6” diameter (150mm). All chimneys/flues must be a minimum
length of 4 metres and must comply with Building Regulations J. Never share the flue with another
appliance.
If flue and chimney are not to these specifications there could be insufficient draw to pull oxygen
through the appliance to make it burn properly. Due to the low temperature of the exiting flue
gases we recommend that the flue is lined to the diameter specified in the table on page 5.
Larger flues over 200mm particularly ones containing voids may affect appliance performance. We
specify particular size flues for efficient operation of our stoves.
If you live in a valley or are surrounded by tall trees or buildings you might experience
downdraught problems where the wind tries to stop the fumes rising up the chimney. An anti-
downdraught cowl might help, but anti-downdraught cowls reduce the draw.
We recommend you seek the advice of a HETAS (0845 634 5626) or NACE (01526 322 555)
registered supplier and installer before purchasing any stove or heating appliance. It may be wise
to contact your local chimney sweep before the stove is installed.
Flue Pipe
We recommend 1mm stainless steel pipe sprayed matt black. Only use vitreous enamel pipe if it is
stainless steel as mild steel can corrode over time.
Hearths
The stove must stand on a non-combustible surface. Installation standards dictate that hearths
must be at least 12mm thick, but installers must take into account the weight of the stove on such
thin material.
The hearth should extend a minimum of 225mm in front of the stove. When a stove is freestanding
the hearth should always extend a minimum of 150mm either side of the stove.
Aeration hole must
be left open for use
in Smoke Control
areas
Aeration hole can be
closed, if not used in
Smoke Control Areas.

Page 9 of 20
Strength and heat resistance of the hearth.
Stoves are very heavy and most materials used for hearths crack very easily. It is impossible for
Burley to inspect each hearth or comment on every installation, so the onus is on the installer to
ensure the construction of the hearth is suitable for the application. Slate hearths can be
particularly fragile. If in any doubt we recommend sliding a piece of vermiculite or calcium silicate
insulation beneath the stove to protect it from the heat.
As guidance however:
•Do not use boxed and lipped hearths.
•Avoid marble, conglomerate or micro marble hearths.
•Rather than using one large piece of material, use sectional hearths or slabs which will move
independently and allow for expansion due to heat. Should a slab section crack it is then easier
and cheaper to replace.
•Bed hearths down on a level base, not directly on a hard surface which could be uneven.
•If necessary stand the stove on a steel or stone bed to ensure the weight is distributed.
•Do not subject the hearth to sudden impacts by dropping the stove. The stove is heavy and it is
strongly recommended that lifting is undertaken by two people.
•Use the hearth protection squares provided in your Thank You Kit.
Surrounds
Must be capable of withstanding the temperature produced by the stove and comply
with the minimum distances to combustibles.
Air Supply and Room Sealing Kit (Optional)
All hydrocarbon burning appliances require an oxygen/air supply.
If the stove is to be fitted on an external wall the air supply can be taken straight from the outside
by using the optional room sealing kit. A 100mm diameter hole needs to be drilled in the correct
place (138mm above the hearth) to take the 86mm external (80mm internal) duct as supplied with
the kit. This will allow for easy connection. Any gap can be filled in with cement or mastic.
•A proprietary grille is supplied with the kit.
•A room sealing kit which exits horizontally is available.
The room sealing method of supplying air is always to be preferred as heat loss from the room will
be greatly reduced.
If the stove is not on an outside wall or the room sealing kit cannot be used, an air vent must be
supplied in the room in which the stove is fitted. The sizes of the vents required are:
•3Kw – No vent required
•4Kw - No vent required
•5Kw – For homes built before 2010 – no vent required. For homes built after 2010 - 550mm sq
•8Kw - 1650mm sq (50mm diameter)
•12Kw 4950mm Sq (100mm diameter)
Only permanently open vents can be used and consideration should be given to draught when the
stove is not in use, therefore site this vent carefully. The vent covers should comply with Building
Regulations Part J and should be sited where they cannot be blocked.

Page 10 of 20
WARNING
The Burley Fireball series of stoves are primarily for burning wood (this includes logs and
sawdust briquettes). In smoke control areas only wood fuels should be used.
Before purchasing a stove we would strongly advise you seek the advice of a HETAS
installer to ensure suitability of the product to your home.
Other fuels, such as coal (any type), smokeless fuels or petroleum coke can only be used if
the optional multi-fuel grate is fitted (available on models 9104 and 9105 only). Under no
circumstances should liquid fuels be added. It is not an incinerator and rubbish, including
painted or tanalised wood and MDF, should not be burnt in this appliance, doing so is
potentially dangerous and will invalidate any guarantees immediately.
Stove Assembly
Door Handle Adjustment
There is a CAM and LOBE mechanism which allows the handle to be moved up and down or in
and out. If required, adjust the handle so it lines up and engages correctly with the stud in the side
of the stove. Incorrect alignment will put excessive force on the door hinges or will result in a poor
seal between the door and the stove. The door may require adjustment as the rope seal
compresses. A 5mm Allen key will be required.
To adjust the door, loosen off the
socket screw withthe Allen key.
Holding the Allen key, use a spanner
to turn the off centre cam to
position the handle. Hold the
cam in the desired position
whilst tighteningthe screw
with the Allen key.