Bushnell GOLF PRO X3 User manual

Model #: 202250
Rev. 08-22
Android and Google Play are registered trademarks of Google Inc. in the United States
and other countries. iPhone and Apple Store are trademarks of Apple Inc., registered in
the U.S. and other countries. Other names may be trademarks of their respective owners.
Scan the code to download
the Bushnell Golf Mobile app
and register your Pro X3 Laser
Rangender.

Click on each topic in the Table of Contents to go directly to it.
TABLE OF CONTENTS
INTRODUCTION 3
PARTS GUIDE 3
DISPLAY INDICATORS 3
ACTIVATING/REPLACING THE BATTERY 4
BATTERY LEVEL INDICATOR 4
BASIC OPERATION 4
ADJUSTING THE EYEPIECE 4
ACTIVE LASER 4
SLOPE SWITCH TECHNOLOGY 5
SLOPE SWITCH 5
ELEMENTS 5
HOW TO USE SLOPE +/-™ 5
PINSEEKER™ WITH VISUAL JOLT® 6
DISTANCE UNITS: YARDS OR METERS 6
DUAL DISPLAY 6
CONNECTING TO THE BUSHNELL GOLF APP 7
UPDATING FIRMWARE 7
BITE MAGNETIC MOUNT 8
CLEANING AND GENERAL CARE 8
TROUBLESHOOTING 8
TECHNICAL SPECIFICATIONS 9
LANGUAGES
FRANÇAIS 11
ESPAÑOL 18
DEUTSCH 25
ITALIANO 32
PORTUGUÊS 39
DANSK 46
SVENSKA 53
中文60
日本語67
한국어74
BAHASA INDONESIA 81

3
Click to Return to the Table of Contents
PARTS GUIDE
1. Slope Switch
2. Mode Button
3. Power/Fire Button
4. Eyepiece Diopter Dial
5. Battery Compartment
6. Dual Display Button
7. BITE Magnet (see inset photo)
7. BITE MAGNET
5
3
6
2
4
1
DISPLAY INDICATORS
Your Pro X3 display incorporates the following indicators:
1. Aiming Circle (surrounding crosshairs indicate laser transmission)
2. Bluetooth Enabled
3. Bluetooth Connection to App
4. Battery Level
5. Elements Mode
6. “Play As” Distance (based on Slope/Elements)
7. Unit is in “Settings” Mode
8. Slope* (% grade)
9. Line of Sight Distance
10. Visual JOLT Indicator Ring
9
68
4
10
1
2
3
5
7
INTRODUCTION
Congratulations on the purchase of your New Pro X3 Laser Rangender from Bushnell Golf. You are joining 98.6% of Tour
Players that trust their games to Bushnell Golf. The Pro X3 is the latest evolution in our illustrious history of providing
golfers the most accurate distances in golf. The Pro X3 is packed with all our market-leading innovations and takes getting
distances around the course to the next level with our patented Slope with Elements Technology.
Welcome to the Bushnell Golf Family!
WARNING: AS WITH ANY LASER DEVICE, IT IS NOT RECOMMENDED TO DIRECTLY VIEW THE EMISSIONS FOR LONG
PERIODS WITH MAGNIFIED LENSES.

4
Click to Return to the Table of Contents
ACTIVE LASER
Crosshairs surrounding the aiming circle indicate that the laser is transmitted. Once a range is acquired, you can release
the Power/Fire button. The crosshairs surrounding the circle will disappear once the Power/Fire button is released (i.e.,
the laser is no longer transmitted).
ADJUSTING THE EYEPIECE
The Pro X3 has an adjustable Fast Focus eyepiece (+/- 3.5 diopter adjustment) that allows you to focus the displayed data
and icons relative to the viewed image from the monocular optics. Rotate the eyepiece until the display is in focus.
BASIC OPERATION
While looking through the Bushnell Pro X3, press and release the Power/Fire button to activate the display. If the display
icons and numbers are blurry, rotate the eyepiece in either direction until they focus (see "Adjusting the Eyepiece" below).
Next, placing the aiming circle (center of the display) over a target at least 5 yards away, press and hold the Power/
Fire button until the "line of sight" distance is displayed near the bottom of the display (see "Display Indicators" below).
Crosshairs surrounding the aiming circle indicate that the laser is transmitted. After a range is acquired and displayed, you
can release the Power/Fire button. The crosshairs surrounding the aiming circle will disappear once the Power/Fire button
is released (i.e., the laser is no longer transmitted).
Once activated, the display will remain visible and display the last distance measurement for 10 seconds. You can press the Power/Fire button again at any
time to range to a new target. The maximum time the laser is transmitted (active) is ve seconds. To re-re, press the button down again.
BATTERY LEVEL INDICATOR
The Battery Indicator (4) shows the remaining power level:
• Full charge
• Approx. 2/3 battery life remaining
• Approx. 1/3 battery Life remaining
• Battery Indicator Blinks - The battery needs replacing, and the unit will not be operable.
Positive (+)
end facing out
ACTIVATING/REPLACING THE BATTERY
Remove the battery door by lifting the battery door tab and rotating counterclockwise until it is
loose.
Activating the installed battery: A CR2 battery is pre-installed in your new Pro X3. Before using
the rangender, remove the battery door as described above. Remove the plastic protective disc
from the top of the battery, replace the battery door.
Replacing a low battery: Insert a new CR2 3-volt lithium battery into the compartment negative
(at) end rst (positive end facing out towards the battery cover), then replace the battery door.

5
Click to Return to the Table of Contents
HOW TO USE SLOPE +/-™
Move the slope switch to the "Slope On" position. The second row of information appears in the display, conrming that
you are now in slope mode. Next, press the Power/Fire button to obtain the distance to the ag or other objects. Once the
range is displayed, release the Power/Fire button. Once you have released the Power/Fire button, the grade percentage
and compensated range will be displayed beneath the standard distance in the second row of numbers.
For example, if the true distance is 160 yards, but with a slope of -3%, the Slope compensated ("Play As")
range is 156 yards. The display would show this (right):
Slope OffSlope On
A. Slope B. Slope with Elements
THE ADVANTAGE OF SLOPE +/-™ WITH ELEMENTS
A. The distance to the black ag in the drawing below is 160 yards. It is also 160 yards to the red ag, although it is on a
slope with a 6% grade (uphill incline). However, if a golfer were to play this hole at 160 yards, the ball (X) would fall short
of the hole/ag if Slope was not considered. Therefore, due to the Slope, play it as a 168 yard shot.
B. In the drawing below, the golfer is hitting up hill, playing at cooler temperature, and at a course elevation lower than
their Home Elevation. The Slope and Elements compensated distance for this shot is 171 yards.
ELEMENTS
With Slope mode selected, the display will show the percent grade of tilt/incline to the hole or obstacle (with the ag or
other target in the aiming circle) and "Play As" compensated distance below the normal "Line of Sight" distance when the
laser is red. You can also activate the Element feature by pressing the Mode button (toggle between Elements on or off).
"ON" indicates the Elements Mode icon ( ) in the display.
When the Elements Mode is on, the Slope compensated distance also factors in the air pressure and temperature at your
location on the golf course. So, for example, the ball will travel farther through thinner air at higher altitudes (assuming
the ball is hit with the same launch conditions). Note: once the device has shut off, the unit will always default to the last
mode used.
SLOPE SWITCH
Slope is enabled by sliding the Slope Switch on the top of the Pro X3.
To move the Slope Switch on or off:
1. Use the right thumb to pull down the side latch.
2. With the left hand, pull back the switch on both sides to enable
Slope On or slide forward to turn Slope off.
3. Release the side latch to keep the switch in place.
The Slope +/- mode will automatically compute an angle compensated range based upon distance and Slope determined
by the laser rangender and built-in inclinometer, when a target is ranged. This data combines internal algorithmic
formulas dealing with average club use and ball trajectories. The angle compensated range provides direction in playing
the shot (i.e., add distance if an incline, subtract distance if a decline). For your Pro X3 to conform to USGA Rule 14-3,
the Slope compensated ranging feature must be in the Off position.
SLOPE SWITCH TECHNOLOGY
Slope Switch technology lets the golfer easily turn Bushnell's patented Slope function on and off. This technology allows the
golfer to conveniently utilize Slope to get compensated distances around the course when they want it and have a USGA
conforming device that is legal for tournament play when they need it.

6
Click to Return to the Table of Contents
Dual Display Button Black Display Red Display
Settings
can also
be accessed
through the
Bushnell Golf
App!
Home Elevation
Adjustment Screen
ft
Home Elevation
Number Selection
Screen
ft
HOME ELEVATION
To customize your Elements compensated distances for your game, you will want to set the home
elevation setting to where you play most often. Adjusts for pressure changes wherever you are playing.
We suggest adjusting Home Elevation in the Bushnell Golf app.
To set the Home Elevation in the Pro X3 Set Up menu:
DUAL DISPLAY
To adjust the Dual Display from Black to Red, press the button on the left side of
the rangender.
DISTANCE UNITS: YARDS OR METERS
To set the distance units between Yards or Meters, press Fire/Power to turn the unit on, then press and hold the Mode
button until the display is blinking. Press the Mode to switch from Y (yards) or M (meters). Press Fire/Power button to set
the distance units.
Note: If the Red Display is being used, the rst setting is to adjust the Display Brightness. The second setting is to select the Distance Units. Follow the
instructions above to complete.
PINSEEKER™ WITH VISUAL JOLT®
Ever had trouble getting the distance to the ag? This advanced mode allows easy ag acquisition without inadvertently
getting distances to background targets (i.e., trees) with stronger signal strength.
To use PinSeeker™, align the aiming circle reticle onto the ag that you want to measure the distance. Then, press and
hold the Power/Fire button and move the laser slowly across an area until the aiming circle at the center of the display
is located over the ag or desired object. If the laser beam recognized more than one object (i.e., the ag and a group
of trees behind it), only the distance to the closest object (the ag) would be displayed. The JOLT Technology provides
two short pulses to conrm that the distance displayed is to the ag. Then, the red ring around the display (Visual JOLT
Indicator) is activated, conrming the laser has ranged the correct target via PinSeeker™. Sometimes, the laser beam only
sees one object in its path. In this case, the distance is displayed, but no JOLT indication will be provided because more
than one object was not acquired.
TIP: While pressing the Power/Fire button, you can move the device slowly from object to object and intentionally force the laser
to hit multiple objects to ensure that you only display the closest objects recognized by the laser. Once the device has shut off,
the unit will always default to the last mode used.
*For ease of use, the device will always be in PinSeeker™ Mode.
1. Press and Hold the Mode button on top of the ProX3 to enter Set Up mode.
2. Press the Fire/Power button to move through each setting to the "ELE" blinking screen (see right).
3. Press the Mode button to enter Home Elevation set up. The screen will change to "AdJ" blinking
(see right).
4. Press the Fire/Power button to enter the rst number, this will be indicated by the number
blinking.
5. Press the Mode button to change the number.
6. When the correct number is selected, press Fire/Power and the next number to the right will blink
and can be changed. Continue until the full number is correct for Home Elevation and press
Fire/Power to set.
7. Press Fire/Power to exit Set Up Mode.

7
Click to Return to the Table of Contents
HoleView Screen
UPDATING FIRMWARE
To update the Pro X3 rmware, click on Device Update on the Device Function screen in the Bushnell Golf Mobile app. If
there is an update available, it will automatically be downloaded and installed.
The Bushnell Pro X3 does not need to be connected to the Bushnell Golf App to operate. Using the app makes adjusting
settings easier and the player can save games, stats and course information. See the screenshots below for some of the
features.
*Ensure Bluetooth is enabled on your phone.
CONNECTING TO THE BUSHNELL GOLF APP
Once the Bushnell Golf App is
downloaded and installed on your
phone, follow the instructions on the
App to pair your Pro X3 rangender.

8
Click to Return to the Table of Contents
TROUBLESHOOTING
Never disassemble your laser rangender. Irreparable damage can result from unauthorized service attempts, voiding the
warranty.
If the unit does not turn on, the display does not illuminate:
• Press Power/Fire button.
• Check and, if necessary, replace the battery. If the unit does not respond to button presses, replace the battery with
a good quality CR2 3-volt Lithium battery.
If unit powers down (display goes blank when attempting to power the laser):
• The battery is either weak or low quality. Replace the battery with a new 3 -volt lithium battery (CR2).
If the target range cannot be obtained:
• Make sure the display is illuminated.
• Make sure that the Power/Fire button is being pressed.
• Ensure that nothing, such as your hand or finger, is blocking the objective lenses (lenses closest to the target) that
emit and receive the laser pulses.
• Ensure the unit is held steady while pressing the Power/Fire button.
NOTE: The last range reading does not need to be cleared before ranging another target. Aim at the new target using the display reticle, press the
Power/Fire button, and hold until new range reading is displayed.
CLEANING AND GENERAL CARE
Your Bushnell Pro X3 laser rangender lenses are fully multi-coated for the highest light transmission. However, care must
be taken in cleaning the lenses. Follow these tips for proper lens cleaning:
• Blow away any dust or debris on the lens (or use a soft lens brush).
• To remove dirt or fingerprints, clean with the supplied microfiber cloth rubbing in a circular motion. A coarse cloth
or unnecessary rubbing may scratch the lens surface and cause permanent damage. The included washable microfiber
cleaning cloth is ideal for routine optics cleaning. First, breathe lightly on the lens to provide slight moisture, then
gently rub the lens with the microfiber cloth.
• For a more thorough cleaning, photographic lens tissue and photographic-type lens cleaning fluid or isopropyl alcohol
may be used. Always apply the fluid to the cleaning cloth – never directly on the lens.
• The rangefinder is water-resistant but should not be exposed to heavy rain or other direct streams of water and will
not withstand submersion in water or other liquids.
CAUTION: Use caution to avoid direct sunlight into the eyepiece to prevent damage to the display/internal components. When using the BITE magnet to
attach the device to a cart bar or frame, tilt the device so the eyepiece aims towards the ground, not toward the sun. When you are not using the device,
please store it in the case for additional protection.
BITE MAGNETIC MOUNT
The Pro X3 features a powerful BITE magnet incorporated into the right side of its housing, which allows the device to be
securely attached to a golf cart bar or frame.
WARNING: BITE FEATURE INCLUDED WITH THE DEVICE CONTAINS A NEODYMIUM MAGNET. MAGNETS COULD
AFFECT THE FUNCTIONING OF PACEMAKERS AND IMPLANTED HEART DEFIBRILLATORS. IF YOU USE THESE DEVICES,
KEEP A SUFFICIENT DISTANCE FROM THE MAGNET. ALSO, WARN OTHERS WHO WEAR THESE DEVICES FROM
GETTING TOO CLOSE TO MAGNETS.
• The magnet may permanently lose part of its adhesive force if exposed to
temperatures above 175º F (80º C).
• Magnets produce a far-reaching, strong magnetic field. They could damage
TVs and laptops, computer hard drives, credit and ATM cards, data storage media,
mechanical watches, hearing aids, and speakers. Keep the unit away from
devices and objects that strong magnetic fields could damage.
• Magnets have strong magnetic fields which can pinch skin and fingers. Use caution
when attaching the unit to a metal bar.

9
Click to Return to the Table of Contents
BITE Magnetic Mount: The integrated BITE magnet on the
back of your Pro X3 allows you to easily mount your device
to the cart bar.
Dual Display Technology: Technology that allows the user to
switch between using the Red or the Black display at the
user’s discretion.
Elements Compensation: Compensated distances are
adjusted with Elements Compensation. Temperature and
adjusted altitude are added to Slope technology to provide
more precise compensated distances.
IPX7: International waterproof rating. Bushnell Golf Pro X3
is IPX7 rated.
JOLT Technology: A vibrating confirmation setting,
integrated into Bushnell golf rangefinders. Short bursts of
vibrations in the unit are enacted when the rangefinder has
successfully acquired and locked onto the flag.
Locking Slope Switch: Bushnell's Locking Slope Switch is on
the top of the Pro X3, above the lens. The Locking Slope
Switch gives the golfer more assurance that Slope is off
while in a tournament when Slope is not allowed.
PinSeeker with JOLT Technology: JOLT has advanced to
Visual JOLT. A red ring flashes in the display as JOLT gives
the player even greater feedback and confidence to know
the rangefinder has locked onto the flag.
GLOSSARY
TECHNICAL SPECIFICATIONS
Dimensions 4.75 x 1.7 x 3.25 inches
Weight 12 oz.
Ranging Accuracy Accurate to +/- 1 yard
Range 5–1300 Yards / 5–1189 Meters
Magnication 7x
Objective Diameter 28 mm
Display Dual Red & Black LCD w/illuminated JOLT indicator ring
Power Source 3-volt lithium (CR-2)
Field Of View 330 ft. @ 1000 yards / 110 meters @ 1000 meters
Extra Long Eye Relief 15 mm
Exit Pupil 3.7 mm
Included Items Premium Carrying Case and CR2 Battery
Slope Off
Slope On
Slope Compensation: Slope technology calculates the angle
and the compensated range to provide an adjusted distance
because of elevation changes. Its purpose is to ensure you
are properly informed of the distance ahead so you can
select the right club to get the proper trajectory to make it
to the hole.
Slope Switch: Slope is enabled by
sliding the Slope Switch on the
top of the Pro X3. When Slope is
enabled, the Slope Switch is pulled
back and showing an orange strip.
Straight Line Distance: This is the distance from you, or
rather the device, to the target you’re seeking a distance
from. It’s the primary form of distance that’s acquired with
all tournament legal laser and GPS golf rangefinders.
USGA Rule 14-3: You’ll see this term a lot while in the
market for golf rangefinders. It stands for United States
Golf Association. To be able to legally use rangefinders in
tournaments, the device must comply with the USGA’s
measuring device policy found in Rule 14-3. All Bushnell
Golf laser rangerfinders are legal for tournament play when
SLOPE mode is disabled
Vivid Display Technology: Bushnell premium rangefinder
technology where light transmission, contrast, and clarity
are all better than before. The readouts are brighter, and
the display can be read in any light condition.

10
Click to Return to the Table of Contents
Disposal of Electric and Electronic Equipment
(Applicable in the EU and other European countries
with separate collection systems)
This equipment contains electric and/or electronic parts and must
therefore not be disposed of as normal household waste. Instead, it
should be disposed at the respective collection points for recycling
provided by the communities. For you, this is free of charge.
If the equipment contains exchangeable (rechargeable) batteries,
these too must be removed before and, if necessary, in turn be
disposed of according to the relevant regulations (see also the respective comments
in this unit’s instructions).
Further information about the subject is available at your community administration,
your local waste collection company, or in the store where you purchased this
equipment.
FDA SAFETY
Complies with 21CFR1040.10 and 1040.11 except for conformance with IEC60825-1
Ed.3., as described in Laser Notice 56, dated May 8, 2019.
Caution: There are no user controls, adjustments or procedures. Performance of
procedures other than those specified herein may result in access to invisible laser
light.
• This product contains no user serviceable controls.
• This product must not be opened or modified by
the consumer.
• This product must be returned to the
manufacturer for service.
Device specifications and design are subject to
change without notice or obligation on the part of
the manufacturer.
Industry Canada Statement/Déclaration d'Industrie Canada:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Radiation Exposure Statement / Déclaration d’exposition aux radiations:
This device complies with the Industry Canada portable RF exposure limit set forth
for an uncontrolled environment and is safe for the intended operation as described
in this manual. Further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user’s body or if the device is set to a lower output
power if such function is available.
Le produit est conforme aux limites d’exposition pour les appareils portables RF pour
les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction
aux expositions RF peut être augmentée si l’appareil peut être conservé aussi loin que
possible du corps de l’utilisateur ou que le dispositif est réglé sur la puissance de
sortie la plus faible si une telle fonction est disponible.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
The device does not contain any user-serviceable parts. Repairs should only be made
by an Authorized Bushnell Repair center. Unauthorized repairs or modifications could
result in permanent damage to the equipment, and will void warranty and your
authority to operate the device under Part 15 regulations.
Specifications and design are subject to change without any notice or obligation on
the part of the manufacturer.
©2023 Bushnell Outdoor Products
Bushnell,™, ®, denote trademarks of Bushnell Outdoor Products
www.bushnell.com
9200 Cody, Overland Park, KS 66214
Made in China
https://vistaoutdoor.com/patents
WARNING: AS WITH ANY LASER DEVICE, IT IS NOT RECCOMENDED TO
DIRECTLY VIEW THE EMISSIONS FOR LONG PERIODS OF TIME WITH A
MAGNIFIED LENS.
CLASS 1 LASER PRODUCT
EN/IEC 60825-1 2014
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Warning: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
R-R-x6S-20225 214-111986
80950/SDPPI/2022
13902 CMIIT ID 2021DJ8043
FCC ID: 2ASQI-202250
IC: 24886-202250