BVA Hydraulics P1201 User manual

Printed in Taiwan
Models P2301 & P4301
Models P1201 & P1201S
Model P2301M
MODELS: P1201, P1201S, P2301, P2301M & P4301
Hand Pumps
Instruction Manual
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone] * Fax: [phone]
E-mail: [email protected] Website: www.bvahydraulics.com
Maximum Operating Pressure 10,000 PSI
P1201-M0 rev 08/07
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!

Figure 1 - Model P1201 & P1201S Components
2
Figure 2 - Models P2301 & P4301 Components
Handle
Release Valve
Reservoir
Shipping/ Vent Plug
Release Valve
Reservoir
Vent Screw
Handle
Oil Outlet Port
[ 3/8” -18NPTF ]
Carrying
Handle
Carrying
Handle
Oil Outlet Port
[ 3/8” -18NPTF ]
Reservoir
Vent Screw
Handle
Carrying
Handle Oil Ports
[ 3/8” -18NPTF ]
4-way
Control Valve
Control Valve Lever
Figure 3 - Model P2301M Components
Save these instructions. For your safety, read and understand the information contained within. The owner and operator shall
have an understanding of this product and safe operating procedures before attempting to use this product. Instructions and
safety information shall be conveyed in operator’s native language before use of this product is authorized. Make certain that the
operator thoroughly understands the inherent dangers associated with the use and misuse of the product. If any doubt exists as
to the safe and proper use of this product as outlined in this factory authorized manual, remove from service immediately.
Inspect before each use. It is recommended that, prior to each use, an inspection be done by qualified personnel and that any
missing or damaged parts, decals, warning/safety labels or signs be replaced with factory authorized replacement parts only. Any
pump that appears to be damaged in any way, is worn, leaking or operates abnormally shall be removed from service immediately
until such time as repairs can be made. Owners and operators of this equipment shall be aware that the use and subsequent
repair of this equipment may require special training and knowledge.
PRODUCT DESCRIPTION
BVA Hydraulic Hand Pumps are engineered to meet most industrial standards for performance and safety. Models P1201, P2301,
P2301M and P4301 have a unique two- stage hydraulic circuit which allows quick displacement of hydraulic fluid under no load
conditions and easy pumping in loaded conditions. These lever operated pumps supply compressed hydraulic fluid to compatible
applications i.e. rams, presses, spreaders, compactors and crimping machines, anywhere that 10,000 PSI of fluid pressure is
needed. Special skill, knowledge and training may be required for a specific task and the product may not be suitable for all the
jobs described above. Unsuitable applications would include applications that call for a device to move, level or support persons,
animals, hazardous materials, mobile homes/ dwellings in general, mirrors and/or plate glass, and/or to connect/secure hatches,
components, etc. between bulkheads. The user must ultimately make the decision regarding suitability of the product for any
given task and assume the responsibility of safety for himself/ herself and others in the work area.
Always check connections before using. Alteration of these products is strictly prohibited. Use only those adapters and
attachments provided and approved by the manufacturer.
WARNING: To reduce the risk of personal injury and/or property damage, ensure that the rated working pressure of each
pressurized attachment be equal to or greater than the rated working pressure developed by the hydraulic pump
!
!

Model Usable
Oil
Capacity
(in3)
Oil
Capacity
(in3)
Pump
Type
Pressure
Rating
(psi)
Oil Displace-
ment per Stoke
(in3)
Operating
Force
(lb)
Mounting
Plate
Holes
Distance
(in)
Pump Size
(L) x (W) x (H)
Net
Weight
(lb)
1st
stage
2nd
stage
1st
stage
2nd
stage
P1201S
67 73
Single-
speed
10,000
0.13
132
3.74 22 1/4” x 5 3/8” x 6 1/2” 20.0
P1201
Two-
speed 200 0.81 0.14
3.74 22 1/4” x 5 3/8” x 6 3/4” 20.3
P2301
128 140
3.54 24” x 5 3/8” x 6 3/4” 27.5
P2301M 3.54 27 1/2” x 4 3/4” x 6 1/2” 32.2
P4301 250 262 3.74 22 7/8” x 6 1/4” x 7 1/2” 37.4
SPECIFICATIONS
3
• Study, understand, and follow all
instructions provided with and on this
device before use.
• All WARNING statements must be
carefully observed to help prevent
personal injury.
• No alteration shall be made to this
device.
• Always wear protective gear when
operating hydraulic equipment.
• Keep hydraulic equipment away from
flames and heat. Hydraulic fluid can
ignite and burn. Do not operate if
leaks are detected.
• Crush Hazard. Keep hands and feet
away from loading area. Avoid pinch
points or crush points that can be
created by the load, cylinder, or any
equipment of system.
• To avoid crushing and related injuries:
NEVER work on, under or around
a lifted load before it is properly
supported by appropriate mechanical
means. Never rely on hydraulic
pressure alone to support load.
! WARNING
HYDRAULIC PUMPS
• The user must be a qualified operator familiar with the
correct operation, maintenance, and use of pumps. Lack of
knowledge in any of these areas can lead to personal injury.
• Do not exceed rated capacity of the pump or any equipment
in the system.
• Never attempt to lift a load weighing more than the capacity
of the cylinder.
• Do not subject the pump and its components to shock
loads.
• Burst hazard exists if hose or connection pressure exceeds
rated pressure.
• Inspect pump, cylinder, hoses and connections before each
use to prevent unsafe conditions from developing. Do not
use if they are damaged, altered or in poor condition. Do
not operate the system with bent or damaged coupler or
damaged threads.
• Never hold or stand directly in line with any hydraulic
connections while pressurizing.
• Use gauge or other load measuring instrument to verify load.
• Never attempt to disconnect hydraulic connections under
pressure. Release all line pressure before disconnecting
hoses.
• Use only approved accessories and approved hydraulic fluid.
• Never attach ANY component not authorized by manufacturer.
• Always ensure that the chosen application is stable to work
on and around.
• Do not connect to application which can return more oil to
the reservoir than the pump reservoir can hold.
• Do not connect pump to hydraulic system powered by
another pump.
• This device is not suitable for use as support device! As
the system load is lifted, use blocking and cribbing to guard
against a falling load.
• All personnel must be clear before lowering load or
depressurizing the system.
• Never try to disassemble a hydraulic cylinder, refer repairs
to qualified, authorized personnel.
HYDRAULIC HOSES & FLUID TRANSMISSION LINES
• Avoid short runs of straight line tubing. Straight line runs
do not provide for expansion and contraction due to
pressure and/or temperature changes.
• Reduce stress in tube lines. Long tubing runs should be
supported by brackets or clips. Before operating the pump,
tighten all hose connections with proper tools. Do not
overtighten. Connections should only be tightened securely
and leak-free. Overtightening can cause premature thread
failure or high pressure fittings to burst.
• Should a hydraulic hose ever rupture, burst or need to be
disconnected, immediately shut off the pump and release
all pressure. Never attempt to grasp a leaking pressurized
hose with your hands. The force of escaping hydraulic fluid
can inflict injury.
• Do not subject the hose to potential hazard such as fire,
sharp objects, extreme heat or cold, or heavy impact.
• Do not allow the hose to kink, twist, curl, crush, cut or bend
so tightly that the fluid flow within the hose is blocked or
reduced. Periodically inspect the hose for wear.
• Do not pull, position or move setup by the hose.
• Hose material and coupler seals must be compatible with
hydraulic fluid used. Hoses also must not come in contact
with corrosive materials such as battery acid, creosote-
impregnated objects and wet paint. Never paint a coupler
or hose.
• FAILURE TO HEED THESE WARNINGS MAY RESULT IN
PERSONAL INJURY AS WELL AS PROPERTY DAMAGE.

BEFORE USE
1. Before using this product, read the instruction manual
completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards
associated with its use.
2. Verify that the product and the application are compatible.
Inspect before each use. Do not use if bent, broken, leaking
or damaged components are noted.
3. Replace worn or damaged parts and assemblies with
BVA Hydraulics Authorized Replacement Parts only (See
Replacement Parts Section). Lubricate as instructed in
Maintenance Section.
4.Ensure method of confirming load is accurate and working
properly. Have gauge or load cell accuracy verified by
qualified personnel on a yearly basis.
5.Pumps should be stored where protected from the elements,
abrasive dust, and damage. Pumps can be stored
horizontally or vertically.
SET UP
IMPORTANT: The pump’s maximum working pressure is
10,000 PSI. Make sure that all hydraulic equipment such as
cylinders, hoses, couplers and etc. used with this pump are
rated at 10,000 PSI operating pressure or more.
1. Prepare the pump for use:
A) For models P1201 & P1201S:
Remove shipping plug and replace with a vent plug. Pull
vent plug stem upward before use, press down when
moving or storing the pump. (refer to Figure 4)
B) For models P2301, P2301M & P4301:
Turn the top cap of the vent screw counter-clockwise to
open the vent. Turn the cap clockwise to close the vent
screw when moving or storage. (refer to Figure 5)
2. Carefully remove the threaded plug on oil outlet port, then
connect 3/8”NPTF hydraulic connection to oil outlet port,
i.e. coupler, hydraulic hose, fitting etc.
For model P2301M: The pump comes with a 4-way valve
to use with double acting cylinder. Connect two hoses from
the pump to both ports of a double-acting cylinder.
If using on single acting cylinder, the valve needs to be
changed to 3-way valve. Consult with BVA Technical service
888-332-6419.
Note: Always secure threaded connections with non-hardening
pipe thread compound. Take care not to introduce compound
into port orifices. Tighten securely to prevent accidental
removal of components while in use.
3. Install a pressure gauge in-line from the pump for better
control and safety purpose.
4. Tighten securely to prevent accidental removal of
components while in use.
5. Check for leaks in system and repair by qualified personnel
as needed. Depressurize the hydraulic system before
servicing.
4
Figure 5 - Prepare to use Illustration for P2301,
P2301M & P4301
Remove shipping plug and replace with air vent
plug (included) before initial use.
Pull stem upward before use, press down when
moving or storing pump.
Figure 4 - Prepare to use Illustration for P1201 & P1201S
Turn the top cap counter-clockwise to open the
vent before use.

OPERATION
ALWAYS monitor pressure, load or position using
suitable equipment. Pressure may be monitored by means of
an optional manifold and gauge (contact BVA Hydraulics).
Load may be monitored by means of a load cell and digital
indicator. Correct application position can only be determined
by the operator of the equipment.
1. Remove the threaded plug, then connect the pump to
suitable application.
2. Ensure the oil level is correct and the system fittings and
connections are leak free before operating the pump.
3. Pump may be used in horizontal and vertical position
as illustrated on Figure 6.
5
Position 1: Pressurized
oil flows to port A, port B
returns flow to reservoir
Position 3: Pressurized
oil flows to port B, port A
returns flow to reservoir.
Position 2: Neutral,
ports A and B are
closed. Hold Position.
Port A Port B Port A Port B Port A Port B
P R P R P R
(a) 4-way, 3-position valve for Double Acting Cylinder
Position 1 (Advance):
Pressurized oil flows to
port A.
Position 3 (Retract):
Port A returns flow to
reservoir.
Position 2 (Hold):
Neutral, port A is closed.
Hold Position.
Port A Port A Port A
(b) 3-way, 3-position valve for Single Acting Cylinder
Port A Port B
1
2
3
P R P R P R
Figure 7 - Flowpath of the valve positions and operations for Model P2301M.
Figure 6 - Horizontal and Vertical Position
For models P1201, P1201S, P2301 & P4301:
A. Close release valve by turning it clockwise. Finger tight
ONLY. Using tools on release valve can damage it and
cause the pump to malfunction.
B. Pump handle until desired pressure, load or position is
reached.
C. Pressure will maintain until the release valve is opened.
D. To retract application, turn the release valve knob slowly
counterclockwise (never more than 2 full turns).
NEVER operate pump with release valve closed and
disconnected from application. If operated in this condition,
the hose and connections become pressurized. This
increases burst hazard. Damage may occur to pump and
its components.
For model P2301M:
Use the control valve lever to control the direction of hydraulic
oil flow, refer to Figure 7(a) below. Pump handle until desired
pressure, load or position is reached.
! WARNING: Operate double-acting cylinder only when
both hoses are connected to the pump. If one coupler is left
unconnected, high pressure will build behind the coupler
which could cause personal injury and/or equipment
damage.
Note: To use with 3-way setting shown in Figure 7(b) for
application such as single acting cylinder, please have an
authorized service center changes the valve to 3-way valve.
Consult BVA Hydraulics Technical Service 888-332-6419.
!
!
!

MAINTENANCE
1. Inspect hoses and connections daily. Replace damaged
components immediately with BVA Hydraulics
Replacement Parts only.
2. Tighten connections as needed. Use pipe thread sealing
compound when servicing connections.
3. Use only good quality hydraulic fluid. We recommend
Mobil DTE 13M or equivalent. Never use brake fluid,
transmission fluid, turbine oil, motor oil, alcohol,
glycerin etc. Use of other than good quality hydraulic
oil will void warranty and damage the pump, hose, and
application.
Adding Hydraulic Fluid
1. Depressurize and disconnect hydraulic hose from
application.
2. With pump in its upright, horizontal position, remove
vented oil filler plug/screw located on top of the
reservoir.
3. Use a small funnel to fill reservoir to within 1/4” (6mm)
of the opening.
4. Wipe up any spilled fluid and reinstall the vented oil filler
plug/screw.
6
Changing Hydraulic Fluid
For best results, change fluid once a year.
1. Remove vented filler plug/screw and drain used fluid into
a sealable container.
2. Dispose of fluid in accordance with local regulations.
3. Fill with a good quality hydraulic oil as recommended
above. Reinstall vented oil filler plug/screw.
Lubrication
Use a light machine oil to lubricate pivot points, hinges
etc.
Storage
1. When not in use, depressurize and disconnect hoses
from application.
2. Wipe clean thoroughly
3. Store in clean, dry environment. Avoid temperature
extremes.
4. Shield pump with a protective cover.
TROUBLESHOOTING GUIDE
The following information is intended as an aid in determining if problem exists. Pumps should be repaired only by authorized
BVA Service Center. For repair service, contact service center in your area.
Symptom Possible Causes Corrective Action
Erratic application action • Air in the system.
• External leak.
• Internal hydraulic leak.
• Vent the system.
• Tighten all connections.
• Contact service center.
Application does not extend,
move or respond to pressurized
fluid
• Overload condition.
• Release valve not closed.
• Loose couplers/connections.
• Faulty couplers/connections.
• Pump malfunction.
• Remedy overload condition.
• Ensure release valve closed.
• Tighten couplers/connections.
• Replace couplers/connections.
• Contact service center.
Application responds to
pressurized fluid, but system does
not maintain
pressure
• Overload condition.
• Release valve not closed.
• Pump or valve malfunction.
• Application/connection leaking.
• Remedy overload condition.
• Ensure release valve closed.
• Contact Service Center.
• Replace application/connection.
Application responds slower than
normal
• Loose connection or coupler.
• Restricted hydraulic line or fitting.
• Application/connection leaking.
• Tighten connection or coupler.
• Clean and replace if damaged.
• Replace application/connection.
Application does not return fluid to
pump (i.e. cylinder will not retract)
• Malfunctioning coupler, damaged
application.
• Reservoir overfilled
• Secure load by other means. Open
release valve, depressurize pump and
hose, remove coupler and/or application,
then renew or replace.
• Secure load by other means. Open
release valve, depressurize pump and
hose, remove application, then drain
fluid to proper level.
Poor performance • Fluid level in pump is low. • Ensure proper fluid level.

LIMITED LIFETIME WARRANTY
BVA Hydraulics®, represented in the United States by SFA Companies [“SFA”] warrants this product to be free from defects in
material and workmanship for the life of the product as long as the original purchaser owns the product. The warranty is non-
transferable and is subject to the terms, exclusions, and limitations described below:
• Damaged components, including but not limited to bent rams, dented or crushed cylinder walls, broken welds or couplers as
well as worn out seals, o-rings and springs are the result of misuse and not covered by warranty and BVA Hydraulics will not
provide any warranty credit for such damaged components.
• This warranty does not cover ordinary wear and tear, overloading, alterations (including repairs or attempted repairs not
performed by BVA Hydraulics or one of its authorized personnel), improper fluid use, or use of the product in any manner for
which the product was not intended or the use of which is not in accordance with the instructions or warnings provided with
the product.
• In the unlikely event that a BVA Hydraulics product fails due to material defect in workmanship, you may contact SFA for
disposition. In such cases, the customer’s sole and exclusive remedy for any breach or alleged breach of warranty is limited
to the repair or replacement of the defective product.
• Under no circumstances is BVA Hydraulics liable for any consequential or incidental damage or loss whatsoever.
• THIS WARRANTY IS LIMITED TO NEW PRODUCTS SOLD THROUGH AUTHORIZED DISTRIBUTORS AND OTHER
CHANNELS DESIGNATED BY BVA HYDRAULICS. NO AGENT, EMPLOYEE OR OTHER REPRESENTATIVE OF BVA
HYDRAULICS IS AUTHORIZED TO MODIFY THIS WARRANTY.
• THE FOREGOING IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FOR A FITNESS FOR A PARTICULAR
PURPOSE.
• Components not manufactured by BVA Hydraulics including certain motor systems, gasoline engines, and others are not
covered by this warranty and instead are covered by the manufacturer’s separate manufacturer’s warranty provided in the
package.
• BVA Hydraulics’ liability in all cases is limited to, and will not exceed the purchase price paid for the product.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone]
E-mail: [email protected]
7

Parts Illustration (refer page 11 for part number)
Note: Not all components of the pump are replacement items, but are illustrated as a
convenient reference of location and position in the assembly sequence.
P1201-M0
rev 08/07
MODEL: P1201S
Hand Pump
Service Parts
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone] * Fax: [phone]
E-mail: [email protected] Website: www.bvahydraulics.com
8
Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized
Replacement Parts only.

Parts List (Model P1201S)
9
Item Part Number Description Qty
1 677-5-0040-102 E-clip 2
2 H18-5-1318-104 Pin 1
3 H18-6-1318-100 Pin 1
4 H18-6-1602-201 Pin, Piston 1
5 667-5-0100-005 C-clip 1
6 H28-6-1814-100 Piston 1
7 H28-6-1815-102 Piston Seat 1
8 * Back-up Ring 1
9 * U-cup 1
10 * O-ring 1
11 H28-6-1813-108 Pump Cylinder 1
12 * Back-up Ring 1
13 * O-ring 1
14 D05-6-1001-106 Nut 1
15 A17-6-1216-102 Needle Valve 1
16 512-2-0067-010 Compressing Spring 1
17 A17-5-1603-300 Adjust Nut 1
18 * Special Washer 1
19 414-6-1215-509 Nut 1
20 601-7-0008-009 Steel ball 2
21 H28-4-1700-105 Release Valve Assy. 1
22 N/A Base 1
23 651-7-0063-007 Adapter 1
24 H53-6-1808-104 Tube 1
25 532-8-0040-012 Filter 1
26 H28-6-4401-102 Steel Rod 1
27 * O-ring 2
28 641-1-0098-103 Screw 1
29 512-2-0063-104 Compressing Spring 1
30 601-7-0012-000 Steel Ball 1
31 552-2-0080-106 Bevel Compressing Spring 1
32 * Special Washer 2
33 H18-6-1215-100 Nut 1
34 H18-4-2102-100 Handle w/ Grip 1
35 H18-6-2112-105 Handle Grip 1
36 505-9-0092-207 Shipping Plug 1
37 H18-4-4000-102 Vent Plug 1
38 H28-3-1803-208 Reservoir
39 H28-6-1501-101 End Cap 1
40 671-2-0100-205 Nut 1
(*) H28-3-9902-109 Seal Kit 1
(*) - indicates items included in, and available only as part of Seal Kit
N/A - part is not available as replacement

Parts Illustration (refer page 11 for part number)
Note: Not all components of the pump are replacement items, but are illustrated as a
convenient reference of location and position in the assembly sequence.
P1201-M0
rev 08/07
MODEL: P1201
Hand Pump
Service Parts
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone] * Fax: [phone]
E-mail: [email protected] Website: www.bvahydraulics.com
10
Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized
Replacement Parts only.

11
Item Part Number Description Qty
1 677-5-0040-102 E-clip 2
2 H18-5-1318-104 Pin 1
3 H18-6-1318-100 Pin 1
4 H18-6-1602-201 Pin 1
5 667-5-0100-005 C-clip 1
6 H18-3-1306-105 Piston Assy. 1
7 * O-ring 1
8 * Back-up Ring 1
9 * Back-up Ring 1
10 * O-ring 1
11 D05-6-1001-106 Nut 1
12 A17-6-1216-102 Needle Valve 2
13 512-2-0082-117 Compressing Spring 1
14 A17-5-1603-300 Adjust Nut 2
15 * Special Washer 2
16 414-6-1215-509 Nut 2
17 512-2-0067-010 Compressing Spring 1
18 601-7-0008-009 Steel Ball 3
19 H28-4-1700-105 Release Valve Assy. 1
20 N/A Base 1
21 651-7-0063-007 Adapter 1
22 H53-6-1808-104 Tube 1
23 532-8-0040-012 Filter 1
24 H28-6-4401-102 Steel Rod 1
25 * O-ring 2
26 641-1-0098-103 Screw 1
27 512-2-0063-104 Compression Spring 2
28 601-7-0012-000 Steel ball 2
29 552-2-0080-106 Bevel Spring 2
30 * Washer 3
31 H18-6-1215-100 Nut 2
32 H18-4-2102-100 Handle w/ Grip 1
33 H18-6-2112-105 Handle Grip 1
34 505-9-0092-207 Shipping Plug 1
35 H18-4-4000-102 Vent Plug 1
36 H28-3-1803-208 Reservoir 1
37 H28-6-1501-101 End Cap 1
38 671-2-0100-205 Nut 1
(*) H28-3-9900-107 Seal Kit -
Parts List (Model P1201)
(*) - indicates items included in, and available only as part of Seal Kit
N/A - part is not available as replacement

12
Parts Illustration (refer page 13 for part number)
Note: Not all components of the pump are replacement items, but are illustrated as a
convenient reference of location and position in the assembly sequence.
P1201-M0
rev 08/07
MODELS: P2301 & P4301
Hand Pumps
Service Parts
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone] * Fax: [phone]
E-mail: [email protected] Website: www.bvahydraulics.com
12
Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized
Replacement Parts only.

13
Parts List (Models P2301 & P4301)
(*) - indicates items included in, and available only as part of Seal Kit
N/A - part is not available as replacement
Item Part Number for Model: Description Qty
P2301 P4301
1 677-5-0040-102 E-clip 2
2 H18-5-1318-104 Pin 1
3 H18-6-1318-100 Pin 1
4 H18-6-1602-201 Pin 1
5 667-5-0100-005 C-clip 1
6 H18-3-1306-105 Piston Assy. 1
7 * O-ring 1
8 * Back-up Ring 1
9 * Back-up Ring 1
10 * O-ring 1
11 D05-6-1001-106 Nut 1
12 A17-6-1216-102 Needle Valve 2
13 512-2-0082-117 Compressing Spring 1
14 A17-5-1603-300 Adjust Nut 2
15 * Special Washer 2
16 414-6-1215-509 Nut 2
17 512-2-0067-010 Compressing Spring 1
18 601-7-0008-009 Steel Ball 3
19 H28-4-1700-105 Release Valve 1
20 H28-6-1601-002 Base 1
21 651-7-0063-007 Adapter 1
22 H53-6-1808-104 Tube 1
23 532-8-0040-012 Filter 1
24 H28-5-4401-106 H28-6-4401-102 Steel Rod 1
25 * O-ring 1
26 641-1-0098-103 Screw 1
27 512-2-0063-104 Compressing Spring 2
28 601-7-0012-000 Steel ball 2
29 552-2-0080-106 Bevel Compressing Spring 2
30 * Special washer 3
31 H18-6-1215-100 Nut 2
32 H18-4-2102-100 H28-4-1705-100 Handle w/ Grip 1
33 H18-6-2112-105 Handle Grip 1
34 H28-4-1809-105 Air vent Screw 1
35 H28-3-1804-200 H28-3-1802-105 Reservoir 1
36 671-2-0100-205 Nut 1
(*) H28-3-9901-109 Seal Kit 1

14
Parts Illustration (refer page 15 for part number)
Note: Not all components of the pump are replacement items, but are illustrated as a
convenient reference of location and position in the assembly sequence.
P1201-M0
rev 08/07
MODEL: P2301M
Hand Pump
Service Parts
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone] * Fax: [phone]
E-mail: [email protected] Website: www.bvahydraulics.com
Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized
Replacement Parts only.

15
Parts List (Model P2301M)
(*) - indicates items included in, and available only as part of Seal Kit
N/A - part is not available as replacement
Item Part Number Description Qty
1 E05-6-1008-109 Knob 1
2 A67-6-1012-106 Handle Bar 1
3 649-1-0050-055 Screw 1
4 A67-6-1005-109 Control Valve Cover 1
5 601-7-0006-005 Steel Ball 2
6 512-2-0046-104 Compression Spring 2
7 644-1-0060-071 Socket Bolt 1
8 649-1-0080-003 Socket Bolt 4
9 A67-6-1009-107 Control Valve Base 1
10 A67-6-1006-101 Washer 2
11 623-6-2542-104 Bearing 1
12 * O-ring 2
13 A67-6-1003-903 Control Valve 1
14 * O-ring 1
15 A67-6-1001-202 Oil Outlet Valve 3
16 606-3-0008-101 Spring Washer 3
17 * Back-up Ring 3
18 * O-ring 3
19 601-4-0030-095 Pin 1
20 D05-6-1001-106 Nut 2
21 649-1-0060-205 Screw 3
22 H53-6-1812-105 Valve Base 1
23 601-7-0008-009 Steel Ball 3
24 644-1-0080-031 Screw 1
25 * O-ring 4
26 * Back-up Ring 4
27 H53-6-1810-101 Oil Outlet Tube 2
28 A17-6-1216-102 Needle Valve 2
29 512-2-0082-117 Compression Spring 1
30 A17-5-1603-300 Adjust Nut 2
Item Part Number Description Qty
31 * Special Washer 2
32 414-6-1215-509 Nut 2
33 512-2-0067-010 Compression Spring 1
34 H28-6-1811-003 Base 1
35 651-7-0063-007 Adapter 1
36 H53-6-1808-104 Tube 1
37 532-8-0040-012 Filter 1
38 H28-5-4401-106 Steel Rod 1
39 * O-ring 1
40 641-1-0098-103 Screw 1
41 512-2-0063-104 Compression Spring 2
42 601-7-0012-000 Steel Ball 2
43 552-2-0080-106 Bevel Compression
Spring
2
44 * Special Washer 3
45 H18-6-1215-100 Nut 2
46 * O-ring 1
47 * Back-up Ring 1
48 * Back-up Ring 1
49 * O-ring 1
50 H18-3-1306-105 Piston Assy. 1
51 667-5-0100-005 C-clip 1
52 677-5-0040-102 E-clip 2
53 H18-5-1318-104 Pin 1
54 H18-6-1318-100 Pin 1
55 H18-6-1602-201 Pin 1
56 H18-3-2102-104 Handle w/ Grip 1
57 H18-6-2112-105 Handle Grip 1
58 H28-4-1809-105 Air vent Screw 1
59 H28-3-1804-200 Reservoir 1
60 671-2-0100-205 Nut 1
(*) H28-3-9904-103 Seal Kit -

SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: [phone]
E-mail: [email protected]