manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. C.A.T.
  6. •
  7. Paint Sprayer
  8. •
  9. C.A.T. AutoCAT 100H User manual

C.A.T. AutoCAT 100H User manual

HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
NO. AIR CAPS Press /
Siphon
*MAX GUN
INLET PRESS.
FOR HVLP
FAN
CONTROL
ORIFICE
SCFM @
MAX GUN
INLET
AIR CAP
RING
AVAI LABLE F LUI D
NOZZLES TIPS
NEEDLES /
marking on needle
21-1090 pressure 15 6 31-0205 0.5mm (.020")
21-1091 pressure 15 8 31-0208 0.8mm (.022")
21-1092 pressure 15 8 31-0210 1.0mm (.040")
21-1093 pressure 18 10 31-0212 1.2mm (.046")
21-1094 pressure 33 13 31-0213 1.3mm (.052")
21-1095 pressure 50 22.5 31-0214 1.4mm (.055")
21-1097 pressure 50 22.5 31-0215 1.5mm (.059")
21-1195 pressure 50 22.5 31-0216 1.6mm (.063")
21-1197 pressure 50 22.5 31-0217 1.7mm (.070")
31-0412 1.2Fmm (.046") 40-A112F (112F)
31-0414 1.4Fmm (.055") 40-A114F (114F)
31-0417 1.7Fmm (.070") 40-A117F (117F)
*Note: Air cap test gages are available to confirm HVLP compliance.
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Gun inlet pressures may vary as required by application
40-A100 (100)
A100H
60-616
21-1001
included
AUTOMATIC SPRAY GUN
PRODUCT INFORMATION
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
www.spraycat.com
AA
AA
Autut
utut
utoCoC
oCoC
oCAA
AA
AT 1T 1
T 1T 1
T 100H00H
00H00H
00H
Operation and Maintenance Instructions for
A100HA100H
A100HA100H
A100H
Spray Guns
Gun Mounting
A 1/2” dia. x 5” lg. rod is provided for mounting. The gun can be mounted from the left or right side or from the bottom.
Thread the mounting rod (9) into one of the three holes that best suit the mounting location for the application. Tighten
the locknut (10) to secure the gun in the position desired. Do not plug the remaining holes as they are used as drain
holes in the event of a needle seal leak.
Operation: Connections and Adjustments
The automatic gun requires two separate regulated air supply lines.
1. Connect one air line to the fitting marked “CYL”, this actuates the gun on and off and is usually connected through an
air solenoid.
2. Connect the second air line to the fitting marked “ATM”, this provides atomizing and fan air.
3. Connect a pressurized fluid supply to the gun fluid inlet.
4. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control
fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
5. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.
Maintenance: Needle Seal Replacement
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.
Before beginning needle seal replacement, it is recommended kit no. 10-107 be on hand.
Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.
1. Remove fluid control knob (36), needle return spring (34), and needle assembly (33).
2. Remove end cap (32) and piston return spring (31).
3. Piston (29) can be removed with pliers by carefully gripping the hub on the rear of the piston.
4. Remove the air control spool (22) using an 11/16” socket to unscrew it from the body.
5. The needle seal can be removed using a 7/16” socket with a short extension. Install a new needle seal and torque to
approx. 2 ft.-lbs.
6. It is recommended that the o-rings on the air control spool (22) and piston (29) be replaced and lubricated before
reassembling the gun.
NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.
Gun head disassembly and reassembly instructions:
Have repair kit # 10-107 available before gun disassembly.
Gun head disassembly
To remove the nozzle carrier (6) and air cap adapter (7):
1. Remove the air cap (1 & 2), fluid nozzle tip (3), fluid nozzle body (4), and needle (33).
2. Remove the needle seal cartridge (18) as described above.
3. Loosen the locknut (26) using 11/16” wrench and remove fluid inlet (27) using a 5/8” open-end wrench.
4. The nozzle carrier (6) and air cap adapter (7) will now slide forward from the gun body (11).
Gun head reassembly
1. Install a new o-ring (8) on the air cap adapter (7).
2. Install the thread locknut (26) onto the fluid inlet (27) as far as possible.
3. Install a new fluid inlet seal (25) into the recess area on the nozzle carrier (6) inlet port.
4. Slide the nozzle carrier (6) into air cap adapter (7) and insert into the gun body (11) as far as possible. Be sure the
nozzle carrier (6) extends into the hole at the back of the gun head. Install the needle seal (18) but do not tighten.
5. Rotate the nozzle carrier (6) until the fluid inlet port in the nozzle carrier (6) is aligned with the threaded hole in the
body. While in this position, insert the fluid inlet (27) and tighten firmly.
6. Tighten the needle seal (18) to approx. 12 ft.-lb. torque.
7. Tighten the fluid inlet (27) to approx. 25 ft.-lb. torque.
8. Tighten the locknut (26) to approx. 33 ft.-lb. torque.
*
*
*
*
*
*
*
*
*
*
*
ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION
1 See Air Cap Chart Air Cap Ring** 20 98-8006 O-Ring (Teflon)*
2 See Air Cap Chart Air Cap** 21 98-7006 O-Ring (Viton) 2 Required*
3 See Air Cap Chart Fluid Tip** 22 60-603 Air Control Spool
4 31-1201 Fluid Nozzle Body 23 98-7014 O-Ring (Viton) 2 Required*
60-L11H Nozzle Body Carrier (Standard) 24 98-7027 O-Ring (Viton) 2 Required*
60-A11H-R Nozzle Body Carrier (Recirculating) 25 60-124 Seal*
7 60-12H Air Cap Adapter 26 60-128 Locknut
8 60-131 O-Ring (Teflon)* 27 60-126 Fluid Inlet
9 60-614 Mounting Rod 28 98-8010 O-Ring (Teflon)*
10 98-0115 Locknut (3/8-16) 29 60-602 Piston
11 60-621 AutoCAT Gun Body HVLP 30 98-7217 O-Ring (Viton)*
12 60-136 Plug 31 66-246 Piston Return Spring
13 98-8108 O-Ring (Teflon)* 32 60-601 End Cap
14 98-0108 Circlip 33 See Air Cap Chart Needle Assembly
15 60-605 Fan Control Housing 34 60-613 Needle Return Spring
16 60-606 Fan Control Stem 35 60-612 Locknut - Fluid Control Knob
17 See Air Cap Chart Fan Control Orifice** 36 60-608 Fluid Control Knob
18 60-1400 Needle Seal Assembly* 37 53-551 (Not Show n)*** Cylinder Air Fitting 1/8 NPT x 1/4 NPS
19 60-604 Seal Cap 38 53-552 (Not Show n)*** Atomz. Air Fitting 1/4 NPT x 1/4 NPT
*Indicates part included in repair kit # 10-107
**See air cap selection chart on page 1
***Air inlet f ittings are available in 90 degree elbow . 90 degree elbow tubing "push on" style fittings
P/N 53-520 1/8 NPT x 1/4" OD Tube
P/N 53-521 1/4 NPT x 3/8" OD Tube
Recirculating setups require: Item 6 (recirculating) & items 25, 26, 27 in place of item 12
6
A100H HVLP AUTOMATIC SPRAY GUN
MATERIAL TYPE FLUID ORIFICE x
AI R C AP
MAXIMUM
PATTERN WIDTH PRESS. / SIPHON
Very Thin
less than 16 sec. Zahn #2
inks , dyes,
solvents, stains
Thin
16 to 20 sec. Zahn #2
lacquers, enamels,
primers, sealers
Medium
21 to 30 sec. Zahn #2
automotive base coat
enamels, primers
epoxies, urethanes
automotive clear coat
Heavy
over 30 sec. Zahn #2
heavy body primers
high solid enamels
high solid automotive coatings
adhesives
P
P
1.3, 1.4, 1.5 mm x 1093
1.3, 1.4, 1.5 mm x 1095
1.3, 1.4, 1.5 mm x 1097
12
12
13
P
P
P
1.6, 1.7 mm x 1095
1.6, 1.7 mm x 1097
1.6, 1.7 mm x 1195
1.6, 1.7 mm x 1197
12
13
13
14
P
P
P
P
FLUID NOZZLE / AIR CAP SELECTION CHARTS
AUTOCAT Series 100H - Pressure Feed Guns
0.5, 0.8 mm x 1090
0.5, 0.8 mm x 1092
10
11
P
P
1.0, 1.2 mm x 1092
1.0, 1.2 mm x 1093
11
12
Revised 3/18/14

This manual suits for next models

2

Other C.A.T. Paint Sprayer manuals

C.A.T. AutoCAT 300H User manual

C.A.T.

C.A.T. AutoCAT 300H User manual

C.A.T. jaguar slp series User manual

C.A.T.

C.A.T. jaguar slp series User manual

Popular Paint Sprayer manuals by other brands

VSI 305 LP manual

VSI

VSI 305 LP manual

Fimco LG-13-P owner's manual

Fimco

Fimco LG-13-P owner's manual

Graco EVR instructions

Graco

Graco EVR instructions

Graco PRO 247936 instructions

Graco

Graco PRO 247936 instructions

AFCO AF 940119 Installation & operation instructions

AFCO

AFCO AF 940119 Installation & operation instructions

Kremlin J 53 instruction manual

Kremlin

Kremlin J 53 instruction manual

Nu-Calgon Turbo Tank Sprayer 2.0 Operation instructions

Nu-Calgon

Nu-Calgon Turbo Tank Sprayer 2.0 Operation instructions

NEW BRUNSWICK SCIENTIFIC innOva 4200 Guide to Operation

NEW BRUNSWICK SCIENTIFIC

NEW BRUNSWICK SCIENTIFIC innOva 4200 Guide to Operation

i-team i-cover 2.5 user manual

i-team

i-team i-cover 2.5 user manual

WAGNER AG-19 owner's manual

WAGNER

WAGNER AG-19 owner's manual

Titan 440i owner's manual

Titan

Titan 440i owner's manual

Swagman Sprayer 8ltr Assembly guide

Swagman

Swagman Sprayer 8ltr Assembly guide

WAGNER Super Finish 27 operating manual

WAGNER

WAGNER Super Finish 27 operating manual

Smithco Spray Star 1000 Parts & service manual

Smithco

Smithco Spray Star 1000 Parts & service manual

Daewoo DASP 400 user manual

Daewoo

Daewoo DASP 400 user manual

Ruris A109S manual

Ruris

Ruris A109S manual

Rockwood 8PC HVLP PAINT GUN SET instructions

Rockwood

Rockwood 8PC HVLP PAINT GUN SET instructions

Walther Pilot Rapid operating instructions

Walther

Walther Pilot Rapid operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.