Ca'Bano 6068 User manual

BS03991737
BS03991737
III Installation Diagram:
I. Installation Notice:
1. Install water supply lines in accordance with this manual.
2. Floor drain should be installed on the site.
3. Except the shower holder, all the exposed parts of the product
must be installed only after the completion of house interior
decoration in case paint or other chemicals erode the product
surface. Before that, the protective sheath on the shower holder
can not be taken off.
4. Clean pipes to get rid of mud, sand or other debris in pipes before
installation.
5. Check whether the threads can be matched. Otherwise, install
forcefully will damage the components.
6. After installation, check all the joints to make sure they are firmly
connected. Then keep water flow. Turn on and off repeatedly to
ensure there is no leakage around the joints. After that, the product
is ready for normal use.
7. Hand the manual to the user.
II. Operation Notice:
1. The product is used under water pressure 0.1~0.5MPa, water
temperature 4~70°C.
2. Do not hang heavy things on the product.
3. Remember to turn off the mixer when no water comes out of it,
especially when nobody in the house or during the decoration period or
power off.
4. Clean the surface of the product regularly to keep it bright.
Note: Please do not use inappropriate tools such as sharp brushes,
rough sponges, scouring pads or corrosive detergent. And it is not
recommend to use the detergent sold in the market, because its
formula changes frequently. Please clean the product with wet cloth and
soapy water after some time of usage. Then rinse the soap out with
clean water and dry with a soft cotton cloth.
5. Adjust the temperature before use, then open the cold and hot water in
turn. To avoid scald, do not stand right below the shower head.
6. Do not disassemble the product without help from the professionals.
IV Installation Steps (Fig.1~20)： The installation diagram is only for reference,
the product is subject to the real object.
Prepare below tools
Drill Safety Goggle
Level Bar Phillips Screwdriver
S7 Wrench
(supplied) S2.5 Wrench
(supplied)
Pencil Teflon Tape
#6068
Generation wall mount rain head
INSTALLATION GUIDE
Last revision: October 23rd

Shower Seat
90° Elbow
Wrap teflon tape around
the 90° elbow. Then
screw it into the shower
holder.
Attention:keep two open
ends face downwards.
Inlet Tubes
Connect the inlet tubes
of proper length.
Mounting Plate
Adjust the shower seat
with level bar to keep it in
a horizontal position.
Take the fixation holes on
the mounting plate as
benchmark to make
marks on the wall.
Drill six Ø8 holes at
the marked positions.
Anchors
Self-tapping
Screws
Insert the anchors
into Ø8 holes.
Lightly fix the shower
holder to wall by
self-tapping screws.
Level adjustment
on the top surface
Vertical adjustment
at the front side
Adjust the shower
seat with level bar,
then tighten
self-tapping screws.
Alternatively, slot the
wall first with the
size of shower seat
and mounting plate,
then install the shower
holder into the slot.
Protective
Sheath
Turn on water to
test pressure, check
each joint, ensure
there is no leakage.
Then put on the
protective sheath.

Cover the ceramic
tiles on the wall,
pay attention to
the installation
depth.
Reference line
of finished wall
Plug
Take off the protective
sheath and plug.
Flow water to clean the
pipes.
Blue
Red Blue
Red
Filters
Connecting
Pipes
Wrap the teflon tape around two
connecting pipes and screw them
into the shower seat. Please
be noted that the red and blue
marks must be rightly matched.
Tighten all when finished.
Shower Arm
Escutcheon
M3 Screw
Install the escutcheon to the
shower arm.
Protective
Sheath
Shower
Head
Remove the protective
sheath from the shower
arm and connect the
shower arm with the
shower head.
End Cap
M5 Panhead Screw
Take off the end cap
(take care not to damage
the shower body). Fix the
shower head and shower
arm with M5 panhead
screw. Then reinstall the
end cap back.
Shower Head
Put the shower head
on the connecting
pipes. Make sure it
is right against the
wall.

M5 Screw
Tighten M5 screw
by S2.5 wrench.
When completed, run water
to check if the installation is
proper. The diagram shows
water flows from the rain
shower.
Water flows from
the rain stream.
Shower Head
M5 Screw
Loosen M5 screw by
S2.5 wrench and carefully
take off the shower head.
Red
Blue
Filters
Blue
Red
Connecting Pipes
Screw off the
connecting pipes
and clean the filters.
Flow water to get rid of
dirt inside the pipes.
V. Maintenance (Diagram 21~24)
If flow rate is lessened after a period of usage, it is possibly because debris
blocks the filters due to poor water quality. Cleaning method should be taken
as followed. First, turn off the main vlave. Take off the filters as shown in the
Diagram 21 and 22. Use brush and vinegar to remove dirt and debris from the
filters, and rinse with clean water. Then use flush water to get rid of dirt and
debris in pipes (Diagram 23), and install the shower head back according to
Diagram 13,17 and 18. Please be noted that the red and blue marks must be
rightly matched.
If water flow from the rain shower becomes lessened or does not spray
evenly, it might be debris blocking the outlet. Gently squeeze those
rubber outlets on the shower head with fingers as shown in Diagram 24. Then
wash debris out with running water.