Cadel VERA 7.0 UP User manual

EN
USER MANUAL
Pellet Stove
Original Instructions | ©2022 CADEL srl | All rights reserved - Tutti i diritti riservati
new
VERA 7, 7.0, 7.0 UP  INDIGO EVO, INDIGO EVO 7  LORD7, 7.0 
FLOYD 5.0  FLOYD 7.0  ELANE 9  AMARANTO 9

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
2
SUMMARY
1 MANUAL SIMBOLOGY....................................3
2 DEAR CUSTOMER..........................................3
2.1 REVISIONS TO THE PUBLICATION............................4
2.2 CARE OFTHE MANUAL AND HOWTO CONSULT IT...4
3 SAFETY REQUIREMENTS ............................5
4 CAUTIONS  WARRANTY CONDITIONS.............6
4.1 INFORMATION.........................................................6
4.2 INTENDED USE ........................................................6
4.3 PRODUCT PERFORMANCE CHECKS..........................6
4.4 WARRANTY CONDITIONS........................................7
5 SPARE PARTS ...............................................8
6 DISPOSAL OF MATERIALS..............................8
6.1 WARNINGS FOR THE CORRECT DISPOSAL OF THE
PRODUCT...........................................................................8
6.2 INFORMATION FOR MANAGEMENT OF ELECTRIC AND
ELECTRONIC APPLIANCEWASTE CONTAINING BATTERIES OR
ACCUMULATORS ................................................................9
6.3 INSTRUCTIONS FOR PACKAGING DISPOSAL............9
7 WIFI  BLUETOOTH CONNECTION ................10
7.1 NAVEL STAND ALONE OPTIONAL........................10
8 USE ...........................................................11
8.1 INTRODUCTION.....................................................11
8.2 CONTROL PANEL ...................................................12
8.3 USER MENU...........................................................13
8.3.1 MENU M1  CLOCK SETTING................................16
8.3.2 MENU M2  CHRONO SETTING............................16
8.3.3 MENU M3  LANGUAGE SELECTION....................18
8.3.4 MENU M4  STANDBY........................................18
8.3.5 MENU M5  BUZZER............................................19
8.3.6 MENU M6  FIRST LOAD......................................19
8.3.7 MENU M7  STOVE STATUS..................................19
8.3.8 MENU M8  ENGINEER SETTINGS........................19
8.3.9 MENU M9  PELLETTYPE....................................20
8.3.10 MENU MA  FLUE TYPE........................................20
8.3.11 MENU MB  EXIT .................................................20
8.4 STOVE SWITCHON................................................20
8.5 FAILED IGNITION...................................................21
8.6 POWER FAILURE....................................................21
8.7 TEMPERATURE SETTING........................................21
8.8 POWER SETTING ...................................................21
8.9 SWITCHING OFF ....................................................21
8.10 CONNECTIONTOTHE EXTERNALTHERMOSTAT.....21
9 FUEL..........................................................21
9.1 FUEL......................................................................21
9.2 PELLET SUPPLY .....................................................22
9.3 PELLET REFUELLINGTIMER...................................22
10 VENTILATION .............................................23
11 REMOTE CONTROL OPTIONAL....................23
12 SAFETY DEVICES AND ALARMS ....................24
12.1 PRESSURE SWITCH................................................24
12.2 SMOKETEMPERATURE PROBE ..............................24
12.3 CONTACTTHERMOSTAT INTHE FUEL HOPPER.......24
12.4 ELECTRICAL SAFETY..............................................24
12.5 SMOKE FAN...........................................................24
12.6 GEAR MOTOR.........................................................24
12.7 TEMPORARY POWER CUT......................................24
12.8 FAILED STARTUP..................................................24
12.9 BLACKOUT WITHTHE BOILER ON..........................25
12.10 FLUE GASTEMPERATURE PROBE ALARM..............25
12.11 FLUE GAS OVERTEMPERATURE ALARM.................25
12.12 FAULTY FLUE GAS ENCODER ALARM.....................25
12.13 FAILED IGNITION ALARM ......................................26
12.14 NO PELLET ALARM................................................26
12.15 THERMAL SAFETY OVERHEATING ALARM ............26
12.16 NO NEGATIVE PRESSURE ALARM..........................26
12.17 ALARM ALERTS .....................................................27
12.18 ALARM RESET .......................................................29
13 ROUTINE MAINTENANCE.............................29
13.1 INTRODUCTION.....................................................29
13.2 BEFORE EACH STARTUP.......................................30
13.3 BURNING POT AND ASHTRAY CLEANING .............30
13.4 HOPPER CLEANING ...............................................31
13.5 FUME PIPES ANNUAL CLEANING ..........................31
13.6 GENERAL CLEANING..............................................31
13.7 CLEANING OF PAINTED METAL PANELS ................31
13.8 CLEANING OF CERAMIC AND STONE PANELS........31
13.9 GASKET REPLACEMENT.........................................32
13.10 GLASS CLEANING..................................................32
13.11 SHUTDOWN END OF SEASON.............................32
13.12 CHECKINGTHE INNER COMPONENTS....................32
14 IN CASE OF ANOMALY..................................33
14.1 PROBLEM SOLVING ...............................................33
15 TECHNICAL DOCUMENTATION FOR LOCAL SPACE
HEATERS ACCORDING TO COMMISSION REGULATIONS
EU 2015/1185  EU 2015/1186 PRODUCT FICHE
.................................................................36

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
3
1 MANUAL SIMBOLOGY
USER
AUTHORISED TECHNICIAN
(ONLY to interpret or the Stove-manufacturer or the AuthorizedTechnician of
Technical Assistance Service approved by the Stove-manufacturer)
SPECIALIZED STOVE-REPAIRER
CAUTION:
READ CAREFULLY THE NOTE
CAUTION:
DANGER OR IRREVERSIBLE DAMAGE POSSIBILITY
• The icons with the stylized figures indicates whom the subject dealt in the paragraph is addressed to (between the User and/
or the AuthorizedTechnician and/or the Specialized Stove-repairer).
• WARNING symbols indicates an important note.
2 DEAR CUSTOMER
Dear Customer,
Our products are designed and manufactured in accordance with standards in force, with high quality materials and using our
extensive experience in the transformation processes.
To get the best performance, we suggest you read the instructions in this manual carefully.
This installation guide is an integral part of the product: ensure that the manual is always supplied with the appliance, even if it
changes owner. If the manual is lost, you can request another copy from the localTechnical Dept. or download it directly from the
company’s website.
All local regulations, including those referring to national and European standards, must be observed when installing the appliance.
In Italy, for the installation of systems with a biomass below 35KW, refer to the Ministerial Decree 37/08 and the qualified instal-
lation technician with the suitable requirements must issue a certificate of compliance for the system installed. (By system we
intend Stove+Flue+Air inlet).
Our solid bio-combustible products, (hereinafter called“Products”) are designed and manufactured in compliance with one of the
following European standard harmonised to Regulation (UE) no. 305/2011 for construction products:
EN 14785:“Residential space heating appliances fired by wood pellets”
EN 13240:“Room heaters fired by solid fuel.”
EN 13229:“Inset appliances including open fires fired by solid fuels”
EN 12815: “Residential cookers fired by solid fuel”
The products also comply with the essential requirements of Directive 2009/125/EC (Eco Design) and, where applicable, Direc-
tives:
2014/35/EU (LVD - LowVoltage directive)
2014/30/EU (EMC - Electromagnetic Compatibility directive)
2014/53/EU (RED - Radio Equipment directive)
2011/65/EU (ROhS)
Hereby CADEL S.r.l. declares that the radio equipment type Easy Connect Plus + Navel Stand Alone is in compliance with
Directive 2014/53/EU.
Accordingto (EU) No. 305/2011 regulation, the"Declarationof Performance"and"Declarationof Conformity"are available online,

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
4
in the download area, at the web sites:
- www.cadelsrl.com
- www.free-point.it
- www.pegasoheating.com
Having specified the above, we highlight and report that:
• This manual and technical data sheet, also available on our website, bear all of the specific indications and necessary
and essential information to choose the product, to install it correctly and to properly size the smoke expulsion system;
• the Products must be installed, controlled and serviced by a qualified operator, according to the instructions in this ma-
nual and in compliance with the laws and installation and maintenance standards in force in individual countries, so as to
provide an efficient heating system, properly sized according to the needs of the home.
• If the Products are thermally stressed, constantly operating for several hours at high power (e.g. 3, 4 hours a day at ou-
tputs P4 or P5), we recommend more frequent cleaning and reducing the interval between routine maintenance operations
according to the operating condition of the product. We furthermore point out that these operating conditions increase the
risk of premature wear of the product, especially those parts exposed to the direct heat of the fire (e.g. combustion chamber),
the original condition of which can undergo modifications and deterioration which, among other things, could generate noise
during operation of the unit due to mechanical expansion.
The manufacturer will not be held liable if the above information is ignored.
2.1 REVISIONS TO THE PUBLICATION
The content of this manual is strictly technical and the property of CADEL S.r.l.
No part of this manual may be translated into other languages, adapted and/or reproduced, even in part, in other mechanical and/
or electronic form or media, for photocopies, recordings or other, without the prior written authorisation of CADEL S.r.l.
The company reserves the right to make changes to the product at any time without prior notice.The owner company reserves its
rights according to law.
2.2 CARE OF THE MANUAL AND HOW TO CONSULT IT
• Take care of this manual and store it in an easily and quickly accessible place.
• Should this manual be lost or destroyed, request a copy from your retailer or directly from the authorisedTechnical assistance
department. It can also be downloaded from the company’s website.
• “Bold text” requires special attention.

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
5
3 SAFETY REQUIREMENTS
• Installation, electrical connection, functional verification and maintenance must only be
performed by qualified or authorised personnel.
• Live electrical parts: disconnect the product from the 230V power supply before perfor-
ming any maintenance operation. Only power the product after completing assembly.
• Special maintenance must only be performed by authorised and qualified personnel.
• All local regulations, including those referring to national European standards, must be
respected during appliance installation.
• The manufacturer declines any responsibility in case of installation which are not in com-
pliance with current regulations, in case of a wrong room ventilation system, in case of an
electric connection which is not in compliance with regulations and in case of a wrong use of
the appliance.
• It is forbidden to install the stove in bedrooms, bathrooms and in rooms used for storing
combustible materials and in one-room flats.
• The installation in one-room flats is allowed if they are in sealed chamber.
• In any case the stove must not be installed in rooms where it can get in touch with water or
water splashes because this can cause burn hazards and short-circuit.
• Please check that the floor has an adequate load capacity. If the existing one does not
satisfy this requirement, appropriate measure should be provided (for example a plate for di-
stributing the load).
• For safety fire regulations the distances from flammable or sensible to heat objects (sofas,
pieces of furniture, wooden covering, etc...) must be respected.
• If there are highly flammable objects (curtains, fitted carpet, etc...), all these distances
must be further increased with 1 meter.
• If the floor is made of combustible material, we recommend using a protector made of in-
combustible material (steel, glass, etc.) that also protects the front part from any falling burnt
particles during cleaning.
• The electrical cable must not get in touch with the fume exhaust pipe and nor with every
other part of the stove.
• The user, or whoever is operating the product, must read and fully understand the contents
of this installation and use guide before performing any operation. Errors or incorrect settings
can cause hazardous conditions and/or poor operation.
• The type of fuel to use is only the pellets.
• Do not use the appliance as waste inceneretor.
• Do not place laundry on the product to dry. Any clothes horses or similar objects must be
kept at a safe distance from the product. Fire hazard.
• It is forbidden to operate the product with the door open or the glass broken.
• It is forbidden to modify the appliance without authorization.
• Do not use flammable liquids during the ignition (alcool, petrol, oil, etc...).
• After a failed ignition the burning pot must be empty from the amassed pellets, before
starting the stove up again.
• The pellet hopper must always be closed with its own lid.
• Before of every intervention leave the fire completely extinguish till the cooling and always
disconnect the plug from the electric socket.
• This appliance can be used by children aged from 8 years and above and persons with re-
duced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Packaging are not toys and could cause suffocation or strangulation and other health ha-
zards! People (childreen included) with reduced mobility, psycological deseases or without

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
6
experience and knowledge must be kept away from packaging.The stove IS NOT a toy.
• Childreen must be constantly overseen in order to assure that they do not play with the
appliance.
• During its running, the stove reaches high temperatures: keep away childreen and animals
and for your safety please use appropriate fireproof devices, such as heat-protecting gloves.
• The stove is equipped with a safety device that stops the feed screw immediately when the
pellet loading door is opened.This safety device (standard EN 60335-2-102) prevents the user
from coming into contact with the moving parts of the appliance.
• The chimney flue must be cleaned, since the soot and unburnt oil deposits reduce its sec-
tion so blocking the draught. In great quantities they can flare up.
• If the pellets are of bad quality (if contains sizing agents, oils, varnishes, plastic remains or
if it is mealy), deposits will form along pellets drop pipe during the running. When the stove is
switched off, these remains could form little hot coals that rising along the pipe could reach the
pellets on the hopper burning them and creating a thick and harmful smoke inside the room.
Please always keep the hopper closed with its own lid. If the pipe is sooty, please clean it.
• In case it would be necessary to extinguish the fire emitted by the stove or by the chimney
flue, use a fire-extinguisher or contact the firemen. DO NOT use water to extinguish the fire
inside the burning pot.
• Remote control (if present): keep the batteries out of the reach of children, risk of swal-
lowing. If swallowed, seek medical advice immediately.
• Pellets must not be fed manually into the burner - this wrong behaviour can generate an
abnormal amount of unburned gas, with a risk of explosion in the chamber.
4 CAUTIONS  WARRANTY CONDITIONS
4.1 INFORMATION
• Please contact the retailer or qualified personnel for any information, problem or malfunction.
• Only use the fuel specified by the manufacturer.
• When the product is switched on for the first time, it is normal for it to emit smoke due to the paint heating up for the first time.
Therefore make sure the room it is installed in is well-ventilated.
• Periodically check and empty the inspectionable parts of the smoke duct (e.g.Tee fitting caps)
• Have the smoke outlet system periodically checked and cleaned
• The product is not a cooking appliance.
• Always keep the cover of the fuel hopper closed.
• Store this installation and user manual with care as it must accompany the product for the duration of its useful life. If the
product is sold or transferred to another user, always ensure the manual is also handed over.
4.2 INTENDED USE
The product only works with wood pellets and must be installed inside a room.
4.3 PRODUCT PERFORMANCE CHECKS.
All our products undergo ITT TESTS carried out by a notified third party laboratory (system 3) and in accordance with Regulation
(EU) number 305/2011“Construction products”, according to standard EN 14785:2006 for household appliances and“Machinery
Directive”EN 303-5 for boilers.
In the case of tests for any market surveillance or inspections by third parties, please consider the following warnings:
•
• To reach the declared performance levels, the product must perform an operating cycle of at least 6/8 hours beforehand.
• Set the average draught of the combustion fumes as specified in the“technical product features”table
• The type of pellets used must comply with the current EN ISO 17225-2 class A1 regulation. Fir pellets are usually used for
certification.
• Theamountofthermalenergycanvaryaccordingtothelengthandcalorificvalueofthefuel.Thismayrequiresomeadjustments
(accessed from the user menu) to comply with the hourly consumption specified in the “technical product features” table.
Using class A1 pellets guarantees a calorific value that is likely to be close to that used in the product certification; the size of
the pellet grains can significantly affect hourly fuel loading and consequently performance; it is therefore suggested to use
pellets with a 6 mm diameter and an average length of around 24 mm (avoid pellets that are too long or excessively crushed).

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
7
• With wood-burning appliances, the fuel must comply with the current EN ISO 17225-5 class A1 regulation. Check the correct
moisture of the fuel, as it must be within the range of 12 - 20% (it is best if the moisture is close to 12%, as is normally used in
certification). As the fuel moisture increases, different combustion air settings are required, which are implemented from the
combustion air register, thereby modifying the mixture of primary and secondary air
• It is important to check the operation of devices that can affect performance (for example air fans or electric safety devices) in
case of damage due to handling.
• Nominal performance has been obtained by setting the maximum flame power and room ventilation in automatic mode.
4.4 WARRANTY CONDITIONS
The duration, conditions and limitations of CADEL S.r.l. can be found on the guarantee card enclosed with the device.
The company guarantees the product, with the exception of elements subject to normal wear listed below, for a period of
2 (two) years from the date of purchase attested by:
• a document to serve as proof of purchase (invoice and/or receipt) that shows the name of the vendor and the date on which
the purchase was made;
• forwarding of the completed certificate of guarantee within 8 days of purchase.
Furthermore, the product must be installed and started by specialised personnel who must, where provided, issue a declaration of
conformity of the plant and of the proper functioning of the product, for the warranty to be valid and effective.
We recommend testing the product before completion with the relative finishes (claddings, painting of walls, etc.).
Installations not meeting the current standards, improper use and lack of maintenance as expected by the manufacturer, void the
product warranty.
The guarantee is valid on the condition that the instructions and warnings contained in the use and maintenance manual are
observed, and therefore the product is used correctly.
The replacement of the entire system or the repair of one of its components does not extend the guarantee period, and the original
expiry date remains unchanged.
The guarantee covers the replacement or free repair of parts recognised as being faulty at source due to manufacturing
defects.
To benefit from the guarantee, in the event of a fault, the customer must have the guarantee certificate and present it with the
proof of purchase document to theTechnical Assistance Office.
The guarantee does not cover malfunctions and/or damage to the appliance that arise due to the following causes:
• Damage caused during transportation or relocation.
• All parts that develop faults due to negligence or improper use, incorrect maintenance, installation that does not comply with
the manufacturer's instructions (always refer to the installation and use manual provided with the appliance).
• Incorrect dimensioning with regards to the use or faults in the installation or failure to adopt the necessary devices to guaran-
tee proper execution.
• Improper overheating of the equipment, use of fuels not conforming to the types and quantities indicated in the instructions
provided.
• Further damage caused by incorrect user interventions in an attempt to fix the initial fault.
• Worsening of the damage due to the continued use of the equipment by the user, once the defect has been noticed.
• In the presence of a boiler, any corrosions, incrustations or breaks caused by water flow, condensation, hardness or acidity of
the water, improperly performed descaling treatments, lack of water, mud or limescale deposits.
• Inefficiency of chimneys, flues or parts of the plant affecting the equipment.
• Damagecausedbytamperingwiththe appliance,atmosphericagents,naturaldisasters, vandalism, electrical discharges,fires,
faults in the electric and/or hydraulic system.
• Failure to have the stove cleaned on an annual basis by an authorised technician or qualified personnel will result in the loss
of the warranty.
Also excluded from this guarantee are:
• Parts subject to normal wear such as gaskets, glass, claddings and cast iron grids, painted, chrome-plated or gilded parts,
handles and electric cables, bulbs, indicator lights, knobs, all parts which can be removed from the hearth.
• Variations in colour of the painted or ceramic/serpentine parts and craquelure ceramics as they are natural characteristics of
the material and product use.
• Masonry work.
• Plant parts (if present) not supplied by the manufacturer.
Any technical interventions on the product to eliminate the above-said defects and consequent damages must be agreed upon
with theTechnical Assistance Centre, who reserves the right to accept the relative appointment or not. However, said interventions
will not be carried out under warranty but as technical assistance to be granted at part of any eventual and specific agreed condi-

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
8
tions and in accordance with the fee in force for the work to be carried out.
The user will also be charged for any costs incurred to remedy the incorrect technical interventions, tampering or damage to the
appliance, not attributable to original faults.
Save for the legal or regulatory limits, the guarantee does not cover the containment of atmospheric and acoustic pollution.
The company declines all liability for any damage which may be caused, directly or indirectly, to persons, animals
or objects as a consequence of non compliance with any prescription specified in the manual, especially warnings
regarding installation, use and maintenance of the appliance.
5 SPARE PARTS
For each repair or adjustment which should be necessary, please contact the dealer where you purchased your stove or your nea-
restTechnical Assistance Service, specifying:
• Appliance model
• Serial number
• Type of problem
Use only original spare parts which you can find at ourTechnical Assistance Services.
6 DISPOSAL OF MATERIALS
6.1 WARNINGS FORTHE CORRECT DISPOSAL OF THE PRODUCT
The owner is the sole party responsible for demolishing and disposing of the product.This must be performed in compliance with
laws related to safety and environmental protection in force in his/her country.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special differentiated waste collection centre set up by the local authorities or to a retailer that provides this
service.
Separating and recycling prevents potential negative effects on the environment and health (often caused by inappropriately
disposing of product parts). It also allows materials to be recovered in order to obtain significant savings in energy and resources.
The following table and the exploded view it refers to highlight the main components that can be found in the device and indica-
tions on how to separate and dispose of them correctly when no longer used.
More specifically, the electric and electronic components must be separated and disposed of in authorised centres, in compliance
with theWEEE directive 2012/19/EU and the relative national transpositions.
Fig. 1 - Exploded drawing

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
9
LEGENDA WHERE TO DISPOSE MATERIALS
A. OUTER CLADDING If there is any, to be disposed of separately based on
the material used:
Metal
Glass
Tiles or ceramics
Stone
B. GLASS DOORS If there is any, to be disposed of separately based on
the material used:
Glass ceramic (fire door): to be disposed of with
inert or mixed waste
Tempered glass (oven door): to be disposed of with
glass
C. INTERIOR CLADDING If there is any, to be disposed of separately based on
the material used:
Metal
Refractory materials
Insulating panels
Vermiculite
Insulation, vermiculite and refractory materials
that have come into contact with flames or exhaust
gases (dispose of in mixed waste)
D. ELECTRIC AND ELECTRO-
NIC COMPONENTS
To be disposed of separately in authorised centres,
as indicated in theWEEE directive 2012/19/EU and
the relative national transposition.
Wiring, motors, fans, circulators, display panels,
sensors ignition plug, electronic cards, batteries.
E. METAL STRUCTURE To be disposed of separately with metal -
F. COMPONENTSTHAT CAN-
NOT BE RECYCLED To be disposed of with mixed waste E.G.: Gaskets, rube piping, silicone or fibres, plastic.
G. HYDRAULIC COMPONENTS Piping, fittings, expansion vessel, valves. If there are any, to be disposed of separately based on the
material they are made of:
Copper
Brass
Stainless steel
Other materials
6.2 INFORMATION FOR MANAGEMENT OF ELECTRIC AND ELECTRONIC APPLIANCE WASTE CON
TAINING BATTERIES OR ACCUMULATORS
Fig. 2 - Waste disposal
This symbol, which is used on the product, batteries, accumulators or on the packaging or documents, means that at the end of its
useful life, this product, the batteries and the accumulators included must not be collected, recycled or disposed of together with
domestic waste.
Improper management of electric or electronic waste or batteries or accumulators can lead to the leakage of hazardous substances
contained in the product. For the purpose of preventing damage to health or the environment, users are kindly asked to separate
this equipment and/or batteries or accumulators included from other types of waste and to arrange for disposal by the municipal
waste service It is possible to ask your local dealer to collect the waste electric or electronic appliance under the conditions and
following the methods provided by national laws transposing the Directive 2012/19/EU.
Separate waste collection and recycling of unused electric and electronic equipment, batteries and accumulators helps to save
natural resources and to guarantee that this waste is processed in a manner that is safe for health and the environment.
For more information about how to collect electric and electronic equipment and appliances, batteries and accumulators, please
contact your local Council or Public Authority competent to issue the relevant permits.
6.3 INSTRUCTIONS FOR PACKAGING DISPOSAL
The material that the appliance’s packaging is made of must be managed correctly, in order to make collection, reuse, recovery
and recycling easier, where possible.
The table below illustrates the possible components that the packaging is made of, and the relative instructions for correct disposal.

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
10
DESCRIPTION CODE MATERIAL SYMBOL DIRECTIONS FOR COLLECTION
-WOOD BED
-WOOD CAGE
-WOOD PALLET
WOOD
FOR 50
SORTED waste collection
WOOD
Check with the competent body on
how to dispose of this packaging at
the recycling depot
- CARDBOARD BOX
- CARDBOARD CORNER
- CARDBOARD SHEET
CORRUGATED CARDBOARD
PAP 20
SORTED waste collection
PAPER
Check the instructions of the com-
petent body
- APPLIANCE BAG
- BAG OF ACCESSORIES
- BUBBLEWRAP
- PROTECTIVE SHEET
- LABELS
POLYETHYLENE
LD PE 04
SORTED waste collection
PLASTIC
Check the instructions of the com-
petent body
- POLYSTYRENE
- FOAM PEANUTS POLYSTYRENE PS 6
SORTED waste collection
PLASTIC
Check the instructions of the com-
petent body
- STRAP
-TAPE POLYPROPYLENE PP 5
SORTED waste collection
PLASTIC
Check the instructions of the com-
petent body.
- SCREWS
- STAPLES FOR STRAP
- FASTENING BRACKET
IRON
FE 40
SORTED waste collection
METAL
Check with the competent body on
how to dispose of this packaging at
the recycling depot
7 WIFI  BLUETOOTH CONNECTION
7.1 NAVEL STAND ALONE OPTIONAL
Procedure if only valid for models with NAVEL STAND ALONE Wi-Fi technology.
ATTENTION! Installation must ONLY be carried out by specialised personnel.
The manufacturer will not be held responsible for injury to persons or damage to property or in the event of
failed operation.
The Wi-Fi module uses the domestic Wi-Fi network; ensure there is enough coverage in the
place of installation.
N.B.: for stoves with a 3-button display, the programmable thermostat cannot be configured via the App.

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
11
Fig. 3 - NAVEL STAND ALONE module Fig. 4 - App EASY CONNECT PLUS
The documentation for connecting theWi-Fi and using the App are available online at the following addresses:
https://www.cadelsrl.com/donwload-wi-fi/
http://www.free-point.it/it/downloads/
https://www.pegasoheating.com/it/documenti/
8 USE
8.1 INTRODUCTION
To have the best performance with the lowest consumption please follow the here descripted instructions.
• The lightning of the pellets occurs very easily if the installation is correct and if the chimney flue is efficient.
• Switch on the stove at Power 5, for at least 2 hours, in order to enable the materials which make up the boiler and the
fireplace to adjust the inner springing stress. After 2 hours, the smell of paint and smoke will disappear.
• By using the stove the varnish inside the combustion chamber could be subjected to alterations. This occurrence can be attri-
buted to different reasons: an excessive stove overheating, the presence of chemical agents in bad quality pellets, bad chimney
draught, etc.Therefore varnish endurance in the combustion chamber cannot be guarantee.
Oily plant waste and lacquers can cause smells and smoke during the first working hours: it is advisable to
ventilate the room because they could be noxious to people and animals.

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
12
Set values from 1 to 5 are defined by the manufacturer and they can be changed only by an authorized tech-
nician.
The product will be subject to expansion and contraction during the ignition and cooling stages, therefore
slight creaking noises may be heard. This is perfectly normal as the structure is made of laminated steel and
must not be considered a defect.
8.2 CONTROL PANEL
The display allows you to dialogue with the stove by simply pressing a few buttons. A display with scrolling text and LED indicators
inform the user about the stove's operating status.
Meaning of the buttons (see Fig. 5)
Fig. 5 - Display: 3 buttons
REFERENCE BUTTON DESCRIPTION MODE ACTION
1Decreases tempera-
ture and power
TEMPERATURE SETTING Decreases the value of the ambient
temperature SETTING
PROGRAMMING Decreases the selected parameter
POWER SETTING Decreases the value of the operating
power
2Increases the tempe-
rature and power
TEMPERATURE SETTING Increases the value of the ambient
temperature SETTING
PROGRAMMING Increases the selected parameter
POWER SETTING Increases the value of the operating
power
3 ON/OFF
WORK Pressed for 2 seconds, it turns the
stove on or off accordingly
PROGRAMMING Allows you to select the parameters
to be programmed
Meaning of the LEDs that are on (see Fig. 6):
Fig. 6 - Display: LEDs on
REFERENCE SYMBOL DESCRIPTION LED ON
1 AMBIENT SETTING Ambient setting programming

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
13
REFERENCE SYMBOL DESCRIPTION LED ON
2 POWER SETTING Power setting programming
3 ON/OFF Work status
4 CHRONO Chrono is enabled
5 ALARM Stove is in alarm
6 FEED SCREW ON Feed screw moving
7 HEAT EXCHANGER Heat exchanger on
8 SPARK PLUG Ignition spark plug
8.3 USER MENU
The following table briefly describes the menu structure; this paragraph solely focuses on the selections available to the user.
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
M1 Set orologio
M1-SEt cLocK
01 - Day of the week M-T-W-T-F-S-S Mond-tuES-uEdn-tHur-Frid-
SAtu-Sund
02 - Clock hours
02-tiME cLocK 0-23
03 - Clock minutes
03-MinutES cLocK 0-59
04 - Clock day
04-dAy cLocK 1-31
05 - Clock month
05-MontH cLocK 1-12
06 - Clock year 00-99
M2 - Chrono setting
M2-SEt cHrono M2-1 - Enable chrono
M2-1 cHrono EnAbLE 01 - enable chrono
01-cHrono EnAbLE on/off
M2-2 - Daily programming
M2-2 ProGrAM dAy 01 - daily chrono
01-cHrono dAyLy on/oFF
02 - start 1 day
02-StArt 1 dAyLy oFF-0-23:50

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
14
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
03 - stop 1 day
03-StoP 1 dAyLy oFF-0-23:50
04 - start 2 day
04-StArt 2 dAyLy oFF-0-23:50
05 - stop 2 day
05-StoP 2 dAyLy oFF-0-23:50
M2-3 -Weekly programming
M2-3 -ProGrAM uEEK 01 - week chrono
01-crono uEEKLy on/oFF
02 - start Prg 1
02-StArt PrG1 oFF-0-23:50
03 - stop Prg 1
03-StoP PrG1 oFF-0-23:50
04 - Monday Prg1
04-Mond PrG1 on/oFF
05 -Tuesday Prg 1
05-tuES PrG1 on/oFF
06 -Wednesday Prg 1
06-uEdn PrG1 on/oFF
07 -Thursday Prg1
07-tHur PrG1 on/oFF
08 - Friday Prg 1
08-Frid PrG1 on/oFF
09 - Saturday Prg 1
09-SAtu PrG1 on/oFF
10 - Sunday Prg 1
10-Sund PrG1 on/oFF
11 - start Prg 2
11-StArt PrG2 oFF-0-23:50
12 - stop Prg 2
12-StoP PrG2 oFF-0-23:50
13 - Monday Prg2
13-Mond PrG2 on/oFF
14 -Tuesday Prg 2
14-tuES PrG2 on/oFF
15 -Wednesday Prg 2
15-uEdn PrG2 on/oFF
16 -Thursday Prg2
16-tHur PrG2 on/oFF
17 - Friday Prg 2
17-Frid PrG2 on/oFF
18 - Saturday Prg 2
18-SAtu PrG2 on/oFF
19 - Sunday Prg 2
19-Sund PrG2 on/oFF
20 - start Prg 3
20-StArt PrG3 oFF-0-23:50
21 - stop Prg 3
21-StoP PrG3 oFF-0-23:50
22 - Monday Prg3
22-Mond PrG3 on/oFF
23 -Tuesday Prg 3
23-tuES PrG3 on/oFF
24 -Wednesday Prg 3
24-uEdn PrG3 on/oFF
25 -Thursday Prg3
25-tHur PrG3 on/oFF
26 - Friday Prg 3
26-Frid PrG3 on/oFF

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
15
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
27 - Saturday Prg 3
27-SAtu PrG3 on/oFF
28 - Sunday Prg 3
28-Sund PrG3 on/oFF
29 - start Prg 4
29-StArt PrG4 oFF-0-23:50
30 - stop Prg 4
30-StoP PrG4 oFF-0-23:50
31 - Monday Prg4
31-Mond PrG4 on/oFF
32 -Tuesday Prg 4
32-tuES PrG4 on/oFF
33 -Wednesday Prg 4
33-uEdn PrG4 on/oFF
34 -Thursday Prg4
34-tHur PrG4 on/oFF
35 - Friday Prg 4
35-Frid PrG4 on/oFF
36 - Saturday Prg 4
36-SAtu PrG4 on/oFF
37 - Sunday Prg 4
37-Sund PrG4 on/oFF
M2-4 -Weekend program
M2-4-ProGrAM u-End 01 - weekend chrono
01-cHrono uEEK End on/oFF
02 - start weekend 1
02-StArt 1 uEEK End oFF-0-23:50
03 - stop weekend 1
03-StoP 1 uEEK End oFF-0-23:50
04 - start weekend 2
04-StArt 2 uEEK End oFF-0-23:50
05 - stop weekend 2
05-StoP 2 uEEK End oFF-0-23:50
M2-5 - Exit
M2-5-EScAPE set
M3 - Choose language
M3-LAnGuAGE 01 - Italian
01-LinG itA set
02 - English
02-LinG EnG set
03 - French
03-LinG FrE set
04 - German
04-LinG dEu set
05 - Spanish
05-LinG SPA set
06 - Portuguese
06-LinG Por set
M4 - Stand-by
M4-StAnd-by 01 - Stand - by
01-StAnd-by on/oFF
M5 - Buzzer
M5 buCCEr 01 - Buzzer
01-buCCEr on/oFF
M6 - First load
M6 LoAd initiAL

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
16
LEVEL 1 LEVEL 2 LEVEL 3 VALUE
01 - First load
01-LoAd initiAL 90"
M7 - Stove status
M7 StAtE StoVE 01 - Stove status
01-StAtE StoVE 01 - Feed screw status info
02 -T minutes info
03 -Thermostat status info
04 - Flue gas status info
05 - Flue gas extraction rpm
status info
M8 - Engineer settings
M8 SEt tEcHnic 01 - Password
01-KEy AccESS set
M9 - Pellet type
M9 tyPE PELLEt 01 - Loading pellets
01-Pr 54 LoAd PELLEt da -9 a +9
MA - Flue type
MA tyPE cHiMnEy 01 - Flue extractor
01-Pr 55 SMoKE cHiMnEy da -9 a +9
MB - Exit
Mb EScAPE 01 - Exit
01-EScAPE set
8.3.1 Menu M1 - CLOCK SETTING
Set the current time and date.The board has a lithium battery that assures the internal clock life of more than 3-5 years.
Press the P1 button for 2 seconds to access the general programming menus. Pressing P1 (decreases) or P2 (increases) selects item
M1, and M1 SEt cLocK will scroll "M1-SEt cLocK "(see Fig. 7).
Fig. 7 - Display: M1
8.3.2 Menu M2 - CHRONO SETTING
Submenu M2-1 Enable chrono
The menu shown on the M2 - 1 chrono setting "cHrono EnAbLE " display allows you to globally enable and disable all the chro-
nothermostat functions. Enable by pressing button P3 and then pressing P1 or P2 for the On or Off section. Confirm with the P3
button (see Fig. 8).
Fig. 8 - Display: enables
Submenu M2 - 2 - Day program

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
17
After selecting the M2 - 2 day program " ProGrAM dAy " menu, using the P3 button you will scroll through the various daily
chrono programming parameters, including enabling it (see Fig. 9).
Fig. 9 - Display: crono
Two operating ranges can be set, the first with START1 Day "StArt 1 dAyLy " and STOP1 Day "StoP 1 dAyLy ", the second with
START2 Day "StArt 2 dAyLy " and STOP2 Day "StoP 2 dAyLy ", delimited by the times set according to the table below where the
OFF setting indicates the clock to ignore the command. Use buttons P1 (decreases) and P2 (increases) to vary, and P3 to confirm.
DAY PROGRAM
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-2-01 cHrono dAyLy Enables the daily chrono ON/OFF
M2-2-02 StArt 1 dAyLy activation time OFF-0-23:50
M2-2-03 StoP 1 dAyLy deactivation time OFF-0-23:50
M2-2-04 StArt 2 dAyLy activation time OFF-0-23:50
M2-2-05 StoP 2 dAyLy deactivation time OFF-0-23:50
Submenu M2 - 3 - weekly program
TheM2-3WeeklyProgram"ProGrAM uEEK "menuallows youtoenable/disable and set the weeklychronothermostatfunctions.
The weekly function has 4 independent programs. Furthermore, by setting OFF in the time field, the clock ignores the correspon-
ding command.
The tables below summarise the weekly program function. Press the P3 button to access the next function and confirm the value.
It is possible to exit the menu by pressing the P3 button for long.
ENABLING WEEKLY CHRONO
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-3-01 crono uEEKLy Enables the weekly chrono ON/OFF
PROGRAM 1
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-3-02 StArt PrG1 activation time OFF-0-23:50
M2-3-03 StoP PrG1 deactivation time OFF-0-23:50
M2-3-04 Mond PrG1
reference day
on/off
M2-3-05 tuES PrG1 on/off
M2-3-06 uEdn PrG1 on/off
M2-3-07 tHur PrG1 on/off
M2-3-08 Frid PrG1 on/off
M2-3-09 SAtu PrG1 on/off
M2-3-10 Sund PrG1 on/off
PROGRAM 2
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-3-11 StArt PrG2 activation time off-0-23:50
M2-3-12 StoP PrG2 deactivation time off-0-23:50
M2-3-13 Mond PrG2
reference day
on/off
M2-3-14 tuES PrG2 on/off
M2-3-15 uEdn PrG2 on/off
M2-3-16 tHur PrG2 on/off
M2-3-17 Frid PrG2 on/off
M2-3-18 SAtu PrG2 on/off
M2-3-19 Sund PrG2 on/off

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
18
PROGRAM 3
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-3-20 StArt PrG3 activation time off-0-23:50
M2-3-21 StoP PrG3 deactivation time off-0-23:50
M2-3-22 Mond PrG3
reference day
on/off
M2-3-23 tuES PrG3 on/off
M2-3-24 uEdn PrG3 on/off
M2-3-25 tHur PrG3 on/off
M2-3-26 Frid PrG3 on/off
M2-3-27 SAtu PrG3 on/off
M2-3-28 Sund PrG3 on/off
PROGRAM 4
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-3-29 StArt PrG4 activation time off-0-23:50
M2-3-30 StoP PrG4 deactivation time off-0-23:50
M2-3-31 Mond PrG4
reference day
on/off
M2-3-32 tuES PrG4 on/off
M2-3-33 uEdn PrG4 on/off
M2-3-34 tHur PrG4 on/off
M2-3-35 Frid PrG4 on/off
M2-3-36 SAtu PrG4 on/off
M2-3-37 Sund PrG4 on/off
Submenu M2 - 4 - weekend program
Allows you to enable/disable and set the weekend chronothermostat functions (day 6 and 7, i.e. Saturday and Sunday). Enable
by pressing the P3 button in 01 - the weekend chrono "cHrono uEEK End" setting and set“on”" using the P1 (decreases) or P2
(increases) button. Setting the [CS:Grassetto:02 - Start 1 weekend[2:] "StArt 1 uEEK End " and 03 - Stop1 weekend times "StoP
1 uEEK End " sets the operating period for Saturday, "SAtu " whereas 04 - Start 2 weekend " StArt 2 uEEK End " and 05 - Stop 2
weekend " StoP 2 uEEK End " sets the stove operation for Sunday "Sund ".
WEEK-END PROGRAM
MENU LEVEL SELECTION MEANING POSSIBLE VALUES
M2-4-01 cHrono uEEK End Enables the weekend chrono on/off
M2-4-02 StArt 1 uEEK End activation time off-0-23:50
M2-4-03 StoP 1 uEEK End deactivation time off-0-23:50
M2-4-04 StArt 2 uEEK End activation time off-0-23:50
M2-4-05 StoP 2 uEEK End deactivation time off-0-23:50
8.3.3 Menu M3 - LANGUAGE SELECTION
Allows you to select the dialogue language from those available (see vedi Fig. 10).To switch to the next language press P2 (incre-
ases), to go backwards press P1 (decreases), and to confirm press P3.
Fig. 10 - Display: language
8.3.4 Menu M4 - STAND-BY
Allows you to enable or disable the M4 - Stand-by " M4 StAnd-by "mode (see 14366). Once the M4 menu has been selected with
the P3 button, press P1 (decreases) or P2 (increases) to change the state from ON to OFF and viceversa.

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
19
Fig. 11 - Display: stand-by
8.3.5 Menu M5 - BUZZER
Allowsyoutoenable or disable the buzzerofthe controllerwhenalarms areindicated (seeFig.12).Enableordisable with buttons
P1 or P2, and confirm with P3.
Fig. 12 - Display: buzzer
8.3.6 Menu M6 - FIRST LOAD
This function is only available when the stove is OFF and allows the feed screw to be loaded with the first start-up of the stove,
when the pellet tank is empty. After selecting menu M6, the message Press More "PrESS MorE " will scroll on the display (see Fig.
13).Then press P2 (increases).The flue gas fan turns on at maximum speed, the feed screw turns on (feed screw LED on) and they
remain until the time indicated on the display elapses (see Fig. 14), or until button P3 is pressed.
Fig. 13 - Display: press more Fig. 14 - Display: time left
8.3.7 Menu M7 - STOVE STATUS
Once in menu M7, after pressing button P3, the status of some variables scrolls on the display while the stove is working.The table
below shows an example of the display and its meaning of these values.
STATUS DISPLAYED MEANING
3,1” Pellet loading feed screw status
52’ Time out
Toff Thermostat status
106° Flue GasTemperature
1490 Flue gas extraction speed
8.3.8 Menu M8 - ENGINEER SETTINGS
This menu item is reserved for the stove installer. After entering the password (see Fig. 15) it allows you to set the various opera-
ting parameters of the stove using buttons P1 (decreases) and P2 (increases).
Fig. 15 - Display: key

CRISTAL 9 - LIFE 9 - CRISTAL PLUS 9 - ICON PLUS 9 - STEEL 9
20
8.3.9 Menu M9 - PELLET TYPE
It allows you to adjust the quality of combustion and the flame based on the fuel quality or draft of the flue (see Fig. 16).
Thanks to this adjustment the fuel supply in the burn pot may be modified by an amount between -18% and +18% (value from
-9 = -18% to +9 = +18%).
Fig. 16 - Display: pellet type
8.3.10 Menu MA - FLUE TYPE
The RPM of the flue gas extractor fan may be changed as a percentage to counter some draft issues or reduce extraction in case of
flues with excess draft (see Fig. 17).
The flue gas extractor speed adjustment can vary between -18% and +18% (value from -9 = -18% to +9 = +18%).
Fig. 17 - Display: ue type
8.3.11 Menu MB - EXIT
Selecting this item by pressing button P3 (see Fig. 18), exits the menu and returns to the previous state.
Fig. 18 - Display: exit
8.4 STOVE SWITCHON
We remind you that the first start-up must be carried out by skilled and authorised technical personnel who check that everything
is installed according to the regulations in force and verifies its functionality.
• If inside the combustion chamber there are booklets, manuals, etc. remove them.
• Check that the door is closed properly.
• Check that the plug is inserted into the socket.
• Before turning the stove on, make sure that the burn pot is clean.
Start up the stove by pressing button P3 for a few seconds so thatTurn on " StArt "is displayed. In these conditions, the stove goes
into the preheating state: the spark plugs go on (visible from the spark plug LED) together with the flue gas extraction fan. Any
anomalies during the ignition phase are shown on the display and the stove goes into alarm status.
The pellet loading phase starts after about 1 minute, and the display shows the message Pellet loading " LoAd PELLEt " and the
ON/OFF LED flashes intermittently. In the first phase, the feed screw loads the pellet into the burn pot. After the temperature of
the flue gas has reached and exceeded the contained value, the system goes into ignition mode and Fire present "FLAME LiGHt
" appears on the display and the ON/OFF LED flashes.
When the flue gas temperature has reached and exceeded the intended value, the stove goes into the normal operating mode. The
display shows the word Work " uorK " and the ON/OFF LED is lit.
The power can be set by keeping button P2 pressed and the room temperature can be set by pressing button P1.
At set intervals, an automatic burn pot cleaning is performed in order to prevent dash from accumulating. On the display you will
see Cleaning fire-pot“cLEAninG FirE-Pot”.
If this function lasts for a few seconds, it is NOT an alarm.