Cadel Martina User manual

©2013 CADEL srl | All rights reserved – tutti i diritti riservati
en PELLET STOVE
installation, use and maintenance manual
martina - vanessa - alessia - solaris

2MARTINA - VANESSA - ALESSIA - SOLARIS
EN
Summary
1 MANUAL SIMBOLOGY .....................................3
2 DEAR CUSTOMER..............................................3
3 CAUTIONS.........................................................4
4 SPARE PARTS.....................................................4
5 DISPOSAL ..........................................................4
6 PACKAGING AND HANDLING .......................4
6.1 PACKAGING.................................................4
6.2 STOVE HANDLING.........................................4
7 CHIMNEY FLUE ................................................5
7.1 INTRODUCTION.............................................5
7.2 CHIMNEY FLUE ..............................................5
7.3 TECHNICAL FEATURES ..................................6
7.4 HEIGHT-DEPRESSION.....................................7
7.5 MAINTENANCE .............................................7
7.6 CHIMNEY POT ...............................................7
7.7 CHIMNEY COMPONENTS.............................8
7.8 EXTERNAL AIR INLET ......................................8
7.9 CHIMNEY FLUE CONNECTION.....................9
7.10 EXAMPLES OF CORRECT INSTALLATION ... 10
8 FUEL ................................................................11
8.1 FUEL..............................................................11
9 INSTALLATION ................................................12
9.1 INTRODUCTION...........................................12
9.2 OVERALL DIMENSIONS (MARTINA-VANESSA-
ALESSIA MODELS) ..............................................13
9.3 OVERALL DIMENSIONS (SOLARIS MODEL).... 14
9.4 GENERAL INSTALLATION ............................15
9.5 S IDE PANEL ASSEMBLY (MARTINA MODELS) ... 15
9.6 ELECTRIC CONNECTION............................16
9.7 CONNECTION TO THE EXTERNAL THERMOSTAT .... 17
9.8 VENTILATION ...............................................17
10 USE .................................................................17
10.1 ATTENTION..................................................17
10.2 INTRODUCTION..........................................18
10.3 CONTROL PANEL.......................................18
10.4 IGNITION.....................................................19
10.5 FLAME ADJUSTMENT..................................19
10.6 FAILED IGNITION ........................................20
10.7 POWER FAILURE .........................................20
10.8 TEMPERATURE SETTING ..............................20
10.9 FUME TEMPERATURE ..................................20
10.10 SWITCHING OFF .......................................20
10.11 CLOCK SETTING .......................................21
10.12 WEEKLY SETTING.......................................21
10.13 FIRE EXTINGUISHING IN CASE OF FIRE....21
10.14 PELLET SUPPLY ..........................................22
10.15 REMOTE CONTROL (OPTIONAL).............22
11 SAFETY SYSTEM ..............................................23
11.1 INTRODUCTION..........................................23
11.2 ”ALAR NO RETE” ALARM...........................23
11.3 ”ALAR SOND” ALARM...............................23
11.4 ”ALAR HOT TEMP” ALARM........................23
11.5 ”ALAR NO FIRE” ALARM............................23
11.6 ”ALAR DEP” ALARM ..................................23
11.7 ”ALAR SIC” ALARM ...................................24
12 MAINTEINANCE ..............................................24
12.1 INTRODUCTION..........................................24
12.2
BURNING POT AND ASH TRAY CLEANING .... 24
12.3 HOPPER AND AUGER CLEANING ..........25
12.4 FUME CHAMBER CLEANING ...................25
12.5 FUME CONDUIT CLEANING ....................26
12.6 FUME FAN CLEANING .............................26
12.7 ROOM FAN CLEANING ...........................27
12.8 FUME PIPES ANNUAL CLEANING ............27
12.9 GENERAL CLEANING ...............................27
12.10 CLEANING OF PAINTED METAL PANELS ... 28
12.11 CLEANING OF CERAMIC AND STONE
PANELS ..............................................................28
12.12 GASKET REPLACEMENT .........................28
12.13 GLASS CLEANING ..................................28
13 IN CASE OF ANOMALY .................................29
13.1 ALARMS......................................................29
13.2 PROBLEM SOLVING ...................................32
14 TECHNICAL DATAS ........................................34
14.1 REPAIR INFORMATION...............................34
14.2 FEATURES ....................................................35

3
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
1 MANUAL SIMBOLOGY
• The icons with the stylized gures indicates whom the subject dealt in the paragraph is addressed to (between
the User and/or the Authorized Technician and/or the Specialized Stove-repairer).
• WARNING symbols indicates an important note.
USER
AUTHORISED TECHNICIAN
(ONLY to interpret or the Stove-manufacturer or the Authorized
Technician of Technical Assistance Service approved by the Stove-
manufacturer)
SPECIALIZED STOVE-REPAIRER
CAUTION:
READ CAREFULLY THE NOTE
CAUTION:
DANGER OR IRREVERSIBLE DAMAGE POSSIBILITY
2 DEAR CUSTOMER
• Our products are designed and manufactured in compliance with standards EN 13240 for wood stoves,
EN 14785 for pellet stoves, EN 13229 for re places, EN 12815 for wood cooker stoves, Dir.89/106/CEE for
manufacturing products, Re n.1935/2004 for materials and objects which are in contact with foods, Dir.
2006/95/CEE for low tension, Dir.2004/108/EC for Electromagnetic compatibility.
• Read carefully the instruction contained in this manual to obtain the best efciency.
• This instruction manual is an integral part of the product: make sure it is delivered with the appliance also in
case of sold to others. In case of loss please ask a copy to your local Technical Assistance Service.
• All local regulations, including those referring to national European standards, must be respected during
appliance installation.
In Italy biomass system installation below 35 kW must comply with MD 37/08. Every qualied
installer who own these requirements, has to issue the certicate of conformity for the
installed system (“system” means: stove + chimney + air inlet).
• According to (EU) No. 305/2011 regulation, the “ Declaration of Performance” is available online at the web
sites www.cadelsrl.com / www.free-point.it.

4MARTINA - VANESSA - ALESSIA - SOLARIS
EN
3 CAUTIONS
• All the pictures carried in this manual are only for indicative and explanatory purpose and could therefore
slightly differ from your appliance.
• The referring appliance is those you purchased.
• In case of doubts or difculties in the comprehension or for problems not described in this manual, please
promptly contact your distributor or installer.
• It is forbidden to modify the appliance without authorization.
4 SPARE PARTS
For each repair or adjustment which should be necessary, please contact the dealer where you purchased your
stove or your nearest Technical Assistance Service, specifying:
• Appliance model
• Serial number
• Type of problem
Use only original spare parts which you can nd at our Technical Assistance Services.
5 DISPOSAL
(European directive 2002/96/CE)
Fig. 1 - Disposal
This symbol on the product means that used electric and electronic products must not be mixed with domestic
waste.
For a proper disposal, recovery and/or recycling, please take this product to an authorized waste collection
points, where they will be accepted for free. For further instructions, please contact your local authority or your
nearest waste collection point. In case of wrong disposal of this waste material there could be applied penalties
as provided by national laws.
6 PACKAGING AND HANDLING
6.1 PACKAGING
• The packaging is made up of recyclable cardboard boxes according to RESY standards, recyclable
expanded polystyrene inserts and wooden pallets.
• All packaging materials can be re-used for a similar use or eventually discharged as waste assimilable to the
municipal solid ones, in accordance with current regulations.
• After having removed the packaging please assure you about the integrity of the product.
Packaging are not toys and could cause suffocation or strangulation and other health
hazards! People (childreen included) with reduced mobility, psycological deseases or
without experience and knowledge must be kept away from packaging. The stove is not a
toy, please see ATTENTION page 17.
6.2 STOVE HANDLING
Both whether the stove is packed or not it is necessary to observe the following instructions for handling and
transporting the stove from its sale point to its installation point and for any future movements:
• The stove must be handled with idoneous means paying attention to the existing safety regulations;
• do not turn the stove upside down and/or upset it on one side, but keep it in vertical position or as accorded
with the constructor instructions;
• if the stove is made up of ceramic, stone, glass or any particularly fragile material components, all must be
moved with the utmost care.

5
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
7 CHIMNEY FLUE
7.1 INTRODUCTION
This chapter about the Chimney Flue has been drawn up in cooperation with Assocosma (www.assocosma.org)
and is based on European Standards (EN 15287 - EN 13384 - EN 1856 - EN 1443 - UNI 10683:2012).
It provides instructions for a good and correct execution of the chimney ue but it does not absolutely replace
the current standards which the qualied manufacturer/installer should comply with.
Please check with your local authorities if exists any restrictive regulation which regards the
combustible air inlet, the fumes exhaust system, the chimney ue and the chimney pot.
The company declines any responsibility regarding the bad running of the stove if it is due to the use of a no
correctly dimensioned chimney ue which does not respect current regulations.
7.2 CHIMNEY FLUE
Fig. 2 - Chimney Flues
LEGEND Fig. 2 page 5
1Chimney ue with insulated stainless-steel pipes
2Chimney ue on the existing chimney
3Inspection plug
4Inspection door
5≥ 3,5 mt
• The chimney ue or chimney is of great importance for the correct running of the heating appliance.
• It is fundamental that the chimney ue is perfectly built and always maintained with a perfect efciency.
• The chimney ue must be sole (see Fig. 2 page 5) with insulated stainless-steel pipes (1) or installed on the
existing chimney ue (2).
• Both this solutions must be endowed with an inspection plug (3) and/or an inspection door (4).
It is forbidden to connect more pellet stoves or any other heating appliance to the same
chimney ue.

6MARTINA - VANESSA - ALESSIA - SOLARIS
EN
7.3 TECHNICAL FEATURES
Fig. 3 - Inclined roof
LEGEND Fig. 3 page 6
1Height over the ridge of the roof = 0,5 mt
2Roof inclination ≥ 10°
390°
4Measured distance at 90° from the roof surface = 1,3 mt
• The chimney ue must be sealed from fumes.
• It must have a vertical run without narrowing. It must be realized with fume and condensation resistant
materials with thermal insulation and able to last against usual mechanical stresses.
It must be insulated to avoid condensation and to reduce fume cooling effects.
• The stove must be spaced out from fuels or ammable materials with an air gap or with insulating materials.
Check the distance with the chimney manufacturer.
• The chimney entrance must be placed in the same room where the appliance is installed or otherwise in
the adjacent room and it must be provided with a solid and condensation collection chamber under the
entrance, accessible through the sealed metal gate.
• Auxiliary exhaust fans cannot be installed neither along the chimney nor on the chimney pot.
• The inner section of the chimney ue can be round (the best one) or square and the jointed sides must have
a minimum radius of 20 mm.
• The section dimension must be minimum Ø120 mm and maximum Ø180 mm.
• Made the efciency of the chimney ue overhauled by an expert stove-repairer and if necessary cover the
chimney ue with materials in compliance with current regulations.
• The ue system must be placed on the roof.
• The chimney ue must be provided CE in accordance with EN 1443 regulation. Please nd attached an
example of label:
Fig. 4 - Example of label

7
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
7.4 HEIGHT-DEPRESSION
The depression (draught) of a chimney ue depends also on its height. Check the depression with the values
provided at FEATURES page 35. Minimum height 3,5 meters.
7.5 MAINTENANCE
• The chimney ue must be cleaned, since the soot and unburnt oil deposits reduce its section so blocking the
draught. In great quantities they can are up.
• The fumes extraction pipes (fumes conduit + chimney ue + chimney pot) must always be cleaned, scrubbed
and checked by an expert stove-repairer, in compliance with current regulations, with the instructions of the
stove-manufacturer and the directives of your insurance company.
• In case of doubts, please follow the most restrictive regulations.
• Have your chimney ue and chimney pot checked and cleaned by an expert chimney sweep at least once
a week. The chimney sweep has to release a written declaration about the security of the system.
• Not cleaning compromise safety.
7.6 CHIMNEY POT
Fig. 5 - Anti-wind chimney pots
The chimney pot is important for the correct running of the heating appliance:
• We recommend using an anti-wind chimney pot, see Fig. 5 page 7.
• The hole width for fumes exhaust must be the double of the chimney ue width and tted in a way that the
fume exhaust is assured also in case of wind.
• It should prevent the inltration of rain, snow and animals.
• The outlet height in the atmosphere must be away from the reux area caused by the roof structure or by
obstacles laying nearby (see Fig. 3 page 6).

8MARTINA - VANESSA - ALESSIA - SOLARIS
EN
7.7 CHIMNEY COMPONENTS
Fig. 6 - Chimney components
LEGEND Fig. 6 page 8
1Chimney pot
2Fume outlet
3Chimney ue
4Termal insulation
5External wall
6Chimney union
7Fume pipe
8Heat generator
9Inspection door
10 T-union with inspection plug
7.8 EXTERNAL AIR INLET
Fig. 7 - Direct air inow Fig. 8 - Indirect air inow

9
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
LEGEND Fig. 7 page 8|Fig. 8 page 8
1Room to ventilate
2Adjacent room
3External air inlet
4Cleft under the door
• The room must be endowed with an external air recycling for a good climate in your ambient.
• The air inow from outside to the inner occurs directly, through an opening on the external wall of the room
(see Fig. 7 page 8); otherwise it occurs indirectly by air suction from rooms adjacent to the one to ventilate
(see Fig. 8 page 8).
• Bedrooms, garages, and store of ammable materials are excluded.
• The air inlet should have a total net surface of 80 sqcm2: the aforesaid surface is to widen if inside the room
there are other activated appliances (for example: electric ventilators for foul air suction, cooker hoods, other
stoves, etc...) which depress the environment.
• At switched on appliance it is necessary to check that the pressure fall between the room and the outside
does not exceed 4,0 Pa value: if necessary widen the air inlet (EN 13384).
• The air inlet must be realized at a height close to the oor with an external grid against birds. In such a way it
cannot be obstructed by any object.
• In case of installation with sealed-chamber the air inlet is not necessary.
7.9 CHIMNEY FLUE CONNECTION
Your pellet stove works through a fume draught forced by a fan. It is obligatory to check that all pipes are
realized in compliance with the following regulation on material selection: EN 1856-1, EN 1856-2 e UNI/TS 11278.
All must be effected by specialized personnel or companies as provided by UNI 10683:2012.
• The connection between the appliance and the chimney ue should be short in order to favor the draught
and to avoid condensation in the pipes.
• The fume conduit should be equivalent or longer than the outlet joint ones (Ø 80 mm).
• Some stove models are endowed with a lateral and/or back exhaust. Check that the unused exhaust is
sealed with the plug given with standard equipment.
SYSTEM TYPE Ø80 mm PIPE Ø100 mm PIPE
Minimum vertical length 1,5 mt 2 mt
Maximum length (with 1 union) 6,5 mt 10 mt
Maximum length (with 3 unions) 4,5 mt 8 mt
Maximum number of unions 3 3
Level section (minimum inclination 3%) 2 mt 2 mt
Installation at a height above 1200 m a.s.l. NO Obligatory
• Use a plate pipe for stoves of Ø80 mm or Ø100 mm depending on the type of system and with silicone gaskets.
• It is forbidden to use metal, bre cement or aluminium exible pipes.
• For change of direction it is obligatory always to use a union (with angle > 90°) with inspection plug which
enables an easy periodic cleaning of the pipes.
• Please assure you that after the cleaning the inspection plugs are sealed with its efcient gasket.
• It is forbidden to connect more appliances to the same fume conduit.
• It is forbidden to convey in the same fume conduit exhausts from overhanging cooker hoods.
• It is forbidden to exhaust ue gases directly from the wall towards the outside and closed spaces also at open
top.
• It is forbidden to connect any other appliance (wood stoves, cooker hoods, boilers, etc...).
• The fume conduit must be placed at a distance of minimum 500 mm from ammable or heat-susceptible
components.

10 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
7.10 EXAMPLES OF CORRECT INSTALLATION
Fig. 9 - Example 1
LEGEND Fig. 9 page 10
1Insulating material
2Reduction from Ø100 to Ø80 mm
3Inspection plug
4Minimum safety distance = 0,5 mt
• Chimney ue installation Ø120 mm with an enlarged drilling for pipe transit.
Fig. 10 - Example 2
LEGEND Fig. 10 page 10
1Insulating material
2Inspection plug
3Chimney inspection entrance
4Minimum safety distance = 0,5 mt
5Inclination ≥ 3°
6Level section ≤ 1 mt
• Old chimney ue with an inserted pipe of minimum Ø120 mm and with an external door which enables the
chimney cleaning.

11
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
Fig. 11 - Example 3
LEGEND Fig. 11 page 11
1Insulating material
2Inspection plug
3Minimum safety distance = 0,5 mt
• External chimney ue entirely made up of insulated stainless steel pipes, i.e. with double wall of minimum Ø120
mm: all must be rmly attached to the wall. For chimney against wind effects please (see Fig. 5 page 7).
• Ducting system through T-unions which enables an easy cleaning without disassembling the pipes.
We recommend to check with your chimney ue manufacturer the safety distances which
must be respected and the type of insulating material. The aforesaid regulations are valid
also for holes made on the wall (EN 13501 - EN 13063 - EN 1856 - EN 1806 - EN 15827).
8 FUEL
8.1 FUEL
• The type of fuel to use is only the pellets.
• Use top-quality pellets because they have inuence in the caloric value and in ash remains.
• Pellets features are: dimension Ø6-7mm (D06 Class), maximum lenght 40 mm, caloric value 5kWh/kg, humidity
≤ 10%, ash remains ≤ 0,7%, they must be correctly pressed and not much mealy, without sizing agents, resins
and other additives (it is advisable to use pellets in compliance with the regulation EN14961-2 type ENplus-A1).
• Not adequate pellets cause a bad combustion, a frequent burning pot obstruction and exhaust conduits
obstruction. Further it decreases the caloric value, soils the glass and increases consumptions and ash and
unburnt granules quantity.
Humid pellets cause a bad combustion and running, so please assure you that they are
stored in dry places and far at least one meter from the stove and/or any other source of
heat.
• It is advisable to try different type of pellets available on the market and to choose that which gives the best
performance.
• The use of bad quality pellets can damage the stove so that the warranty and manufacturer liability fall.
• Do not use the appliance as waste inceneretor.
• On all our product are used high-quality materials such as stainless-steel, steel, cast iron, etc... These materials,
before being sold on the market, are tested in laboratory, but despite this on the components which enable
the pellets ow (auger) there could exist minimum differences in the material used, in roughness and porosity,
which could generate usual variations in fuel transportation (pellets), causing a ame raising or drapping with

12 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
a possible switching off at lower powers.
• Depending on the type of pellets it could be necessary a parameters adjustment, please contact an
Authorized Assistance Service.
9 INSTALLATION
9.1 INTRODUCTION
• The assembly position must be chosen depending on environment, outlet, chimney ue.
• Check with local authorities if there are any restrictive regulations which regard the combustible air inlet,
room ventilation, fume exhaust system together with chimney ue and chimney pot.
• The manufacturer declines any responsibility in case of installation which are not in compliance with current
regulations, in case of a wrong room ventilation system, in case of an electric connection which is not in
compliance with regulations and in case of a wrong use of the appliance.
• The installation must be executed by an authorized technician, who must release to the user a declaration of
conformity of the system and will assume the whole responsibility on the nal installation and on the resulting
good running of the product.
• As equipment with the stove there is a testing and maintenance manual which must be periodically executed
by the installer.
• Check if there is the combustible air inlet.
• Check the probable presence of other stoves or appliances which could depress the room (see EXTERNAL
AIR INLET page 8).
• Check at switched on stove if there is the presence of CO in the room.
• Check if the chimney has the necessary draught.
• Check if during the fume passage all has been executed in safety (probable fume losses and distances from
ammable materials, etc.…).
• The installation of the appliance must enable an easy access for appliance, fume exhaust pipes and chimney
ue cleaning.
• The installation must enable en easy access to the electric connection plug (see ELECTRIC CONNECTION
page 16).
• It is forbidden to install the stove in bedrooms, bathrooms and in rooms used for storing combustible materials
and in one-room ats.
• The installation in one-room ats is allowed if they are in sealed chamber.
• In any case the stove must not be installed in rooms where it can get in touch with water or water splashes
because this can cause burn hazards and short-circuit.
• To install more appliances, the external air inlet must be correctly dimensioned (see EXTERNAL AIR INLET page
8).

13
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
9.2 OVERALL DIMENSIONS (MARTINA-VANESSA-ALESSIA MODELS)
Fig. 12 - General dimensions
LEGEND Fig. 12 page 13
157 cm
298 cm
352 cm
438,5 cm
536,7 cm
629 cm
728 cm
8Hole combustion air inlet d.4 cm
9Exhaust fumes d.8 cm

14 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
9.3 OVERALL DIMENSIONS (SOLARIS MODEL)
Fig. 13 - General dimensions
LEGEND Fig. 13 page 14
152,6 cm
2121,6 cm
353,6 cm
438,5 cm
536,7 cm
629 cm
728 cm
8Hole combustion air inlet d.4 cm
9Exhaust fumes d.8 cm

15
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
9.4 GENERAL INSTALLATION
Fig. 14 - General installation
LEGEND Fig. 14 page 15
1Stove
2Minimum lateral distance = 300 mm
3Minimum rear distance = 200 mm
4Minimum front distance = 1000 mm
• Please check that the oor has an adequate load capacity. If the existing one does not satisfy this requirement,
appropriate measure should be provided (for example a plate for distributing the load).
• It is obligatory to install the stove away from walls and/or pieces of furniture, with a minimum air ow of 300
mm on the sides and 200 mm on the back, to enable an ecient appliance cooling and a good distribution
of heat in the room (see Fig. 14 page 15).
• For safety re regulations the distances from ammable or sensible to heat objects (sofas, pieces of furniture,
wooden covering, etc...) must be respected, has described in Fig. 14 page 15.
• If there are highly ammable objects (curtains, tted carpet, etc...), all these distances must be further
increased with 1 meter.
• If the walls are made up of ammable materials, check the safety distances (see Fig. 14 page 15).
• At maximum power check that the wall temperature does not ever exceed 80°C. If it would be necessary
please install a re resistant plate on the concerned walls.
• In some countries also masonring load-bearing walls are considered ammable.
9.5 SIDE PANEL ASSEMBLY (MARTINA MODELS)
Fig. 15 - Upper screws removal Fig. 16 - Backward screws removal
• Remove the top cover: unscrew the 2 upper screws and the 3 backward screws (see Fig. 15 page 15 and
Fig. 16 page 15).

16 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
Fig. 17 - Bend the supports
• Slightly bend the supports in order for them to compensate any movement in the metal/majolica/stone
panels (see Fig. 17 page 16).
Fig. 18 - Side panel insertion Fig. 19 - Ceramic panel insertion
• Insert from on high the metal side panels on the appropriate guides getting it slightly course all the way (see
Fig. 18 page 16).
• Insert from on high the ceramic side panels on the appropriate guides getting it slightly course all the way
(see Fig. 19 page 16).
• Recompose all.
9.6 ELECTRIC CONNECTION
Warning: the appliance must be installed by an authorized technician!
• The electric connection occurs through a cable with plug put in an electric socket which is able to support
charge and tension specic of every model, as described in the technical datas table (see FEATURES page
35).
• The plug must be easily accessible when the appliance is installed.
The cable must not get in touch with the fume exhaust pipe and nor with every other part
of the stove.

17
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
• Please further assure you that your network is endowed with an efcient earth connection: if it does not exist
or if it is not efcient, please endow you with one in compliance with the law.
• Do not use extension cables.
• If the feeder cable is damaged, it must be replaced by an authorized technician.
• When the stove is not going to be used for a long period of time, it advisable to remove the plug from the
socket on the wall.
9.7 CONNECTION TO THE EXTERNAL THERMOSTAT
The stove works through a thermostat probe placed in its inner. If you desire, the stove can be connected to an
external room thermostat. This operation must be executed by an authorized technician.
For connection see :
• external thermostat: set up a temperature which is round 7°C.
• External chronothermostat: set up a temperature which is round 7°C and desable the chrono functions from
the menu 03-01.
9.8 VENTILATION
• The stove is endowed with a ventilation system.
• The air blown from fans keeps the appliance at a low temperature range in order to avoid high stresses to the
materials which make it up.
Fig. 20 - Do not cover air slits
Do not cover the hot air outlet slits with any object to avoid stove’s overheating!
The stove is not suitable for food cooking.
10 USE
10.1 ATTENTION
This appliance must not be used by people (childreen included) with reduced mobility,
psycological deseases or without experience and knowledge except in case of supervision
or instruction about the use of the appliance by people responsible for their safety.
Childreen must be constantly overseen in order to assure that they do not play with the
appliance.

18 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
The stove is provided with a hand rejector: this rejector can be removed exclusively by the
stove manufacturer or by the Technical Assistance Service.
During its running, the stove reaches high temperatures: keep away childreen and animals
and for your safety please use appropriate reproof devices, such as heat-protecting gloves.
10.2 INTRODUCTION
To have the best performance with the lowest consumption please follow the here descripted instructions.
• The lightning of the pellets occurs very easily if the installation is correct and if the chimney ue is efcient.
• Switch on the stove at Power 1 for at least 2 hours in order to enable the materials which make up the boiler
and the replace to adjust the inner springing stress.
• Oily plant waste and lacquers can cause smells and smoke during the rst working hours: it is advisable to
ventilate the room because they could be noxious to people and animals.
• By using the stove the varnish inside the combustion chamber could be subjected to alterations. This
occurrence can be attributed to different reasons: an excessive stove overheating, the presence of chemical
agents in bad quality pellets, bad chimney draught, etc. Therefore varnish endurance in the combustion
chamber cannot be guarantee.
Set values from 1 to 5 are dened by the manufacturer and they can be changed only by
an authorized technician.
Do not use ammable liquids during the ignition (alcool, petrol, oil, etc...).
10.3 CONTROL PANEL
PANEL ELEMENT DESCRIZIONE
P1 e P2: when you are in set temperature mode the termostat values increase or
decrease from min. 6°C to max. 40°C. Keeping pressed P2 you check the fume
temperature at outlet. Both have programming functions.
P3: enable to have access to temperature set and to User and Technician parameters
menu.
P4: ignition and shut down, unblocking from probable alarms and exit from
programming.
P5 e P6: increase and decrease the caloric power from 1 to 5.
Hourly programming: acitvated.
Auger: activated.
Remote control data reception

19
MARTINA - VANESSA - ALESSIA - SOLARIS
EN
PANEL ELEMENT DESCRIZIONE
Thermostat: activated
Flashing: during the temperature set or when inside the menu
Display A During the starting up shows the mother board state. During the running shows the
heating power. During the setting shows the parameters in modication
Display B
During the starting up shows the mother board state. During the working phase shows
the temperature set by the user. During parameters modication shows the value of
the parameter in modication.
Fig. 21 - LED control display
LEGEND Fig. 21 page 19
1Display A: state, power (name of the parameter)
2Display B: state, time, temperature (size value)
10.4 IGNITION
We remind you that the rst ignition must be executed by authorized and skilled technical personnel who checks
that all is installed in compliance with current regulations and veries stove’s efciency.
• If inside the combustion chamber there are booklets, manuals, etc.… please remove them.
• Check that the door is correctly closed.
• Check that the plug is correctly put into the electric socket.
• Before switching the stove on, please assure you that the burning pot is cleaned.
• To start the stove up, keep pressed P4 key for an instant till the display shows “FAN CAND”: the preheating
of the ignition plug starts. After 2 minutes about, the display will show “LOAD WOOD”: now the auger load
the pellet and the preheating of the ignition plug continues. When the temperature is suffuciently high (after
about 7-10 minutes), the ignition is considered as occured and the display shows “FIRE ON”.
• When the “FIRE ON” phase has nished, the control unit enters in working mode and the selected caloric
power and the ambient temperature will be shown. It is in this phase that P5 and P6 are useful for regulating
the stove power from 1 to 5.
10.5 FLAME ADJUSTMENT
It is possible to regulate the ame thanks to the PVC lid applied to the combustion air inlet pipe which stands on
the back side of the stove.
• If the ame is weak and the glass tends to blackens, this means that the combustion is not correct: it is
necessary to open the regulator (see Fig. 22 page 20).

20 MARTINA - VANESSA - ALESSIA - SOLARIS
EN
Fig. 22 - Regulator
10.6 FAILED IGNITION
If the pellets do not burn, the failed ignition will be indicated by the alarm “ALAR NO FIRE”
• If the room temperature is lower than 10°C, the plug is not able to bear the ignition stage. To support it please
insert some pellets in the burning pot and a piece of burning relighter igniter material on the pellets (for
example relighters cubes).
After a failed ignition the burning pot must be empty from the amassed pellets, before
starting the stove up again.
• Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difcult and create
dense white smoke which is harmful to health and can cause explosions on the combustion chamber. It is
therefore necessary not to stand in front of the stove during ignition stage if dense white smoke is present.
If after some months the ame appears weak and/or orange colored or the glass tends
to blackens and the burning pot to become encrusted, clean the stove, clean the fume
conduit and the chimney ue.
10.7 POWER FAILURE
• After a black-out, after its reactivation, the stove signals on the display “ALAR NO RETE”.
• The stove starts the switching off phase up by activating the fume fan which for 15 minutes will arrange for the
fume remainings expulsion.
• Reset the error with P4 key.
• Clean the burning pot and start the stove up again with P4 key.
10.8 TEMPERATURE SETTING
• To modify the ambient temperature it is sufcient to keep pressed P3 key and at the same time select the
temperature with P1 and P2 keys.
• The selected temperature and the ambient temperature are shown on the Display B.
• If the ambient temperature value exceeds the selected limit, the caloric power falls at the minimum till the
threshold return at the preset value, then the display shows “RIS”.
10.9 FUME TEMPERATURE
To check fume temperature at the exhaust outlet, it is sufcient to keep pressed P1 key.
10.10 SWITCHING OFF
To switch the stove off, keep pressed P4 key: the display A shows “OFF”. After about 15-20 minutes also the fume
fan switches off (this occurs always wheter the stove is hot or cold).