Cadet FW051 User manual

1'(.#61%(75('9,6+$0;/1'(.+($6(4
Any of the following models may be replaced using the FW conversion kit:
FW051, RW051, FW052, RW052, FW071, RW071, FW751, RW071, FW752, RW752
FW072, RW072, FW101, RW101, FW102, RW102, FW121, RW121, FW122, RW122
FW151, RW151, FW152, RW152, FW202, RW202, FW252, RW252, FW302, RW302
*The above models may be controlled by either a built-in thermostat or a wall mount thermostat.
(0(4$.$)(6;0)14/$6,10
 !
3 crews
2 pring Nuts
2 Lead Wires
1 Replacement Grill Label
2 Mounting crews
1 Conversion Plate
3 Lock Tooth Washers
1 Instruction Guide
!
Phillips crewdriver
traight crewdriver
#
7406+((.(&64,&$.219(41))$66+(
(.(&64,&$. 2$0(. %1$4' &,4&7,6
%4($-(4 14 )75( %1: $0' .1&- 14
6$* 6+( 2$0(. %1$4' '114 61
24(8(0651/(10()41/6740,0*10
219(4 9+,.( ;17 $4( 914-,0* 10
6+(+($6(4 $,.74(61'151&17.'
4(57.6 ,0 5(4,175 (.(&64,&$. 5+1&-
%7405142155,%.('($6+
 #
,5-1)),4(142412(46;'$/$*(
< replace your heater with a higher wattage assembly.
Replace your heater with the same voltage and wattage that
was originally installed. Replacing it with a higher wattage
heater could result in an overloaded electrical circuit in your
home, which could result in a fire and serious property damage.
Replacing with a lower wattage heater may cause insufficient
heat and result in increased energy costs.
 All electrical work and materials must comply with the National
Electric Code (NEC), the Occupational afety and Health Act
(O HA), and all state and local codes.
 When installing the heater conversion kit, be certain the FW
heater being replaced was wired correctly to all electrical codes
and the supply wiring is the correct size and in good condition.
If not, it must be replaced before proceeding.
 If you need to install a new circuit or need additional wiring
information, consult a qualified electrician.
 Protect electrical supply from kinks, sharp objects, oil, grease,
hot surfaces or chemicals.
($674(5<<(0(),65
•Converts discontinued FW eries wall can
to newer Com-Pak or Com-Pak Max
•UL Listed for installation of Com-Pak
model into FW wall can
•No sheetrock construction necessary -
saves time and money
•Vertical or horizontal installation
);17$4(70&1/)146$%.(914-,0*9,6+(.(&64,&$.$22.,$0&(570$%.(61)1..196+(5(*7,'(.,0(5
14'1016+$8(6+(0(&(55$4;(37,2/(06&1057.6$.,&(05('(.(&64,&,$0
vertical installation shown
1
"  ! 
cadetheat.com Tel: [phone] P.O. Box 1675 Vanco ver, WA 98668-1675
©2014 Cadet Printed in U. .A. 12/14 #720027
FWAP Conversion Kit
Installation Instructions
http://www.cadetheat.com/products/wall-heaters/com-pak

pring Nut
(/18,0*.'#($6(4
1. Pull off thermostat knob (if applicable) and remove top and bottom grill
screws to remove grill.
2. Remove screw on bottom center of heater assembly.
3. Unscrew insulated wire connectors and separate supply wires from
heater wires.
4. Remove the heater assembly by pushing up in the direction of the fan
and pulling unit out of wall can.
056$..,0*108(45,10,6
1. crew top and bottom screws and washers about halfway into the wall
can with the half-moon tabs facing out ( ee Figure 1).
2. Push plate down into position.
3. Tighten the screws. NOTE: tar washers MU T be located between
the screw head and painted surface of the conversion plate.
4. Install one spring nut at the top and one at the bottom ( ee Figure 2).
056$..,0*(9($6(455(/%.;
16( If FW heater was wired with the supply circuit entering the wall can
from the top, it may be necessary to add 8 inches of lead wire to each of
the supply lines before proceeding with installation of new heater.
1. +(1/$-4(37,4(5$6+(4/156$66112(4$6( Please follow
wiring instructions supplied with either your built-in thermostat kit
or wall mount thermostat and your new heater. If new heater has
a built-in thermostat, the two mounting screws must be removed
and reattached to the bottom of the FWAP.
2. Once wiring is complete, slide heater assembly into half-moon tabs
located on bottom of conversion plate. Use screw supplied with heater
assembly and star washer supplied with kit to attach heater to
conversion plate.
3. If using original grill, turn the grill upside down ( ee Figure 3) and
install using two new #10 screws. If there is a built-in thermostat,
be sure it is at the bottom.
4. Affix new label (provided) on inverted grill. It is not necessary to
remove the old label. If using a built-in thermostat, cut thermostat
shaft hole out of new label.
2(4$6,1005647&6,105
1. Once installation is complete and power has been restored, turn the
thermostat knob fully clockwise.
2. When the room reaches your comfort level, turn the thermostat knob
counterclockwise until the heater turns off. The heater will
auto mat ically cycle around this preset temperature.
3. To reduce the room temperature, turn the knob counterclockwise.
To increase the room tempera ture, turn the knob clockwise.
#05647&6,105$&-,'(
pring Nut
+$.)
/110
6$%5
,*74(
,*74(
,*74(
©2014 Cadet Printed in U. .A. 12/14 #720027