Cairox S-TOUCH User manual

user manual

2 3
CAIROX
Name Description
Power supply 24 VDC
Way of control touch screen
Temperature adjustment range +5 ÷ +45°C
Operating temperature range -10 ÷ +60°C
Temperature sensor built-in
Protection degree IP20
Installation on the wall
Casing ABS plastic, RAL 9003
Max. number of connected
units 31
Dimensions (HxWxD) 130 x 115 x 35 mm
S-TOUCH intelligent controller with touch screen enables
control all air curtains SOLANO.
Each unit must have its own individual address in S-ECM
control module.
Table of contents Technical data
General information
Technical data................................................................................................2
General information .................................................................................2
Installation........................................................................................................3
Navigation........................................................................................................3
First run...............................................................................................................4
Main screen .....................................................................................................6
Main menu ................................................................................................ 6
Time...............................................................................................................7
Date................................................................................................................7
Calendar......................................................................................................7
Language.................................................................................................10
Integrated units...................................................................................11
Reset...........................................................................................................11
Leading sensor.....................................................................................12
Control lock............................................................................................12
System information........................................................................... 13
BMS..............................................................................................................13
SOLANO air curtains ............................................................................14
SOLANO COMBI air curtain-fan heater combo units...16
Alarms...............................................................................................................20
SW
1
0
1 2 4 8 16 Y1

3
CAIROX
General information
S-TOUCH controller has a built-in sensor for measuring
air temperature in the room. To ensure proper measure-
ments, the controller should be installed at a height of
approx. 1.5 m above the ground in a place with good air
circulation. Do not place it near heat sources, lighting, air
inlets, windows and door openings, etc.
If temperature sensor was chosen in a S-TOUCH menu
as„installed in unit” (p.32), S-TOUCH controller can be
mounted out of area i.e. technical room.
BMS
GND
B A
SW1
RESET
SW1
T120
T-box
GND
B A VCC
max. 50 m
VCC
GND
A
T- box
B
DRV
min. LICY 4x0,5 mm2 screenedy
A and B braided wire pair
In the case, when S-TOUCH in BMS network is the last
device, SW1 switch should be set in T120 position.
return to previous screen with
save of changes
change of parameter value
change of unit group
return to previous screen without
save of changes
menu navigation
Installation
Navigation
1
3
2

4 5
CAIROX
First run
active language
Searching of connected units
Selection of language Setting of date
Setting of time
DevicesTime
DataLanguage
13PM
August
FR

5
CAIROX
Verify if all units have been
found. If not, check:
• correct connection of communication signal A-A, B-B,
• power supply of the unit,
• correct setting of addresses, each unit must have
dierent address,
• if in the last unit dip-switch SW2 is set in T120 position.
Setting of desired temperature.
12:55PM
Devices
SOLAN
Set individual addrress in S-ECM module for each unit.
DRV address
1
2
3
...
31
1 2 4 8 16 Y1

6 7
CAIROX
Main screen Main menu
long press turn on/off of the controller
long press main menu
short press units menu
alarms
setting of desired temperature
time
setting
date
setting
selection of
leading sensor
calendar
controller lock
language selection
integrated units
hardware
version
restore factory settings
BMS settings
desired temperature
measured temperature
date, time
settings lock active
BMS mode active
calendar active
calendar active – settings forced
Enter to the menu after entering the
password: 2014
long
press
4:05PM
12:55PM General settings
FR

7
CAIROX
Time Calendar
Date
Setting of time
Setting of date
• For each day you can set up to 20 on/o events,
• Start time of new event is also the end time of previous
event,
• For each event you can set any temperature for units, in
the range of 5 – 45oC,
• Events for each day can be set individually or can be
copied from day, which was already set.
Activation of calendar is signalized on main screen via
following icons:
There were ad hoc set other parameters than
the settings programmed in the calendar:
• desired temperature,
• system were OFF and was turned on (to turn
on the system press and hold for 2 s the
calendar icon on main screen),
• system were ON and was turned o (to turn
o the system press and hold for 2 s the
calendar icon on main screen).
Ad hoc settings stays as long as time of current
event in calendar. With start of next event,
units will operate according to programmed
settings.
calendar active – SYSTEM ON
calendar active – SYSTEM OFF
calendar active – settings forced.
Date
Time
13PM
August

8 9
CAIROX
Calendar – Adding the ON event
In given example SYSTEM will be turned on at 6:15 and
the units will maintain temp. 12oC.
SYSTEM WILL OPERATE USING CURRENT SETTINGS UNTIL
NEW EVENT WILL BE SET.
activation / deactivation of calendar
moving to the next day
adding the event
event – system ON
copying events on the following days
event – system OFF
removing the events
Calendar
Weekly programer
New task
Weekly programer
Monday
4:15AM
7:00AM
11:30PM
4:00PM 6:00PM Tue
7:00AM
9:00AM

9
CAIROX
Calendar – Copying events
day from which events will be copied
day selected for copying events from PN day
day with already programmed operation
schedule – you can also copy here the events
from PN day
day without programmed operation schedule
Calendar – Adding the OFF event
In given example units will be turned o at 16:00.
SYSTEM WILL BE TURNED OFF UNTIL THE NEXT EVENT,
ACCORDING TO CALENDAR SETTINGS.
Weekly programer
Copy
Weekly programer
New task
Mon ThuTue
SatFr
4:00PM Wed
Sun

10 11
CAIROX
Calendar – Removing events Language
events selected
to remove
conrmation of
events removal active language
Language
Weekly programer
Delete task
7:00AM
8:15PM
9:15AM9:00AM
10:00PM
4:00PM 4:15PM 7:00PM
FR