Caldwell OMNI DRIVE User manual

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 1:
Start with the OMNI DRIVE™ Engine in the closed position (shown). Place
the OMNI DRIVE™ Engine on sill surface ensuring it is sitting flat. Align
engine holes with prefabricated holes closet to the center of the sill. Insert
the #10 x ½” undercut mounting screw(s). Using a Phillips head screwdriver
fasten the Engine to the frame.
Step 2:
Cover Engine holes with the two caps
provided.
CSL-
00016Surface Mount Installation 11/30/18
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 3:
Slide the left lock bar through the left
track. Drop over the pin on the Engine.
Step 4:
Slide the track towards the engine.
Step 5:
Align the prefabricated hole with the hole in
track. Insert the #10 x ½” undercut
mounting screw(s). Using a Phillips head
screwdriver fasten the track to the frame.
Step 6:
Slide the right lock bar to the left (opening
the OMNI DRIVE™). Slide the left lock bar
through the left track. Drop over the pin
on the Engine.
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 7:
Slide the track towards the engine.
Step 9:
Slide the left lock bar to the right (closing the
OMNI DRIVE™). Align the prefabricated hole
with the hole in left track. Insert the #10 x
½” undercut mounting screw(s). Using a
Phillips head screwdriver fasten the track to
the frame.
Step 8:
Align the prefabricated hole with the hole in
right track. Insert the #10 x ½” undercut
mounting screw(s). Using a Phillips head
screwdriver fasten the track to the frame.
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016 Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 10:
Slide lock bars left and right to ensure the
OMNI DRIVE™ operates smoothly free of
and obstruction. Typically wrong screws
used or proud screw heads cause drag.
Step 11:
Apply gasket on the Handle Housing, by
exposing the adhesive strip and aligning
the holes.
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 12:
With the handle in the closed position
(to the right from interior) slide into slot.
Insert the 8-32 x ½” socket head cap
screws, from inside the frame via
predrilled holes. Use a 9/64” hex wrench
to tighten to a snug torque.
Step 13:
Rotate handle 180 degrees to the open
position so the Engine Arm Receiver is
angle outward.
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016 Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 14:
Attach vent track to vent with one screw.
Clearance holes on track accommodate #10
Screws (screws not provided)
Step 16:
Slide vent arm until the arm is in position
resting on the OMNI DRIVE™ engine arm
receiver as shown. Fasten the track using the
remaining hole.
Step 15:
Insert vent arm into the vent track.
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Step 17:
Insert the eccentric cam into place ace
shown & place the vent arm on top of it.
Step 18:
Using a 5/32” security hex driver (CMC #
422) insert the two 10-32 x ¼” security
button head cap screws as shown & tighten
to a snug torque
Step 19:
INSTALLATION COMPLETED
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Handle returns to zero & vent does not close completely.
NEED TO INCREASE CLOSURE
(Pull Vent In)
Vent will close & handle does not return to zero.
NEED TO DECREASE CLOSURE
(Push Vent Out)
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
CSL-
00016Surface Mount Installation 11/30/18

OMNI DRIVE™Installation Instructions
(Surface Mount)
Caldwell Manufacturing Company North America, LLC
Phone: [phone] Web: www.caldwellmfgco.com
Fax: [phone] Email: [e-mail]
To Start
Loosen the two 10-32 x ¼” security head cap
screws using a 5/32” security hex driver.
To INCREASE Closure (Pull Vent In) To DECREASE Closure (Push Vent Out)
Insert the 5/32” security hex driver into the
eccentric cam and rotate counter clockwise.
Tighten the two 10-32 x ¼” security head cap
screws using a 5/32” security hex driver.
Insert the 5/32” security hex driver into the
eccentric cam and rotate clockwise. Tighten
the two 10-32 x ¼” security head cap screws
using a 5/32” security hex driver.
CSL-
00016Surface Mount Installation 11/30/18