Caliber HSG 401i User manual

2
Congratulations on purchasing this HSG 401i. You can now listen to FM radio and
play music from your iPhone, iPod or iPad.
Please read the warning section on page 13 carefully before using your HSG 401i.
Welcome
HSG 401i Remote Control
AC/DC Power Adapter
You should have
You may also need
• 3.5 mm Line In cable

3
08
Your HSG 401i
Setup
Everyday use
Advanced use
Troubleshooting
Maintenance
Warnings
Technical specifications
Contents
01
02
03
04
05
06
07

4
LED display
DC POWER
input
Your HSG 401i
01
FM aerial
cable
AUX
input
POWER
switch
PRESET
button
VOL+
button
SOURCE
button
SKIP FWD
button
PLAY/PAUSE
button
VOL-
button
STANDBY
button
SKIP BACK
button
iPhone/iPod/iPad
DOCK

5
STANDBY button
SOURCE button
TIME SET button
ALARM button
VOL+ button
MUTE button
SKIP BACK button
PRESET button
PLAY/PAUSE button
DOWN button
SELECT button
UP button
MENU button
SKIP FWD button
DIMMER button
REPEAT button
SCAN button
SNOOZE button
SLEEP button
VOL- button

6
Setting up your Dock
1 Plug one end of the included AC/DC
cable into the DC POWER input
on the back of your Curve iPad Dock.
Plug the other end into a standard
power socket.
2 Switch the power to ON on the
rear of the unit.
3 Extend the FM aerial cable
on the back of the unit.
Note:
If not using the unit for a long time,
disconnect the AC/DC adaptor from
the wall outlet.
1
Note:
Aerial positioning
You may need to reposition the aerial for
optimal reception. The best position is
dependent on the station and the strength
of the signal.
2
3
Setup
02

7
Battery replacement
Note:
Remove the plastic
sheet before
operating the
remote control.
The remote control battery
1
2
The remote control comes fitted with a 3V
battery. The battery is already inserted into
the remote control and blocked by
a plastic sheet.
When the battery becomes weak, the
operating distance of theremote control
is greatly reduced and you will needto
replace it as described below.
1 Slide the battery draw out from the
bottom of the remote. You will need
to release the clip at the side of the
draw. The draw will slide out as shown.
2 Remove the old battery, then insert a
new one with the same or equivalent
type, make sure the positive (+) side
is facing upwards as shown.
3 Slide the draw closed, it will click
into place.

8
Everyday use
Using the FM radio
Turn on yourCurveiPad Dock by pressing
the STANDBY button. An FM frequency
will be displayed onthe LEDdisplay.
1You can select the desired frequency
manually by pressing and holding the
or button or by pressing the
SCAN button.
2Fine tuning can be performed by
pressing the or button once,
and repeating until the desired
frequency is found.
03
Tip:
Where a button that appears on both the
unit and the remote control is referenced in
this guide you can use either button to
perform that function.
Setting the time
After plugging your Curve iPad Dock into a
mains power socket, your Curve iPad Dock
will be in STANDBYmode.
1Press and hold the TIME SET button
on the remotecontrol to set the time
2Press the and buttons to set the
hour. Confirm by pressing the TIME
SET button.
3The minute will flash, usethe
and buttons tosetthe minute
and confirm by pressing the TIME
SET button.

12
Problem What to do
iPhone/iPod/iPad
System does not
turn on
Make sure AC/DC power adaptor is secure in the outlet and the outlet has power.
iPod/iPhone/iPad in
place but unit won’t
play
Make sure that your iPhone/iPod/iPad is working properly before docking into the unit.
Please refer to your iPhone/iPod/iPad manual for details.
Make sure the volume is not set to the minimum level.
Pause mode is activated.
iPhone/iPod/iPad does
not dock properly
or does not install
properly
Remove your iPhone/iPod/iPad from the dock and check for obstructions on the connectors
in the dock and on your iPhone/iPod/iPad.
Radio
Poor FM reception Make sure FM aerial cable is fully extended and adjusted for optimum reception.
Electrical interference in your home can cause poor reception, move the unit away from
those areas (especially those near motors and transformers).
1 Do not use harsh or abrasive cleaning
agents or solvents.
2 Polish the product with soft cloth.
3 Do not attempt to disassemble
your product.
4 Do not paint your product.
5 Do not drop, throw or try to bend
your product.
6 Do not expose your product to open
flames or lit tobacco products.
Troubleshooting
05
Maintenance
06

13
This product was designed and manufactured
to meet strict quality and safety standards.
There are, however, some operation
precautions that you should be awareof:
• Read all warnings.
Follow all instructions.
• Check the mains voltage stated on the
mains adaptor rating platecorresponds
to the local electricity supply, if it doesn’t,
return the product to the store where
you bought it.
• Unwind and straighten the power
cord before use.
• Place the product on a
flat surface. Allow space around the
product to ensure enough ventilation.
• To completely disconnect this product
from the mains, disconnect the plug
from the wall socket outlet. The mains
plugis used to completely interrupt
the power supply to the unit and
must be easily operable by the user.
• Remove the plug from the outlet, when
the product is unused for a long period
of time and during thunderstorms.
• Clean only with a dry cloth, unplug
the outlet before cleaning. Do not
use aggressive cleaners as these will
damage the surface.
• Only use attachments/accessories
specified by the manufacturers.
• Do not locate the appliance in the
vicinity of a heat source or in direct
sunlight. Do not place a naked flame
source on or near this product.
• Do not attempt to open the cabinet
or remove any covers. If thepower
adaptor or itslead becomes damaged,
it must bereplaced with an adaptor
of the same type and rating.
• Repairs must only be performed by
the manufacturer or its service agent
or similarly qualified person.
• Do not immerse the main unit,
the power adapter or any accessories
in water or any other liquid.
• Do not expose this product to dripping
or splashing or stand any vessel
containing liquid on or near this product.
• Replace batteries with the same
or equivalent type.
•Do not cover the product or this will
impede ventilation.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warnings 07