Calspas Spa Surrounds User manual

LTR20091033, Rev. A
12/16/08

CONTACT INFORMATION
For customer service, please contact
your authorized dealer immediately. If
you need additional information and/
or assistance, please contact:
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
Toll Free: 1-800-CAL-SPAS
Fax: [phone]
Read This First!
Carefully read and follow all safety instructions.
When installing and assembling your surround
package, it is recommended that two or more
people be involved.
Do not use the unit during an electrical storm.
Do not climb on top of the surround package. While
the surround package is made out of high-quality
material and is extremely durable, it is not meant
to support weight. In addition, falling off of the
surround package while climbing on it can result in
serious injury or death.
Do not attempt any repair without consulting the
manufacturer rst. Unauthorized repairs will void
the manufacturer’s warranty (within the rst 90
days).
Copyright 2008-2009 LMS, Inc. All rights reserved. Duplication without
written consent is strictly prohibited.
Cal Spas™ and Cal Enclosures™ are registered trademarks.
Due to continuous improvement programs, all models, operation, and/or
specications are subject to change without prior notice.
LTR20091033, Rev. A
12/16/08
Assembly ........................1
Tools and Materials ....................1
Step Assembly ........................1
Planter Assembly......................5
Bar Stool Assembly ....................6
Bar Assembly and Installation ...........7
Bench Assembly......................13
Panel Assembly ......................15
Maintenance ....................17
Warranty Information.............18

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
1
Whether you assemble your surround package yourself or hire someone to do it, your new surround package
needs to be assembled in a specic order. Our Cal Enclosures professionals have determined through their
experience that this is the easiest way to assemble your surround package.
Tools and Materials
Utility knife 25’ tape measure Cordless drill
100’ extension cord Electric drill Phillips-head drill tips
1/8” pilot hole drill bit 9/16” socket Slotted-head drill tips
Sandpaper (various grades) Redwood stain Wood putty
Gray wash stain Rags 1/2” ratchet and impact drill
1/2” carbide drill bit (masonry bit)
Step Assembly
Two Tier, 30” Step
Stand the legs up at 30” apart. Place the upper step on top of the upper section of the step.1.
To attach the step, screw in 4 screws (2 at each rear corner): 1 into the step leg and 1 into the step itself.2.
Place the lower step on the lower section of the step.3.
To attach the step, screw in 4 screws (2 on each on the outside of the step). Use the toe-in method on both 4. sides, as shown.
Assembly

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
2
Package R Step Assembly

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
3
Package D, E, and I Step Assembly

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
4
Cal Select Step Assembly

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
5
Planter Assembly

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
6
Bar Stool Assembly
Attach the bar stool legs to support the brace using the provided 2 ½” screws. There will be a total of 121. screws.
Place the bar stool seat on a at surface. (Make sure the nish side is on the ground.) Attach the leg 2. assembly using four 2 ½” screws.

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
7
Bar Assembly and Installation
Package B and M

2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www.ca l spas.com
8
Package C, J, and N