Cam Scan CS-EXP6800 Installation instructions

Explosion proof PTZ Camera
P/N :
PRINTED IN KOREA
Distributed by
INSTALLATION / OPERATING MANUAL
- Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
- The design and specifications are subject to be changed without prior notice to improve
product’s quality.

02
Explosion proof PTZ Camera User’s Guide
03
Explosion proof PTZ Camera User’s Guide
1. 1 Important Safety Instruction
• Read these instructions.
• Pay attention on all the warnings.
• Follow all instructions.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not dissemble or insert foreign objects.
• Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
• Do not aim the camera at the sun or any other strong light source.
• Do not install the camera in intermittent lighting environments.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Installation should be done only by qualified personnel and conform to all local codes.
• Installation should be done in a place strong enough to hold it.
• Use only installation methods and materials capable of supporting four times the maximum specified load.
• To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
• These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
• Only use replacement parts recommended by manufacturer.
1. PRECAUTIONS
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
24p.
29p.
40p.
40p.
41p.
42p.
43p.
1. PRECAUTIONS
1. 1 Important Safety Instruction ...................................................................................
2. GETTING STARTED
2. 1 Descriptions ..........................................................................................................
2. 2 Unpacking ..............................................................................................................
3. Operation Setting
3. 1 DIP Switch Setting ..................................................................................................
4. Installation ..............................................................................................................
5. ON-SCREEN DISPLAY PROGRAM MENU
5. 1 Motion Setting.........................................................................................................
5. 2 Dome Setting .........................................................................................................
5. 3 Camera Setting.......................................................................................................
5. 4 Clear Setting ..........................................................................................................
5. 5 PTZ Reset ..............................................................................................................
6. SPECIFICATION
6. 1 Mechanism Specification .......................................................................................
6. 2 Camera Specification..............................................................................................
7. DIMENSION
7. 1 Camera ..................................................................................................................

04
Explosion proof PTZ Camera User’s Guide
05
Explosion proof PTZ Camera User’s Guide
2. 1 Discriptions
1/4" Sony Super HAD II (Double Scan )CCD, Optical 36x with WDR
2. 2 Unpacking
2. Discriptions
3. 1 DIP switch setting
3. Operation Setting
Set the protocol, address and dipswitch before set the camera.
0
9
8
7
654
3
2
10 9
8
7
654
3
2
10 9
8
7
654
3
2
1ON DIP
12345678
Open the top cover of the camera to find the setting switch.
0
9
8
7
654
3
2
10 9
8
7
654
3
2
10 9
8
7
654
3
2
1
SW201 SW202 SW203 ex) SW201 = 1
SW202 = 2
SW203 = 8
ID No:128
ON DIP
12345678
2. Protocol, Baudrate, Camera setting
1.Camera ID (Address)
* Max.ID setting: 1~255
Address switch setting switch
S3 : 1-digit number of address
S2 : 10-digit number of address
S1 : 100-digit number of address
1~2 : Protocol setup
3~4 : Communication speed setup
6 : NTSC, PAL setup
7 : Communication setup
5 : TOP / BOTTOM setup
8 : DEBUG
Camera body
Sunshield Sunshield Bolt Manual
Installation
Bracket (option) Bracket Bolt
(option) Tool
1
OFF
OFF
ON
2
OFF
ON
OFF
PROTOCOL
PELCO D
PELCO P
WONWOO
6
OFF
ON
NTSC/PAL
NTSC
PAL
7
OFF
ON
RS
RS422
RS485
5
OFF
ON
TOP/BOTTOM
TOP
BOTTOM
8
OFF
ON
DEBUG
OFF
ON
3
OFF
OFF
ON
ON
4
OFF
ON
OFF
ON
BAUDRATE
2400
4800
9600
57600

06
Explosion proof PTZ Camera User’s Guide
07
Explosion proof PTZ Camera User’s Guide
5. 1 Motion Setting
The initialize screen is shown up to check address, version,
protocol and video when the power on.
MAIN MENU
< NEAR / RIGHT →PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
The preset function is that the camera memorizes
positions of the pan/tilt and zoom. This function is
a representative function of the PTZ camera which
can find memorized preset positions just by selecting
the preset No. A Maximum of 255 Preset positions
are toured in
order.
5. 1. 1 Preset
PRESET MENU
< NEAR / RIGHT →PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET SELECT 1
(1) Select the Preset number
P01 : Defined Preset number / 01 : Undefined Preset number
Move : Select : NEAR
MOTION MENU
< NEAR / RIGHT →PRESET >
PRESET
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
ઔ
NEAR /MOVE & JOYSTICK>
4. Installation 5. ON-SCREEN DISPLAY PROGRAM MENU
* Caution: Do not turn the tilt angle to 360.
Set the camera using the
installation bracket as the left picture.
Preset Quick Operating Guide
Set Preset : 1~255 +
Go to Preset : 1~255 +
PRESET
PRESET
3sec.
INITIALIZE
ADDRESS
FIRMWARE
VIDEO
PROTOCOL
BAUDRATE
: 001
: X .XX
: NTSC EMC
: PELCO D
: 2400, N, 1
C : X .XX
EM363SN
PAN POS . . . . . . . . PASS
TILT POS . . . . . . . . PASS
CAMERA . . . . . . . . PASS
NORMAL SETTING

08
Explosion proof PTZ Camera User’s Guide
09
Explosion proof PTZ Camera User’s Guide
PRESET MENU
< NEAR / RIGHT
ઔ
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT
ઔ
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX .X , XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT
ઔ
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
(4) Select the focus mode for Preset
PRESET POSITION
(3) Define the Preset position
① Select the Position menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
PRESET LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : PRESET 01
(2) Set the Preset Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Preset.
After the label is set, push the NEAR button to exit.
On focus menu, there are 4 modes : Auto, Manual,
On Shot. It allows detailed settings for the preset.
① Select the Focus menu
or
NEAR
② Move and set the Focus Menu
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
POSITION : 000. 0 , 000. 0
<EXIT FOCUS NEAR >
PRESET MENU
< NEAR / RIGHT
ઔ
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
EXTEND SET ▶
(5) “Save” above setting Pattern data to the memory.
(6) “CLR” means above setting Pattern data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU.

10
Explosion proof PTZ Camera User’s Guide
11
Explosion proof PTZ Camera User’s Guide
MAIN MENU
< NEAR / RIGHT →PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
TOUR >
PRESET
ઔ
TOUR ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
TOUR MENU
< NEAR / RIGHT
ઔ
TOUR NO >
TOUR NO : 01 UNDEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
TOUR SELECT
< SEL →NEAR / MOVE
ઔ
JOYSTICK >
01 02 03 04 05 06
07 08
(1) Select the Tour number
T01 : Defined Tour number / 01 : Undefined Tour number
Move : Select : NEAR
The Tour function consists of several presets run by turn. It is also adjusts the moving speed
(1~63 step) and dwell time (1~99secs). Maximum of 8 Tour functions are toured in order.
5. 1. 2 Tour
( 1 Tour can be set for 15 presets. )
※
TOUR MENU
< NEAR / RIGHT →TOUR NO >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(3) Define the Preset position
① Move to the set-up window
or
NEAR
② Move and set the position ③ Set & Back
NEAR
TOUR EDIT (01)
NO PRESET SPEED DWELL
01 ◀01 63 01
02 ◁ 02 63 01
03 ◁ XX XX XX
04 ◁ XX XX XX
05 ◁ XX XX XX
06 ◁ XX XX XX
07 ◁ XX XX XX
08 ◁ XX XX XX
< SEL & NEAR PRESET & LEFT >
(2) Set the Tour Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Tour.
After the label is set, push the NEAR button to exit.
PRESET SELECT 1
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
ઔ
NEAR /MOVE & JOYSTICK>
TOUR LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : TOUR 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
TOUR MENU
< NEAR / RIGHT
ઔ
TOUR NO >
TOUR NO : 01 DEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
TOUR MENU
< NEAR / RIGHT →DATA SAVE >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(4) “Save” above setting Pattern data to the memory.
(5) “CLR” means above setting Pattern data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU.
Tour Quick Operating Guide
Set Tour : 71~78 + 3sec.
Go to Tour : 71~78 +
PRESET
Set Tour : 1~8 + 3sec.
TOUR
PRESET
Go to Tour : 1~8 + TOUR

12
Explosion proof PTZ Camera User’s Guide
13
Explosion proof PTZ Camera User’s Guide
SCAN SELECT
< SEL
ઔ
NEAR / MOVE

JOYSTICK >
01 02 03 04 05 06
07 08
SCAN MENU
< NEAR / RIGHT
ઔ
SCAN NO >
SCAN NO : 01 UNDEFINE
LABEL :
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
SCAN NO >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
START POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
END POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
(1) Select the Scan number
S01 : Defined Scan number / 01 : Undefined Scan number
Move : Select : NEAR
The Scan function means that the camera keeps panning between two programmed pan positions.
It is also adjusts the moving speed(1~63 step). Maximum 8 Scan functions are toured in order.
5. 1. 3 Scan
STRAT POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0, 000.0
(3) Define the Start pan position
① Select Start Pos menu
or
NEAR
② Move and set the position ③ Go back
NEAR
(2) Set the Scan Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
(4) Define the End pan position
① Select End Pos menu
or
NEAR
② Move and set the position ③ Go back
NEAR
POSITION : 000.0, 000.0
END POSITION
< EXIT →FOCUS NEAR >
It’s available to set the desired label, displayed on the executing screen of Scan.
After the label is set, push NEAR button to go out.
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
TOUR >
PRESET
ઔ
TOUR
ઔ
SCAN ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
SCAN LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : SCAN 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
Scan Quick Operating Guide
Set Scan : 81~88 +
Go to Scan : 81~88 +
PRESET
Set Scan : 1~8 + Scan
PRESET
Go to Scan : 1~8 + Scan
3sec.
3sec.

14
Explosion proof PTZ Camera User’s Guide
15
Explosion proof PTZ Camera User’s Guide
PATTERN MENU
< NEAR / RIGHT
ઔ
PATTERN NO >
PATTERN NO : 01 UNDEFINE
LABEL :
RECORD :
PLAY :
SAVE CLR BACK EXIT
PATTERN SELECT
< SEL
ઔ
NEAR / MOVE & JOYSTICK >
01 02 03 04
(1) Select the Pattern number
PAT01 : Defined Pattern number / 01 : Undefined Pattern number
Move : Select : NEAR
The Pattern function memorizes User’s random moving path and zoom ratio. Total recording time
limit is 90secs and maximum 4 Pattern functions are toured in order.
5. 1. 4 Pattern
(8) Save above Scan data setting to the memory.
(9) “CLR” means above setting Scan data will not be
saved and be cleared.
(10) “BACK” means it goes back to the previous
menu :Motion.
(11) “EXIT” means it goes out to MENU
(7) Set the Focus
(5) Set the Scan speed
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
SCAN MENU
< NEAR / RIGHT
ઔ
MOVE SPEED >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
PATTERN >
PRESET
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
It adjusts the moving speed from 1~63 steps.
Focus can be set Auto or Manual.
(6) Set the Dwell Time
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
Dwell time means the time that the camera stay at
the start & end pan positions.
It’s adjustable from 1~60 seconds.
Set Pattern : 91~94 +
Go to Pattern : 91~94 +
PRESET
Set Pattern : 1~4 + Pattern
PRESET
Go to Pattern : 1~4 + Pattern
Pattern Quick Operating Guide
3sec.
3sec.

16
Explosion proof PTZ Camera User’s Guide
17
Explosion proof PTZ Camera User’s Guide
PATTERN MENU
< NEAR / RIGHT
ઔ
EDIT LABEL >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
ઔ
PLAY
ઔ
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
ઔ
RECORD >
PATTERN NO : 01 DEFINE
LABEL :
RECORD ▶
PLAY
ઔ
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
ઔ
PLAY >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
ઔ
<08SEC>
PLAY
ઔ
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
ઔ
PLAY >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
ઔ
<08SEC>
PLAY
ઔ
SAVE CLR BACK EXIT
(4) Play back the recorded Pattern data
(3) Record and Save the User’s random Pattern data
① Select the “Record” Menu
or
NEAR
② Move and record the pattern ③ Set & Back
NEAR
000.0, 000.0
EXIT
ઔ
NEAR 06/60
PATTERN RECORD
(2) Set the Pattern Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Pattern.
After the label set, push NEAR button to go out.
(5) “Save” above setting Pattern data to the memory.
(6) “CLR” means above setting Pattern data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU.
PATTERN LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : PATTERN
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >

18
Explosion proof PTZ Camera User’s Guide
19
Explosion proof PTZ Camera User’s Guide
AREA MENU
< NEAR / RIGHT
ઔ
AREA NO > <SEL & MEAR / MOVE & JOYSTICK>
AREA NO : 01 UNDEFINE
LABEL :
START PAN POS.: XXX . X
STOP PAN POS.: XXX . X
SAVE CLR BACK EXIT
AREA MENU
< MOVE & NEAR / JOYSTICK >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: 000 . 0
STOP PAN POS.: 000 . 0
SAVE CLR BACK EXIT
AREA MENU
< MOVE & NEAR / JOYSTICK >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: 000 . 0
STOP PAN POS.: 000 . 0
SAVE CLR BACK EXIT
AREA MENU
< NEAR / RIGHT
ઔ
AREA NO >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: XXX . X
STOP PAN POS.: XXX . X
SAVE CLR BACK EXIT
AREA MENU
< NEAR / RIGHT
ઔ
AREA >
AREA NO : 01 DEFINE
LABEL : AREA 01
START POS : 000 . 0 .
STOP POS : 000 . 0 .
SAVE CLR BACK EXIT
The Area function means that it displays the Area name between two programmed pan positions.
Maximun 16 Area functions are toured in order.
5. 1. 5 Area
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
PATTERN >
PRESET
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA ઔ
PRIVACY
ઔ
BACK EXIT
AREA SELECT
01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16
(1) Select the Area number
AR 01 : Defined Area number / 01 : Undefined Area number
Move : Select : NEAR
(2) Set the Area Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Area.
After the label set, push NEAR button to go out.
AREA START PAN POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0
AREA STOP PAN POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0
(3) Define the Start pan position
① Select the “Start Pan Pos” menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
(4) Define the Stop pan position
① Select the “Start Pan Pos” Menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
** Only pan position is adjustable, becaue tilt position is fixed when “Start Pan Position” is set.
(5) “Save” above setting Area data to the memory.
(6) “CLR” means above setting Area data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU
AREA LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : AREA
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
※ Camera will move to clockwise direction only when START setting.

20
Explosion proof PTZ Camera User’s Guide
21
Explosion proof PTZ Camera User’s Guide
ALARM MENU
< NEAR / RIGHT

ALARM NO >
ALARM NO : 01 UNDEFINE
LABEL :
PRESET NO. : XX
SAVE CLR BACK EXIT
ALARM MENU
< NEAR / RIGHT

ALARM LABEL >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : XX
SAVE CLR BACK EXIT
ALARM MENU
< NEAR / RIGHT

SELECT PRESET >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : 01
SAVE CLR BACK EXIT
The Alarm function means that the camera moves to the programmed Preset position by the Alarm trigger.
Maximum 2 Alarm functions are toured in order.
5. 1. 6 Alarm
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
PATTERN >
PRESET
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
(1) Select the Alarm number
Alarm 01 : Defined Alarm number / 01 : Undefined Alarm number
Move : Select : NEAR
(2) Set the Alarm Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Alarm.
After the label is set, push the NEAR button to exit.
(3) Define the Preset position with Alarm trigger
① Select the “Preset No”
or
NEAR
② Move and set the position ③ Set & Back
NEAR
(4) “Save” above setting Alarm data to the memory.
(5) “CLR” means above setting Alarm data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU
PRESET SELECT
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
ઔ
NEAR /MOVE & JOYSTICK>
ALARM LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : ALARM 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
ALARM MENU
< NEAR / RIGHT

SELECT PRESET >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : 01
SAVE CLR BACK EXIT
ALARM SELECT
< SEL →NEAR / MOVE  JOYSTICK >
01 02

22
Explosion proof PTZ Camera User’s Guide
23
Explosion proof PTZ Camera User’s Guide
PRIVACY MENU
< NEAR / RIGHT
ઔ
AREA >
SAVE CLR BACK EXIT
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
PATTERN >
PRESET
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY ઔ
BACK EXIT
The Privacy Zone Masking function means that it sets the blocking territories to prevent camera functions
for the privacy of personal reasons. Maximum of 8 Privacy Zone Masking functions are toured in order.
5. 1. 7 Privacy Zone Masking
PRIVACY MENU
< NEAR / RIGHT
ઔ
PRIVACY NO >
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
SAVE CLR BACK EXIT
PRIVACY MENU
< NEAR / RIGHT
ઔ
PRIVACY NO >
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
SAVE CLR BACK EXIT
PRIVACY SELECT
< SEL →NEAR / MOVE
ઔ
JOYSTICK >
01 02 03 04 05
06 07 08
(1) Select the Privacy Zone number
Privacy 01 : Defined Alarm number / 01 : Undefined Alarm number
Move : Select : NEAR
(2) Set the Privacy Zone Position
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired position and size of the blocking territories freely.
After the Privacy Zone is set, push the NEAR button to go out.
PRIVACY POSITION
< EXIT
ઔ
FOCUS NEAR >
POSITION : 000. 0 , 000 .
MASK SIZE : <OPEN / CLOSE >
(3) “Save” above settings of Privacy Zone data to the memory.
(4) “CLR” means above setting of Privacy Zone data will not
be saved and be cleared.
(5) “BACK” means it goes back to the previous
menu :Motion.
(6) “EXIT” means it goes out of MENU.

24
Explosion proof PTZ Camera User’s Guide
25
Explosion proof PTZ Camera User’s Guide
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
(1) Set the park Time (OFF, 01~60 min)
5. 2. 4 PARK ACTION
or NEAR
This function enables to locate the camera to specific
position automatically if operator doesn’t operate the
controller for a while.
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
NEAR
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
ઔ
BACK EXIT
5. 2 Dome Setting
5. 2. 2 Set the Power Up Action
When this function is ON, the camera memorizes the latest action and restores, it from sudden power
failure.
Select : or Set ON : Set OFF :
NEAR
5. 2. 1 Set the Dome camera title
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired camera title.
After the label is set, push NEAR button to exit.
Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” Menu.
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE SET
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL :
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
5. 2. 3 MOTOR SPEED SETTING
Set motor speed from 01~05 and bigger number is faster speed.
** 03 ( <- Default)
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
NEAR
Select : or Set ON : Set OFF :
NEAR

26 27
Explosion proof PTZ Camera User’s Guide
Explosion proof PTZ Camera User’s Guide
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
(2) Select the function which will be back
after the above set time.
(3) Select the appointed function’s Number
< NEAR / RIGHT
ઔ
DWELL >
SAVE CLR BACK EXIT
(4) “Save” above setting data to the memory.
(5) “CLR” means above setting Pattern data will
not be saved and be cleared.
(6) “BACK” means it goes back to the previous
menu.
(7) “EXIT” means it goes out of the MENU
PARK MENU
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
5. 2. 5 Display ON/OFF Set
You can select the OSD ON to shown on the screen or clear by selecting OFF in this function.
Select : or Set ON : Set OFF :
NEAR NEAR
Select : or Set ON : Set OFF :
NEAR NEAR
DISPLAY ON/OFF MENU
TITLE :
ZOOM :
PRESET :
TOUR :
AREA :
ALARM :
PATTERN :
PRIVACY :
SCAN :
POSITION :
ACTION :
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<ON
ઔ
TETLE MOVE
ઔ
JOY >
<OFF
ઔ
WIDE BACK
ઔ
NEAR>
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
TITLE SET >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
2) Auto Flip ON/OFF SETTING
The tilt angle is extended to 90º
when this function is ON.
DOME MENU
BACK
< NEAR / RIGHT
ઔ
FUNCTION >
5. 2. 6 DOME SUB MENU SETTING

1) Speed By Zoom ON/OFF
Pan and Tilt speed can be changed depending on zoom magnification.
ON will slow down the speed of Pan/Tilt and OFF will increase the Pan/Tilt speed.
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
SPEED BY ZOOM
AUTO FLIP
RESPONSE TXD
PRESET FREEZE
: ON
: OFF
: OFF
: OFF
DOME MENU
BACK
< NEAR / RIGHT
ઔ
FUNCTION >
SPEED BY ZOOM
AUTO FLIP
RESPONSE TXD
PRESET FREEZE
: ON
: ON
: OFF
: OFF
3) RESPONSE TXD SETTING
Send the response from PTZ throught the TXD line.
(Support Pelco-D protocol only)
DOME MENU
BACK
< NEAR / RIGHT
ઔ
FUNCTION >
SPEED BY ZOOM
AUTO FLIP
RESPONSE TXD
PRESET FREEZE
: ON
: ON
: OFF
: OFF
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR

28
Explosion proof PTZ Camera User’s Guide
29
Explosion proof PTZ Camera User’s Guide
5. 3 Camera Setting
4) PRESET FREEZE
Display start image and finished image only.
Static image on-screen during the camera movement.
DOME MENU
BACK
< NEAR / RIGHT
ઔ
FUNCTION >
SPEED BY ZOOM
AUTO FLIP
RESPONSE TXD
PRESET FREEZE
: ON
: ON
: OFF
: OFF
5. 2. 8 Factory Set
Restore all of setting value to the factory default.
All of existing setting value
will be erased
5. 2. 7 TEMPERATURE SET
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
TEMP MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
HEATER ON TEMP : 5C
HEATER ON TIME : 30MIN
HEATER OFF TEMP : 30C
FAN ON TEMP :50C
FAN OFF TEMP :40C
CURRENT TEMPER :25.31C
DOME MENU
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FUNCTION >
TITLE
POWER UP ACTION: ON
MOTOR SPEED: 03
PARK ACTION ▶
DISPLAY ON/OFF ▶
DOME SUB MENU ▶
TEMP.SET
FACTORY SET
1) HEATER ON TEMP: 5°C(Default) : Set the operating temperature of the heater.
2) HEATER ON TIME: 30MIN (Default) : Set the operating time of the heater.
3) HEATER OFF TEMP: 30°C(Default) : Set the temerature of heater OFF
4) FAN ON TEMP:50°C(Default) : Set the operating temperature of the Fan
5) FAN OFF TEMP: 40°C(Default): Set the temperature of Fan OFF.
6) CURRENT TEMPER :Show the PTZ current temperature.
▶
Select : or Set ON :
Set OFF :
NEAR
NEAR
D-ZOOM (Digital Zoom)
- Magnification of the Digital Zoom can be switched On and Off.
- It is recommended that the Digital Zoom should be set up before the preset operation.
- As the digital zoom magnification increases, the image quality is lowered.
=22002'(
)2&8602'(
$(02'(
:%02'(
,&502'(
63(&,$/
&$05(6(7
1($55,*+7ୄ=2206(7!
୅
୅
୅
୅
୅
୅
୅
6$9(%$&.(;,7
&$0(5$0(18
ZOOM MENU
ZOOM SPD : 7
D-ZOOM : OFF
BACK
< NEAR / RIGHT
ઔ
ZOOM SPEED>
ZOOM MENU
ZOOM SPD : 7
D-ZOOM : OFF
BACK
< NEAR / RIGHT
ઔ
D-ZOOM >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
ZOOM SPD : Select from 0 Step to 7 steps
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
5. 3. 1 ZOOM MODE
Zoom speed can be set and decide using of digital
zoom function.
Camera menu subject to change without prior notice to upgrade and quality increase and
we may use slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual
menu is not matched.

30
Explosion proof PTZ Camera User’s Guide
31
Explosion proof PTZ Camera User’s Guide
5. 3. 2 FOCUS
In Focus menu, you can set up the focus mode among Auto, One Push, Manual or Infinity.
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
FOCUS SET >
select : or Set ON :
Set OFF :
NEAR
NEAR
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode.
In the auto focusing mode, zoom key operation is not
recognized as the input of the focus key.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically.
This is for focusing accurately after zooming.
Manual: In the manual mode, users can adjust the camera
focus manually.
Infinity: infinity focus is the state where a lens forms an image
of an object an infinite distance away.
This corresponds to the point of focus for parallel rays.
Set the speed for camera focusing.(0~7)
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 5
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
ઔ
FOCUS MODE >
FOCUS MENU
FOCUS MODE : MANUAL
FOCUS SPD : 5
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
ઔ
FOCUS SPD >
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the focus distance.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD :
XXXX
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
ઔ
NEAR LIMIT >
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
AE SET >
5. 3. 3 AUTO EXPOSURE
AUTO EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
AE MODE >
AE setting is a function adjusting shutter speed, IRIS, AGC
acoording to subject’s brightness to get standard amount of
exposed light.
AF MODE: Set the auto focuse mode
select : or Set ON :
Set OFF :
NEAR
NEAR
SENSITIVITY: Set the sensitivity of focus
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
Select AUTO,MANUAL,SHUTTER or IRIS.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD :
XXXX
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
ઔ
AF MODE >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD :
XXXX
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
ઔ
SENSITIVITY >

32
Explosion proof PTZ Camera User’s Guide
33
Explosion proof PTZ Camera User’s Guide
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
SHUTTER SPD >
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
SLOW SHT >
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
IRIS LEVEL >
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
GAIN LEVEL >
select : or Set ON :
Set OFF :
NEAR
NEAR
Select ON/ OFF.
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set SHUTTER in the AE MODE, you can control image
brightness by adjusting shutter speed.
Set from x512, x128, x64, x32, x16, x8, 1/15, 1/30, 1/60 ,
1/90 , 1/100, 1/180, 1/250, 1/500, 1/1000, 1/1500, 1/2000,
1/5000, 1/10000, 1/20000, 1/50000, 1/100000
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set IRIS in the AE MODE, you can set the IRIS level
from 00 to 17 .
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set MANUAL, IRIS and SHUTTER in the AE MODE, you can
set the GAIN for brighter image from 0~30dB. (Changable by 2dB)
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
AGC MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
EXPO. MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
ઔ
EXPO. LEVEL >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
Select ON/ OFF in AGC MODE.
select : or Set ON :
Set OFF :
NEAR
NEAR
Select AUTO or Manual.
If you set ON in the EXPO MODE, you can control this level.
( "0" is standard (±10.5 selectable), changed bt 1.5dB)

34
Explosion proof PTZ Camera User’s Guide
35
Explosion proof PTZ Camera User’s Guide
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
WB SET >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
5. 3. 4 WHITE BALANCE
Set the white balance of camera.
WHITE BALANCE MENU
WB MODE : ATW
RED GAIN : xxx
BLUE GAIN: xxx
BACK
< NEAR / RIGHT
ઔ
WB MODE SEL >
WHITE BALANCE MENU
WB MODE : MANUAL
RED GAIN : 208
BLUE GAIN: 162
BACK
< NEAR / RIGHT
ઔ
R GAIN SEL >
White balance setting is a function revising color temperature
to resolve the problem that screen’s colors change by the color
temperature’s difference according to time.
WB MODE: Set the color depend on white balacne.
Select AUTO, INDOOR, OUTDOOR, ONEPUSHWB,
ATW or MANUAL.
RED GAIN: Adjust red color level from 0~255.
(Standard level is 025)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 025)
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAMERA RESET
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
ઔ
SAVE BACK EXIT
< NEAR / RIGHT
ઔ
ICR SET >
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :11
BACK
< NEAR / RIGHT
ઔ
ICR MODE >
5. 3. 5 ICR MODE
Select AUTO, DAY ,NIGHT, EXT, SENSEIN.
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :11
BACK
< NEAR / RIGHT
ઔ
ICR THRESHOLD >
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the ICR THRESHOLD from 00 to 28 .

36
Explosion proof PTZ Camera User’s Guide
37
Explosion proof PTZ Camera User’s Guide
MAIN MENU
< NEAR / RIGHT
ઔ
SPECIAL SET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
CAM RESET
ઔ
SPECIAL ઔ
SAVE BACK EXIT
5. 3. 6 SPECIAL
In the Special menu, it’s available to set SUB SP MODE,
SHARPNESSGAIN, FLICKERLESS, BACK LIGHT, LINE LOCK
V-PHASE, DNR LEVEL and WDR.
SUB SP MODE : In the Special menu, it’s available
to set special function of the camera
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
ON/OFF>
STABILIZER : OFF
HR MODE : OFF
HLC MODE : OFF
HLC CLIP LEVEL : XX
HLC LEVEL : XX
STABILIZER: Select ON or OFF.
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
ON/OFF>
STABILIZER : OFF
HR MODE : OFF
HLC MODE : ON
HLC CLIP LEVEL : XX
HLC LEVEL : XX
HR MODE : Select ON or OFF.
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
SUB MENU >
SUB SP MODE ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
ON/OFF>
STABILIZER : OFF
HR MODE : OFF
HLC MODE : ON
HLC CLIP LEVEL : XX
HLC LEVEL : XX
HLC MODE : Select ON or OFF.
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
LEVEL>
STABILIZER : OFF
HR MODE : OFF
HLC MODE : ON
HLC CLIP LEVEL : 03
HLC LEVEL : XX
HLC CLIP LEVEL : Select HLC function ON and set the HLC
CLIP LEVEL.
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
LEVEL>
STABILIZER : OFF
HR MODE : OFF
HLC MODE : ON
HLC CLIP LEVEL : 03
HLC LEVEL : 02
HLC LEVEL : Set the HLC LEVEL.
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR

38
Explosion proof PTZ Camera User’s Guide
39
Explosion proof PTZ Camera User’s Guide
Set the SHARPNESSGAIN value.
Select ON/OFF in the FLICKERLESS function.
Select ON/OFF in the BACK LIGHT function.
Select ON/OFF in the LINE LOCK function.
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
SHARPNESSGAIN >
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
FLICKERLESS >
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
BACK LIGHT >
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
SPECIAL MENU
BACK
< NEAR / RIGHT
ઔ
LINE LOCK >
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
MAIN MENU
< NEAR / RIGHT
ઔ
RESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
CAM RESET ઔ
SPECIAL
ઔ
SAVE BACK EXIT
Make initialize the setting value which is set in CAMERA MENU.
5. 3. 7 CAMERA RESET
Move : Select : NEAR
If you set ON in the LINE LOCK menu, you can set
the V PHASE.
Set the DNR LEVEL from AUTO, OFF and 1 ~ 10.
Set the WDR MODE from OFF, LEV1 ~LEV7.
SPECIAL MENU
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
ઔ
V PHASE >
SPECIAL MENU
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
ઔ
DNR LEVEL >
SPECIAL MENU
SUB SP MODE
ઔ
SHARPNESSGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
ઔ
WDR MODE >
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR