Cam Scan CS-SD227DN User manual

Enhanced Speed Dome Camera
CS-SD227DN, CS-SD276DN
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
P/N : 388064138
PRINTED IN KOREA
Wall In-Ceiling Ceiling
INSTALLATION / OPERATING MANUAL

02 03
1. 1 Important Safety Instructions
• Read these instructions carefully.
• Pay attention to all the warnings.
• Follow all instructions.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not disassemble or insert foreign objects.
• Do not install near any heat sources such as radiation, stoves, or other apparatus
Including amplifiers that produce any heat.
• Do not aim the camera at the sun or any other strong light source.
• Do not install the camera on intermittent lighting environments.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tipping.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Installation should be done only by qualified personnel and conform to all local codes.
• Installation should be done in a place strong enough to hold it.
• Use only installation methods and materials capable of supporting four times the maximum specified load.
• It is designed for indoor use only and it must not be installed where exposed to rain and moisture
without additional outdoor housing and bracket.
• To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
• These instructions are for use by qualified service personnel only. To reduce the risk of electrical shock
do not perform any servicing or repair other that contained in the operating instructions unless you are
qualified to do so.
• Only use replacement parts recommended by manufacturer in these instructions.
1. PRECAUTIONS
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
8p.
10p.
12p.
12p.
13p.
14p.
14p.
16p.
18p.
19p.
19p.
21p.
22p.
31p.
31p.
32p.
33p.
35p.
35p.
36p.
36p.
37p.
38p.
1. PRECAUTIONS
1. 1 Important Safety Instructions...................................................................................
2. GETTING STARTED
2. 1 Descriptions ..........................................................................................................
2. 2 Unpacking ..............................................................................................................
2. 3 Model Selection Flow ..............................................................................................
2. 4 Features .................................................................................................................
2. 5 Accessories Selection (Sold Separately) ................................................................
2. 6 DIP Switch Setting .................................................................................................
2. 7 Cable Connection ...................................................................................................
3. INSTALLATION
3. 1 Surface Mount .......................................................................................................
3. 2 Inceiling Mount ......................................................................................................
3. 3 Indoor / Outdoor Housing..........................................................................................
4. ON-SCREEN DISPLAY PROGRAM MENU
4. 1 Powering ON ..........................................................................................................
4. 2 Establishing Camera Control ...................................................................................
4. 3 Motion Menu ..........................................................................................................
4. 4 Dome Menu ...........................................................................................................
4. 5 Camera Menu ........................................................................................................
4. 5. 1 CS-SD276DN Camera Setting (1)........................................................................
4. 5. 2 CS-SD276DN Camera Setting (2)......................................................................
4. 5. 3 CS-SD227DN Camera Setting ..........................................................................
4. 6 Clear Menu.............................................................................................................
4. 7 PTZ RESET.............................................................................................................
5. SPECIFICATION
5. 1 Mechanism Specification .......................................................................................
5. 2 Camera Specification..............................................................................................
6. DIMENSION
6. 1 Camera Dimensions .............................................................................................
6. 2 Wall and Ceiling Pipe Plate .....................................................................................
6. 3 Parapet Mount Bracket ...........................................................................................
6. 4 Corner Mount and Pole Mount Bracket ...................................................................
7. CONFIGURATION
7. 1 Connecting to CS-KY2403 with DVR -1...................................................................
7. 2 Connecting to CS-KY2403 with DVR -2 ..................................................................
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

04 05
2. 1 Descriptions 2. 3 Model Selection Flow
2. 2 Unpacking
The following parts are included with outdoor speed PTZ dome system.
1. PTZ
2. Dome cover
3. Plate Base
4. Interface cable with two wired wiper on one end and BNC female on the other end(In-ceiling only)
5. User’s Guide
6. Self-tapping screws & plastic anchors
2. GETTING STARTED
<Figure 1. package Components>
PTZ
Plate Base
Plastic Anchors Screws(3x8)Screws(4x25)
Video Cable User’s Guide
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
2. 3. 1 Indoor 2. 3. 2 Outdoor
Mount Type
Indoor Surface Mount
In-ceiling Mount
Indoor Ceiling Mount
Optional bracket Mount Type Optional bracket
B type Base
B type Base
B type Base
B type Base
Inceiling Bracket
Indoor Wall Mount
300mm Ceiling Bracket
500mm Ceiling Bracket
Wall Bracket
Outdoor Wall Mount Outdoor Housing + Wall Pipe Plate
+Installation Box
Outdoor Housing + Ceiling Bracket
(300mm or 500mm)
Outdoor ceiling Mount
Outdoor Corner & Pole Mount
Outdoor Parapet Mount
Outdoor Housing + Wall Pipe Plate
+ Corner or Pole Mount Bracket
Outdoor Housing+
Parapet Mount
Bracket
This Speed Dome Series are the latest surveillance camera using state of the art technology. It features
various functions including optical auto focus zoom, heavy duty high-speed pan/tilt mechanism and
mechanical IR removal cut-filter. Additional functions include auto focus tracking and preset accuracy of
less than 0.1°, 255 preset positions, 8 privacy masking zones, 4 record 240sec patterns, Auto Flip, and its
ability to automatically detect multiple protocols.This compact speed dome will withstand all types of
weather conditions with its IP66 outdoor housing with heater and blower. This Speed Dome Series deliver a
variety of advanced features and functions making it the perfect choice for security professionals.

06 07
2. 5 Accessories Selection (Sold Separately)2. 4 Features
2. 4. 1 High Speed PTZ dome camera
(CS-SD227DN)
- 610K pixel 1/4” SONY Super HAD Dual Scan CCD
- 700TV lines of most high resolution
- Optical 22x power zoom and 32x digital zoom
- Day & Night (ICR)
- Dual scan 512x WDR
- Digital Noise Reduction(2D+3D)
- Intelligent Motion / Object Detection
- 255 Presets / 8 programmable Tour / 4 Pattern
- Digital Auto Flip
(CS-SD276DN)
1/4" Sony Super HAD CCD
Optical 27x zoom and 12x digital zoom
Day & Night (ICR)
Digital Noise Reduction
255 Presets / 8 programmable Tour / 4 Pattern
Digital Auto Flip
2. 5. 1 Out/Indoor environmental Applications
Item
Wall Bracket
Image
Description
- Aluminum body
- Unit: 1.0Kg
- Cool gray / Black
Wall Pipe Plate Ceiling Pipe Plate
(300mm)
(500mm)
(300mm)
(500mm)
Ceiling Plate Pipe Adaptor
- Unit: 3.1Kg
- Cool gray color
- Aluminum & Steel body
- Steel body
- Unit : 1.4Kg
- Cool gray color
- Aluminum diecasting
- Unit : 5.0Kg
- Silver color
- Aluminum & Steel body
- Unit : 1.6Kg,
- Cool gray color
Item
In-ceiling Mount Housing
Image
Description
Item
Parapet Mount Bracket
Image
Description
- Stainless steel(SUS) body
- Unit : 5.2Kg
- Maximum load : 20Kg
- Dimensions : 890x650 (Arm)
- 250x350 (Mount plate)
Mounting Adaptor Mounting Adaptor Installation Box
- Steel body
- Unit: 1.3Kg
- Cool gray color
- Steel body
- Unit: 0.7Kg
- Cool gray color
- Steel body
- Unit: 0.4Kg
- Cool gray color
Outdoor Housing with flange Mounting Flange Sun Visor
- Aluminum body
- Unit: 3.1Kg
- Cool gray color
- For wall/ceiling mount
- Aluminum body
- Cool gray color
- Aluminum body
- Unit: 0.6Kg
- Cool gray color
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

08 09
2. 6. 2 Set the termination On/Off
2. 6 DIP Switch Setting
2. 6. 1 Dip Switch Setting
Before using the dome camera set the dip-switches and clock-switches to the correct protocol,
camera address, and termination settings
The device which is connected at the end of the line must have the cable communication terminated.
Without proper termination, there is potential for control signal errors.
The Camera can have the cable communication terminated by setting the appropriate dip switch as shown
below.
1: On 2: On ' Terminated
1: Off 2: Off ' Not terminated
2. 6. 3 Set the camera address (ID)
2. 6. 4 Set the details of the dome
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
① Separate the dome with the bottom plate.
(Turn the camera counterclockwise from the bottom plate.)
< Bottom side connector board >
8
2
8
7
6
5
7
3
4 6
5
S2
9
0
1
9
0
2
3
41
S3
S3: 1-digit number of address (ID)
S2: 10-digit number of address (ID)
S1: 100-digit number of address (ID)
Ex) If S1=1, S2=2, S3=8, then the ID number is 128.
To prevent electrical damage, each dome camera must have a unique address (ID).
Set the details of the dome
S4(1~3) : Protocol
S4(4)S5(1,2) : Band Rate
S5(3,4) : Parity
S6(1,2) : Camera Module
S6(3) : Video Format
S6(4) : Communication
N.COn
EM
On FCB
Off
SDMOff
2
On
Off
On
Off
1Camera Module
S6
412
Off Off Off
Off Off On
Off On Off
Off On On
On Off Off
On Off On
On On Off
On On On
9600 bps
4800 bps
2400 bps
N.C
57600 bps
38400 bps
19200 bps
S4 / S5 Band Rate
N.C 4
On
Off RS-422
RS-485
S6 Communication
3
On
Off NTSC
PAL
S6 Video Format
* When the camera is ON, camera protocols will be fixed with the first detected protocol.
N.C
S5
34
off off
off on
on off
on on
none
even
odd
Parity
AC~
G
1 2
ON
5
6
7
89012
3
4
S4
43
2
1
0
9
8
765
S3
S5
S6
S1
S2
-- 0 1
-- 1 1
Reserved
Reserved
Cameramodule
S/TX30
AutoDete
- - 0 1
- - 0 0
RS-485
Communication
-1 - -
-0 - -
RS-422
NTSC
PAL
VideoFormat
S4
S4
S4
0- - -
12 3 4
12 3 4
12 3 4
I/O 1
I/O 2
VIDEO
43
2
1
0
9
8
765
GND
TX -
TX +
RX -
RX +
G
ON ON
123
Off Off Off
Off Off On
Off On Off
Off On On
On Off Off
On Off On
On On Off
On On On
CSN
Pelco-D v.1.0
CSD
N.C
N.C
N.C
Pelco-D v.5.0
S4 Protocol
N.C

10 11
2. 7 Cable Connection 2. 7. 3 Alarm connection
Power connection
- Connect the power of AC 24V, 1000mA to this dome camera.
- Use certified / Listed Class 2 power supply transformers only.
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
2. 7. 1 Power/Data communication cable connection
-> One way communication with any Keyboard controller by RS-485/ RS-422.
-> Two way communication with video server or other equimpemnt by RS-422.
Simply connect TX- and TX+ of contoller to RX- and RX+ of camera as above.
Connect RX-,RX+,TX- and TX+ of quipment to TX-, TX+, RX- and RX+ of Camera as shown below.
2. 7. 2 Video Output connection
Connect the video out (BNC) connector to the monitor or video input of DVR.
(Video cable and RS-485/422 communication cables are not provided in this product's package.)
VIDEO OUT
Tx - / Tx +
POWER AC 24V
FGND
Rx -
Rx +
Tx -
Tx +
AC
FGND
AC
N N C G 8 7 6 5
O C O N O C O N
N N C G 4 3 2 1
G Tx- Tx+ Rx- Rx+
AC~G
on
1 2
I/O 1
I/O 2
VIDEO
ALARM INPUT(I/O 2)
ALARM INPUT(I/O 1)
RX-
RX+
TX-
TX+
POWER AC 24V
FGND
Rx -
Rx +
Tx -
Tx +
AC
FGND
AC
N N C G 8 7 6 5
O C O N O C O N
N N C G 4 3 2 1
G Tx- Tx+ Rx- Rx+
AC~G
on
1 2
I/O 1
I/O 2
VIDEO
N N C G 8 7 6 5
O C O N
O C O N
N N C G 4 3 2 1
G Tx- Tx+ Rx- Rx+
AC~G
on
1 2
I/O 1
I/O 2
I/O 1 I/O 2
ALARM PIN DETAILS
1ALARM1 1
2ALARM2 2
3ALARM3 3
4ALARM4 4
5 GND 5
6COM1 6
7 NC 1 7
8 NO 1
ALARM5
ALARM6
ALARM7
ALARM8
GND
COM 2
NC 2
NO 28

12 13
3.Installation
3. 1 Surface Mount
3. 2 In-ceiling Mount
- The following steps of installation and connection work should only be done by qualified service
personnel or system installers and should conform to all local codes.
- Be sure to leave the camera off until installation is completed.
- Do not install the camera near the air outlet of an air conditioner.
- Before installation, set the dome system with Dip switch on the back side of the mechanism part, and
assemble the mechanism and housing according to the below instruction.
3. 3 Indoor / Outdoor Housing
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
① Make a cabling hole (70mm diameter) to the
proper position in the ceiling and attach the
included bottom plate.
② Using the safety wire, attach the camera to the
bottom plate.
③ After the cabling, turn clockwise to connect the
camera to the bottom plate.
④ Ensure the camera is not loose by using the side
safety screws.
① Make a cabling hole to the proper position
in the ceiling.
② Before installation, attach the bottom plate to the
in-ceiling housing.
③ Install the In-ceiling housing and pull out the cables
from the ceiling.
④ After the cabling, turn clockwise to connect the
camera to the bottom plate.
⑤ Attach the deco-ring after connecting the camera
system.
① Make wiring and attach the bottom plate in the
Indoor/outdoor housing.
② Using the safety wire, attach the camera to the
bottom plate.
③ After the cabling, turn clockwise to connect the
camera to the bottom plate.
④ Ensure the camera is not loose by using the side
safety screws.
⑤ Attach the dome cover and fasten up by using
the screws.

14 15
4. 1 Powering On
When turning the this camera power on, there is a ten (10) second delay before the camera starts
its homing phase. During the homing phase the camera pans left and right and tilts up and down. It also
adjusts the lens focus.
4. 2 Establishing Camera Control
The most common way to interface with the camera is using a keyboard and on-screen display (OSD)
menu. This method is the most common and is covered in this manual.
4. 2. 1 Basic Keyboard Operation
The following tables summarize the basic operations for a standard keyboard and the functions available
to control this camera.
Table 1. 1 Typical Keyboard Functions
Table 2. 1 Typical Keyboard Controls for this PTZ dome camera system
4. ON-SCREEN DISPLAY PROGRAM MENU
Typical Keyboard Features Usage
Function Keys
Number Keys
Camera Key
Enter Key
Focus Key (Or Near Key)
Iris Key
Key LEDs
LCD
Joystick
Selects a specific control setting
Inputs a number from 0 to 9.
Selects a camera number
Inputs a selection
Sets the lens focus or make a menu selection in OSD menu.
Sets the lens iris setting or makes a menu selection in OSD menu.
Indicates an active key
Displays the current status
Controls a pan/tilt/zoom operation
Dome Operation How to Control
To Pan Side to Side
To Tilt Up and Down
To Zoom In
To Zoom Out
Move the joystick left or right.
Move the joystick forward and back.
Twist the joystick clockwise.
Twist the joystick counterclockwise.
This camera is programmed through the on-screen display (OSD) menus.
To access the OSD menus, you must open the main Setup Menu.
4. 2. 3 Setup Program OSD Menu From Keyborad.
The main Setup Menu provides access to all programmable this camera settings.
4. 2. 2 Keyboard Commands
- Keyboard control commands are composed of a sequence of two (2) inputs with the following
convention: 1) a Command number key(s) + 2) a Function key.
- Command numbers range from 1 to 255.
- Refer to the keyboard manual for the key naming conventions in detail.
4. 2. 4 Go into the camera setup 0SD Menu
Press key “1” and keep pressing the “MENU” key for approximately 3 seconds, or press key “95” and
press “Preset” key to go into the set-up menu. Setup menus are shown in the diagram below. You can
adapt the camera to your requirements by setting up the respective items in these menus.
4. 2. 5 OSD Menu tree
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT ▷ MOTION >
→
→
→
→
MOTION MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
▷
< NEAR / RIGHT ▷ PRESET >
▷
▷
▷
▷
▷
▷
▷
DOME MENU
TITLE :
POWER UP ACTION
PARK ACTION
DISPLAY ON / OFF
SPEED BY ZOOM
AUTO FLIP
FACTORY SET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ TITLE SET >
: ON
▷
▷
: ON
: ON
CLEAR MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
▷
< NEAR / RIGHT ▷ PRESET >
▷
▷
▷
▷
▷
▷
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
< NEAR / RIGHT ▶ ZOOM SET >
▷
▷
▷
▷
▷
▷
▷
SAVE BACK EXIT
CAMERA MENU

16 17
4. 3 Motion Menu
4. 3. 1 PRESET
- Function : Max. 255 positions can be stored as Preset position. The preset number can be assigned
from 1 to 255, but 95 is reserved for starting OSD menu. Camera characteristics
(i.e. White Balance, Auto Exposure) except for Focus can be set up independently for each
preset. Label can be freely set to each Preset position. All characteristics can be set up
in the OSD menu.
- Preset No. : Max. 255 positions can be stored and each position can be assigned as a defined
Preset No.
- Label : Each Preset can have its own label name.
- Position : It displays the coordinates to position the assigned Preset.
- Focus : It enables setting the camera focus for each Preset position. (Default Auto)
4. 3. 2 TOUR
- Function :
By using the Tour function, you can set the camera to move among a Max. 15 Preset
positions
repeatedly. When Tour function runs, camera moves from the preset assigned
as the 1st
point to the preset assigned as the last point in sequence. The camera will stay
to each
point for the time set to the dwell time in Tour Edit and move to the next point.
- Tour No. :
Max. 8 Tours can be stored and the each tour can have Max. 15 Preset positions with the
defined
Tour No.
- Label : Each Tour can have its own label name.
- Tour Edit : The Preset position, Speed and Dwell time can be assigned to each Tour. The Speed
can be set up from 1°/sec to 63°/sec and the Dwell time can be set up from 1sec to 99secs.
4. 3. 3 SCAN
- Function :
By using Scan function, the camera moves between 2 positions if there is no PTZ command
after passing the assigned Dwell time. When there is no camera movement, the Scan function
runs and the camera moves from the position assigned as the starting point to the position
assigned as the end point in Clockwise direction.
- Scan No. : Max. 8 Scans can be stored.
- Label : Each of scan can have its own label name.
- Start position : Assign the coordinate of the Scan starting position.
- End position : Assign the coordinate of the Scan ending position.
- Speed : It enables the setting of the running speed in each coordinate.(1~63sec)
- Dwell : The Scan function runs after the Dwell time without any camera movement.(~59 min)
- Focus : It enables the setting of the camera Focus. (Default is Auto)
MOTION MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
▷
< NEAR / RIGHT ▷ PRESET >
▷
▷
▷
▷
▷
▷
▷
4. 3. 4 PATTERN
- Function :
Pattern function is that a camera memorizes the path (mostly curve path) by joystick of
controller for the assigned time and revives the path exactly as it memorized.
- Pattern No. : 4 Patterns can be stored in Keyboard menu. But if by chance your Keyboard does not
have
this menu, then the Pattern might not be performed correctly.
- Label: Each Pattern can have its own label name.
- Record :
Movement by joystick and preset movement can be memorized in a pattern. To save the recording,
press NEAR key. It records Max. 60seconds. If by chance your Keyboard is not set to WCY
model, then this Record menu might not be performed.
- Play : To revive the Pattern during the recorded time.
4. 3. 5 AREA
- Function :
By using the Area function, you can make the camera move between 2 pan positions
repeatedly.
When Area functions runs, camera moves from the pan position assigned as the
start pan
position to the position assigned as the stop pan position. In case the position
assigned
as the start point is the same as the position assigned as the end position, the
camera turns on its axis by 360° in Clockwise direction and then it turns on its axis by 360° in
counterclockwise
direction.
- Area No. : Max. of 16 Areas can be stored.
- Label : Each Area can have its own label name.
- Start Pan Position : Assign the coordinate of Area starting position.
- Stop Pan Position : Assign the coordinate of Area stopping position.
4. 3. 6 ALARM
- Function :
Alarm function enables the camera to move to the programmed Preset position when there is
Alarm trigger.
- Alarm No. : Max. 8 Alarms can be stored.
- Label : Each Alarm can have its own label name.
- Preset No. : Assign the Preset No. to run when alarm is triggered.
4. 3. 7 PRIVACY
- Function : To protect privacy, Max. of 8 Privacy settings can be created on the arbitrary position to
hide objects
such as windows, shops or private houses With spherical coordinates
system powerful
Privacy zone masking function is possible.
- Privacy No. : 8 Privacy zone can be stored.
- Position : Assign the coordinate to hide with Privacy.
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

18 19
4. 4. 1 TITLE
- Function : Set the camera title to display on screen
- To store the Title, press TELE button on the Keyboard. To delete, press WIDE.
4. 4. 2 POWER UP ACTION
- Function :
This function enables to resume the last action executed before power down. Most of actions
such as Preset, Tour, Pattern, and Scan are available for this function but Jog actions are not
available to resume.
- To activate this function, set this function to ON.
4. 4. 3 PARK ACTION
- Function :
This function enables to locate the camera to specific position automatically if operator doesn’t
operate the controller for a while.
- Time<Min> : The Park time can be assigned from 5min to 60min.
- Function : Can select one of the motion functions, Preset, Tour, Pattern and Scan.
- Number : The number of selected motion function.
4. 4. 4 DISPLAY ON/OFF
- Function : It enables to turn on or off for the menu On-screen display.
-
TITLE, ALARM, ZOOM, POSITION, PRESET, ACTION, TOUR, SCAN, PATTERN, PRIVACY, and AREA menu
On-screen display On/Off
- To turn on the display, press TELE button from the Keyboard. To turn off, press WIDE.
4. 4. 5 SPEED BY ZOOM
- Function :
Pan and Tilt speed can be changed depending on zoom magnification. Tele will slow down
the speed of Pan/Tilt and Wide will increase the Pan/Tilt speed. It will take about 3.5min
for 1 cycle in Tele mode and about 1.5seconds in the Wide mode.
- Default is On.
4. 4. 6 AUTO FLIP
- Function :
In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera keep moving
to opposite tilt direction (180°) to keep tracing targets. As soon as zoom module camera
passes through the top of tilt direction (90°), images should be reversed automatically and
appears in screen. If this function is set to OFF, tilt movement range is 0~90°
-
You can observe the moving object without reversing of the screen, by using this AUTO FLIP function.
4. 4. 7 FACTORY SET
- Function : It makes to restore all of setting value to the factory default.
- Please be careful that all of existing value would be erased by this Factory Set ON.
4. 4 Dome Menu
DOME MENU
TITLE :
POWER UP ACTION
PARK ACTION
DISPLAY ON / OFF
SPEED BY ZOOM
AUTO FLIP
FACTORY SET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ TITLE >
: ON
▷
▷
: ON
: ON
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
4. 5 Camera Menu
① FOCUS
In Focus menu, you can set up the focus mode among Auto, Manual or One Push.
③WHTE BALANCE
White balance setting is a function revising color temperature to resolve the problem that screen’s colors
change
by the color temperature’s difference arrcording to time.
CAMERA MENU 1
FOCUS
D-ZOOM
WHITE BAL
BACKLIGHT
EXPOSURE
DAY/NIGHT
IRIS DET
DIS MODE
NEXT SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ FOCUS >
: AUTO
: ON
▷
: OFF
▷
: COLOR
▷
: OFF
4. 5. 1 CS-SD276DN Camera Setting
WHITE BAL MENU
▷ AWB MODE
RED OFFSET
BLUE OFFSET
COLOR SETUP
SHARPNESS
BACK
< NEAR / RIGHT ▷ AWB MODE >
: OUTDOOR
: ---
: ---
: 50
: 16
- AWB MODE : Select AWB mode.
- RED,BLUE OFFSET : Adjust the RED,BLUE OFFSET VALUE from 000 to 255.
It is available when the AWB MODE is in MENUAL
mode.
- COLOR SETUP : Adjust the brightness from 00 to 99.
- SHARPNESS : Adjust the sharpness from 00 to 32.
② Decide using of digital zoom function.
D-ZOOM: ON/ OFF
④ BACKLIGHT : Select the OFF, HIGH, MID or LOW .
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :

20 21
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
⑥ DAY/LIGHT : Select AUTO, COLOR or BW.
EXPOSURE MENU
▷ BRIGHTNESS
SHUTTER MODE
SHUTTER SPD
AGC
AGC LEVEL
SSNR
SENS-UP MODE
SENS LIMIT
BACK
< NEAR / RIGHT ▷ BRICHTNESS >
: 50
: ESC
: ---
: MID
: ---
: MID
: AUTO
: X4
- BRIGHTNESS : Select brightness from 01 to 99.
- SHUTER MODE : Select ESC,ANTI F or MANUAL.
- SHUTER SPD : Select shutter speed from 1/12000 to X128.
- AGC : Select OFF,LOW,MID or HIGH, MANUAL.
- AGC LEVEL : Select AGC LEVEL from 01 to 36.
- SSNR : Select OFF,LOW,MID or HIGH.
- SENS-UP MODE : Select AUTO or OFF .
- SENS LIMIT : Select from X2 to X256.
⑤ EXPOSURE
⑧ DIS MODE : Select ON or OFF.
- IRIS MODE : Select AUTO or MANUAL.
- IRIS VALUE : If you set the MODE in manual, the value can be set
from 00 to 99.
⑦ IRIS SET
CAMERA MENU 2
LINE LOCK
WDR ON/OFF
WER LIMIT
WDR LEVE
LENS INIT
FACTORY
BACK
▷
< NEAR / RIGHT ▷ FOCUS >
▷
: ON
CAMERA MENU 2
LINE LOCK
PHASE VALUE
BACK
▷
< NEAR / RIGHT ▷ FOCUS >
: ON
:
① LINE LOCK : Select INT or EXT.
PHASE VALUE : Select EXT menu.
②WDR ON/OFF : Select ON or OFF and set the LEVEL and the LIMIT value.
③WDR LIMIT/LEVEL
: Select LOW - MIDDLE - HIGH and set the LEVEL from 00 to 100.
④LENS INIT : Select YES or NO.
⑤FACTORY : Select YES or NO.
CAMERA 2 FUNCTIONS
- Select NEXT in the bottom of CAMERA MENU 1.
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
IRIS MODE
▷ IRIS MODE
IRIS VALUE
BACK
< NEAR / RIGHT ▷ IRIS MODE >
: AUTO
: ---
4. 5. 2 CS-SD276DN Camera Setting (2)

22 23
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
D-ZOOM (Digital Zoom)
- Magnification of the Digital Zoom can be switched On and Off.
- It is recommended that the Digital Zoom is set up before the preset operation.
- As the digital zoom magnification increases, the image quality is lowered.
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
< NEAR / RIGHT ▶ ZOOM SET >
▷
▷
▷
▷
▷
▷
▷
SAVE BACK EXIT
CAMERA MENU
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
< NEAR / RIGHT
▶
ZOOM SPEED>
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
< NEAR / RIGHT
▶
D-ZOOM >
ZOOM SPD : Select from 1step to 7 steps,
USER (Standard speed)
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
① ZOOM MODE
Zoom speed can be set and decide using of digital
zoom function.
② FOCUS
In Focus menu, you can set up the focus mode among Auto, One Push, Manual or Infinity.
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
FOCUS SET >
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in auto mode.
In auto focusing mode, zoom key operation is not
recognized as the input of the focus key.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically.
This is for focusing accurately after zooming.
Manual: In the manual mode, users can adjust the camera
focus manually.
Infinity: Infinity focus is the state where a lens forms an image of an object an infinite distance away.
This corresponds to the point of focus for parallel rays.
Set the speed for camera focusing.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
AF MODE SEL >
4. 5. 3 CS-SD227DN Camera Setting
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :

Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
24 25
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
AE SET >
③AUTO EXPOSURE
AUTO EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
AE MODE >
AE setting is a function that adjusts the shutter speed according to subject’s brightness to get optional
amount of exposed light.
AF MODE: Set the AF MODE.
SENSITIVITY: Set the sensitivity of focus
Set the near limit.
Select AUTO,MANUAL,SHUTTER, IRIS and BRIGHT.
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
SHUTTER SPD >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
SLOW SHT >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
IRIS LEVEL >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
GAIN LEVEL >
Select ON/ OFF.
If you set SHUTTER in the AE MODE, you can control image
brightness by adjusting shutter speed.
Set from 1/50 , 1/80 , 1/120, 1/150, 1/250, 1/500, 1/1000,
1/1500, 1/2000, 1/5000, 1/10000, 1/20000, 1/50000, 1/100000
x512, x128, x64, x32, x16, x8, x4)
If you set IRIS in the AE MODE, you can set the IRIS level
from 00 to 17 .
If you set MANUAL, IRIS and SHUTTER in the AE MODE, you can
set the GAIN for brighter image from 0~30dB. (Changable by 2dB)
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
AF MODE SEL >
BACK
< NEAR / RIGHT
▶
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

26 27
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
AGC MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
EXPO. MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
EXPO. LEVEL >
Select ON/ OFF in AGC MODE.
Select AUTO or Manual.
If you set ON in the EXPO MODE, you can control this level.
( "0" is standard (±10.5 selectable), changed by 1.5dB)
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
WB SET >
④WHTE BALANCE
Sets the white balance of camera.
WHITE BALANCE MENU
WB MODE : AUTO
RED GAIN : xxx
BLUE GAIN: xxx
BACK
< NEAR / RIGHT
▶
WB MODE SEL >
WHITE BALANCE MENU
WB MODE : AUTO
RED GAIN : 025
BLUE GAIN: 025
BACK
< NEAR / RIGHT
▶
R GAIN SEL >
White balance setting is a function revising color temperature
to resolve the problem of the screen’s colors change
by the color
temperature’s difference according to time.
WB MODE: Set the color depend on white balance.
WB MODE : Select AUTO, INDOOR, OUTDOOR and
ONEPUSH,HWB,ATW and MANUAL.
RED GAIN: Adjust red color level from 0~255.
(Standard level is 025)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 025)
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :

28 29
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAMERA RESET
▶
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
ICR SET >
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :10
BACK
< NEAR / RIGHT
▶
ICR MODE >
⑤ICR MODE
Sets the LED operation depending ICR Mode.
Select AUTO, DAY and NIGHT mode and the LED will be operated depending on this mode.
Set the ICR THRESHOLD from 00 to 28 LUX.
MAIN MENU
< NEAR / RIGHT
▶
SPECIAL SET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
CAM RESET
▶
SPECIAL ▶
SAVE BACK EXIT
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
APERTURE >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
FLICKERLESS >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
BACK LIGHT >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
BACK LIGHT >
⑥SPECIAL
In the Special menu, it’s available to set APERTURE GAIN, BACK LIGHT, DAY&NIGHT MODE,
DAY&NIGHT LEVEL and WDR.
Set the APERTUREGAIN value .
Select ON/OFF in the FLICKERLESS function.
Select ON/OFF in the BACK LIGHT function.
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :10
BACK
< NEAR / RIGHT
▶
ICR THRESHOLD >
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :

30 31
Here you can clear programmed Preset, Tour, Scan, Pattern, Area, Alarm
and Privacy.
4. 6. 1 Preset
Clear all of memorized Preset data
4. 6. 2 Tour
Clear all of memorized Tour data
4. 6. 3 Scan
Clear all of memorized Scan data
CLEAR MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
▷
< NEAR / RIGHT ▷ PRESET >
▷
▷
▷
▷
▷
▷
4. 6. 4 Pattern
Clear all of memorized Pattern data
4. 6. 5 Area
Clear all of memorized Area data
4. 6. 6 Alarm
Clear all of memorized Alarm data
4. 6. 7 Privacy
Clear all of memorized Privacy data
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide
4. 6 Clear Menu
4. 7 PTZ RESET
MAIN MENU
< NEAR / RIGHT
▶
RESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
CAM RESET ▶
SPECIAL
▶
SAVE BACK EXIT
Initializes all setting values which are set in CAMERA MENU.
⑦CAMERA RESET
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
V PHASE >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
DNR LEVEL >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
▶
WDR MODE >
If you set ON in the LINE LOCK menu, you can set
the V PHASE.
Set the DNR LEVEL from AUTO, OFF and 1 ~ 10.
Set the WDR MODE from OFF, LEV1 ~LEV7.
Select :
NEAR
Set :
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT ▷ MOTION >
→
→
→
→
▷
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :
Select :
NEAR
Set :

32 33
5. SPECIFICATION
5. 1 Mechanism Specifications
- Pan : 360° Continuous Pan, 0.1º to 90º/sec. (64 steps proportional to zoom)
- Pan Preset Speed : 380°/sec, ± 0.1° Accuracy
- Tilt : 0.1º to 90º/sec. (proportional to zoom)
- Tilt Preset Speed : 150°/sec, ± 0.05° Accuracy
- Weight : Approx. 1.6Kg (4.7 lbs) / Packing : 2.0Kg
- Dimensions : 125(Ø) x 194(D) mm – 4.9(Ø) x 7.64(D) mm
- Ingress Protection : IP66 (Outdoor Housing)
- Construction : Aluminum
- Color : Cool Gray
- Operating Temp : Indoor : 0°C to 50°C (14° F to 122° F)
Outdoor : -20°C to 50°C (14° F to 131° F) / (W/Outdoor Housing)
- Storage Temp : -20°C to 60°C (-4° F to 140° F)
- Humidity : 0% to 90% (non-condensing)
- Fan / Heater operate : 35°C off , 45°C on / 10°C on , 20°C off
(Optional outdoor housing)
- Preset : 255 points, less than 0.1° accuracy
- Tour : 8 programmable
- Pattern : 4 patterns for 240 second.
- Auto Flip : Auto / Off (Rotate 90° at bottom of tilt)
- Scan : 8(programmable speed and diagonal scan)
- Privacy Zone :
8 blocks with title (Mask)
- Address : Up to 255 selectable ID (Rotary switch)
- Control :
RS-485 / RS-422, Multiple protocol (Auto detection)
2400, 4800, 9600, 19200. 38400, 57600 bps selectable
- Protocol : Multiple protocol (PELCO-D/P, WONWOO)
2400, 4800, 9600, 19200, 38400, 57600 bps selectable
- Alarm In :
8 alarm
- Alarm Out : 2 relay out
- Display : 16 Area title
Zone title on/off (start / end zone)
- Power :
24VAC 60Hz / 24VAC 50Hz (Power adaptor not included)
- Consumption : 18.0 W ( 1.0 A Max.)
- Heater : 33W or 62.7W (Optional outdoor housing)
- Fan : 3.4W (Optional outdoor housing)
- Power(Camera) : AC21V - AC28V, 50/60Hz - 15W Maximum
- Power(Heater) : AC21V - AC28V, 50/60Hz - 30W Maximum
- RS-422, 485 : + / - Optional Control Data
- Video : BNC
- Alarm Inputs : 8 Programmable
- Relay Out : 2 Dry Contact Output Rating: 1A 30V DC / 0.3A 125V AC
- CE EMC , FCC CLASS A, RoHS
5. 1. 1 MECHANICAL
5. 1. 2 ENVIRONMENTAL
5. 1. 3 FUNCTIONS
5. 1. 4 ELECTRICAL
5. 1. 5 USER CONNECTRIONS
5. 1. 6 CERTIFICATIONS
5. 2 Camera Specifications
5. 2. 1 CS-SD276DN
- Image Sensor
- Lens
- Total Pixels (HV)
- Effective Pixels
- Resolution
- Focus mode
- Iris mode
- Video Output
- Sync.
- S/N Ratio
- Min. Illumination
- SSNR
- Day&Night
- White Balance
- Lens Initialize
- Iris
- Gain Control
- Focal length
- Digital Zoom
- Min. Focus Distance
- Coverage Angle
: 1/4 inch Sony Super HAD CCD
: 27x Optical Zoom
: 811 x 508 (NTSC), 795 x 596 (PAL)
: 768 x 494 (NTSC), 752 x 582 (PAL)
: 600 TV Lines (Color) / 700 TV Lines(B/W)
: Auto Focus / Manual Focus / One-push AF
: Automatic with Manual Override
: Composite 1.0Vp-p, 75Ω, BNC
: Internal Sync
: Higher than 50dB (AGC OFF)
: 0.4Lux/F1.6(Color),0.02Lux/F1.6(B/W) /(@50IRE)
: LOW/MEDIUM/HIGH/OFF
: AUTO/COLOR/BW/EXT, IR-Cut Filter Removable
: ATW/AWC/MANUAL/INDOOR/OUTDOOR (1,800K~10,500K)
: Built-in
: AUTO/MANUAL
: LOW/MEDIUM/HIGH/MANUAL/OFF
: F3.5 ~ 94.5mm (F 1.6 to 2.9)
: OFF, ON (Limit 12x) (Total 324X Zoom)
: 1,500mm
: F=3.5mm 55.5°(Horizontal) X 42.5°(Vertical)
F=94.5mm 2.24°(Horizontal) X 1.79°(Vertical)
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

34 35
6. DIMENSION
Unit : (mm)Unit : (mm)
6. 2 Wall and Ceiling Pipe Plate
Unit : (mm)Unit : (mm)
6. 1 Camera Dimensions
PTZ mechanism Outdoor Housing In-ceiling Housing
329
188.4 63.8
Ø214.8
R83
Ø188
71.0 193.7
127.6
125.0
117
111
15
PF 1/4 THREAD
48
32
150
45
93
Ø35
90
120
PF 1/4 TAP
4-Ø8
32 86
280
150
Ø42.2
120
25
SPPS 32A Sch40
Ø48.3
90
2
Wall Pipe Plate
Ceiling Pipe Plate
5. 2. 11 CS-SD227DN
: 1/4" SONY Super HAD II(Double Scan) CCD
: 1028(H) × 508(V) (NTSC), 1028(H) × 596(V) (PAL)
: 2:1 Interlace
: 15.734KHz(H),59.94Hz(V) (NTSC), 15.625KHz(H),50Hz(V) (PAL)
: Internal / External (V-Lock)
: 700 TV lines (COLOR) / 800 TV lines (BW)
: Color : 0.5 lux , BW : 0.2 lux / Color DSS : 0.001 lux , BW DSS : 0.0004 lux
: 1.0 Vp-p (75 ohm, composite)
: More than 50dB (AGC off)
: 22x Day & Night Zoom Lens
: Optical 22x, Digital 32x Zoom
: f = 3.9 mm ~ 85.8 mm
: F1.6 (wide) ~ F3.7 (tele)
: Auto / One Push / Manual
: 0.1 / 1.0 / 1.5 / 2.5 / 6.0 m
: Off / Max 2x~32x
: 1/60 ~ 1/100,000 sec(NTSC), 1/50 ~ 1/100,000 sec(PAL)
: Off / Max 2x~512x
: Off / WDR / BLC
: Day / Night / Auto / Ext
: ATW / One Push / Indoor / Outdoor / Manual / Auto
- Image Sensor
- Total Pixels
- Scanning system
- Scanning Frequency
- Sync. System
- Resolution
- Min. illumination
- Video Output
- S/N Ratio
- Lens type
- Zoom Ratio
- Focal Length
- Aperture Ratio
- Focus
- Focus Distance
- D. Zoom
- Shutter Speed
- Digital Slow Shutter
- WDR / BLC
- Day&Night
- White Balance
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

7. CONFIGURATION
7. 1 Connecting to CS-KY2403 with DVR - 16. 3 Parapet Mount Bracket
6. 4 Corner Mount and Pole Mount Bracket
- Stainless steel(SUS) body
- Unit : 5.2Kg
- Silver color
- Maximum load : 20Kg
- Dimensions : 890x650 (Arm)
- 250 x 350 (Mount plate)
- 1.25 Inch to 1.5 Inch pipe adaptor
Corner Mount Bracket
Parapet Mount Bracket
- Steel body
- Unit : 1.3Kg
- Cool gray color
Pole Mount Bracket
- Steel body
- Unit : 0.7Kg
- Cool gray color
Unit : (mm)Unit : (mm)
Unit : (mm)Unit : (mm)
115
647.00
950.00
350.00
250.00
180
100 100 100
1.25 Inch
5.00
00
.0
3Ø
155.00
0
0.
5
81
5.00
0
0
.
00
1
00.04
90°
04.221
0
5
.
1
=
t
05.
1=t
0
5
.
86
155.00
00
.0
3
Ø
0
0.02 00.5
8
1
80
WH
B LS
L
O RB
R
B KY
L
R DG
R
36 37
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide

MEMO
T
7. 2 Connecting to CS-KY2403 with DVR - 2
38 39
Speed PTZ Dome Camera System Use's Guide
Speed PTZ Dome Camera System Use's Guide