Cam Scan CS-IRF7300 User manual

INSTRUCTION MANUAL
1/3" 960H 2:1 Interlaced CCD
610Kpixel High Resolution 700 TV lines
2D + 3D Digital Noise Reduction
Auto Switching IR LED control by photocell
Ø IR LED: 12pcs, 30pcs, 54pcs, 66pcs
DC12V operation
Weatherproof bullet housing IP66
(*) Use regulated & specified power supply.
T1 5x25 (4pcs)
L-Wrench
Bolt
INSTRUCTION
MANUAL
Professional IR 7000 Series
Professional IR 7000 Series
CS-IRF7300
CS-IRF7400
CS-IRF7500
CS-IRF7600
P/N : 388028353
700TVL DNR High Resolution
Video Surveillance Camera
700TVL DNR High Resolution
Video Surveillance Camera
Max. 90% RH
VBS 1.0Vp-p (75 Ω Load)
Color : 0.3 Lux, BW: 0.1 Lux
Internal
More than 48dB (AGC Off)
10℃~ +50℃
DC12V 10% ±
1/3＂520K Color IT-CCD
Power
Consumption
Power Supply(*)
Scanning Frequency
Operational Humidity
PALNTSCITEM
15.625KHz(H), 50Hz(V)
625 Lines 2:1 Interlace
1/50 ~ 120,000sec1/60 ~ 120,000sec
15.734KHz(H), 59.94Hz(V)
525 Lines 2:1 Interlace
Video Output
Min. Illumination
Lens
Sync. System
S/N Ratio
Shutter Speed
Resolution
Scanning System
Total Pixels
Effective Pixels
Image Sensor
Operating Temp.
700 TV Lines
Max.: 320mA/DC12V (IR-LED On)
Max.: 190mA/DC12V (IR-LED On)
Max.: 530mA/DC12V (IR-LED On)
Max.: 620mA/DC12V (IR-LED On)
30 LEDs
12 LEDs
54 LEDs
66 LEDs
f= 6mm F1.8 (Option: 4mm)
f= 4mm F1.9
f= 8mm F2.0
30 LEDs
12 LEDs
54,66 LEDs
518K pixels 607K pixels
482K pixels 568K pixels

To avoid smear, do not expose the camera
directly to a strong light source such as the
sun or spot light.
Caution!
1. Fixing the camera unit at the desired spot.
2. Connect the video & power cable to camera.
Please check below points before connection.
> Power supply
Adaptor : 500mA/DC12V(12,30LEDs), 1A/DC12V(54,66LEDs)
Regulated Power Supply
To avoid fire or shock hazard, use a UL listed power supply.
> Monitor Impedance
Set the impedance switch to 75Ωstandard position.
When monitor is set to high impedance mode, the picture may
become blurred.
In this case, check the switch position of monitor impedance.
3. Turn the camera direction to the object that you want to display.
1. SUNSHIELD BOLT
2. SUN-SHIELD
3. FRONT CASE
4. REAR CASE
5. BRACKET
6. VIDEO/POWER
CABLE
Adjusting the camera view
11
2
3
2
5
3
5
6
4
46
POWER
VIDEO
POWER
VIDEO
ADJUSTMENTS
③ PAN: Adjusts view direction
② TILT: Adjusts view angle
①ROTATION: Adjusts screen view
- Loosen a screw on the side of bracket with a screwdriver and adjust the
camera angle as shown.
- Install the mounting bracket at the desired location.
Using supplied screws fix a bracket to the wall or the ceiling.
LED 12pcs, 30pcs
LED 12pcs, 30pcs
LED 54pcs, 66pcs
LED 54pcs, 66pcs
60
60
74 131
60
109
122