Cambro CAMSHELVING CSFLEXMERCH User manual

CAMSHELVING®FLEX STATION MERCHANDISER
OWNER’S
MANUAL
UMCSFLEX
D0718123
Telephone [phone] Toll Free 800 854 7631 Customer Service 800 833 3003
© Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056
Printed in USA 08/18
STEP 1
Remove the backIng paper from the
adhesive strip at each of the top
corners of the side panel (C/D).
IMPORTANT! BEFORE INSTALLING SIDE PANELS:
Ensure your Flex Station is completely set up with all divider bars installed in place for service with food pans/food boxes.
Once panels are attached, there is VERY limited access to be able to properly install or move divider bars on each side/end.
STEP 2
Carefully set top corners into a straight
position directly under the post
connectors and in a straight line down
each post then press firmly in place.
STEP 3
Remove the rest
of the backing papers and firmly press
both sides, from top to bottom.
Repeat 1-3 for the other side panel.
ACParts Checklist:
D
E
B
❏AFully Assembled Flex Station
❏BHeader with Aluminum Base Frame
❏CSide Panel with Menu/Info Holder
❏DSide Panel
❏EZip Ties (2) for Header Base Frame
Needed: Scissors or Cutting Pliers
PRODUCT CODE: CSFLEXMERCH
DIMENSIONS:
Side Panel: W23" x H56"
Header : L48" x H8"
Overall unit height when installed: 75 3/4"
Page 1
A. SIDE PANEL INSTALLATION
Premium Series Flex Station shown
with Optional Food Storage Boxes.

CAMSHELVING®FLEX STATION MERCHANDISER
OWNER’S
MANUAL
UMCSFLEX
D0718123
Telephone [phone] Toll Free 800 854 7631 Customer Service 800 833 3003
© Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056
Printed in USA 08/18
The Flex Station Merchandiser Panels are designed to withstand normal wear and tear from regular use. Each
panel has a protective, clear laminate top layer to protect graphics from dust, food debris, and also incidental
marks from regular use. It will not withstand damage from extreme contact with hard or sharp surfaces. It is
possible that ink marks, including Sharpie, may be removed with a standard commercial cleaner. The panels
will tolerate moisture and rain exposure but on a limited basis. Fading due to sunlight is possible over time. It
is not recommended to store Flex Station with Merchandiser in coolers or freezers.
To clean, use a soft, dry cloth for dusting, or a soft damp cloth and soapy water for more extensive cleaning.
Commercial products can be used for heavy duty cleaning but do not use solvent based products like acetone.
Panels should never be pressure washed. Panels can be removed for complete cleaning but it is not advised.
Remove adhesive on unit with standard glue removal cleaner. Re-installation of panels requires operator to
supply adhesive strips and zip ties to re-attach panels and header to the unit.
Cambro Manufacturing warrants its new products(s) to be free from defects in material and workmanship for
a period of one (1) year from the date of shipment from authorized CAMBRO distribution locations.
STEP 3
Thread 1 zip tie up through the inside hole, out
over the post connector, down into the outer hole
and tuck it back in above the side panel.
STEP 4
Thread the zip tie into the open end and pull tight. Repeat 1-4 for the other end
of the Header Metal Base. Check the Header position for any movement and
tighten the zip ties if necessary. Once secured into place, snip off excess zip tie
ends with scissors or cutting pliers.
STEP 1
Remove all adhesive backing paper
from the Header Metal Base.
STEP 2
Position Header Metal Base on top front of the Flex Station, moving it all the way forward
to rest firmly against the back of the post connector tops. IMPORTANT! Before pressing
down into place, there are 2 holes on each end of the Metal Base - 1 should be on the
outside of the post connector and one should be on the inside.
Care and Cleaning
Warranty
B. HEADER PANEL INSTALLATION
Page 2